Search Documents

By R. S. Jones

"Fording Coal Ltd. is now in its fifth year of a 15-year contract to supply 3 million long tons of clean coal per annum to its Japanese steel-making customers. The mine employs both conventional truck-shovel and unconventional ""walking"" dragline coal mining techniques in multiple-seam pits. This paper describes the present and future application of the 60-cu.-yd dragline and truck-shovel pre-stripping fleet in 1•ecovering 5- to 40-footthick coal seams in mountainous terrain. Deep blastholes, coal flow demands, spring ""run-off"", seam and inter-seam thrust faulting, limited seam outcrop data and regional faulting are a few of the problems encountered in this application. The author discusses these problems and their solutions as applied at Fording Coal Ltd."

Jan 1, 1976

By T. Majcherczyk

Shaft lining reinforcing analysis of two shafts under construction has been presented in this study. The first shaft was driven from the surface, while the second was deepened. Mining and geological conditions have been studied with respect to the lining capacity. The improvement of shaft stability comprised two elements, i.e. reinforcement of the shaft lining capacity and improvement of the strength properties of the rock mass. In both tested cases, the particular hazard was connected with non uniform loadings of the lining, which could generate shearing stresses within lining structure. Thus such elements as armored concrete with high strength properties, bolting and injection sealing of the rock mass, and the use of special ring reinforcing the shaft lining have been used in order to reinforce the shaft-rock mass system. Practical conclusions related with new technological solutions, allowing the rock mass and shaft lining reinforcement, have been included for the present study. Practical conclusions related with new technological solutions, allowing for rock mass and shaft lining reinforcement, have been also included to the present study.

Aug 1, 2013

By M. Pfeifer, M. N. Brodie, D. J. Barratt

"This paper reviews design trends related to the various SAG mill configuration and drive options available today. The impact of these options on capital and operating costs is assessed, and key technical issues reviewed. The discussion is based on the conventional North American ’pancake’ mill configuration. IntroductionDuring the past decade mill technology has evolved significantly in the following key areas:• improvements in variable speed motors continue with on-going advances in electronics;• ring motors, or gearless drives, are becoming more common in mill sizes 32 ft and larger, with ratings of 10 000 HP and greater;• geared drives have become available up to ratings of 9500 HP per pinion, compared to the earlier 6000 HP guideline;• improvements in speed reducer technology due to the use of carburized and ground precision gearing, make the high speed motor-speed reducer drive more competitive with the direct coupled low speed motor drive;• a unique speed reducer drive is being introduced to this industry which combines ring gear drive pinions with speed reduction. mprovement in gear alignment is claimed, and the overall drive arrangement is more compact than is possible with a conventional speed reducer drive;• the first 38 ft and 40 ft diameter mills have been designed and manufactured; and • application of large multi-shoe bearings have made shell supported mill configurations available for all, including the largest sizes. These designs have flat instead of conical mill shell ends, and have the potential for technical and cost advantages compared to conventional trunnion supported designs.This proliferation of mill design features provides several options to those involved in planning and design of milling plants, and requires more extensive evaluation to optimize mill design features to best suit specific project requirements."

Jan 1, 1999

By M. Girard, E. Bourricaudy, M. Ashbury, M. Canizares, A. Mezei

Liquid-solid separation and slurry handleability relate directly to commercial plant ramp-up success or lack thereof. The paper provides a well-proven approach for testing, scale-up and commercial application of difficult processes. Emphasis is placed on practical applications of rheological concepts developed both academically and empirically. The cause-effect relationship between the process chemistry and possible physical implications on the metallurgical plant operability is presented in a simple, direct form. Examples include recent results in areas of mineral processing and extractive metallurgy. Technical process risk factors and their mitigation are included in the discussion.

