Search Documents

By Ali Ebrahimi, Meena L. Viswanath, John F. Beech, Mustafa B. Erten, Ming Zhu

"Excessive deformation of a cantilever sheetpile wall can occur due to dredging, excavation, backfilling, or long-term creep behavior of soil. A buttressing berm constructed in front of the wall can be considered as a mitigation technique to prevent or decrease the deformation by increasing the passive earth pressure and thus improving the wall stability. The effect of the buttressing berm on the stability and deformation of a sheetpile depends on the berm geometry (i.e., the thickness/depth and the width) as well as the properties of the sheetpile and the adjacent soils. A parametric study was conducted using a conventional limit equilibrium method. Design charts were prepared to evaluate the effect of a buttressing berm and the soil friction angle on the wall stability and deformation. These charts can be used as a tool by geotechnical engineers to make a quick estimate of the required size of a buttressing berm in case of calculated or unexpected excessive deformation of a sheetpile. An analysis of the effect of a buttressing berm on the stresses and deformation of a sheetpile was also compared with the results from finite element analysis. The results of this comparison are discussed.INTRODUCTIONCantilever sheetpile walls are commonly used to support excavations. Sheetpiles are hot rolled or cold formed sections of steel made to interlock with adjacent sections to form a continuous structure providing lateral support. Sheetpile walls can be cantilever walls or anchored with tiebacks. To construct a cantilever sheetpile wall, sheetpiles are driven by pile drivers or vibrated in to a design depth sufficiently below the depth of excavation. Excavation can then proceed in front of the sheetpile wall, which resists the earth pressure loading from behind the wall. The design depth and geometry of the sheetpile wall depend on the soil conditions, the depth of excavation, and the tolerable deformation. In certain cases, when a small buttress of soil can be left immediately adjacent to the sheetpile wall, the required depth or geometry of the sheetpile wall can be reduced or adjusted, which can significantly decrease the cost of procuring and installing the wall. Such a buttress can also serve as a short-term or long-term remedy in case of observed excessive deformation in a constructed wall. Traditional methods of analyzing the stability of a sheetpile wall do not account for the passive pressure effects of this small buttress. In this paper, a parametric study was performed for a variety of soil types and wall and buttress geometries by implementing traditional limit equilibrium methods in commercial software and design charts were created illustrating the effect of a buttressing berm on sheetpile deflection. Selected cases were then modeled in a finite element software to compare the results with the traditional limit equilibrium method. The resulting design charts can be used as a tool by geotechnical engineers looking to reduce the design geometry of a sheetpile wall or address observed excessive deformation in a constructed sheetpile wall."

Jan 1, 2016

By J. E. De Waele, J. J. Lee, M. J. Mulheron, Luke R. Deamer

There is increasing demand for geotechnical contractors to commit to carbon reduction, net zero or science based targets. A lot of focus has therefore been placed on using low carbon materials and low emission rigs. However, whilst these are ways to help reduce carbon, there is a need to look beyond just substituting materials and fuels to meet net zero. Using the IEMA carbon hierarchy, there is a need to first look at eliminating and reducing emissions, before considering substitute materials. For example, in geotechnical designs, this may mean considering using ground improvement or reducing the number of piles, before considering using low carbon cements. Equally, for remaining emissions, this hierarchy means considering carbon negative products to offset emissions, such as ground source heat pumps. This hierarchy can also be applied throughout geotechnical contractor organisations. For example, considering video conferencing for meetings, before considering public transport or using an electric vehicle. This article explores the carbon hierarchy and how it can be applied to all areas of a geotechnical contractor’s business. Only through embedding this hierarchy across the business can geotechnical contractors achieve the step change required to meet net zero.

