Search Documents

By R. L. Wei

The disturbing influences of pile driving on the surrounding soil mass, including the induced vibration, pore pressure and displacement of soil, were observed during the construction of pile foundations. It is shown that the effects of pile driving in saturated soft clay are tremendous and ought to be concerned attentively.

Jan 1, 2010

By Michel Bustamante

The original Cistercian Lure abbey situated in eastern France and built in the second half of the 16th century, has become nowadays an administrative building. Because it has been founded on poor ground conditions and inadequate foundation scheme, the abbey has suffered severe structural distortion. In 1992 an inspection revealed new extensive damages which led to a general refection together with a foundation underpinning. Micropiling was the selected method. Movements recorded over a period of 6 years after underpinning completion are presented.

Jan 1, 2002

By Safwan Labanieh

An experimental set-up is specially designed to study the behavior of a friction pile of 3 cm diameter in contact with the soft clay of Mexico City in a small calibration chamber (CC) of 30 cm diameter and 50 cm height. The consolidation of this compressible clay is accomplished using a special system adapted to the CC itself to insure a good knowledge of the initial state. Loading results of the pile under a consolidation pressure of 50 kPa indicate an elastic mobilization of shear stresses at the shaft of the pile (?3 kPa for 1mm displacement) followed by a hardening plastic type behavior. Unloading-reloading results indicate a mobilization of shear stresses of the same type and of the same order of values obtained from the virgin loading stress path. Cyclic loading (?40 cycles) between 0 and 1 kPa (1/3 of the failure value) give similar results to those obtained from virgin loading.

Jan 1, 2002

By X. L. Chen

The diaphragm walling has been recently adopted in one of the largest excavation of deep foundation engineerings in Shanghai, China with dimension of 90m in length, 50m in width and 13m in depth to solve its stability problem. In this paper the field test for monitoring the stability of the diaphragm wall is discribed, in which the excess pore water pressure and the horizontal displacement of the clay layers were monitored during the period of the excavation. The data measured in the field test are efficient for the safety during construction.

Jan 1, 2010

By H. R. Taber

The extensive subject area "Engineering Practice of Ground Improvement" will be treated within the limitations of space and the writer on the basis of personal practice and experience?largely in Northern California over a period of some thirty-six years and, in "ground improvement" work, with an emphasis on transportation facilities. The stress is on improvement of ground conditions, rather than on techniques of improving inherent earth materials characteristics. "Ground improvement" is discussed as engineering resolution of existing or emergent earth materials defects or deficiencies?that is, as the technically feasible procedures best adapted to achieving a required level of service within physical, economic, social and other constraints. A "required level of service" concept is presented as a tool in evaluation of appropriate ground improvement work.

Jan 1, 2010

By Mustapha Zergoun

This paper presents the results of load tests to assess the vertical load carrying capacity of concrete expanded base piles, or pressure injected footings, for various projects located near Vancouver, British Columbia, Canada. The site subsurface conditions and load test methods are described for the Vancouver International Airport site and the test results are reviewed under both compression and tension loading conditions. The pile load tests at Vancouver International Airport are compared to load tests at other sites near Vancouver. The pile load test results are reviewed with respect to available methods of estimating the vertical capacity of this type of piles. The effect of ground improvement by densification on the load test results is considered. The limitations of tension load tests on single piles with respect to uplift resistance of pile groups under seismic conditions are pointed out. Recommendations are proposed regarding pile load test methodology to estimate ultimate vertical load carrying capacity of plies for limit state design.

Jan 1, 2004

By J. W. Slatter

Cast in situ screw piling techniques (both displacement and non displacement) have seen considerable growth in recent years due to competitive production rates, low noise and vibration free installation. However the discussion on the mechanics of auger installation, which has implications on the installation effects and installation forces of screw piling augers, has been almost exclusively targeted towards non displacement techniques and in particular continuous flight augers (CFA). This paper discusses the historical development of the understanding of screw piling auger mechanics in sands and presents a new theoretical model to predict the soil transport and displacement characteristics of both displacement and non displacement augers with variable geometry.

Jan 1, 2000

By Narong Thasnanipan

Performance of diameter 1.5 m toe-grouted bored pile founded at depth 44 m in sand-gravel formation of Chiang Mai City is presented in this paper. Toe grouting was applied by using tube-a-manchette method. Effectiveness of toe grouting was observed from the standard penetration tests conducted immediately below pile toe through grouting pipes at two stages, prior to grouting and three weeks after completion of grouting. Improvement of pile end resistance by toe-grouting is demonstrated with a series of back analyses carried out by load-transfer method employing hyperbolic transfer function. Construction experience of large diameter deep-seated bored piles in multi-layered subsoil and practical aspects of toe-grouting are also briefly discussed.

