Search Documents

By J. Mosher, G. Banini, J. Hollow, A. Villanueva

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

Arsenical bearing deposits are posing an increasing challenge for the mining industry. In particular, mineral processing of arsenical sulfidic ores for base and precious metals recovery tend to produce problematic arsenical tailings. This arsenic being present as sulphide or oxide, tends to dissolve, contaminating surface and underground waters. To meet the environmental regulations, it is often required to stabilize the arsenic in a more insoluble form. Dundee Sustainable Technologies has developed a new patented technology using vitrification of the arsenic oxide in an economical way, giving a stable solid, well below the environmental regulations upon leaching. This technology involves oxidation of As (III) to As (V), by using a low cost natural oxidizer and transformation of the produced arsenic oxide into calcium arsenate, which is not volatile at the melting temperature of the glass. This technology would be advantageously applied on most cases around the world where sulphide concentrates are oxidized in a fluidized bed or smelted.

Jan 1, 2014

By David Christensen

The long-term performance of dry covers is being examined in a research study funded by the International Network for Acid Prevention (INAP). The study was separated into two phases. The two main components of Phase 1 of the study were the identification and research of the processes affecting the long-term performance of dry cover systems and an examination of available numerical models for simulation of long-term cover performance. Identification and research of the physical, chemical, and biological processes affecting long-term performance showed that cover performance could be related to the change in the saturated hydraulic conductivity of cover material, the change in the soil-water characteristic curve, and the physical integrity of the cover system. Seven numerical models were examined to evaluate their effectiveness in predicting the long-term performance of cover systems. VADOSE/W (Online Help v1.01, 2002) was selected for use in cover system modeling in Phase 2 of the project. Phase 2 of the research study is currently in progress and involved the selection of five mine sites with a minimum of three years of performance monitoring data for analysis of cover performance. Two of the mine sites will be analyzed with the two-dimensional VADOSE/W numerical model. In addition, field saturated hydraulic conductivity tests were completed at three mine sites to investigate the change in field hydraulic conductivity of the cover system materials. The objective of the field testing program was to evaluate changes in hydraulic conductivity of cover material with time. Measurements of field hydraulic conductivity were completed with a Guelph permeameter and a pressure infiltrometer at three sites. The field hydraulic conductivity data was used to evaluate whether a change in this key material property had occurred over time. Field observations and the historic performance monitoring data provided the necessary information to develop hypotheses as to the likely processes that led to any change in field hydraulic conductivity. This paper will briefly summarize the research completed in Phase 1. The remainder of the paper will focus on the field testing program completed to measure the field hydraulic conductivity of constructed cover systems.

Nov 1, 2002

By Richard W. Hutchinson, Christopher Osterman

The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and footwall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fIne grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfIde piercement structures and the footwall Cu-PGE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By Miguel A. Cuba

Trends in the mean and/or variance are a longstanding challenge in mineral resource modeling. Geologic modeling and/or grade domaining are often employed to account for heterogeneities in mineral grades; however, this is only practical up to a certain point since the number of data available for reliable model construction can be severely reduced. In such cases, trends remain present in certain geologic/grade domains and directly impact the modeling methodology; the trend must either be handled explicitly or a suitable approach is adopted to implicitly account for it. This is highly dependent on understanding the source of the trend. We propose an approach that detects the source of non-stationarity, which is based on quantifying the impact of non-stationarity in the mean and the variance via the semivariogram. By expanding the methodof- moments approximation of the semivariogram, we decompose the experimental semivariogram is into three terms: 1) trend in mean component, 2) trend in variance component and 3) stationary component. We can then assess the source of trend by calculating the contribution of each component at every lag. Two cases are presented to illustrate this tool. Firstly, a synthetic reference model is simulated and different trend patterns are added; the influence of these patterns in the experimental semivariogram calculation are analyzed and discussed. Secondly, a real dataset is considered where the impact due to the presence of trends in the mean and variance are assessed. The results of this paper reveal the semivariogram to be a tremendously powerful tool in determining the source of the trend. This insight may be useful in the selection of a suitable modeling approach for resource estimation.