May 1, 2022

By Brenton Cook, Daniel Mageau, Larry Applegate, Aaron McCain

"Ground freezing was successfully used to create an impermeable barrier wall along 3,000 feet of the downtown Seattle waterfront as part of the Seattle Seawall Replacement Project. This $360 million re-development involved removing the original 1930-era seawall and replacing it with a new, seismically resistant concrete wall supported on fill soil improved by jet-grout. The replacement wall was one of the largest construction projects in the state of Washington at the time. Ground freezing is typically used as both a structural shoring wall and groundwater cutoff. However, at this project it was used primarily as a cutoff wall to stop groundwater seepage into the 16-foot deep excavation from the landside areas.The project was divided into ten boxes (sections), each typically 200 to 600 feet in length. Only a few boxes were under construction at one time to reduce the impact on tourist-dependent local businesses. Soil conditions in the freeze zone consisted of sand, gravel and silt fill with abundant wood and debris. Tidally influenced groundwater, much of it contaminated, was difficult and expensive to control using wells during initial stages of construction. For all subsequent stages, a frozen soil wall extending to about 35 feet in depth was used to stop groundwater seepage into the excavation. An additional benefit of ground freezing included elimination of potential settlement beneath nearby buildings, utilities, and the Alaskan Way Viaduct that would likely have occurred with the use of conventional dewatering wells. The frozen soil wall crossed more than 130 buried utility locations (including water, sewer, storm, electrical, fiber optic, phone, gas, steam) with no damage. The frozen soil wall was very successful and limited groundwater influx from the landside to the seawall excavation to a negligible amount so that pumping, storage and treatment of contaminated groundwater was essentially eliminated."

Jan 1, 2016

By Bernard B. Vannoy, Howard W. Gault, Ramesh Bobba

"Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. This paper describes the methodology employed by the JV and USACE to evaluate the overlap, thickness, and position of the barrier wall. It addresses the contractual requirements, positional uncertainty, and evaluation procedures.These procedures evolved over the course of the project as various issues were identified and procedures developed to evaluate these issues. During the project, it became clear that the JV and USACE could ascertain that the wall thickness and overlap requirements could be met if the overlap based upon Koden data was at least 0.7’ in the left-right direction. For a small number of piles with overlaps between 0.5’ and 0.7’, the piles are contractually compliant yet contain a minor degree of uncertainty in the overlap. Initially, the USACE assumption was that the amount of uncertainty of verticality measurements would require more than a 1-foot measured overlap in the left-right direction to confirm an actual, contractual 6-inch overlap. With time and experience, the limit of measured overlap was reduced in accordance with greater understanding of the equipment capabilities and tolerances. Other lessons learned include the need for Quality Control/Assurance personnel to collect data at the same starting point for every pile.For every pile the JV and USACE compared analog and digital data to provide confidence that the correct digital data was used for overlap calculations. Perhaps the most important lesson learned was the importance of the JV and USACE working together and sharing all data. Overlap analysis was performed by the JV’s Barrier Wall Specialist and a small number of USACE personnel. This resulted in a high level of experience and expertise within a small group.IntroductionThe Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep, and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. The wall was installed through a 6-foot wide Protective Concrete Embankment Wall (PCEW) which was installed two feet into rock. The PCEW protects the embankment from erosion of drilling fluids during subsequent operations. Below the PCEW the piles were installed to a specified elevation (staggered at 475’ and 473’ below the 748.2’ work platform). The Ordovician limestone and shale bedrock is flat lying with few vertical fractures. These conditions facilitate the advancement of pilot holes with very low deviations (with considerable credit to the JV’s drillers and steering engineers). The pilot holes were spaced on 31.5-inch and 35-inch spacing. Subsequent enlargement of the pilot holes to 50’ resulted in a continuous wall. This paper addresses the requirements and procedures to assure that the wall was as wide, deep and continuous as specified."

Jan 1, 2015

By J. G. La Fonta

The rapid development of real-time monitoring technology for the construction of large underground structures in urban areas can be attributed to: the zero-risk objective, the need for transparency between all parties involved and the control of real cost within the budget. Real-time monitoring can be an integral part of the construction contract (for example when compensation grouting is required) or independent, in particular when measurements of existing structures and buildings bordering the project are to be taken before construction starts. Three examples of extensive field instrumentation schemes are described: a large road tunnel in the Moscow suburbs, a new metro line in Amsterdam and major redevelopment works at a busy Central London rail interchange.

