Search Documents

By S. Kelebek

Efficient separation of minerals is the essence of mineral processing. Separation of hexagonal pyrrhotite in processing of Ni-Cu sulphide ores was investigated together with particle size effects with respect to selective flotation recovery of pentlandite and nickel. The recovery by size response was compared for sodium metabisulphite (SMBS), triethylenetetramine (TETA) and their combinations with amyl xanthate as a collector. The pyrrhotite recovery for all sizes was lower than that of pentlandite for the blank case as well as individual cases with SMBS and TETA. For pyrrhotite, the recovery by size relations in the case of individual uses of reagents were mainly determined by recovery losses at coarser size range (>74 um), which occurs at a coarser size for pentlandite (>212 um). The combined use of SMBS and TETA, and the associated synergistic effect very significantly knocked down the pyrrhotite recovery to less than 7% that was a maximum for the –10 um (attributable to hydraulic entrainment). High recovery of pentlandite in a wide range of intermediate sizes and drastically low recovery of pyrrhotite resulted in a very efficient separation of pentlandite from pyrrhotite in all sizes. Separation of this mineral is discussed in relation to fundamental functionality of the reagents used.

Jan 1, 2017

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By A. B. C. Stothart

"IntroductionIn the past four years Ontario Mines have made great progress in the development of reliable mine conveyance safety dogs. History shows that, prior to 1945, a rope failure on a descending conveyance was usually followed by unsatisfactory safety dog operation.It is proposed in this paper to discuss briefly;The history of this development. Progressive .development of one type (E. Long).Free fall testing of safety dogs. Anti-trailing rope device.HistoryOn February 2nd., 1945, a hoisting rope broke at the Paymaster mine. The safety dogs proved ineffective and permitted the cage to crash through to the bottom of the shaft, with disastrous results.Following this accident, the Ontario Government appointed a Technical Committee to investigate The Safety of Hoisting Equipment and Hoisting Practice in Ontario Mines. This Committee consisted of Dr. C. R. Young (Chairman) and Professors T. R. Loudon, E. A. Allcut, V. G. Smith, and Lloyd M. Pidgeon. The Ontario Mining Association (at the request of the Ontario Government) also appointed a Committee consisting of Messrs. R. E. Dye, R. D. Parker, and R. L. Healy."

Jan 1, 1950

By D. W. R. George, J. L. Stewart

Developments in the last decade, which have contributed to increased productivity and decreased coke rates in the iron blast furnace, are reviewed. Future progress in blast-furnace practice is also considered.

Jan 1, 1966

By M. J. Collins

The Advocate Mines Limited asbestos property is 6 km north of Baie Ve rte on the northeast coast of Newfoundland. Mining began in the early 1960s and was concluded in 1981. The chrysotile asbestos deposit lies at the north end of the Baie Verte Lineament, the interface between a closing ocean floor and continental margin. Asbestos occurs within ultramafic rocks of abducted ophiolite massifs that were thrust westward against Fleur-de-Lys Supergroup metasediments (continental rise sediments) in the Lower to Middle Ordovician. The asbestos-bearing ultramafics belong to the Central Ultrabasic Sequence of the Advocate Complex. Serpentinized peridotite of this sequence has a 'waste cap' core that grades outward to increasingly sheared rock. Asbestos is found mainly in a northtrending, basin-shaped zone surrounding the core, specifically within fractured serpentinized peridotite that abuts the sheared rock. Asbestos appears as stockworks of chrysotile cross fibre veins and is concentrated between brown, narrow brucitic dunite dykes and sills. Shear contacts commonly surround the ultrabasic body. Cross faults and complex Jointing also exist. The Advocate Mines Limited mill produced 65,000 tonnes of Group IV fibres and 1 l , 000 tonnes of Group VJ fibres annually. The bagged product enjoyed markets worldwide.

Jan 1, 1984

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By A. Brown

"The mining industry is no exception to the general rule that continuing research is essential to good management; in fact, because of the imperfect state of knowledge in regard to many important factors associated with a mineral extraction, mining research assumes a position of unusual importance. On the basis of a recent visit to mining research centres in a number of European countries, the author describes their organization and their role in the mining industries of these countries. Some observations are made on Canadian mining research efforts, with a view to indicating a more systematic basis of procedure."