Oct 1, 2009

By A. Tohn, K. Adham, R. Lu, D. Lemieux

"To remove sulphur, carbon and arsenic from the gold concentrates of Dundee Sustainable Technologies (DST), Hatch has designed a demonstration plant roaster using the fluid bed technology. The fluid bed was selected for its ability to maintain stable temperatures and uniform reaction conditions. Data points from a small pilot plant (operated by DST) were used for setting the parameters of the demo plant roaster.The DST demonstration plant is being built to further prove their patented gold extraction process at an industrial scale. Their gold extraction process is based on halogenation at atmospheric pressure and relatively low temperatures. Before the halogen leaching, most of the sulphur, carbon and arsenic should be roasted out of the feed concentrate.The Hatch fluid bed roaster design includes a moist feed introduction system, simple bed cooling for temperature control, and cyclone fines recirculation. The demonstration plant roaster is planned for construction in 2014, and the performance results will be presented in a future paper."

Jan 1, 2014

By G. Tairova, J. Ioffe

Arsenic, selenium and mercury species are common contaminants in mining aqueous streams and present significant environmental and health problems. The objective of this project is to investigate methods to lower the concentrations of these elements in mining aqueous streams. A new composite media for removal of these elements of concern from mining effluents was developed. The results of bench scale and pilot plant experiments, using the media, indicated removal of arsenic, selenium, mercury and other elements of concern below detection limits.

Jan 1, 2014

By Ken G. Stowe, Stephen L. Chryssoulis, Christian Bendel, Joe Y. Kim, Ewald Niehuis

"TOF-SIMS (Time-of-flight secondary ion mass spectrometry) was used to detect collectors sorbed onto the surface of mineral particles in concentrate and tailings samples from the Brunswick, Matagami and Kidd Creek concentrators. This technique uses ion beams from either Cs or Ga sources to sputter the particle surface, a method which reduces fractionation of the collector molecule during sampling.In the Brunswick Zn circuit, sphalerite particles lost to the scavenger tails had less amyl xanthate and isobutyl xanthate compared to sphalerite recovered to the Zn final concentrate. Xanthates were detected on the surface of sphalerite particles floating to the CuPb final concentrate.At Matagami, significantly more isopropyl xanthate and isobutyl dithiophosphate were detected on sphalerite recovered to the Zn final concentrate, compared to sphalerite lost in the Zn rougher tails.In the Zn circuit of Kidd Creek, sphalerite lost to the tails had on average ten times less xanthate compared to sphalerite recovered into the Zn final concentrate. Xanthate was also detected on the floated pyrite particles. In addition to isobutyl xanthate, amyl xanthate was also detected on the floated sphalerite and pyrite particles.This preliminary investigation has (a) demonstrated the ability of TOF-SIMS to detect individual collectors on particle surfaces from plant samples and (b) shown that TOF- SIMS is an excellent tool, complimentary to TOF-LIMS, in establishing the surface chemistry of minerals as related to mineral processing."

Jan 1, 1995

By A. E. Reschke

Optimized mine planning of the Leeville Gold Mine, Nevada, necessitated the requirement for an average of 2540 tpd of high quality cemented rockfill (CRF) in primary stoping blocks and underhand cut and fill workings. To meet this requirement, a number of innovative design features were incorporated into the overall batching plant design. Foremost is the use of a dedicated skip to transfer crushed aggregate from surface down through the ventilation shaft to twin underground storage silos. Also, the use of a high shear colloidal mixer on surface to pre-slurry a cement/flyash binder with pipeline delivery to one of two separate underground CRF mixing stations was incorporated. Finally, the binder and aggregate are combined in a 9 m3 twin shaft compulsory type mixer before loading into teleram trucks for placement.

