Search Documents

By Kevin Kuhl

With the destruction of the US-90 Bridge spanning St. Louis Bay by Hurricane Katrina, the State of Mississippi awarded its first major design-build contract in order to have a completed four-lane bridge in a period of less than two years. The structure consists of 76 pre-cast concrete beam spans with a total bridge length from Bent 1 to Bent 77 of 11,124 ft (2.1 miles). All 77 bents are founded on pre-cast, pre-stressed concrete piles and consist of two foundation types: pile bents and water line footings. A total of 53 pile bents were utilized where the deck is less than 52 ft above the water. Further divided, 10 pile bents, supported by 24 in. square, solid piles, are located on land. The remainder of the pile bents are located within St. Louis Bay and supported by 36 in. square, voided piles. All the waterline footings are supported by 30 in. square, voided piles. In total, 138 -24 in., 437 -30 in., and 463 -36 in. piles support the structure. Production pile design was based upon information gathered from the subsurface investigation, design soil profile and 23 out-of-position test piles. Verification of the design was established by monitoring the first production pile driven at each bent using the Pile Driving Analyzer. Particular challenges included highly variable coastal deposits, loads in excess of 1600 kips per pile and a compressed construction schedule. Initial drive capacity of a portion of the production test piles was less than expected resulting in a minimum 14 day setup. Following the setup period, restrikes were necessary to verify capacity. Project production piles ranging from 50 ft in length to in excess of 160 ft in length were used to achieve the required resistance. This paper includes a brief overview of the foundation design and indicator test pile program. The main objective is to provide a summary of the quality control procedures including establishing the driving criteria for each bent and to present issues that arose during production pile driving and the solutions that followed.

May 11, 2007

By Patrick K. Wong, Richard Kelly

"The variability in strength and compressibility of in situ deep soil mixing products can be greater than the variability of the natural soil. However, satisfactory performance can be achieved by careful construction and an appropriate QA/QC program. This paper presents a case study on the use of deep dry soil mixing columns to support several embankments over soft clay along a highway project. Post-construction settlement monitoring indicated that good performance is achieved where the acceptance criteria are met, except in an area with high organic content. Embankments with contrasting performance are compared to the quality control test results which comprised laboratory testing of core samples as well as in situ test results such as pull-out and push-in vanes and conventional cone penetration tests. Drawing on the performance results and quality control testing, discussions and guidelines are given on quality assurance acceptance criteria and construction control testing regime for future projects.INTRODUCTIONBetween 2008 and 2012, the largest deep dry soil mixing (DSM) contract during that time in the southern hemisphere was carried out for the Ballina Bypass project. The project, comprising 12 km upgrade of the Pacific Highway located in northern New South Wales close to the border of Queensland, was commissioned by the Roads and Maritime Services (RMS) of NSW. The ground improvement contractor was Keller Ground Engineering (KGE) Australia. Seven different types of ground improvement techniques were employed for the project, ranging from low embankment strategy with nominal preloading, to surcharge with wick drains, light weight bottom ash fill, DSM, vibro-replacement stone columns, dynamic replacement, and vacuum consolidation (installed by Menard Bachy Pty Ltd). Different techniques were chosen depending on time program, cost, and performance requirements relative to proximity to piled structures (e.g. bridge abutments) and post-construction settlement and differential settlement for either rigid or flexible pavements at different locations.DSM was the most utilized ground improvement technique employed on the project, comprising a total of about 285 km of 0.8 m diameter columns to depths up to 18 m for the purpose of supporting bridge approach embankments and culverts with embankment heights up to 6 m. DSM was chosen due to the very soft nature of the clay soil with moisture content practically at liquid limit, and the relative speed and economy of the system. Dry cement powder at rates of 160 kg/m3 to 200 kg/m3 were pneumatically discharged via the hollow stem of the mixing tool, and mixed with the soil (using multiple horizontally mounted paddles on a single vertical stem) at high speed as the mixing tool is withdrawn."