Jan 1, 1960

By M. J. Latva-Kokko, T. J. Riihimäki

"Oxidation autoclaves are normally operated at elevated temperature and pressure. The improvement in kinetics is due to combined effect of temperature and partial pressure of oxygen. In this paper exclusive effect of pressure has been studied with a low grade sulphide ore at below 100 °C temperature. These studies are related to development of a novel tower-like reactor that utilizes hydrostatic pressure. Technology is designed to generate high amount of effective fluid volume for high solid content slurries with lower energy consumption and improved kinetics compared to normal atmospheric operation.INTRODUCTIONEconomical utilization of low-grade ores requires handling of enormous amount of material. This sets new requirements for process equipment in terms of size and energy efficiency. For example on the field of mineral processing this has lead to a six fold increase in the operating volume of mechanical flotation cells over the past two decades. Ore beneficiation methods like flotation greatly reduce amount of material that needs to be further processed in smelters or hydrometallurgical refineries. However with some ore types, such as nickel laterites and refractory gold ores, traditional concentration technologies cannot be utilized. Thus direct leaching of ground ore could be an attractive option. In many cases normal atmospheric tank leaching has traditionally been a non-feasible option mainly due to high capital and operational expenses induced by large amount of stirred reactors required. Main restriction for increasing reactor size to beyond 500 m3 has been mechanical load and power requirements set by mixing in cases when high dispersion efficiency of gas is required. THEORETICAL BACKGROUNDIn hydrometallurgical industry autoclaves are typically operated at elevated temperature and pressure. In many cases increase in operating temperature is the desired phenomena and improvements in kinetics are strongly related to that. Thus increase in pressure might be induced solely by water vapor pressure. However when gaseous feed is present, pressure itself has a strong effect on leaching kinetics for various reasons and its role should not be neglected."

Jan 1, 2012

By L. E. Puddington, A. L. Mular

"Since the inception of spherical agglomeration, few investigations to exploit commercially the technique in the metallurgical field have been conducted. Of these, none appear to have been carried sufficiently far to demonstrate commercial feasibility.This paper describes a continuous agglomeration-separation process that can rapidly handle large tonnages of ore material. A small pilot plant de-signed from information obtained with the semi-batch unit described herein is currently in operation.In the absence of a reagent recovery system or cheap reagents, the process is probably not economically attractive for many common ores. However, for iron ores, the fuel content of the agglomerates can be used in a subsequent step such as direct reduction."

Jan 1, 1968

By J. C. Rudolph

"THE TOPIC on which I am speaking this afternoon is ""The Future of the Canadian Oil Industry.'' At the time of C + 100, we should take a searching look at ourselves, an honest appraisal of our achievements and a forthright accounting of our shortcomings as well as the uniquely Canadian aspects of this industry. I would like to put before you some of my views on the direction we are taking in the exploration field and in the production field. I would also like to speak briefly on some of our problems and the role of the various segments of our industry in solving these problems.First of all, let us look at the exploration picture. We are in the midst of an exploration boom. There were 133 seismic crews active in Western Canada this winter, the highest since 1957, land prices are appreciating rapidly, Canadian oil reserves increased + 16 per cent during 1966, there is a great demand for technical personnel of every kind and the whole industry, except the drilling segment, seems to be prospering. This surge of activity has its roots in two major occurrences. The first of these was the change in the pro-ration system in Alberta, the major producing province, accompanied by the change in spacing pat-terns. The proration change was designed primarily to encourage in-creased exploration and it has certainly had this effect. It has also had the unforeseen effect of put-ting everyone into what we, in the oil business, call ""elephant hunting."" In other words, the days of the development of barely economic, marginal fields are over. Oil companies today are only interested in high-reserve, high-productivity, high-quality reservoirs."

Jan 1, 1968

By N. Shi, T. G. Joseph

ABSTRACT One-twentieth-scale field trials for conventional and concept dipper designs were compared to mid- and ultra-class-sized conventional dipper performance. Digging effort was used as the performance indicator for comparison. It was shown that linear relationships exist between dipper capacity, suspended hoist load, and peak hoist load. A ratio of conventional and concept dipper performance at the 1/20th scale was then evaluated to allow prediction of the performance of an ultra-class concept design using an independent ultra-class conventional dipper dataset. The outcome indicated a peak hoist requirement of 15.5% less to achieve the same production as the conventional design.

