Search Documents

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level indicated can be in considerable error, largely because of variations in froth and collection zone bulk densities. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the collection and froth zone. This probe detects the position of the interface to an accuracy of ± 5 cm. The probe can be used while the column is in operation, which allows for on-line recalibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 m in diameter) are described.

Jan 1, 1990

By Bryan Tisch

Goal of GMGE ??To advance mine reclamation through the beneficial use of organic residuals for the sustainable establishment of bioenergy crops and other productive land uses Objectives ??To advance the current ?standard? of mine reclamation by demonstrating that mining lands can safely become agriculturally ?productive? through the use of organic residuals. ??To generate and compile sound scientific data that can be utilized by stakeholders to better assess the environmental impacts of utilizing these materials. ??To complete a manual of best practices regarding the utilization of organic residuals on mine lands. *Considerable effort to be placed on operations/implementation side of utilizing residuals ?rather than just pure research

May 1, 2011

By D. H. Wilson

"This paper examines the increasing need for mechanical-electrical people within the industry and some of the reasons why such a shortfall exists. It is suggested that, in part, it is image related. The present industry-education relationship in addressing the situation is examined and some thoughts are expressed on how these may be built on, in order to help solve the problem of attracting people to this critical area.IntroductionAs a long-time proponent of plant engineering and maintenance as a management function, I would like to review the progress made by the industry/ educational approaches in satisfying the needs in that area. In doing so, I would like to make the following points:1) that there has been an accelerating shortfall of mechanical-electrical people relative to the needs of the industry;2) that the condition will probably get worse before it gets better; ,3) that the past industry I educational approaches to alleviate the problem have met with limited success; and finally4) I would like to review some of the things being done and consider how these efforts might be extended."

Jan 1, 1981

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By Dieter Birk

"The Atlantic Coal Institute illustrates the potential for high technology employment in Maritime Canada, by using local talent and the latest equipment to address a national market. Since I983, contract research for industry and government has generated 31 man-years of high-tech employment, added $2.3 million to the local economy and contributed new technology for Canadian coal. Industry now has access to new procedures for coal minerals analysis, pyrolysis, and geochemistry applied to industrial problems of exploration, beneficiation, conversion and combustion.Research at the Institute is market-driven, based on cost recoveries from contracts. The financial performance to date exceeds that of similar industrial research institutes in major cities and demonstrates that small isolated laboratories are cost-effective. Economic renewal of Canada's resource industries will require increased R&D which in turn can be a source of local employment and pride. Small research teams are more efficient but require an enlightened policy of contracting-out by big business and big government."

Jan 1, 1987

By Robert B. Parsons

"There is a widespread concern that certain of Finance Minister Michael Wilson's Tax Reform proposals will likely lead to a significant decline in flow through funding after 1988. This does not bode well for the junior exploration sector, which relies heavily on flow-through to finance exploration programs. The exploration industry is actively pursuing various solutions to the problems posed by Tax Reform, in order to ensure that flow-through has a future.IntroductionWhile the proposals contained in Finance Minister Michael Wilson's Tax Reform White Paper may not be as far-reaching as some people had expected, nevertheless the combination of the existing tax rules and proposed new rules offers sufficient complexity to keep pencils sharpened for many months. After having had an opportunity to study Tax Reform since June 18, 1987, the sharpened pencils are suggesting that the White Paper is not without its shortcomings and pitfalls. Insofar as the mineral exploration industry is affected, there is widespread concern that adoption of certain Tax Reform proposals could spell near disaster for mineral exploration in Canada. More specifically, there seems to be a consensus among the industry, as well as some federal and provincial government officials, that the announced phase-out of the ""mining exploration depletion allowance"" (MEDA) would reduce the appeal of flow-through shares to the point where only a fraction of exploration funding would be financed in the future by flow-through."