Jan 1, 2015

By Terrence M. Carroll, Chu E. Ho

"A pile installation and load testing program on driven tapered piles was undertaken at John F. Kennedy International Airport in New York City for the extension of the existing Terminal 4. As part of the program, dynamic testing by means of the Pile Driving Analyzer (PDA) was performed on several preliminary test piles as well as production piles. The results of the dynamic tests and subsequent static load tests were reviewed to develop an understanding of the pile-soil response of a tapered pile during driving and after setup. Pile setup occurred as a result of increase in shaft resistance with virtually no increase in toe resistance. More than 150 tons of additional capacity was gained after the setup time.The capacities measured during driving from the PDA are typically used as the basis for determining the pile driving set criteria, with the required initial driving capacities determined largely by the contractor’s experience. An improved appreciation of the setup phenomenon is required to better refine the driving criteria at the end of initial driving such that the required ultimate capacities can be obtained, with reasonable confidence, after a period of setup.This paper presents interpretation of pile-soil behavior from Case Pile Wave Analysis Program (CAPWAP) analyses and discusses the mechanism of increased capacity as a result of setup effects. Time-dependent capacity gain as a result of setup effects should be based on the extrapolation of the shaft resistance component rather than the total pile capacity as is commonly practiced. Prediction of pile performance using this approach was in good agreement with observed static and dynamic load test results.IntroductionTapered piles have been adopted for various projects at John F. Kennedy International Airport (JFKIA) since the late 1940’s. Initially timber piles were used exclusively, with steel Monotube piles being used from at least the 1980’s (Horvath and Trochalides, 2004). The steel Tapertube pile was developed in the mid-1990’s and has commonly been used in recent construction (Brusey and Yin, 2008). The Tapertube piles used for this project consisted of a 25 foot long tapered section that was 8 inches in diameter at the tip and 18 inches in diameter at the top. An 18 inch diameter straight pipe was welded above the tapered section."

Jan 1, 2015

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Hee-suk Yun, Dae-jin Hwang, Jeong-woo Seok, Myoung-mo Kim

"In this paper, the accuracy of the data measured by a newly developed displacement measuring system, DPRMs (Digital Pile Penetration and Rebound Monitoring system) and its applicability as a quality control tool were verified by field measurements of pile penetration and rebound for pile driving performed at 3 construction sites and 1 test site. The DPRMs data were found to be much better than handwork data. A new dynamic formula for pile capacities is proposed uses the results of a pilot dynamic load test and the final pile penetration. The ratios of pile capacities obtained by the new formula to those by the dynamic load test were 94%±7.4% in the contrast with 123±28.3% by the 5S formula and 68±24.0% by Hiley's formula. This result shows the superiority of the new formula. The ratios of the maximum compressive stresses calculated by using DPRMs to those calculated by using PDA (Pile Driving Analyzer) were about 90-110±10%. This result confirms the applicability of DPRMs as an overdriving monitoring tool. Two sets of DPRMs were used to measure the 3-D displacement behavior of a pile head at the test site. The more the pile head moves laterally, the less the final set values were expected because of the loss of driving energy, but this trend was not obvious within the limited data obtained at the test site.INTRODUCTIONPile construction monitoring consists of two parts. In the first part, enough capacity of the pile is secured to stand the design load. In the other part, pile damage during driving is prevented. Although several methods can be applied to achieve the first part, PDA is nearly the only tool for measuring pile stress.Several methods such as a static load test, a dynamic load test, an Osterberg cell, and numerous driving equations can determine the pile capacity. Among them, the static load test and the dynamic load test are most widely used. The static load test is advantageous because it has the highest reliability. The disadvantages are as follows: it is costly and time-consuming. Also, the capacity of the pile under construction cannot be evaluated. The dynamic load test has lower reliability than the static load test, but it is cheaper than the static load test, is reliable enough to determine the pile capacity, can evaluate the capacity of a pile during construction, and can offer information about construction conditions such as the pile integrity and the pi le stress during driving. The dynamic load test takes a relatively short time and is low cost compared with the static load test. However, it is still costly, time-consuming, and unnecessary to apply to all piles in the field as a construction measurement tool. Therefore, driving resistance (blowcounts) is commonly measured to confirm the pile capacity at construction sites."