Jan 1, 2006

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By Harry Schnabel, Mitchell L. Fong, Douglas R. Jenevein, Thomas S. Lee

"The Warm Springs Extension (WSX) is one of a series of projects that will eventually extend the Bay Area Rapid Transit System (BART) from Fremont to San Jose, California. A cut and cover tunnel was used for a portion of the extension that runs through Fremont Central Park to minimize the impacts that an at-grade railway would have on the Park. A cement deep soil mix (CDSM) wall was selected by the engineer as the preferred method of providing structural support and groundwater cut-off for a portion of the tunnel where it passes through an important aquifer and near Lake Elizabeth. In addition to the CDSM wall, a jet grout plug was constructed at the base of the tunnel to provide a complete groundwater cut-off.This paper will discuss the unique quality assurance and quality control measures taken for the soil mix wall and jet grout plug as well as the methods used to repair leaks and mitigate water seepage through the exposed wall and grout plug.PROJECT DESCRIPTIONThe Bay Area Rapid Transit (BART) Warm Springs Extension (WSX) project is located south of the existing Fremont BART station extending 8.9-km (5.4 miles) to Warm Springs District in Fremont, California. The WSX project has been divided into two contracts with different delivery methods. In order to minimize impacts to Fremont Central Park, a subway was selected at this portion of the alignment under a conventional design/bid/build contract.The Fremont Central Park Subway (FCPS) which begins on the south side of Walnut Ave and ends just north of Paseo Padre Parkway and is about 2.3-km (1.4 miles) long. Fig. 1 shows the entire WSX and the FCPS project. The FCPS contract consists of a cut-and-cover subway box, subway transition structures, ventilation structures and a section of which transverses Lake Elizabeth (a man-made lake). The geologic conditions consist of fill (sand, silt, clay and construction debris), Young Alluvium (clay and silt), Basin Deposits (clay, silt, and sand), and Older Alluvium (sand and gravel) as shown in Fig. 2.HYDROGEOLOGY OF THE PROJECT SITEThe FCPS is dominated by two geologic features - the Hayward Fault and the Above Hayward Fault (AHF) aquifer. The AHF aquifer provides a significant source and storage of water for the local water district. The underground subway will penetrate this aquifer and is up to 11m (36 ft) below the groundwater table. No groundwater was allowed to be pumped during construction of the subway box by Alameda County Water District (ACWD). To facilitate excavation for the subway box, temporary cut-off walls and a grout plug were designed to retain and resist high differential hydraulic pressure. The following section describes the selection of a deep soil mixing method for water cutoff. Design of the grout plug has been described in Lee, et al., 2011 and Fong and Lee, 2009, and is not the focus of this paper."

Jan 1, 2015

By Nagarajan. D, Raja Rajan. K, Vijayakumar. T

Major bridges crossing mighty rivers must be constructed in flowing water. Constructing the sub-structure in water has been a challenging job for contractor. Special construction techniques with marine fleets to be adopted for waterfront construction. Enabling works like temporary piling platform and cofferdam used for pile and pile cap construction. Apart from this, enabling works like load out jetty to transport the materials from land to water; temporary walkway for access of workman to work location; temporary access bridge for construction vehicles movement; temporary liners for tower crane foundation; Concrete block to act as dead man anchor for barge movements were all required by the contractor for smooth functioning of site as per construction schedule. Investment in enabling works by contractor plays a significant role on profit margin of the project and of course with utmost safety. Design of enabling works for waterfront structures involves hydrological data like afflux, bathymetry survey, current force, scour depth and wave force to be taken cautiously for safe and economic design. Type of foundation and pile/well cap top level corresponding to water levels shall influence the construction scheme. Usage of geotechnical software like Wallap and Plaxis required for enabling work design to enhance the safety of the structure. Bathymetry and soil condition play a critical role in design and construction of enabling works. Water Discharge quantity in river along with water levels like low water level, high flood level, seasonal fluctuation of water levels has a great impact on design of enabling works. Establishing enabling works for waterfront construction near to an existing bridge is an additional challenge for the contractor. Along with design, constructing the enabling works in water requires special construction methodology and sequence of work. This paper shall provide insights on overview of design and construction of enabling works for waterfront construction.

