Search Documents

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007

By Rick Ellman, Ian Chaney

"The Hampton Roads area encompassing the Norfolk, Virginia Beach and Newport News metropolitan region experiences some of the worst traffic congestion in Virginia. With continued growth of the ports and increasing demand, the Virginia Department of Transportation (VDOT) initiated the Downtown Tunnel/Midtown Tunnel/MLK Expressway Project, a complex undertaking critical to addressing the Hampton Roads area’s transportation needs. The project is a $2.1 billion Design/Build/Finance/Operate (DBFO) endeavor most notably involving the construction of a new two-lane vehicular tunnel utilizing the Immersed Tube Tunnel (ITT) method. The tunnel will pass under the Elizabeth River parallel to the existing Midtown Tunnel between Norfolk and Portsmouth, Va. It will be the largest design-build project constructed in the history of the Hampton Roads District.The New Midtown Tunnel will extend approximately 6,450 ft (1,966 m) along the north side of the existing tunnel where it ties into the existing Midtown Tunnel approaches in Norfolk and Portsmouth. It is being installed in a pre-excavated trench of which approximately 2,250 ft (686 m) required bracing on the Portsmouth side and approximately 1,000 ft (305 m) required bracing on the Norfolk side. The remaining 3,200 ft (975 m) of trench excavation was open cut dredging with laid back side slopes, optimized to reduce dredging, disposal and backfill quantities while also reducing the risk to the existing tunnel. The braced excavation portions of the tunnel alignment were divided into distinct segments which include: Portsmouth Approach Boat Section, Portsmouth Approach Cut-and-Cover Section, Portsmouth Dredge Section, Norfolk Dredge Section, Norfolk Approach Cut-and- Cover Section and the Norfolk Approach Boat Section. All “approach” excavations were performed in the dry and all “dredge” excavations were performed in the wet. Eleven ITT segments are being fabricated in the Sparrows Point Dry Dock facility in Baltimore, Md., and each 14,000 ton (12,700 tonne) segment is being towed approximately 220 mi (354 km) to the site. The ITT segments will extend under the Elizabeth River, with the deepest crossing 90 ft (27 m) at the Federal Navigation Channel. Once beyond the channel limits the ITT rises at an approximate 4.5% slope. Controlled screeding and element lowering operations will be performed primarily from floating barges."

Jan 1, 2014

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Michael J. Brown

Load testing is important for controlling the quality of piled foundations. The Statnamic test is an alternative to existing testing methods with a load duration that lies between that for static and dynamic tests. Current methods of analysis offer excellent correlation between static and Statnamic tests for coarse-grained soils but often over-predict the capacity for fine-grained soils. Thus a calibration chamber is being used to produce instrumented beds of clay with reproducible properties. A model pile placed in the beds can be loaded at varying rates using a computer controlled servo-hydraulic system. Results from the modelling will be used to improve methods of analysis and govern the design of a full-scale study. Initial results suggest the rate effect can be represented by a power law relating pile velocity and resistance. Statnamic loading of the model pile produced large negative pore pressures in the clay bed.

Jan 1, 2002

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Theo. A. M. Salet

The historic centre of one of the most beautiful cities in Northern Europe -Amsterdam - is being excavated to accommodate the new North/South metro line. This new line is due for completion in 2012, and will link the Buikslotermeerplein district north of the harbour, underneath the Central Station and the old city with its gables and picturesque canals, to the commercial centre in Amsterdam Zuid/WTC. Three underground stations are being construction in the old city at Rokin, Vijzelgracht and Ceintuurbaan. The logistics of working in the middle of an historic city are demanding -maintaining tram, vehicular traffic and pedestrian access along narrow streets, providing suitable protection for the public alongside the working areas, arranging adequate delivery routes, as well as monitoring the old and mostly historical buildings for potential settlement. Safety of both the public and adjacent properties is paramount. Diaphragm walling - 1.2m & 1.5m thick and up to 48m deep - was chosen as the support system for the three deep metro stations. Challenging engineering as well as state-of-the-art equipment to construct the diaphragm walls was needed in order to meet the tight working specifications, in the narrowest locations imaginable. Extreme conditions call for innovative solutions.

Jan 1, 2006

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By Jean J. Abiassi

The Boston Marine Industrial Park (BMIP) VENT 6 project is a cut and cover tunnel, part of the Central Artery / Tunnel (CA/T) in the city of Boston. The BMIP job will serve as the south approach to the Third Harbor Tunnel crossing. The alignment is approximately 2500 Ft long and is made up of four sections starting from west to east: 1. West Tunnel 2. Boat Section 3. East Tunnel 4. Tunnel inside Vent 6 Cofferdam and connection to the Third Harbor Tunnel. The support of excavation (SOE) system for the West Tunnel, Boat Section, and East Tunnel are all a part of this project whereas the SOE for Tunnel inside the Vent 6 Cofferdam was a part of the contract for the Third Harbor Tunnel.

Jan 1, 1994

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006

By Mark X. Haley

Foundation design and construction in Boston has changed dramatically during the past 10 years. Prior to 1985, the primary foundation element in Boston, where deep foundations are required, was driven end-bearing piles. Since 1985, drilled or excavated high capacity foundation elements have been utilized more frequently. This paper will provide a historic perspective of their use and a summary of design parameters for elements installed and founded in the bedrock. TOPOGRAPHY Boston was founded in 1630 by the Massachusetts Bay Company of John Winthrop and his hearty band of Puritans. The settlement was chosen for: ? its safe harbor, ? abundant source of fresh water, and ? peninsula setting offering protection of the ocean on almost all sides with high ground for fortification. These three factors were a direct result of past geologic processes that created the Boston Basin by erosion of the soft bedrock underlying this area as compared to the harder granite rock to the north, west and south. As the glacial ice sheets melted and moved northward, various soil types were deposited. During ice sheet re-advancement the hills and islands of Boston took on their precolonial shapes. The Trimont, consisting of Beacon, Mt. Vernon and Pemberton Hill, rose to 150 ft above sea level with the smaller Copps and Fort Hill to the north and south.

Jan 1, 1994

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By Frances Badelow

This paper describes a design process for piled raft foundations supporting high-rise buildings. The design process comprises an initial stage of geotechnical site characterization using the results of investigation boreholes to prepare a subsurface model and derive geotechnical parameters for raft and pile design from empirical correlations. Following this a preliminary analysis is undertaken using a combination of elastic theory and allowances for non linear behaviour of the piled raft system to assess the viability of such a foundation system and any potential advantages of a piled raft over conventional fully piled foundation systems. Finally, a detailed analysis is undertaken using the GARP8 computer program. Case studies where this design process has been successfully used to design a more efficient piled raft system that has resulted in significant cost and time savings compared to conventional bored pile foundation options are also described.

Jan 1, 2006

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007