Jan 1, 2011

By Thomas H. Heine

"The Rabbit Lake uranium deposit is located at 58° 11’00”N.. 103°42'36""W., close to the west side of Wollaston Lake, and approximately 800 km north of Saskatoon. The orebody is hosted by Aphebian Wollaston Group rocks, initially deposited as a series of shallow-water marine sediments consisting, in part, of carbonates and possible saliferous petites. Metamorphism during the Hudsonian Orogeny, peaking at about 1850 Ma, recrystallized the sediments to upper amphibolite grade paragneisses. This was accompanied by partial anatexis. The waning stages of Hudsonian orogenesis appear to be marked by minor granitic intrusive activity.The post-Hudsonian period was marked by a long interval of physical and chemical erosion, resulting in the unroofing of the Wollaston metamorphic complex. The entire region underwent extensive lateritic weathering under tropical to subtropical conditions. Carbonates were especially vulnerable and, in the Rabbit Lake area, suffered extensive solutioning with accompanying formation of collapse breccias. Old zones of weakness also underwent periodic reactivation.It was during this period that uranium was leached from the surrounding meta-sediments by oxidizing meteoric waters, and transported into the karsted and fractured rocks of the Rabbit Lake doline.Athabasca Group sediments eventually covered the deposit, their diagenesis taking place at about 200 °C and 900 bars. This allowed the partial to complete recrystallization of the initial mineralization, resulting in a minimum age of 1281 ± 11 Major ""first""-generation pitchblende. Periodic fault/fracture reactivation modified the hydrologic regime within the deposit, resulting in episodic mobilization and recrystallization of pitchblende and other uraniferous species. This is clearly shown in the open pit at the present time: uranium is being mobilized and recrystallized on damp pit walls as bayleyite and liebigite due to the modification of the hydrologic system by mining activities.The uranium mineralization occurs mainly as fracture fillings, coatings, and impregnations within breccia zones and intensely altered metasediments. Lesser mineralization is intimately associated with phyllosilicates which form the matrix of a carbonate-col/apse mega-breccia. The primary ore mineral is pitchblende, consisting of five generations, and from which a large suite of secondary uraniferous minerals have formed. On a gross scale the metal content of this deposit appears to be simple, consisting almost exclusively of U, but minor Ni, As, Cu, Se, Fe and Co are also present. The eastern limit of the mineralization is defined by a vertically-dipping microgranite dyke - breccia complex, containing high-grade uranium values. The orebody is truncated to the west and at depth by the Rabbit Lake reverse fault. Minor mineralization occurs as fracture fillings in unaltered plagioclasite in the footwall of the ore body. Precipitation of uranium from solution could have taken place by a number of processes. A mobile reductant (methane, carbon dioxide, etc.) may have been generated from graphite present in some of the host rocks of the orebody. Sulphides are also a common accessory and may have aided in the formation of a reducing environment. Phyllosilicates may have acted as adsorbants for uranium, allowing for its fixation. This metal has also been incorporated into the phyllosilicates themselves."

Jan 1, 1986

By C. H. Bucknam

Net carbonate value (NCV) characterization methods for acid generation potential measurement originated from studies on the Carlin Trend during the 1990's and have been subsequently standardized through cooperation of the Acid Drainage Technology Initiative Metal Mining Sector and the American Society of Testing and Materials International. The paper describes the evolution and standardization of the NCV methods, the importance of mineralogy in interpreting the results and application of the methods to implementation of the Global Acid Rock Drainage (GARD) Guide.

Jan 1, 2011

By A. Ignatieff

"A practical picture of the effects of stress and of the structural environment in an extraction area in a bedded deposit is described, and the main factors of ground control where principles of rock mechanics can be applied are discussed. Reference is made to early work in Europe, where systematic rock mechanics studies started in coal mines, as well as to the early work in the Canadian coal mines.During the past two decades, considerable theoretical and experimental knowledge, pursued both in the laboratory and in the field, has accumulated throughout the world, but the state of the science still does not permit application of substantiated theory such as is found in the design of above-ground structures, largely because of the complexity of the rocks. The mining engineer, as oppm1ed to the civil engineer, is constantly faced by exposures of new ground that is often subject to unpredictable discontinuities. However, the rationale already developed by rock mechanics principles and experimentation provides concepts and information that may be useful in selecting mining layouts. These concepts and existing measuring techniques can also assist ground control as mining progresses.Many of the bedded deposits, much as coals and evaporites, have pronounced deformation properties, and there are limitations in making stress measurements within short distances of mine openings or extraction areas. On the other hand, the measurement of movement of the hanging wall (roof) and footwall (floor) of roadways and extraction faces, as well as the sides of pillars, provides a most useful tool in assessing ground stability.This paper is to be regarded as a brief progress report with particular reference to Canadian applications of rock mechanics to bedded deposits."