Jan 1, 2005

By Albert Neumann, Franz-Werner Gerressen, Giancarlo Santarelli

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. In addition they are also quite often used as deep groundwater barriers, named Cut-Off-Walls (COW). Due to the requirements of each particular job site, e.g. the need for carrying high loads or as seepage barriers, there is an increasing industry demand for efficiently cutting into rock. Besides the removal of boulders, cutting through rock, is always the most difficult part of the excavation process of a diaphragm wall or COW.There are a number of influencing factors which have an impact on the rock cutting performance. Besides the influence of the rock characteristics itself, which is not always the same, there are other factors related to equipment, tooling as well as the operating staff. In addition to RQD, the most commonly available rock property found in geotechnical reports is the Unconfined Compressive Strength (UCS) value. There are however some other related properties, such as weathering, bedding, inclination, abrasiveness, etc.,which can have a major impact on the achievable cutting performance. This paper will discuss the various parameters, and how they can be considered for performance estimation. Based on experiences gained on over 100 projects, a performance estimation chart was developed to allow for a better approach to these kinds of projects. This paper also explains the general installation process in as well as some specific features related to specific site conditions. In addition, some job site references will give more detailed information about such type of site conditions and how to deal with them.Keywords: Diaphragm wall, Cut-Off-Wall, Trench Cutter, RockINTRODUCTIONDiaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits, shafts, permanent foundation walls and load bearing elements.It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions.In addition diaphragm walls can also be used as deep groundwater barriers (Cut-Off-Walls). This market has demonstrated that the demand for these types of walls is reaching ever more difficult soil conditions and greater depths which are surpassing the current industry standards. The trench cutter is the most important tool for performing this type of work."

Jan 1, 2016

By Abu B. Siddique, Anthony S. Crincoli

"The New Jersey Turnpike Section 2 widening program consisted of widening between Interchange 6 in Mansfield Township, Burlington County and Interchange 9 in East Brunswick Township, Middlesex County. To accommodate large volume of traffic the roadway was widened from 6 to 12 lanes with major modifications performed at four interchanges. The Section 2, NJTA Interchange 6 to 9 Widening Program is a 4.2-mile section of Turnpike roadway which included a total of 12 new or modified structures. In order to facilitate the construction process Section 2 was divided into three construction contract packages. This paper will cover the last and final Contract T869.120.203 which is 1.7 miles in length. The work generally consisted of eight new ramps connection to and from the toll plaza to the new inner and outer roadways. New mainline bridges were constructed over several ramps. A new bridge was constructed to take northbound outer lanes traffic over two ramps along with new mainline bridges over Black’s Creek, Georgetown Road, and Laurel Run. In addition, a new bridge was constructed to take a ramp over Laurel Run and the existing U-turn Bridge was replaced with a new one.For Contract T869.120.203 a total of 74 five-foot diameter drilled shafts has been constructed to support all pier foundations for bridges. Three drilled shafts were tested using Osterberg Load Cells to verify the estimated shaft resistance during design phase. One Osterberg Load Cell test was performed on a demonstration (sacrificial) shaft and the other two Osterberg Load Cell tests were performed on production shafts. This paper compares the estimated total, side and tip resistances with corresponding measured total, side and tip resistances and provided recommendations for future design purpose.INTRODUCTIONTo accommodate large volume of traffic the New Jersey Turnpike Authority (NJTA) decided to widen Section 2, which included Interchange 6 through Interchange 9. The Section 2, a 4.2-mile section of Turnpike roadway that was widened from 6 to 12 lanes with major modifications performed at four interchanges.The New Jersey Turnpike Authority (NJTA) procured AECOM to perform engineering services for the final design of Section 2, NJTA Interchange 6 to 9 Widening Program. Section 2 is a 4.2-mile section of Turnpike roadway that will widen from 6 to 12 lanes and will include a total of 12 new or modified structures. It encompasses modifications of the existing and the design of four new ramps at Interchange 7. The project also includes the modification of two local roads over the mainline, two local roads under the mainline, two maintenance U-turns, and retaining walls. In addition, the project consists of the design of noise walls, sign structures, storm water management basins and the more typical drainage, utilities, lighting, roadway, ROW, and signing and striping design."