Jan 1, 1987

By G. Ladouceur

"Northgate Patino Mines produces a copper concentrate assaying 22% Cu. Moisture content of the product averages 12.5% H20 when dewatering with conventional vacuum disk filters. Recent smelter contracts reflect higher energy costs and increased moisutre penalty charges. This situation forced Northgate to investigate possible alternatives such as rotary dryers and pressure filtration. After laboratory testing, it was found that pressure filtration could economically meet the smelter's requirements. Pilot plant testing was then undertaken and confirmed the laboratory test results. Based on these findings, a model I.S.F. 1500 x 28/22 I.R. Lasta filter press was purchased.This paper describes the Copper Rand dewatering flowsheet the operation of the press and the economics of the process.IntroductionNorthgate Patino Inc. operates 2 und erground copper mines and a 3300 ton per day concentrator located in Chibougamau, Quebec, some 425 miles north of Montreal and 300 miles northeast of Noranda, Quebec.Copper concentrate is produced at a rate of 250 tons per day and trucked to a C.N. siding 10 miles from the mill site and then railed to the Noranda Smelter.Until early 1981, moisture content of the concentrate at 12.5070 was acceptable since smelter penalty charges were relatively low ($0.10 per ton per unit over 10070 moisutre). In January 1981, a new contract was signed in which the penalty was raised to $1.10 per ton per unit over 8070 . This and the increasing truck and rail costs justified the change-over from vacuum to pressure filtration . The Lasta I.S .F. 1500 x 28/22 was then purchased and installed, and operation of the plant started in December 1981."

Jan 1, 1987

By Peter N. Calder

Long range mine planning involves developing a mining sequence that schedules the extraction of the ore and waste materials within a final pit limit. The objective is to define a sequence that best meets the defined strategic objectives. The main steps in the creation of an open pit mine plan are the final pit limit design, the design and sequencing of the mining phases, equipment selection and operating cost estimation. Flexibility is the key strategic element in developing a mine plan. Planning the extraction sequences and rates for the various mining areas is a challenging and demanding activity. It is often necessary to consider numerous alternative strategies and what if scenarios. The number of alternatives that can be studied with limited manpower and time resources is restricted. In order to investigate strategic aspects of mine planning, a system to generate workable mine plans rapidly is required. The concept of Visual Mine Planning is that the engineer can visualize the current plan, easily change a component of the plan, such as the annual cut-off grade schedule or the production rate within a particular Phase, and immediately see the effect on the mineralogical and cash flows. If the desired result is not achieved, a change is made and the effect is again immediately seen. This paper presents results of research in this area conducted at the Pontificia Universidad Católica de Chile. The work includes the examination of cut-off grade strategy, sequencing, blending, stockpiling and shovel-truck fleet requirements using simulation.

May 1, 2003

By T. L. Carpenter

"The presence of excessive water in the Gibraltar East Stage 1 pit initiated studies into the ground-water conditions that might be expected in mining the Granite Lake and Pollyanna pits. Hydrologic information obtained from a pump test program in 1974 indicated that deep-well dewatering could be successfully achieved. In 1976, a deep-well dewatering system consisting of eight wells was installed on the periphery of the Pollyanna pit . it has been responsible for a significant decrease in mining costs.This paper presents a brief summary of the engineering principles involved in the design of the Gibraltar dewatering system and the problems encountered in the installation and operation of deep-well pumps. IntroductionGibraltar Mines is an open-pit copper-molybdenite mine located approximately 230 air miles north of Vancouver in the central interior of British Columbia (Fig. I). The property consists of three separate major orebodies; Gibraltar East, Granite Lake and Pollyanna (Fig. 2). Mining commenced during the summer of 1971, in the Gibraltar East Stage 1 pit. The Granite Lake Stage 1 pit was mined from mid 1974 to mid 1976. The Pollyanna Stage 1 pit is currently being mined and the Gibraltar East Stage 2 is being developed for production. This report is intended as an outline of the studies and tests leading up to and including the installation of the Pollyanna pit dewatering system, the problems encountered and the results obtained.GeneralIn the summer of 1973, mining in the Gibraltar East pit progressed below ""daylight"" on the down-hill side and ground water very quickly became a costly nuisance in the day-to-day mining operations. Mining, maintenance and blasting costs reflected these problems. Concern was also voiced about adverse effects of ground water on pit wall stability. This concern later became a reality in the Gibraltar East and Granite Lake pits. A study was initiated to investigate various methods and costs of dewatering the pit areas. The study included in-pit sumps, deep peripheral wells and a drainage gallery system located below the pits."