Jan 1, 1968

By G. W. H. Norman

INTEREST in the mineral possibilities (gold, copper) of northern Quebec, north of the Quebec-Cochrane branch of the Canadian National railway, has centred for many years in the Chibougamau district (see Figure 1). Since 1934, however, promising gold discoveries in the Rose Lake-Florence River section, 115 miles southwest of Chibougamau lake, have widened the interest, and prospectors have examined other parts of the country between Chibougamau lake and Bell river and the surrounding districts. The object of this paper is to !resent an outline of the geology, and to describe the mineral deposits, o part of this region, or, more specifically, of the part embraced by the Opawica-Chibougamau and Waswanipi map-areas(l), which include the districts about Chibougamau lake and Rose lake-Florence river, where mineral deposits are now in course of development either by surface or underground work. Early discoveries, developments, and explorations in the Chibougamau district are well summarized in the report of the Chibougamau Commission, published in 1911(2). The Commission discredited previous optimistic accounts of mineral discoveries in the area, made initially in 1903, but at the same time they expressed the opinion that, from a geological standpoint, the district promised a reward to diligent and intelligent prospecting. Their general conclusion-that prospecting in the area was not then (1911) commercially advisable in view of its inaccessibility and other handicaps shifted interest from the district until, some years later, valuable discoveries were made in the Rouyn area, and aircraft widened the field of successful exploration. During the past ten years or so, considerable energy has been spent in promoting the development of the district. The net result has been the discovery of a number of prospects, the majority of which have been explored only by trenching and, in most cases, diamond drilling.

Jan 1, 1936

By A. Brown

The swift decline of coal during the period of unprecedented expansion in the Canadian economy is a phenomenon deserving careful examination, because the underlying forces contributing to this decline may have broader implications in our national economy. At the present level of technology, coal is more difficult to process, transport and utilize than liquid and gaseous fuels. Fundamentally, it is a matter of limitation in technique. Because coal is a vast store-house of energy in Canada, the reduction of these limitations is in the long-term national interest.

Jan 1, 1967

By T. S. Smith, C. C. Rennie

"THE LEAD-ZINC and tungsten mines of Canadian Exploration Ltd are on Iron Mountain, 8 miles south of Salmo, B.C., in the Nelson mining division. Relative location of the mines is shown on the general plan.First recorded lead production was in 1908 from surface outcrops. Small amounts of high lead ore were mined intermittently until 1926. No major lead-zinc production occurred until 1949 when outcroppings on the south side of the mountain were mined and diamond drilling began to prove the existence of a large replacement orebody. Lead-zinc ore has been mined continuously from the Jersey orebodies since March 1949, with monthly tonnage as high as 50,000 tons per month, but currently averaging 30,000 tons per month.Schee1ite-bearing tungsten ore was found in 1942 by H. Lakes in an old adit and open cuts at the north end of the Emerald tungsten orebody. The Emerald tungsten mine was developed by the Federal Government as a Wartime Metals project and operated for eight weeks in the fall of 1943, when the poor demand for tungsten closed the mine. Canadian Exploration Ltd. purchased the mine in 1947 and mined in excess of 100,000 tons in 1947-48 until the demand for tungsten dropped again and interest was centred on lead-zinc. The Federal Government repurchased and reopened the Emerald Mine in 195 L and built a new concentrator. The mine and mill were sold back to Canadian Exploration Ltd. in 1952.Regional Geology and IntrusivesThe host rock for both the lead-zinc and tungsten mineralization is the Laib formation of Lower Cambrian age, which consists of 400 feet of crystalline limestone underlain by beds of argillite, and argillaceous limestone locally altered to ""skarn"" or ""tactite"". The Laib limestone is overlain by black argillite and underlain by the Reno quartzite of Pre- cambrian age. Repetition of folded beds has allowed the interpretation of the large isoclinal fold which repeats the limestone (see general cross-section). Dolomitization and the associated lead-zinc ore have been found only in the right-side-up limestone and are not known in the overturned limestone.Two elongated stocks of granite cut the sediments. The Emerald stock outcrops along the east side of the Emerald tungsten mine and again west of the Jersey workings, while the Dodger stock outcrops only at the north end of the Iron Mountain. The shape and attitude of these bodies are believed to have been governed partly by pre-granite faulting and partly by pre-granite folding of the sediments. Although some forceful intrusion may have occurred the detailed granite surface indicates a gentle stoping emplacement."