Nov 1, 2022

By Louay Owaidat, Daniel Jabbour, Allan Frappier, Jose Gomez, Mark Stanley, Tino Maestas

The U.S. Army Corps of Engineers (USACE) is implementing a levee strengthening program along the Sacramento River East Levee (SREL) designed to correct 11 miles of deficient levees as identified by recent hydraulic and geotechnical investigations. The first project, the subject of this paper, completed in 2020 resulted in approximately 3.0 miles of improvements to the California Central Valley Flood Protection system. The project area lies along the east bank of the Sacramento River in Sacramento. The program consists of constructing cutoff walls through existing levee embankments to remediate levee through seepage and under-seepage. Key challenges included designing and constructing measures to remediate a 100-year-old legacy levee system, the presence of both industrial and residential properties immediately adjacent to the landside of the levee creating severe space and access limitations, and performing this work during the 2020 statewide mandate to shelter-in-place due to the COVID-19 pandemic. The project team of contractors, USACE, state and local agencies, and engineering firms partnered to bring this project to successful completion within budget and on schedule expending more than 60,000 man-hours with no lost time accidents. With the issuance of future planned contracts, the program will significantly reduce flood risk to the City of Sacramento.

Sep 8, 2021

By Mohsen Elsayed, Amr Sallam, Ahmad Mohamed, Xuebing Zheng, Mohamed Alrowaimi

The foundation is an essential component of the wind turbine that ensures continued operation under stable and safe conditions. Both shallow and deep foundations are utilized to support wind turbines including gravity spread foundation, anchor foundation, pier or drilled shaft foundation and pile and pile cap foundations. Conventional methods were typically utilized to design the wind turbine foundations. With the advances in numerical modeling in the geotechnical field, foundation designers may utilize numerical analysis to design wind turbine foundations. Geotechnical numerical packages allow modeling structural components and soil-structure interaction that is usually neglected in conventional methods. Furthermore, the subsoil conditions, geometries, stress-strain behavior, boundary conditions and load staging can be modeled, minimizing the assumptions and generalization. This results in better understanding of the stress strain behavior of the foundation leading to optimized foundation designs. This paper includes a brief review of current foundations used to support wind turbines with an emphasis on post tensioned single pier foundations. The current conventional foundation design methodologies and state-of-the-art foundation design utilizing numerical modeling of the single pier foundation will be discussed. Two case histories where the single pier foundation, designed using numerical modeling, were utilized to support the wind turbines will be presented. INTRODUCTION The foundation is an essential component of every wind turbine that ensures continued operation under stable and safe conditions. Turbine manufacturers provides load specifications for designers to be utilized for wind turbine foundations design. Loads include bending moments, torsional moments, lateral forces and vertical forces in both operational and extreme wind conditions. Essential specifications under seismic conditions might also be provided in seismic prone areas. Turbine manufacturers also include foundation design criteria including minimum rotational stiffness, minimum horizontal stiffness, maximum allowed inclination and maximum allowed lateral movement under both operational and extreme loads. Geotechnical explorations and evaluations are typically performed at early stages of the wind development projects. The field explorations usually include Standard Penetration Test (SPT) borings, Cone Penetration Test (CPT) Soundings, geophysical surveys, and laboratory tests to define soils stratification system and soil strength and compressibility characteristics. The most critical soil parameters for turbine foundation design are shear strength parameters (cohesion and friction), shear modulus, Poisson’s ratio, and unit weight. The depth to the groundwater table is also a crucial parameter in design. Advanced field explorations techniques such as Dilatometer Tests and Pressuremeter Tests may also be utilized. Laboratory tests for foundation design typically include index parameters, consolidation and triaxial tests.

Jan 1, 2019

By Jerry A. Steding

How many times have you heard "You can't drive piles because of the vibration."? You hear these words come out of the mouths of owners, engineers, and contractors. When a piling contractor hears this, he can almost always do a psychological profile of the individual uttering these words of wisdom. If the owner makes the statement, we know the odds are about 95% that the owner owns the building next door or he wouldn't care what happens to it; or the guy next door has threatened to sue the owner if he even so much as walks across the site of the proposed new building. If the owner owns the building next door to the new construction you can also be just as certain the old structure has undergone settlement. If the statement comes from the mouth of the contractor, it is usually just a case of him being inexperienced.