Jan 1, 1980

By Denni Nikols

"Planning for coal beneficiation in the electric utility industry is relatively complex, involving the coordination of experts and specialists in a broad range of fields, as well as compliance with a wide variety of government regulations.This paper examines the role of the planner, reviews possible benefits of coal beneficiation, identifies potential problems and illustrates a typical planning schedule.The steps involved in the planning process are:Step I-Bench- and pilot- washability studyStep 2- Wash plant designStep 3- Power plant and boiler designStep 4-Mine designStep 5-Major environmental and technical problems to address.IntroductionElectrical utilities and coal have a long and intimate relationship . Cleaned coal is becoming an increasingly popular fuel with the utilities for a variety of reasons. Generally, the greatest impetus to burn a cleaned or prepared coal fuel comes from the need to control airborne pollutants.Long-range planning is a standard practice for electric utilities, forecasts of demand must be made well into the future. Since the lead time required to provide new facilities is often as long as 10 years and the cost very high , planning becomes an important task.For a utility that owns and directs the operation of its coal mines, the mine planning or fuel acquisition planning takes on the magnitude of other corporate planning functions. It is from this perspective that a utility would view coal preparation. Except for the interaction of a coal-fi red plant on the actual mine design the planning considerations o f a beneficiating facility for a captive mine or a contract raw coal supply are about the same. Because TransAlta Utilities is currently supplied from captive mines, this discussion will tend to focus in that direction.It is the role of a planner to plan. This is easy to say but it is not always easy to do. Often we are working within a context that resembles the geological time scale. Frequently the objectives are not clearly defined when we begin and ultimately our plans are tested in the waters of government regulations and cost benefit analyses .Planning for beneficiation of Plains coal, or any coal, provides just such a test. The planner's role in this endeavour requires a wide vision. While parts of the process may be amenable to classical methods of project scheduling, the broad range of subjects and interaction of seemingly unrelated tasks is sure to obscure some of the considerations that must be made. Therefore, the planner's chief role is coordinating the work of many experts and specialists toward the final objective.Among the specialists are combustion , geo technical, mining, civil , and mineral processing engineers , geologists, hydrogeologists, soil, and reclamation experts to list a few.When one considers coal beneficiation, the planning part o f that consideration is probably more complex than any other single engineering function. Due to the company's location in the Alberta Plains and the proximity o f the mine to the thermal generating station, this paper will tend to emphasize that situation.Beneficiation may offer some advantages over run-of-mine coal to the power plant opeator. Some of these advantages are: removal of a contaminant, power plant efficiency gains , lower plant capital costs (for new plants), possible lower mining costs."

Jan 1, 1984

By P. R. A. Andrews

"Talc ore from Bakertalc, High water, Quebec analyzing about 60% talc, previously dry ground to about 95% minus 53 µm was beneficiated in an 11.4 kg/ h pilot-plant flotation circuit. A concentrate of 95.9% talc (necessary for paper-grade) was obtained at a recovery at 75.3% by employing 53 g/t of Dowfroth 250 collector at pH 9.2; further cleaning increased the grade to 97.2% talc at a recovery of 57.5%.Flotation of fresh ground 60% minus 44 µm ore at a feed rate of 18.6 kg/ h produced a grade of 96.4% talc with a recovery of 78.2%, using Aerofroth 70 collector a six carbon-branch chain alcohol, at pH 9.2.The similarity in the concentrate grade and recovery between pre-ground and fresh-ground ore indicated that it was not neces¬sary to grind to 95% minus 53/2m to achieve comparable selectivity. A grind of 60% minus 44 pm corresponds to 100% minus 300 µm.Flotation retention times obtained with fresh ground ore indicate 33 min. for combined rougher/scavenger, and 15 min. each for the first and second cleaners.Talc-magnesite flotation separation is explained in terms of physico-chemical forces, with reference to surface charge and adsorption mechanisms."

Jan 1, 1989

By Steven Chung

Decision Network Modelling in a mining operation represents a complex process environment that is inherently more variable than a processing plant or factory. The uncertain availability of loading locations, haulage paths, loading and hauling equipment, along with inconsistent operator behaviour, cause a relatively large number of upset events that must be recognized, communicated and dealt with by the appropriate management authority. Traditional process maps that represent a deterministic model of the mining process can quickly break down in the face of such a volatile environment. An alternate modelling strategy, composed of decision networks, focuses on the interactions between goal-oriented entities and their environment, allowing system integrators to explicitly determine the information to be exchanged while providing feedback mechanisms that improve system flexibility and decision quality. This ensures a consistent framework for incrementally increasing system automation.