Jan 1, 2015

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011

By Paul J. Sabatini, Robert C. Bachus, Terence P. Holman, Panos Andonyadis

A recent landslide comprising approximately 12 acres (4.86 hectare) and a displaced volume of more than 500,000 cy (382,000 m3) caused the shutdown of a four-lane state highway and two high-capacity freight railway lines. After completion of immediate landslide stabilization activities, various long-term slope stabilization measures were implemented that focused primarily on gradual slope unloading in areas near and upslope from the scarp of the landslide. Near the completion of the upslope excavation, an anchored soldier beam and lagging wall was constructed to allow for the temporary unloading of the toe of the main landslide area to facilitate installation of a permanent underdrain. The design of the anchored wall utilized information collected during the rehabilitation construction and included inclinometer data, site survey results, piezometer data, and field construction observations. Using the history of site-specific movements, results of back-analysis calculations from the landslide, and geometry/performance of the post-construction slope configurations, the fully softened and residual shear strengths along two potentially critical sliding surfaces were calculated. Owing to the high confidence in the values of shear strength as afforded by this information, the confidence in local groundwater conditions, and control of the loads, the designers selected a relatively low, calculated short-term factor of safety (FS) (i.e., FS ˜ 1.1 to 1.2) for the most critical unloading step. Long term calculated FS values on the order of 1.2 to 1.3 were anticipated. This paper describes the detailed evaluation of the landslide slope movement data associated with the shallow and deep potentially critical failure surfaces and selection of the associated values of design shear strength for these potentially critical surfaces. A description is presented of the analyses and design of the anchored wall, measures implemented during construction to minimize slope movements, and post-construction monitoring results during the unloading and subsequent installation of the underdrain.

Jan 1, 2017

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015

By Federico Pagliacci

"Many existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or pervious rocks or karst. Remedial works are necessary in order to install new cut-off walls to stop the water flow. In some cases the cut-off walls have to be executed at depths never reached so far, and difficult to reach with traditional foundation techniques. In many cases the Hydromill technology proved to be the best system to overpass rocky layers and ensure the required verticality. The maximum depth reached by the industry was in the range of 120-150 meters. This article describes the test performed to excavate and cast in place a 3.2x1.5 m panel to a depth of 250 m. The article will also describe the stratigraphy of the site down to 250 meters, as well as the technique adopted to achieve the said depth with deviations from verticality of 30 cm along the longitudinal axis (0.12%) and 20 cm along the transverse axis (0.10%), measured at the bottom of the excavation. The concreting of the panel, for about 1,100 m³, with plastic concrete in the lower portion and conventional concrete in the upper portion will be illustrated. Finally, the tests performed during the excavation and after concrete casting will be also described, with special attention to the continuous directional core drilling that was performed along the whole length of the panel to verify the results of the deviation from verticality, through the onboard instruments, and to control the quality of concrete at a depth never reached before. IntroductionMany existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or caves and cavities or acid solutions in the bedrock formations.Conventional remedial works generally consist in the construction of an additional cut-off wall throughout the dam body and the subsoil, in most cases being deeper than the original one. Today, many examples of successful remedial cut-off walls allow the engineers to design the most suitable solution according to the dam and subsoil characteristics and nature.The real difficulty stems from the depth at which the new cut-off wall has to be socketed in competent rock or soil, so as to eliminate underwater seepage. The maximum depth ever achieved with a cut-off wall is 122.5 m for the remedial work of Mud Mountain Dam, Washington, USA, in 1988-1990. This 0.85-1.0 m thick cut-off wall was realized by means of a Hydromill, by excavating single 2.8 m-wide secant panels."