Jan 1, 2002

By Brian Littlechild

Whilst there is much innovative work being undertaken in South East Asia in the space allowed in this paper we have settled on describing in more detail the work that has been done with shaft grouting of deep foundations and piles founded in rock both in end bearing and socket friction. The paper is necessarily in two parts. The first part is about the application of shaft grouting since its introduction to the region some eight years ago. It describes, for the first time, much of the detail of the different techniques used and the construction and the design benefits achieved with shaft grouting in five countries in the region. The second part outlines the enhancements achieved in the design of piles founded in rock and brings together the results of 10 years of test loading. This includes the load testing of 1.2m to 1.5m diameter piles to a maximum of 30MN on granite and a recent programme of tests on a wide range of strong rock types in Hong Kong. The ground conditions for these deep foundations vary widely, from sedimentary soils to in situ weathered granite and meta-sedimentary rocks. The construction techniques include barrettes constructed using mill techniques and bored piles formed under bentonite and water using both oscillators and rotators.

Jan 1, 2000

By William Auyeung

Micro-piles are small-diameter, drilled and grouted reinforced piles used for both structural support and in situ earth reinforcement. They were conceived in Italy in 1952, but have become popular in Canada and the United State only since the mid-1980s. The Province of British Columbia completed a construction of a 265-km (165 miles) four-lane highway between Campbell River and Victoria in the year of 2000. The construction of Big Qualicum Bridge was part of the above mentioned provincial government project and this bridge was made of twin cast-in-place concrete parabolic arch structures. The overall length of the bridge is 261 metres (856 feet) and the width is 24.2 metres (80 feet). The massive thrust from each arch is resisted by groups of 46 drilled micro-piles that are about 230 mm (9 inches) in diameter with No. 18 high strength Dywidag threaded bars with double corrosion protection up to 15 metres (50 feet) long. This paper will describe the micro-pile design and installation methods. The performance of the micro-piles in full scale testing in tension and compression monitored with electronic strain gauges will be presented. The impact of drilling methods on the performance of the micro-piles will also be discussed.

Jan 1, 2004

By Michael D. Justason

This paper describes the technology behind the development of an automated energy control system for a diesel pile hammer. Some background is given on experience using an energy monitoring system on the Route 1/I-95 interchange in Alexandria, Virginia. An adjustable hammer throttle and feedback from an energy monitoring system was then used to create a fully automated hammer energy control system. The performance of this system is described in reference to a piling project in Canada where the automated energy control system was used to obtain an unprecedented level of quality control and assurance ? data and graphs from the project are presented. The hammer energy control system (ECS) was used to successfully control and maintain a prescribed impact energy for the diesel hammer. This paper presents the first ever results from a truly automated diesel pile hammer and points to a new direction in quality control and assurance in pile driving.

Jan 1, 2006

By Piotr D. Moncarz

As major urban areas begin to run out of "good-terrain" for their expansion, they begin to claim high water-table areas within or adjacent to water fronts or swamps. Similarly, major infrastructure projects encroach on or cross high organic content areas. The associated major structures often require deep foundations located in soils investigated through core samples removed at a discrete number of locations. The investigation is nearly always preoccupied with soil mechanical properties, sometimes with soil non-organic chemistry for concrete and metal corrosion, seldom, if ever, for organic-chemistry and bio-conditions as related to concrete longevity. Not surprisingly so, bio-corrosion of concrete is one of the least understood phenomena by practicing civil engineers. This paper shows how low-iron, organic-rich sediments may trigger sulfate degradation of concrete, even when standard pre-construction chemical analyses indicate only a moderate sulfate level. The discussion is illustrated with a case of a pile foundation in the United States driven into marine channel sediments and sediment-derived fill material. The concrete piles lost their structural integrity due to secondary ettringite formation and depletion of iron in the cement paste. Disintegration of concrete occurred only where it contacted superficial marine sediments and sediment-derived fill material. Concrete in direct contact with seawater or native sand and silt materials appeared to be sound. Sediments in contact with the degraded concrete were highly anoxic and had a history of sewage contamination, contained low concentrations of total iron (<2%), Fe(III) (<0.3%) and moderate levels of sulfate (1500ppm), and exhibited high bacterial activity. This environment resulted in the microbial dissolution of Fe(lll)-rich ferrite in hardened cement paste. Iron depletion in the cement paste had made the concrete vulnerable to degradation by sulfate, even at moderate levels of sulfate concentrations in the sediments.