May 1, 2007

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By G. A. Barclay

"I - INTRODUCTIONSteel castings still comprise the largest volume of wear materials used in crushing and grinding in the Canadian mining industry. The range of impact and wear properties possible with steel castings enables them to be used successfully in both high impact crushing as well as milling where abrasion resistance is the main criterion. Approximately 15,000 tons per year of steel mill liners and crusher castings are used by Canadian mines.The properties of the main steel casting alloys used - manganese, pearlitic chrome-moly and martensitic medium carbon steels will be discussed with reference to their applications. Field data on a new application in primary gyratory crushers for martensitic medium carbon steels is presented. Liner wear life and mill efficiency can be improved through proper liner design.The liner wear pattern can be used as an indication for liner profile changes to improve wear life. Changes in liner configuration can improve through put and use of larger castings can reduce downtime. Casting performance can be improved and foundry production costs reduced by adopting certain design improvements.II - ALLOYS USEDTable I list the most common ferrous liner materials used in relation to their hardness and wear resistance (1). The most wear resistant materials are the irons at the top. In many applications the service impact exceeds the impact strength of the irons and tougher less wear resistant steels must be used. The impact resistance improves from top to bottom with manganese steel the toughest. The hardness of the martensitic steels approaches that of the Ni-Hards however the wear life, because of the absence of carbides, is less."

Jan 1, 1983

By D. G. Cerigo

"INTRODUCTIONAn interim report covering an uncompleted project on revenue mill optimization was presented at the invitation of Mr. C.S. Stevens, the Secretary of the Canadian Gold Metallurgists. The work described summarizes the preliminary work carried out at the Noranda Research Centre on computer mill optimization and is an attempt to arrive at a model of a circuit using the ""black box"" approach and hence by using economic factors related to concentrate dollar value to maximize revenue. The help and cooperation of Mr. J.D. Wild, Mr. M.J.S. Bennett of Noranda and Dr. A. Bobkowicz of McGill University is gratefully acknowledged.DERIVATION OF MODELHistorical data from the Normetal mill were used for the study. Normetal ore contains chalcopyrite, sphalerite, gold, silver, pyrite and pyrrhotite. For simplicity, data were chosen for days when only two concentrates had been derived, a copper concentrate which also contains the gold and silver, and a zinc concentrate. In these periods when pyrite concentrate was not produced, its circuit was used as an extra zinc scavenger unit. Figure I is a schematic drawing of the circuit and Table I explains the nomenclature.The mill had been operated to obtain a fixed grade of copper and zinc in the copper and zinc concentrates respectively, at the same time insuring acceptable recovery levels. The target grade for the copper and zinc concentrates had been derived by manual calculations based on past experience. The data used were 170 sets of daily mill reports, a sample of which is shown in Table II. The data consist of daily tonnages of feed, concentrates and tailings and their average compositions obtained by taking samples every twenty minutes from each stream and analyzing the daily composite samples."

Jan 1, 1967

By Garry Biles, Ken Major, Raj Anand

"Prime Resources Group Inc. (Prime) commenced the Eskay Creek Mine operations in 1994 in northern British Columbia. The ore from the underground mine is crushed and shipped to smelters in Japan and Canada. The nominal production rate is 300 tonnes per day.Before commencing the above operations, preliminary evaluations for the high grade gold mine had indicated that an extremely complex metallurgical and chemical process flowsheet would be required to recover the economic metals. Subsequent to the metallurgical testing program, Prime identified markets for the untreated ore and initiated underground mining and ore transportation operations.Prime recently identified lower grade ore zones, which are less economic or uneconomic to mine and ship directly to the smelters. Test programs were initiated to evaluate processes for upgrading the ore to a marketable product. In 1997, Prime will complete the engineering and construction of a 150 tonne per day flotation plant to concentrate the gold and silver values for the NEX and 109 zones. The mine will then, in addition to the direct shipping of the shippable ore, ship concentrate from the millable ore. This paper discusses the development and design of the flotation plant.IntroductionThe Eskay Creek Mine is located in north-western British Columbia approximately 83 km north-west of Stewart, B.C. as shown in the location map Figure 1. Access to the site is provided by a restricted access gravel road from Bob Quinn Lake junction of highway 37, a distance of about 59 km. The work force at the mine is based on a two-week rotation schedule. Employees are flown from as far away as Vancouver to Smithers by commercial airlines and then from Smithers to the Bob Quinn airstrip by local charter. During poor weather conditions, transportation to site is by vans that take about six hours to travel the 450 km road distance."