Jan 1, 2011

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019

By F. T. Rabbitts

Introduction When the investigation of radioactive ores began at the Mines Branch about five years ago it was at once evident that improved chemical methods for the determination of uranium were essential. The published methods available were time-consuming and insensitive and were lacking in accuracy and precision. It was desirable to obtain methods which would be rapid, sensitive, and accurate. They should also allow for the possible presence of any interfering elements and should be adaptable to routine analysis by technicians. Chemical methods are necessary to provide standard analysed samples for counting and to check analyses by counter methods. Moreover, counter methods cannot be used, and only chemical methods are suitable, when the sample is not in equilibrium, as with weathered minerals and leach residues. As leaching processes are improved, more sensitive chemical methods are required for the increasingly lower content of uranium in the leached residues. When the leaching process reaches the plant stage, speed of analysis becomes more important, without sacrificing accuracy. The purpose of this paper is to describe briefly .the methods used at the Mines Branch for the chemical analysis of uranium in ores. These methods represent the results of investigations by a number of groups in the United Kingdom, the United States, and Canada.

Jan 1, 1952

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By W. J. Dick

THE purpose of this paper is to point out, briefly, the importance of the coal mining industry of Alberta and to stress the economic factors that hinder its development; also to offer suggestions relating to the major problems of the industry. The minor problems will not be dealt with in detail, because, if the major problems are taken care of, it is felt that the industry itself can take care of ,he remainder. COAL MINING NO LESS IMPORTANT THAN GOLO MINING The large increase in metal mining development in all provinces of Canada, excepting Saskatchewan, Alberta, and the Maritimes, has had the effect of focussing public attention on this branch of the industry. The fact, also, that this development came at a time of depression has been of immense benefit to Canada as a whole. On account of the necessity and consequent demand for gold, with its attendant increase in price, through government action, from $20.67 per ounce to $35.00 per ounce, it is safe to say that the public of Canada have become, today, gold mining conscious. While everyone admits the great value. of the gold mrn111g industry, nevertheless, the equal value to Canada of certain other industries must not be lost sight of. The coal mining industry, in particular, is worthy of greater public and government support than has been accorded it in the past. It would seem unnecessary to stress this matter to a meeting of the Canadian Institute of Mining and Metallurgy, but unless certain facts are brought to your attention, there is danger that the coal mining industry will not be developed to the extent its national importance deserves. Too many public men and men in authority are unaware of the value of coal mining.

Jan 1, 1936

By R. L. Brown, E. A. Swanson

THE Buchans ore bodies are located in central Newfoundland, three miles north of Red Indian lake. The townsite of Buchans was named after a Royal Navy Captain who, while attempting to make contact with the Beothuck Indians, camped in the area in 1820. Ore was first found at Buchans by a Mic Mac Indian, Matty Mitchell, who discovered one of the three small orebodies in the bed of the Buchans river. The Anglo-Newfoundland Development Company, which holds mineral rights in the area, developed the orebody, but was forced to give up the venture because of difficulties encountered in separating the various sulphides. The American Smelting and Re-fining Company developed a flotation process which was capable of economically separating and concentrating the various sulphides, and, in 1926, they took a long-term lease on the property.

Jan 1, 1962

By F. Crundwell, N. Steenekamp

"The leaching of sulphide minerals generates a significant amount of energy. There are three systems that might be used to remove this energy. These are: cooling coils, quench water, and flash recycle. Flash recycle is the recycling of slurry from the autoclave to the feed tank. Heat is removed in this arrangement when the slurry at elevated temperature and pressure is flashed to atmosphere, releasing steam. The slurry is returned to the autoclave at lower temperature, resulting in cooling. The cooling is directly proportional to the steam released from the recycled slurry. Design equations and results for the flash recycle system are presented. A fourth proposal for removing heat is to recycle slurry from the back of the autoclave. These four alternatives not only remove the heat, but also have an effect on the leaching efficiency. Amongst the four alternatives, design calculations indicate that the flash recycle option is the optimal solution in terms of leaching efficiency and heat removal, and recycling product from the back of the autoclave is the worst. In spite of its efficiency in terms of heat removal and leaching, the implementation of the flash recycle system is limited to a few operations in the platinum industry.INTRODUCTIONIn considering ways to improve leaching operations, focus is placed on the chemistry, on the kinetics, the agitation and perhaps even on the gas mass transfer conditions. Attention is less frequently placed on the removal of energy from these reactors and how this might limit performance.The pressure leaching of sulphides releases a significant amount of heat. For example, the reaction for the leaching of chalcocite, Cu2S, given by"