Jan 1, 2002

By Jeffrey R. Hill

This paper discusses the use of micropiles for the rehabilitation of the following two structures: the Milwaukee Auditorium Theatre, in Milwaukee, Wisconsin, and the Cupples Ballpark Lofts, in St. Louis, Missouri. The paper focuses on the similarities and differences of the remediation techniques used for each structure. The discussion highlights the method of attaching the micropiles to each respective structure. Generally the paper discusses the micropile installation at each project with supporting photos, figures and data. Load testing at each project is also discussed, including the comparison of load test results for each project. The paper will focus on the load testing program at the Milwaukee Auditorium Theatre where high capacity micropiles were designed and tested as friction piles founded in stiff clays and end bearing micropiles in dolomitic limestone. The results of the test were used to determine if the micropiles on the project would be installed as end bearing or friction bearing elements. Strain gauges were used in addition to conventional deflection vs. load data for the Milwaukee Auditorium Theatre project. Other aspects of the paper will include the differences in design methodology for end bearing micropiles in massive dolomitic limestone vs. design in softer, weathered limestone.

Jan 1, 2008

"Every year during the Transportation Research Board (TRB) Annual Meeting in Washington D.C., the Federal Highway Administration (FHWA) National Geotechnical Team (NGT) takes time to talk about what we are doing in research, training development and policy support. At times, I have jokingly referred to it as the State of the Program Address, but we do see it as an important opportunity to update our transportation partners on priorities and needs for the program.This update is really a snapshot of the program during the previous year, with a look at projects that are currently active. Activities undertaken by the NGT are funded from multiyear roadmaps maintained by the FHWA program and research offices, and reflect trends and opportunities affecting and influencing transportation geotechnics now and in the future. The roadmaps identify activities in research, development, guidance, technology transfer and training that will be accomplished by the NGT through and beyond FY 2020 in eight broadly-defined focus areas: • Extreme events, geohazards and sustainable geotechnics• Performance management• Reliability-based design and construction• Advanced geotechnical modeling• Alternative delivery methods• Design and construction optimization• Site characterization• Quality assuranceThe process to identify focus areas and to develop activities that will be addressed by the NGT is guided and informed through input from the FHWA NGT members, and considers feedback and input from State Departments of Transportation (DOTs), FHWA Division offices, industry and academia. This process is revisited annually to review not only the activities that are currently funded, or will be funded, but also to review the relevance of the focus areas with respect to the future needs of the FHWA, State DOTs and the transportation community.In 2016, the NGT was successful in delivering several products that will advance the state of the practice and that better support policy. Products developed included research reports, design and construction guidance, and training courses. In 2017, the research and program offices will continue to work on projects that fit within our prioritized plan and that positively impact the geotechnical community as a whole. A listing of recently completed and currently active projects is provided below."

Jan 1, 2017

By Andrew Cushing

This paper presents the design and construction of the foundation for a major high-rise real estate development on the west side of Manhattan. Arup was retained by Underpinning and Foundation Skanska to design a secant pile wall as excavation support for a proposed two-level basement of a new 23-story residential building located at 100 11th Avenue and West 19th Street. The secant pile wall will also act as the permanent basement retaining wall for the new building. The site is bounded on two sides by existing structures and is underlain by a thick deposit of very soft organic silt and clay. Therefore, the potential for ground movements and their impact on an adjacent structure bearing on shallow footings were of the utmost concern. This paper addresses the design and construction considerations associated with this secant wall, as well as installation details. Measured wall movements are also used to assess the validity of the pre-construction soil strength and stiffness design parameters.