Jan 1, 1998

By Collin Bartlett, H. Storch

"Modern metallurgical processes operating with oxygen enriched air, such as the Outotec Flash Smelter and Flash Converter, generate very concentrated SO2 off-gas, which in combination with Outotec sulphuric acid plant technology allows the production of high pressure steam to be used for power generation. Outotec combines well proven technology of sulphur burning plants for this purpose with metallurgical plants.The application of Outotec’s proven LURECTM process enables processing of SO2 gas of up to 25 vol.-%. This process maximizes the energy recovery from the SO2 oxidation at a suitable high temperature level which can be turned into high pressure steam. The application of the Outotec HEROSTM heat recovery system enables the generation of low pressure steam from the absorption energy released at the intermediate absorption step. Additionally, energy is also recovered in the acid coolers for boiler feedwater pre-heating.The concept of integration of high and low pressure steam in combination with the pressurized operation of the boiler feedwater deaerator, thus heating up the boiler feed water to temperatures around 160…170°C, enables indirect transfer of low pressure steam (for deaerator operation) into more valuable high pressure steam, which improves the degree of heat recovery. This is the characteristic of Outotec’s HEROS+TM process.The increased generation of high pressure steam will in turn enable the generation of more electricity when compared to a standard traditional sulphuric acid process."

Jan 1, 2014

By John F. Vynne

This paper will discuss several of the systems and processes that have been developed over the past few years, and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline RSLs, and inspection and response strategies. The use of these technologies provides significant increases in dragline production, and reduces maintenance costs and downtime. The question that needs to be asked is what value is there in monitoring? Increasing dragline productivity is dependent upon to two items with the overall goal being to maximize the number of bank cubic meters moved and to uncover more coal: 1) maximizing payload and 2) maximizing the number of cycles. If you do not measure and try to optimize the parameters that impact payload and number of cycles, there is very little chance that you can improve overall dragline productivity. These parameters are: Maximizing payload is dependent upon the following: ? Geology ? Blasting ? Monitor weighing accuracy ? Engage location ? Disengage Location ? Rigging ? Suspended load ? Bucket characteristics ? Operator skills ? Minimizing rehandle Maximizing the number of cycles depends upon maximizing digging time, and minimizing cycle and delay/down times by: ? Minimizing Operational Delays ? Minimizing Mechanical Delays ? Minimizing Idle time ? Minimizing Walking time ? Minimizing Fill Time ? Minimizing Swing Angle ? Maximizing Swing & Return Rates ? Minimizing Spot Time A third reason to monitor, conduct structural analysis studies, and have inspection strategies is to prevent catastrophic failures such as shown in the following photographs (figures 1 & 2).

May 1, 2008

By H. J. Hartjens

"With the trend towards bringing into production ore bodies of lower and lower copper content every possible avenue of approach to achieve maximum copper metal recovery and keep milling costs to a minimum are of increasing importance.Equipment manufacturers have contributed a great deal by designing larger mills, flotation machines, pumps, etc. in lowering capital and operating costs; instrumentation and automation usually as a joint effort of operating staffs and equipment manufacturers have resulted in lower operating costs and improved metallurgy. Likewise manufacturers of chemicals used in mineral beneficiation have directed their research and development at new flotation reagents and treatment schemes to complement the needs for more efficient products, permitting coarser grinds without detriment to recovery, higher flotation rates, higher degrees of selectivity, as well as chemicals to improve settling, clarification and filtration. The various treatment schemes in use and suggested for consideration are:1) The choice of the flotation treatment scheme is largely dictated by the desire to operate a simple circuit, originally consisting of rougher and scavenger flotation, with scavenger concentrate either returning to the head of the rougher circuit or joining the rougher concentrate for cleaning by reflotation, with and without prior regrinding. The cleaner tailing was also recycled to the head of the rougher circuit. In the case of porphyry copper ores, this was originally the standard circuit. Lime is the preferred alkalinity regulator to adjust pH, usually in the range 10-12.To avoid the undesirable effects of circulating loads and gain the advantage of simplified control of the rougher circuit, open circuit cleaning is practiced more and more. In this scheme, cleaner tailing is scavenged to produce a discardable tailing and the scavenger concentrate returned either to the cleaner or the regrind circuit."

