Search Documents

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By P Corbett, P Sheffield

Centennial Coal operates the Springvale longwall mining operation which extracts coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale, and the neighbouring Angus Place mine, have a history of difficult geotechnical conditions where combinations of a relatively high stress regime and weak, laminated roof and extensive geological faulting has led to numerous roof failures throughout the mine’s life. Following development, the mines underground roadways can experience high levels of roof movement which may lead to roof falls. Multipoint wire extensometers are extensively used throughout the mine for roadway condition monitoring, and to reactively drive remedial strata support through trigger action response plans (TARPs).As a result of the use of high-density extensometer monitoring over a long period, the mines have an extensive archive of legacy data. Data processing has evolved over time in order to accommodate the increasing data volume, including direct data entry from the recently introduced hard-wired real-time monitoring instruments. It is likely that telemetric real-time instruments will be introduced in the future, which will cause another step change in data management requirements. This paper discusses the transition to and evolution of relational database management systems for extensometer and associated data.This paper also presents case studies of the use of a new software tool for reprocessing legacy data to enable time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. The software can be used proactively in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological and geotechnical data to allow correlation of monitoring data results with risk factors.CITATION:Corbett, P and Sheffield, P, 2015. The use of high-intensity monitoring data to better characterise geotechnical properties of a non-homogeneous rock mass, in Proceedings Third International Future Mining Conference, pp 145–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By J Nortier, J Dray

There is no single factor that determines the appropriate capacity for a mining project. It is driven by the size of the resource, the capacity of the market, the availability of capital, the availability of power, the availability of water, and a myriad of other considerations. There is also no single solution to the question of how big the project should be. However, to develop a project, the study team needs to select the configuration options that it regards as the best for the project. To be able to make this selection, the study team should consider the range of available options and do so at a level of detail that gives it confidence in the conclusion but does not lead to multiple detailed design exercises. Having considered the range of options, and with a clear definition of the project owner’s objectives and constraints, the work to be carried into feasibility studies can be focused appropriately. This paper discusses the process of completing strategic mine planning to identify project configuration options to assist in the selection of the processing plant throughput rate (Capacity Study) for a large greenfield open pit mine. The processes described in this paper allow for the basis of design to be set for subsequent studies that meets the objectives at a risk profile acceptable to the owner.

Jun 22, 2022

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

By C Dell

Hillgrove, situated on the New England plateau of New South Wales, is an area rich in history and resources. Key resources are predominantly antimony, gold and scheelite and the area surrounding the historical field is environmentally sensitive and topographically challenging. Since acquiring the Hillgrove leases, Straits Hillgrove Gold has undertaken a significant exploration program on these historical mining areas with the goal to return the field to production. This exploration program has enabled Straits to significantly increase the resource base and has subsequently enabled the planned redevelopment of Hillgrove to be realised. In October 2006, installation of mining infrastructure and the initial stripping of existing development had commenced. To successfully redevelop Hillgrove, Straits has had to adopt a highly mechanised, trackless, diesel mining operation which will see the production rate commence at an initial rate of 250 kt/a of ore from a narrow vein environment. This ore will be processed on site to produce antimony metal, gold bullion and a scheelite concentrate.

Jan 1, 2008

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By S Lehane, S Pearce

The characterisation and assessment of waste rock has been the subject of considerable research, and many guidance documents have been published both internationally and within Australia. While these documents provide detailed information on how to characterise waste rock, there is not a great amount of detail on how to determine the optimal waste management options from an operational viewpoint. For example, typical questions that a mine operator would seek answers to include: What placement method should be used (eg end tipping versus paddock dumping)? What is an optimal tip head height for waste placement in a storage facility? How should sulfide grade control be carried out?Defining the contributing factors to waste management and waste material placement and assessing the contribution of each variable directs these assessments towards a semi-qualitative and quantitative methodology. Quantitative methodologies show an increase in the confidence of these assessments by providing logical, measureable assessments.As part of a strategic assessment for waste management at an active mine site, a detailed risk-based investigation of the influence of variables common to waste placement was completed. These variables included placement method, placement height, sulfur grade and material conditioning (eg compaction) on the associated risks of waste material storage. The assessed risks include temperature assessments (potential for thermal take-off as a result of spontaneous combustion), toxic gas production and flow and acid production potential. Applying a numerical modelling approach to the assessment of the different waste material placement strategies allows for the variation in risk to be graphically presented and communicated through risk matrices and histograms.CITATION:Pearce, S and Lehane, S, 2015. Quantitative risk assessment tools to assist with waste management and placement guidelines, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 353–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S R. Green, G D. Corder