Jan 1, 1949

By C. McLachlan, J. R. Donald

"Positioned at the forefront of the seafloor minerals industry, DeepGreen Resources is on track to becoming a leading producer of base and strategic metals obtained from vast high-grade seafloor polymetallic nodule deposits. DeepGreen believes the seafloor minerals industry is an opportunity for developing a more environmentally and societally attractive way to produce cleaner base and strategic metals. Polymetallic nodules contain nickel, manganese, copper, cobalt and other base and strategic metals. Polymetallic nodules represent an exceptional multi-metal-bearing resource, and no current metallurgical operation or flowsheet exists that can recover the primary metallic values while managing the distinct mineralogy. DeepGreen Resources is developing a new process to maximize the business outcomes consistent with the highest environmental standards, including targeting a near zero waste facility. The present paper discusses the history, context and driving forces of polymetallic nodule project development. An overview of DeepGreen?s Nauru Ocean Resources Inc. (NORI) project is presented along with a literature review of polymetallic nodule processing and the on-shore project development scope and plan at DeepGreen Resources is outlined.INTRODUCTION AND CONTEXT Polymetallic Nodules in the Clarion-Clipperton Zone Containing nickel, cobalt, copper and manganese, polymetallic nodules occur in most oceans of the world. The nodules lie on the seafloor sediment. The largest deposit in terms of nodule abundance and metal concentration occurs in the Clarion-Clipperton Zone (CCZ) on vast abyssal plains at a depth of 4,000 to 6,000 metres. The CCZ is located almost entirely in international waters as presented in Figure 1. It has been estimated that the CCZ contains (International Seabed Authority, 2010): •,>21 billion tonnes of nodules; •,>270 million tonnes of nickel; •,>6 billion tonnes of manganese; •,>234 million tonnes of copper; •,>46 million tonnes of cobalt. There are several active hypotheses for the mechanism of formation of the nodules including precipitation, hydrothermal decomposition of basaltic debris, and involvement of microorganisms. Nodules require a nucleus to start forming, which could be a piece of pumice, a shark tooth, old nodule piece, basalt debris or even microfossils like radiolaria and foraminifera. Nodules form concentrically with layers of iron and manganese hydroxides around a core. Although composed mainly of Mn, Fe, silicates and hydroxides, it is the significant content of Ni, Cu, Co, Zn and Rare Earth Elements (REE) that is generating the economic interest in harvesting these deposits. Nodules vary in size from micro-nodules to about 20 cm, the common size being two to eight centimeters. A typical polymetallic nodule and polished cross-section is presented in Figure 2."

Jan 1, 2017

By C. V. Deutsch, O. Babak, J. G. Manchuk

High levels of geological heterogeneity occurring over relatively short distances pose a challenge to the unconventional open-pit techniques used in oil sands mining. There is strong motivation to mine selectively and minimize dilution and loss; however, the large equipment and high mining rate used to meet production targets tend to reduce selectivity. A numerical model is developed to account for geological complexity, mining equipment, regulatory criteria, and other operational parameters. This framework is used for more accurate forecasts, optimization of equipment, and other operational decisions. An example demonstrates the approach in light of Alberta Energy Regulator criteria.

Jan 1, 2014

"The ventilation-related risks from mines with elemental sulphur include dust explosions, spontaneous combustion with emission of heat and toxic sulphur dioxide or hydrogen sulphide gases, reactions with nitrates, corrosion, acid water, and pyrophoric reactions with naked iron or other metals. Elemental sulphur will form explosive mixtures in air at lower dust concentrations and at lower ignition temperatures than coal or sulphide dusts. Potential controls include primary ventilation circuit design, control of dust deposition and static discharges, enclosing steel surfaces, inert stone dusting, FRAS ducting, humidifying the air, alternate stench gas, self-contained self-rescuers with goggles, careful siting of underground infrastructure, controls on explosives formulations and procedures, mining method selection, controls on surface temperatures and protection of equipment, careful materials selection for ventilation seals and changes to worker clothing and training.INTRODUCTIONSulphur (“Brimstone” in biblical times) is one of the world’s most important industrial feedstocks and is used in a wide range of chemical processes and industries. Until the early 20th Century, most of the world’s production of sulphur came from ‘conventional’ underground mines in Sicily (Demetra produzioni, 2006; Bellia, 2006). This was a hazardous activity. The Frasch solution mining process replaced traditional underground mining of sulphur until the late 20th Century. Most of the world’s production of elemental sulphur is now as a by-product from sour gas produced in petroleum refineries and natural gas installations (Anon, 1993). As such, there is considerable experience in understanding and managing the hazards of elemental sulphur in chemical plants and surface transport.Whilst rare, underground mines with high elemental sulphur contents (as a gangue mineral) create an unusual range of mine design and operational issues, including many ventilation-related ones. The key hazards from elemental sulphur include: primary and secondary elemental sulphur dust explosions, fires and burning (with emission of heat and sulphur dioxide or hydrogen sulphide gas), reactions with nitrates used in explosives, corrosion of steel and other metals, generation of acid water (especially at higher water temperatures), and pyrophoric reactions with naked iron (e.g., ground support, ladderways or underground fixed plant) or other metals including silver and copper (e.g., used in electrical components and equipment)."

Jan 1, 2019