Jan 1, 1988

By Steve Davidow, Scott Tunison

As the demand for electric power grows and generation facilities are constructed in more remote areas, the industry faces an increasing number of foundation construction challenges. The importance of quality geotechnical information prior to construction is accentuated by the linear nature of the projects and the potential for drastic changes from one end to the other, but is often difficult or unfeasible to obtain. Alignments are crossing remote, rugged and/or environmentally protected terrain, and completing a comprehensive geotechnical program is made challenging from an access or economic standpoint, or both. In these situations, the industry needs a flexible foundation alternative. This paper will present micropiles as that alternative and demonstrate how the implementation of micropile foundations mitigated these challenges on the Koolau-Wailupe 46 kV Circuits in Oahu, Hawaii, which involved rugged, steep slopes and helicopter construction methods. It will detail the selection of micropiles over other foundation options, micropile and steel pile cap design methodologies, foundation construction, and quality control. Special attention will be given to the unique geology in the area, and why precise identification of saprolite and basalt layers was integral to the successful performance of the foundations. The intention is to communicate the benefits of a flexible solution based on continuous collaboration between design and construction.

By Howard A. Perko, Margaret Dring, Gerald Verbeek, Scott Slaughter

Helical piles have become a widely used deep foundation system in recent years due to their many inherent advantages. The cone penetration test (CPT) is commonly used in geotechnical practice to evaluate subsurface conditions for deep foundation design as the method provides a continuous soil profile in a short amount of time, measures in-situ soil strength, and in many ways behaves similar to a “mini pile” during penetration. In the CPT test, an instrumented cone is hydraulically advanced into the soil at a constant rate. As the cone is advanced, strain gauges embedded in the cone body continuously measure the tip resistance and side friction. In addition, a piezometer element is commonly used to measure the (dynamic) pore water pressure in the soil as the cone is advanced. A study was conducted comparing the CPT tip resistance to helical pile installation torque and capacity. In this paper, the outcome of this study was compared with historical data of helical pile installation torque records, static analysis predictions using commonly used techniques, and pile load test results over a wide range of soil conditions. A literature review was also conducted where a comparison was made for CPT tip resistance and helical pile installation torque data with previously published correlations.

Sep 8, 2021

By Terry Eldridge, Keith MacKay, David Siddle, Luke Moger

On August 4th, 2014, a breach occurred in the Perimeter Embankment of the Tailings Storage Facility (TSF) located at the Mount Polley Mine, releasing approximately 10.6 million m3 of supernatant water, 7.3 million m3 of tailings solids, 6.5 million m3 of tailings interstitial water and 0.6 million m3of construction materials. A Temporary Upstream Rockfill Berm was constructed between August 2014 and February 2015 within the area of the tailings dam failure in order to retain the remaining tailings solids during the low flows of the winter season. The Temporary Upstream Rockfill Berm was constructed as part of the initial response phase, with the primary objective to abate the flow of tailings into the receiving environment. A secondary objective of its construction was facilitating the required investigation works downstream of the tailings dam failure. The selection of the coarse grained material used in the construction of the Temporary Upstream Rockfill Berm was based on the availability of the material (timeliness of construction) and the non-water retaining design of this initial response phase. Consequently, an alternative method was required in order to prevent further loss of mine-affected water and tailings from the TSF, as well as to provide short-term contingency water storage, during high flow conditions expected in late spring. Golder Associates Ltd. designed the 2015 Freshet Management Embankment, a deep mixing cut-off wall, to meet these site requirements, which was constructed by Mount Polley Mining Corporation and Golder Construction Inc. between December 2015 and April 2015. The works included 132 soil cement panels constructed to depths of up to 27 meters. This aspect of the works was completed using an RG25S Bauer CSM rig on a 24 hour per day, 7 day per week schedule. The cut-off wall specifications included a target unconfined compressional strength (UCS) of between 1 and 2 MPa, a maximum hydraulic conductivity of 1x10-6 cm/s, and a ductility to enable the soil cement to undergo a minimum of 5% strain without a reduction in strength or increase in hydraulic conductivity. In order to control and assure the quality of the soil cement, 2553 wet grab specimens were retrieved from the fresh soil cement panels using a project-developed sampler. Four of the soil cement panels were cored with a mud-rotary drill rig and optical and acoustic televiewers were placed into the boreholes in order to log several relevant parameters, including image, texture, relative hardness, borehole-shape, and temperature.