Jan 1, 1970

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

By D. Embury

The construction and utilization of oil and gas pipelines is a vital aspect of the Canadian economy. The evolution of materials for this application can be considered as part of an evolutionary process in which the processing of the materials is linked to the design requirements of the pipeline. The evolution of both materials and designs will be considered in terms of parameters such as yield strength, work hardening characteristics including strain path changes such as the Bauschinger Effect and toughness. The final portion of the presentation will consider the possible uses of non-metallic materials, composites and 'smart 'systems in pipeline construction.

Jan 1, 2005

By A. L. Mular

"On behalf of Bob Bruce and myself I would like to begin by stressing some key points.First, most of us know that the Canadian Mineral Processors was formed in 1969 and is an offshoot of the Canadian Gold Metallurgists. I attended that first meeting in 1969, and I haven't missed a meeting since! Pretty obvious that CMP serves the best booze! At any rate, we know that our meetings are supported by CANMET. Camsell Hall is always at our disposal; Bob Bruce acts as permanent secretary pretty much free of charge; we receive a financial grant from CANMET. This brings me to a second point.Second the Canadian Mineral Processors do not enjoy a free ride in this relationship. CMP provides a genuine service to the mining industry, to government, and to universities. For the industry, CMP serves as a forum for the rapid dissemination of new ideas and new technology developed at remote locations throughout Canada. New developments outside Canada are introduced by invited speakers at our meetings. The effect is to help reduce operating costs and increase efficiency.For government, problem areas and research priorities can be isolated through mutual discussions. Direct communication at our meetings can help CANMET to temper its goals and modify its national priorities.For universities, CMP provides a wealth of operating experience and practical know how. The yearly proceedings are a major current reference source fo1· those of us who teach mineral processing. Admittedly, the proceedings are publ-shed from CMP coffers. However, I note that our fees are up this year, which brings me to a third point.Third, we face some potential problems of a financial and political nature. From a financial view, we may lose our CANMET grant and other financial good will simply because of spending constraints. Our fees are expected to climb each year thereafter.From a political view, we know that the metallurgical society of CIM is anxious to incorporate CMP as a section. The pros and cons of such a merger have been described in a recent mailing. In th2 final analysis, the political and financial problems are interrelated. There are several alternative solutions to both problems, which brings me to a fourth point"

Jan 1, 1979

By J. Koponen, K. S. Stadler, A. Fuerst, S. Gaulocher, Th. von Hoff, R. Veldsman

"Gearless mill drives (GMDs) are the workhorse in the mineral processing industries, more specifically when it comes to grinding crushed ore and cement (in various production stages) in semiautogenous (SAG) mills and large ball mills. They are renowned for their excellent reliability and robustness, long lifespan, and little need for maintenance, and thus yield a low total cost of ownership (TCO).A GMD represents a major investment for a mineral processing plant, and its availability is pivotal for the grinding process. As a basic rule, shut-down periods are to be minimized, but even much more important is that unscheduled shut-downs be avoided. In this contribution, we will present a portfolio of innovative remote diagnostic that consist of the following three key components:1. Trouble shooting is a form of corrective maintenance and is based on state-of-the art remote access technology, thus enabling highly skilled engineers to access the current sensor readings anytime and from anywhere in order to resolve urgent problems together with the GMD user.2. Periodic maintenance reports are a form of preventive and predictive maintenance and aim at continuous improvement based on long-term historical records and analyses of multiple measured signals. These detailed reports highlight the health and operational status of the GMD and are periodically (e.g. 3 months) submitted to the customer.3. Remote condition monitoring spans across preventive and predictive maintenance and is based on continuous recording and automatic analyses of relevant signals using advanced algorithms. The main issue is how to handle the enormous flood of data in an intelligent manner. The results of these analyses are made available to both the GMD user and supplier in real time in order to increase the availability and reliability of the GMD.In this paper, we consider various parts of the GMD, e.g. the cycloconverter, the ring motor, the auxiliary devices (e.g. cooling and lubrication systems), and also phenomena related to the mill itself (e.g. state and quantity of charge). The signal analysis techniques range from simple threshold-based analyses to complex time and frequency domain analyses. We will illustrate the benefits of the proposed approaches with some selected examples."

Jan 1, 2012