Jan 1, 2008

By W. Morgan NeSmith

A drilled displacement pile program was utilized for the expansion of an existing power plant in Cohasset MN adjacent to the Mississippi River. The drilled displacement (DD) pile is an innovative foundation type that provides exceptional value in some geologies. In the U.S., DD piles have typically been used in coarse-grained soils due to the large friction capacities that can be generated by the piles in these conditions. This project was the first large scale experience for the project team where it was anticipated that significant portions of the DD pile capacity would be developed in primarily fine-grained soils. The project site consisted primarily of variable amounts of fill overlying predominantly low plasticity alluvial silts. In some cases, alluvial silty sand layers were encountered within the expected pile installation depths. Alluvial sands were typically encountered below the silts, in some cases within the expected pile installation depths. The project team developed a probe and pile load test program to address the variable subsurface conditions across the site. The program included monitoring various parameters (including applied torque and tool penetration rate) during the drilling portion of the pile installation using recently developed data acquisition techniques. This data was used to estimate the rig energy, or Installation Effort (IE), required for pile installation. IE profiles from the test and indicator piles were compared with subsurface data available from a number of previous site characterizations. Additionally, Cumulative IE values were compared to an in-house database of IE vs. DD Pile Capacity. Final production pile toe levels were based primarily on IE values selected from this comparison. The IE data collected during production was also used to address large variations in pile-cutoff elevation (relative to a fairly uniform ground surface elevation).

Jan 1, 2008

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By Ernest Naesgaard

Post-grouted micro-piles were used for the seismic upgrading of the Vancouver International Airport Domestic Terminal Building (DTB). The micro-piles provided vertical resistance to both uplift and compression loads to supplement the existing timber pile foundations ability to resist the earthquake induced forces, and to provide foundation support at locations where the installation of traditional driven piles was difficult. This paper describes the site conditions, design rationale, installation method and quality control testing procedures. Site and Subsurface Conditions Vancouver International Airport is located within the central portion of Sea Island, Richmond, British Columbia (Fig. 1). Sea Island is bordered by branches of the Fraser River on the northeast and south sides and the Strait of Georgia along the west side. The natural grade of the island is part of a large delta that has been built up over several thousand years. The general pattern of sediment deposition has followed the direction of the Fraser River flow from east to west, and has built up soft sediments of about 200 m thickness at Sea Island (Luternauer, et al. 1993, Mathews and Shepard 1962). The original grade in 1962 prior to the existing Airport Terminal Building development was at about geodetic elevation 1.1 m with a grass and topsoil cover.

Jan 1, 2004

By Walter G. Brusey

This paper describes a comprehensive pile test program conducted at John F. Kennedy International Airport (JFKIA) to evaluate pile types and design capacities ranging from 890 to 4450 KN (100 to 500 tons). Driven cased piles and drilled shafts, both standard construction and post-grouted after installation, were tested with platform loads extending to 8900 KN (1,000 tons). Alternate load test procedures were developed, extensive structural integrity testing and dynamic load tests were performed on selected shafts. A brief update is provided covering the application of results of the test program to pile selection for support of major structures incorporated in the on going redevelopment of JFKIA.

Jan 1, 2000

By Aly M. Mohammad

The design of large diameter drilled shafts in weathered rock has always presented a challenge to the foundation engineers. Degree of weathering and load transfer mechanism through the rock are essential elements required for the design. From the Contractor&apos;s perspective specifying the right equipment and estimating the rate of drilling in the weathered rock are key elements for successful construction. The Delaware River Tramway Project has provided an opportunity to address the design and construction of drilled shafts in weathered rock. The Tramway, supported by twin 300-foot towers, will shuttle eight-person gondolas across the Delaware River in about four minutes. Each tower, founded on four high capacity drilled shafts, is designed to resist large axial and lateral loads. At the New Jersey tower, each 7-foot diameter shaft extends 145 feet deep and terminates in weathered Mica Schist. The shafts are situated in the Delaware River where the mud line is approximately 20 feet below Mean Low Water. Below the mud line, there exists a very soft, 20-foot thick layer of organic silt, followed by a 40-foot thick dense sand stratum. Below these sand and silt strata, a 70-foot thick layer of weathered Mica Schist underlies the entire site. Both skin friction and end bearing in the weathered rock stratum were utilized in the analysis to compute the axial capacity. AASHTO and the PennDOT design methodologies were utilized independently during design of the drilled shafts to verify the design. The drilling of large diameter drilled shafts embedded into weathered rock and situated in a marine environment provided a unique challenge in the construction. A permanent steel casing was installed for a specified depth and proper equipment was used to drill and keep the shaft open through the weathered rock. In addition, a 5000 kip Osterberg load test was performed on one shaft to verify design assumptions and confirm the shaft capacity. The results of the test were utilized to establish load transfer characteristics within the weathered rock and to develop foundation design parameters to be used for the remaining shafts.

Jan 1, 2003