Jan 1, 2012

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By N. Schmalbein, L. von Ketelhodt, L. Kotelo

"The mining industry continues to remain challenged. Lower commodity prices, increasing labor costs and more importantly diminishing reserves are amongst some of the primary factors contributing to the difficulties faced. Ore sorting technologies have demonstrated their potential to improve the downstream beneficiation performance. The general processing route sees all primary crushed material milled for liberation and then processed in accordance with characteristics of the gold therein, i.e.: refractory golds would require direct leaching or oxidation whilst free gold would follow the conventional cyanidation process, after gravity concentration. Ore dilution increases the associated operating costs within each stage of this process. The opportunity to process the same throughput at a higher grade can only be achieved through pre-concentration. Sensor based sorting has been examined on numerous occasions by various gold producers. Test work carried out on different bulk low grade gold ores has shown the successful applicability of ore sorting to remove waste, whilst maintaining high recovery rates of gold. The results of a combined XRT/Laser sensor sorter have shown grade improvements of over 300% from feed grades of 0,25g/t to 1,15g/t at gold recoveries of 66% and waste ejection rates of 85%. This paper presents some of the results from the work undertaken by STEINERT with respect to gold sulphide ore sorting and presents a modelled financial scenario, which can enable a company to target and reclaim low grade ores.INTRODUCTION The mining and minerals processing industry presents with many different challenges including, volatile commodity prices, increasing labor costs and more importantly diminishing reserves. Conventional processing routes will continue to play a crucial role in the beneficiation process, however innovative methods of reducing operating costs and optimizing on the overall circuit performance is where technologies such as sensor based sorting come into the fore. Sensor based sorting as a dry mechanical process not only reduces water consumption by eliminating unnecessary waste but also reduces the requirements for reagents in the downstream processes. Sensor based sorting under dry conditions presents a highly efficient alternative to wet pre-concentration methods such as dense medium separation (DMS)."

Jan 1, 2017

By A Walker

The presence of high noise levels in many industries, together with the fact that countries are becoming increasingly concerned with the health of its citizens, has contributed to the importance of the problem of hearing loss. This problem has become the focus of scientific research, law and medicine, and the object of this thesis is to present the means whereby noise may be detected, with its resulting effects and possible means of control, in mining operations. 0BJECTIONABLE noise is a particularly prevalent by-product of the mining industry, and, al-though a dangerous noise level has been recognized, it is believed that at no time now, or in the future, will it be possible to enumerate a single over-all decibel figure at which hearing impairment will oc-cur. Individual susceptibility must be recognized in any study of occupational loss of hearing aimed at the setting of standards and criteria for industrial noise control.

Jan 1, 1963

By Ben Habermann

"The object of the work described in this paper was to increase the understanding of the relation that capillary pressure of a rock, hydro-dynamics, and accumulation of oil in stratigraphie traps have to one an-other. The hydrodynamic oil-water tilt equation is derived by considering the two vector gradients involved: (1) buoyancy of oil in water and (2) hydraulic gradient.Recent theories show the necessity for oil to have a continuons phase in the reservoir rock in order to mi-grate; this fact applies to hydro-static as well as to hydrodynamic conditions. Hydrostatically, the displacement pressure of the rock deter-mines the amount of oil that can be trapped behind a permeability barrier. If the buoyancy of oil in water exceeds the displacement pressure, oil will migrate up-dip; an oil trap will be formed where displacement pressure is greater.In stratigraphie traps the pressure drop caused by moving water is positive when its direction is down-dip, helping accumulation; and it is negative when its direction is up-dip, forcing the oil into the tighter section of the reservoir. Theoretically, pro-vided we have data such as: (1) the displacement pressure of an up-dip permeability pinchout, (2) density difference between the oil and water in place, and (3) the direction and magnitude of the hydrodynamic gradient (if any), the possible extent of a stratigraphie oil accumulation down-dip can be predicted.To test the above theory sample cores from three wells in the Denver Basin were analyzed and the oil column that could be held under hydro-static conditions was calculated. After the hydrodynamic influence was considered, the results were compared with actual field data.The significant fact shown by this investigation is that the calculated oil column in one reservoir very closely approximates the actual extent of the oil column in a well. Also in accordance with the theory, the capillary pressure caused by the buoyancy of the oil column exceeded the measured displacement pressure on core samples from another productive field. For very tight shaly sand and questionable oil shows, the interpretation of data is very critical, as shown by experiments on core samples from a third field."