Jan 1, 2017

By Cheng Lin, Guoming Lin

"This paper presents a case history for the design, construction and long-term performance monitoring of a driven prestressed concrete (PSC) piled foundation supporting a large liquefied natural gas (LNG) tank in Savannah, Georgia, USA. Following a geotechnical investigation, a design stage pile test program was performed with three objectives: to study the densification effect from pile driving on the liquefaction resistance, to test axial and lateral pile capacities, and pile behavior under lateral loads. The test program comprised five piles driven on a test pad constructed adjacent to the tank foundation. Cone penetration testing (CPT) was performed before and after pile installation to test soil densification effects from the pile driving and liquefaction potential was re-evaluated based on the soil densities after pile installation. The axial load tests involved static load testing, high strain dynamic testing, and Statnamic testing. This paper presents the findings of the densification effects, compares results from different axial testing methods and discusses the procedures to use the load test results in the pile design. The paper also comments on the construction issues and presents performance data with 10 years of monitoring.1. IntroductionThe project site is located at the Kinder Morgan’s Elba Island LNG Terminal on the Savannah River which is three miles downstream of the downtown Savannah, Georgia. This LNG terminal was initially developed in the 1970s as an LNG import terminal. The facility includes five LNG storage tanks with two larger tanks which were constructed in 2003 and 2006, respectively. The terminal is currently being converted into a liquefaction and export facility. This paper discusses pile foundations for Tank D4 which is a double walled insulated steel tank built to hold one million barrels of LNG in 2003. This tank has an outer tank diameter of 258 feet, an inner diameter of 252 feet, and liquid height of 113 feet. A number of geotechnical challenges were present in the foundation design and construction.??The site is a typical coastal deposit site featuring a thick layer of very soft under-consolidated clay (up to 40 feet in thickness);??The bedrock is a couple of thousand feet deep;??There is a sand layer that is liquefiable under a high seismic design category (0.5% possibility of exceedance in 50 years)."

Jan 1, 1900

By Evangelia Ieronymaki

Civil engineering education relies on traditional methods of teaching, comprising mostly of deductive instruction by presenting the theory, followed by applications. This paper presents an alternative way for teaching foundation design to senior students, introducing a more inductive approach. The students are presented with a project/game adapted to a real-world problem at the beginning of the course. They are asked to identify the correct steps and methods throughout the lectures, for reaching an appropriate solution that they document and present at the end of the course. To make the project more enjoyable, the project has the format of a game where the students compete with each other on completing the task faster and more efficiently. The goal of this teaching approach is to enhance the ability of the students for problem solving and the engineering way of thinking, while playing a game. In the end, the students were requested to respond to a survey regarding the efficiency of this project/game on their learning. The results showed that students prefer more inductive methods for a design course, feeling that this project made them think more like engineers, while the ‘game’ twist of it made the whole course more fun. INTRODUCTION Most civil engineering courses are taught in 2019 the same way they used to be taught 40 years ago in the 80s. Classic methods are mostly deductive, where the instructor presents the theory first and then applications of that theory follow. Little or no attention is given initially to why the theory was developed or what are the problems it solves. The applications of the theory, and thus the purpose it serves, come only in the end and after methodologies have been presented, leading the students to show low interest in the material. As Albanese and Mitchell (1993) have reported, people are mostly motivated to learn things when they clearly see the need to know them. This explains the students’ little motivation that, if any, comes mainly from the fact that the material may be useful either in other courses or in their future careers. On the other hand, there are alternative inductive methods of teaching, where the role of the students is more active. A lot of researchers have highlighted the benefits of inductive methods in teaching engineering courses. Based on Prince and Fedler (2006), inductive methods include; a) inquiry-learning, b) discovery learning, c) problem and project-based learning (PBL), d) case-based teaching, and e) just-in-time learning. Inquiry-learning is maybe the most traditional method of inductive teaching/learning methods, where the instructor asks questions or poses problems and the students need to apply the theory they have learnt in order to find the solution (Bateman 1990; Prince 2004; Lee 2012). Similar to inquire-learning is the discovery learning, where students have to find the solution to a problem or answer to a question, while the instructor simply provides feedback to the students without guiding their efforts (Leonard 1988; Westbrook and Rogers 1994).