May 1, 2010

By M. Loan

The Zinifex's Hobart Smelter uses the paragoethite process to remove dissolved Fe(III) from concentrated zinc leach liquors. This produces a residue consisting primarily of 6-line ferrihydrite (a hydrated Fe(III) oxyhydroxide), several insoluble components derived from the calcined zinc concentrate neutralization agent and other precipitated phases, such as jarosite and silica. The precipitation of 6-line ferrihydrite in the paragoethite process was studied using a laboratory-scale continuous crystallizer, and the conditions were selected to limit high levels of dissolved silica and jarosite. This approach allowed the reactor pH and the rate of precipitation to be correlated with residue solid-liquid separation, particle size, morphology, residual zinc and sulfate concentrations, and phase formation (e.g., goethite, jarosite, schwertmannite, and 2- and 6-line ferrihydrite). These studies delineated the mechanism of 6-line ferrihydrite precipitation in the kinetically controlled paragoethite process, and its inter-relationship with goethite and jarosite precipitation under conditions where 6-line ferrihydrite is favoured. Unexpectedly, the generation of a more crystalline goethite precipitate with larger "primary" particle size did not produce a residue of improved properties, as bulk aggregates dictate the physical properties of the residue and not the crystallinity. Furthermore, it is difficult to precipitate 2-line ferrihydrite or schwertmannite under existing paragoethite process conditions.

Jan 1, 2006

By J. F. Hazzard, R. J. Chalaturnyk, C. Khazaei

"Various measurement, monitoring and verification (MMV) techniques are used to ensure the safety of operations in petroleum projects. One of these techniques is microseismic (MS) monitoring of the caprock. A challenge in MS monitoring of caprock is that unlike projects such as tunnelling in hard rocks, the number of recorded events are much smaller and also wide spread through the rock mass which makes interpretation of the physical meaning behind the events very difficult.In this paper, a numerical technique is introduced and validated for coupling a finite difference code, FLAC3D (Fast Lagrangian Analysis of Continua), with a discrete element code, PFC3D (Particle Flow Code). Then, a similar approach is adopted for modeling microseismic events in the caprock. For this purpose, the underburden, reservoir and overburden layers are modeled by FLAC3D. A rather small section of caprock above the reservoir is nulled in the FLAC3D model and substituted by a PFC3D inclusion. The reservoir pressures are then applied to the reservoir section of FLAC3D. Once the FLAC3D cycles, there will be induced pressures in the caprock due to its undrained response to the change in pressures within the reservoir. These induced pressures are transferred to PFC3D as boundary velocities. Then the PFC3D cycles and sends back the boundary forces to FLAC3D. This back and forth process continues until equilibrium is reached. During this process, there will be bond breakages within the PFC3D inclusion that can be regarded as MS events. An algorithm for recording the microseismic energies based on a change in local strains is also implemented. The results are then compared with real data. The effect of injection fluid temperature is also studied. No significant appearance of microseismic events was observed due to injection of CO2 in both cases (i.e. with or without considering temperature). However, this continuum/discontinuum approach seems promising for understanding the microseismic response of caprock in more detail and also using the MS data for validation of geomechanical models."

Jan 1, 2015

By Michel Masse

1. A battery-powered wireless mesh network for dynamic diesel machinery tracking and operating status monitoring. 2. A real-time ventilation model and fan speed optimizer. 3. An OPC server for information interchange. 4. OPC linkage to existing control infrastructure. 5. A Human Machine Interface (HMI) providing data archiving, trending and reporting. 6. Live MS-Excel to interrogate the simulation, controls and optimizer. 7. The battery-powered network mesh also provides SCADA functionality to route optimized setpointsto the fans and automated regulators not linked to PLCs.

Feb 1, 2008

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

By Paul Johnston

or is it? Mining Automated Loader Technology Application ? Intelligent software mounted in hardware on a remotely controlled scoop. ? Led by INCO, Sudbury, with ? C-CORE, St. John?s ? Automated Mining Systems, Aurora ? Bell Canada, Sudbury ? Laurentian University, Sudbury ? University of Western Ontario, London Completed: March 2000

May 1, 2008

"Process specifications for classification system design f or closed circuit grinding are identified. A computer-assisted, mass balance procedure for estimation of material size distributions and required hydrocyclone separation performance is presented.GeneralClassification equipment application involves a large number of variables, but can be greatly simplified by consideration of the following two major steps:(A) Process analysis, in which the so lids and liquid material balances and solids size distributions in the three classifier streams are determined in order to establish the required classifier separation performance.(B) Equipment selection, in which the cyclone dimensions and feed conditions are selected to yield the de sired separation, and the number of units then determined by their capacity rating."

Jan 1, 1984