Jan 1, 1960

By K. G. Baxter, D. G. Dixon

The Sepon process plant utilises an autoclave to oxidize a flotation concentrate containing pyrite, residual copper minerals, and sulphur. The concentrate is produced from the residue of a preceding atmospheric copper leaching circuit. The function of the autoclave is to provide iron and acid for that atmospheric copper leaching circuit. The key issues in the operation of the autoclave are to maximise the production of acid and ferric ions and to avoid scaling issues related to sulphur balling in the autoclave. Scale control in the autoclave was examined using various dispersants and residue recycle without success. Operation of the autoclave at high temperature and high acidity addressed the scale issue through rapid oxidation of the sulphur and produced a ferric sulphate precipitate in the residue that could be re-leached to provide ferric iron. This paper presents the development steps followed, through batch and continuous piloting that resulted in an autoclave circuit design that addressed the above process requirements. Following definition of the process design basis, modelling of the autoclave operation was carried out to assist with engineering design. The model included thermodynamics and kinetics of oxidation of pyrite, elemental sulphur and covellite and also considered gas/liquid mixing, oxygen solubility as a function of temperature and solution composition, ferrous to ferric oxidation, gangue reactions with acid and precipitation/re-dissolution of basic ferric sulphate and alunite.

Jan 1, 2004

By J. Convey, S. L. Gertsman

"THE EXPANSION of steel capacity is seldom spectacular. It may be for this reason that the remarkable progress made in Canada has not been generally recognized. In 1950, Canada's output of steel ingots amounted to 3,270,000 tons ( l ), which is a ll8 per cent increase over the tonnage produced in 1939. It can therefore be readily seen that Canada's growth curve for steel production is climbing at a rate paralleling her growth as a nation. It is by no means •an exaggeration of its importance to consider the steel industry as the cornerstone in the economic structure of Canada's manufacturing activities. From the humble diaper pin to the giant members of massive bridges, fortifications, and other steel structures, steel accompanies us as a necessary and inescapable companion in our journey through life. The Age of Steel has a literal meaning, and refinements in the manufacture of the products of steel are adapting it to more and more varied uses as time passes.The integrated iron and steel works of Canada fall into two natural geographical divisions. One has its base on the Great Lakes and draws its supply of •coal and some of its ore from the United States. In this division lie the works of the Algoma Steel Corporation, at Sault Ste. Marie, at the junction point of lakes Huron, Superior, and Michigan; and the works of The Steel Company of Canada, at Hamilton, on lake Ontario."

Jan 1, 1952

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on 'The Mechanism of the Surface Phenomena of Flotation', showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By T. W. Wlodek

In this paper the relative merits of shot peening, induction surface hardening, spiral-rolling, and the combination of these surface treatments, are evaluated on the basis of their capacity to increase the fatigue strength of drill steel. The S-N relations for plain car-bon steel (SAE 1080) and Ni-Cr-Mo drill steels in the as-rolled condition were determined previously, using the new Canadian method of testing drill steel introduced at the annual meeting of the Institute in Toronto in 1950 (19). S-N curves have now been determined by this method for these two drill steels in the following conditions: shot-peened and drawn, induction hardened, induction hardened and shot-peened, and spiral-rolled. ( S.R.) . The ratios of the fatigue strengths of these steels after surface treatment, to their fatigue strengths in the as-rolled condition, are compared and the most beneficial treatments are thereby pointed out. The expected range of stresses and their distribution during actual drilling operations are estimated from data available, and the mechanism of failure of drill steel in the as-rolled and surface-treated conditions is analyzed. The magnitude of the surface compression stresses and their effect on ?fatigue strength are discussed.

Jan 1, 1958

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973