Jan 1, 2019

By Ronnie X. Gu, Xing Zheng, Gem-Yeu Ma

Due to implementation of the rotator construction method from which a smooth shaft was anticipated, a full-scale pile load test (Osterberg Method) was performed at Pier 14 Pile 9 of the main span of the New Benicia-Martinez Bridge to confirm the design parameters of the rock sockets. Two levels of load cells were fabricated in the reinforced cage of the rock socket. Each level consisted of three 670-mm Osterberg load cells with a total testing capacity of more than 50 MN in both directions. In an attempt to separate side friction and end beari ng, a 75 mm thick compressible Styrofoam material was placed at the bottom of the cage. The pile load test was carried out in four stages. The multi-level multi stage pile load test data was interpreted for casing friction, side friction for two rock strata, end bearing, and residual side shear values under repeated loading in opposite directions. The side friction from the casing in soils at Stage 2 is approximately 9 MN. The end bearing at the tip of the rock socket at Stage 3 was calculated to be approximately 17 MN at a displacement of about 75 mm. The residual side shear resistance for the 10 m 50% RQD rock strata was calculated to be 9 MN or approximately 50% of initial values, after being pushed 0.3 mm upward in Stage 1, 71 mm downward in Stage 2, then 55.5 mm upward again in Stage 3, and finally 105.3 mm downward in Stage 4. The test results surprising ly indicate that the side shear resistances from both low RQD intensely weathered rock and higher RQD slightly weathered competent rock are about the same at approximately 19 MN. This pile load test provides very critical information for confirming deep shaft design and analyses.

Jan 1, 2005

By Emre Biringen

"Results from a small-scale laboratory experimental program show the changes in the vertical stiffness and strength of a soft clayey soil adjacent to the shaft of an inserted pile (i.e. expansion of a cylindrical cavity). The experimental program provides a realistic axi-symmetric physical model of an element of a cylindrical pile and the surrounding soil. The study interprets the improvement and assesses its magnitude in vertical stress-strain-strength properties of a normally consolidated soft cohesive soil in response to preloading impact in the radial direction. The results verify that insertion of a cylindrical pile causes densification of surrounding soil in a radial direction due to change in stress state around the pile, and thus consolidating and stiffening of the soil.The test results indicate that most improvement in modulus and strength takes place within a distance of 4 times the radius of a pile, though significant improvement is realized to a distance of 8-10 times the radius, beyond where there is negligible effect. Settlement characteristics of the surrounding soil in a zone of 12 times the pile radius improve significantly after the formation of a cylindrical cavity. The miniature vane shear strength tests show a 1.5 times increase in a zone of 4 times the pile radius compared to the strength at 10 pile radii. The results also imply that the spacing of cylindrical piles should not be more than 4 to 10 times pile radius, so that the surrounding soil matrix may improve the vertical bearing capacity under any foundation or embankment loading.INTRODUCTIONThe engineering community is familiar with different techniques to improve the bearing capacity and settlement characteristics of weak cohesive and organic soils. Some of the in situ techniques to improve the properties of soft ground (e.g. soft clays) prior to placement of foundations are vertical preloading, deep cemenUlime mixing, stone columns, and grouting (Henn 1996; Moseley 1993). In addition to these methods, researchers have recently showed interest in achieving soft ground improvement by means of applying radial compression method for which different names exist including expanding pile (Kelleher et al. 2001 ), Preload™ Pier (Biringen and Edil 2003), and sand compaction pile (Lee et al. 2004). Handy (2001) has described how preloading can also be achieved by imposition of radial loading in soft ground with an expected improvement in stiffness. The idea behind the latter method is densification and consolidation of soft soil in the radial direction by controlled displacement for which the process can be viewed as a cavity expansion problem (Vesic 1972)."

Jan 1, 2005

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No.1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No.2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No.2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

May 11, 2007

By Paolo Cavalcoli, Federico Pagliacci

"As opposed to the static functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles). Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago. These are real challenges for those carrying out these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the rhetorical figure of ""David and Goliath"": cunning versus force. In reference to the case studies in this article: the permanent retaining walls for the Copenhagen Metro, and the structural repairs to the Arapuni Dam in New Zealand and the Wolf Creek Dam in the U.S., we will describe the foundations constructed in presence of rock using combined small-diameter direction drilling solutions, associated with their enlargement up to the project’s size, at depths exceeding 300 feet. Finally, a case study will be presented on the implementation of a large cross-section of an excavation in the rock, at depths greater than 800 feet.IntroductionAs opposed to the functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles).Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago.These are real challenges for those building these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the biblical figures of ""David and Goliath"": cunning versus force. In the engineering field, the force is summarized in the use of ever-larger drilling equipment in terms of installed power, weight in working conditions, winch and rotary capacity."