Jan 1, 2016

By Filippo Maria Leoni, George Filz, Wesley Schmutzler, Matteo Bertoni

"The US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilization at the LPV 111 Project (New Orleans, USA). DMM was used for ground improvement/foundation strengthening and consequently to stabilize and support the burden of the new levee. Two different technologies were used: Trevi Turbo Mix (TTM) and Contrivance Innovation Cement Mixing Columns (CI-CMC). LPV 111 is the largest soil mixing project to date in the USA with its more than 18,000 elements installed to a depth of up to 67 feet for a total of 1.7 million cubic yards of treated soil. The preparation and execution of the project presented many challenges from various points of view. The little time available to complete the job led to the simultaneous utilization of eight deep mixing rigs and batch plants which worked 24 hours per day, 5.5 days per week on a stretch of land approximately 5.3 miles long. Given the imposing geographical extent of the project, a four phase laboratory programme and five field validation test programmes, conducted in as many different areas of the project, were completed to design and optimize the grout mixes and the installation parameters. The massive quality control/quality assurance testing programme produced over 500 drilled core holes and over 5,000 tested specimens in order to determine unconfined compressive strength (UCS) and uniformity of the DMM elements. This paper has the purposes of describing the tremendous challenges encountered and providing valuableinformation that may be useful for other future projects, including details not previously published.INTRODUCTIONReach LPV-111 is part of the Lake Pontchartrain and Vicinity Hurricane Protection System designed to protect the city of New Orleans and the surrounding areas from the surge that would accompany a 100 year hurricane event. LPV-111 measures approximately 8.5 km (5.3 miles) long, of which 7.2 (4.5 miles) extend along the north bank of the Gulf Intracoastal Waterway (GIWW) and the remaining 1.3 (0.8 miles) run north and terminates at the CSX Railroad Gate. The Bayou Sauvage National Wildlife Refuge borders the levee on both sides (Fig. 1)."

Jan 1, 2015

By Chunli Wei, Mark Jen, Xiaojun Wang

"After more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges. Each bridge includes 1,650 feet long signature steel composite cable-stayed bridge, a 2,789 feet long New York approach and a 1,889 feet long New Jersey approach. The superstructure of each approach is supported on a series of two-column concrete piers and each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock.A performance-based methodology was followed for the strength and extreme event limit states design of the drilled shaft foundations. The design for seismic loads has been performed using the AASHTO Guide Specifications for LRFD Seismic Bridge Design. For all strength and service loads, the AASHTO LRFD Bridge Design Specifications were used. Since the longitudinal and confinement requirements in the two specifications vary, the minimum longitudinal reinforcement was based on the more stringent requirements of the two codes. A design example is presented to illustrate the methodology in bridge deep foundation design using nonlinear time-history global analysis results with soil-pile interaction represented by sets of horizontal and vertical nonlinear soil springs along the drilled shaft, based on the soil and rock properties from the boreholes test results. In this paper the design methodology implements strain limits related to earthquake intensities and damage levels to calculate the capacity using XTRACT analysis, which aids designers to adopt applicable provisions that meet specific design requirements.INTRODUCTIONAfter more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges designed to carry vehicular traffic and a future mass transit corridor. They include two 1,650 feet long signature steel composite cablestayed bridges with 260 feet tall V-shaped concrete gateway towers (Figure 1). The approaches consist of continuous pre-stressed concrete girders. The New York approach is a single structure consisting of 18 continuous spans, sloping at 4% for a total length of 2,789 feet without expansion joints. Similarly, the longest continuous portion on the New Jersey approach, with a similar slope, consists of 11 spans for a total length of 1,889 feet without expansion joints. The superstructure of each approach is supported on a series of two-column concrete piers that vary in height from 121.3 feet near the cable-stayed bridges to 11.8 feet near the abutments. Each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock."

Jan 1, 2016

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019