Jan 1, 2015

By Seiji Mizutani, Hirofumi Taguchi, Makoto Yoshida, Hidenori Takahashi, Naotoshi Shinkawa, Kazuo Konishi, Yoshiyuki Morikawa, Masaya Kawata

"The lattice-shaped cement treatment method has been used to improve the seismic performance of liquefied sandy soil in Japan. The efficacy of the method has been confirmed by the huge earthquake in Japan. In the present study, a new method to improve sandy ground by using the lattice-shaped cement treatment method is proposed as a liquefaction countermeasure. It is the floating-type and lattice-shaped cement treatment method, where cement treated soil is not fixed to an un-liquefiable stratum. In this method, a fixed-type structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were firstly conducted to confirm the mechanism of the new method. Secondly, a series of centrifuge model tests were performed to demonstrate the effect in a proto-type scale's stress condition. The analyses and model tests confirmed the effect of liquefaction countermeasure of the new method.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2015

By Michael W. Driller, Wen Yan (Grace) Chen, Steven J. Friesen

"Remediation for Perris Dam has been proposed in response to deficiencies identified in a seismic stability study prepared by the California Department of Water Resources (DWR) in 2005. Lenses of potentially liquefiable soil have been identified within the dam foundation which may lose strength during a seismic event. The remediation was designed primarily to limit deformation of the dam. Nineteen construction methods were compared and evaluated for the remediation. The final decision was to use cement deep soil mixing (CDSM) to strengthen the foundation and to construct a downstream berm to stabilize the dam. The entire CDSM treatment will cover over 4,000 linear feet of the downstream toe of the dam. Over 300,000 cubic yards of CDSM will be used to strengthen the foundation. The construction of the project started in Fall 2014 and is anticipated to take approximately 3 years. This paper describes the design aspects of using CDSM to treat the foundation, including laboratory testing, investigation of overstressing/cracking, extent of treatment, effect of CDSM on pore pressures under the dam, and the results of a full-scale CDSM test section.INTRODUCTIONPerris Dam is a zoned earthfill dam with a length of 2.2 miles, a maximum height of 128 feet, and a capacity of 131,450 acre-ft of water. The dam is located in Riverside County, California at the terminus of the East Branch of the State Water Project. The embankment was constructed between 1971 and 1973 over an alluvial deposit between the Bernasconi Hills to the South and Russell Mountains to the North. A rock outcrop divides the dam into left and right reaches when viewed from the reservoir looking downstream. The embankment soil was obtained from a borrow source at the North end of the reservoir. The dam has a sloping sandy clay core (Zone 1) with a 10-foot deep cutoff trench and a silty sand shell (Zone 2) with a downstream chimney and blanket drain (Zone 3 and Zone 4) as shown in Figure 1."

Jan 1, 2015

By Rick Deschamps

A reoccurring problem with support of excavations in urban areas involves the placement of external support components like anchors or nails in right-a-ways, subway and utility setbacks, in areas occupied by adjacent structures, and within the property of non cooperative neighbors. Such a situation occurred for a project in Arlington, Virginia, which ultimately resulted in the preliminary design of a large footing supported cantilever retaining wall that was extremely costly and impractical to build. An innovative design alternate consisting of a series of vertical concrete elements (VCEs) supported by post tensioned tiedowns was proposed to the General Contractor and accepted by the owner. The VCEs were designed to serve as the main structural elements for both the temporary support of excavation system and the permanent wall. The VCE?s were constructed using single bite diaphragm wall panels oriented perpendicular to the excavation face including a rebar cage and tremie concrete. Threaded inserts were placed within the rebar cage to attach the cast in place exterior wall. Overall stability and lateral movement of the VCEs were controlled by high capacity vertical anchors embedded within the VCE. A detailed instrumentation program was installed to monitor the movements of the VCEs with relation to the excavation depth. The paper present the project case history by discussing the design concepts of the VCE, the construction approaches used to install them, the construction challenges encountered, and the performance of the unique system.

Jan 1, 2008