The legacy issues from mining can, and have often, extended well beyond the closure of operations. However, conventional cost-benefit analysis provides little incentive to implement initiatives at the project development stages of a new mining project as the costs that will be incurred towards the end of the mine life, 20 years or longer, appear minor in net present value (NPV) terms. This analysis can be misleading as the true costs of managing post-mining land can continue for many years, or decades, after mining ceases and any resulting unfavourable legacy issues can delay or prevent government permits or licences to develop new resources. Proper upfront planning is critical for implementing successful rehabilitation and closure strategies. The investment in this planning needs to be done in a structured and rigorous manner taking into consideration the long-term and broad benefits of sustainable land uses after mine closure. The advantages of such an approach could include the streamlining of regulatory approvals by early advice to the regulator of identified issues and responses to those issues, and clear evidence that a strong social licence to operate ethic with local, regional and national benefits is included in the decision-making process. This paper investigates the potential closure options for two case studies at the early stages of project development - concept and prefeasibility. By using a sustainability framework that can identify opportunities and risks, prospective initiatives that deliver enhanced environmental, community and social benefits will be compared with compliance-orientated approaches. This comparison is made across the Five Capitals Sustainability Model - natural, human, social, manufactured and financial. The results of this analysis demonstrate that upfront planning during project development and due care and effort during the life of the working mine will reduce the risks of long-term detrimental legacy issues. This will ultimately benefit the mine operator, the local community and the state.CITATION:Corder, G D and Green, S R, 2012. Using a sustainability assessment framework to achieve enhanced legacy outcomes, in Proceedings Life-of-Mine 2012 , pp 311-318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C Hamilton

Stawell Gold Mines (SGM) is an underground mining operation located in Victoria, Australia. The mining method employed is long hole retreat stoping, utilising up and downholes and artificial concrete pillars. Stawell is currently mining the Golden Gift and Magdala orebodies.Access to the Magdala and Golden Gift deposits is via 6.0 m wide by 5.5 m high declines developed at a gradient of one in eight to one in seven from the surface to a depth of 1500 m, with a planned depth of 1650 m. From the declines, cross cutting drives are developed to intersect the orebodies. Orebodies in the Gift system are discrete lodes which are generally mined from a bottom up centre retreat to minimise geotechnical stresses.Ore development fronts are currently located between 1000 m and 1500 m below surface, with all ore being hauled to the surface using a fleet of 60 tonne underground trucks. With the use of conventional pyrotechnic long period (LP) delays, broken rock of combined ore and waste is thrown 10 m from the face and the materials hauled to the surface. The majority of the mullock from development is consumed in the underground as backfill.With the use of Orica Mining Services eDev™ Electronic Blasting System for Tunnelling, the waste is thrown up to 40 m from the face, while majority of the ore is left 5 - 10 m from the face, effectively segregating ore and waste. This enables significant recovery of gold values with minimal loss and significantly reduced dilution. By using this technique in ore drives with a 30:70 waste to ore ratio, SGM is able to haul 24 000 tonnes less mullock to the surface annually. Resue mining is applied to narrow vein headings and gives a 40 per cent grade increase at the faces as well as increasing the economic footprint of development. This will also contribute to an improved grade profile for the year from 3.98 - 4.16 g/t Au and allow extra capacity for ore haulage from stoping and for milling.This paper describes the application and the successful blast outcomes achieved using the eDev™ Electronic Blasting Systems for resue mining at SGM. Results to date, since commencement in March 2010, have been achieving significant benefits in terms of ore grade as confirmed by geologists grab sample grades. Face advance have also shown improvement with better breakage of perimeter holes giving improved face profile. These benefits are delivering increased productivity and safety performance when compared to other resue firing techniques.

Mar 21, 2011

By G R. Power

A useful way to assess potential productivity of SLC mines is by quantifying tonnes/drawpoint/day to be extracted from the mine. However limited industry information has been published to help mines benchmark this number. This paper assesses industry data which can be used to support estimates of potential productivity from new mines based on tonnes/drawpoint/day. The information used has been extracted from historical production schedules which indicate what was achieved, rather than what was planned. It has been assessed using an algorithm created for the purpose and is presented with discussion of varying definitions of active drawpoints, analysis of the data and inquiry into some of the underlying contributing factors.

Mar 15, 2021

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By M Recabarren, A Echeverria, J Ronda, J I. Guzman, R Dodds, G Juarez, E Vila-Echague

A strategic mine plan is a fundamental part of any mining operation. It must provide a realistic and operative extraction and processing schedule, and yield the highest value for the business. For open pit mines, the problem can be modelled as a set of blocks representing the deposit, for each of which we need to decide if it is going to be mined, if so, when and where it will be sent (process, stock or dump).This problem can be proven to be of NP-Hard complexity. The traditional approach used by mining engineers to tackle this complexity is to separate the problem into more tractable components, solving each separately. The first step is to use the Lerchs-Grossman (LG) algorithm to obtain the final pit limit, as well as a set of optimised pit shells (nested pits), using different input prices. Then, using this input, operational phases are designed. Third, the set of phases can be used as an input for a phase-bench style optimisation, usually using a mathematical programming-based algorithm.There are, however, several problems with this approach. First, dividing the problem into simpler parts has the consequence that any compromises made at early stages limit the potential value left for the following steps. Second, LG is a static algorithm, with no concept of the time-value of money, capacity limits, opportunity costs, etc. Phase design is essentially a manual step, for which nested pits provide insufficient information in practice, and therefore the quality of the result in terms of potential net present value (NPV) depends strongly on the experience and expertise of the designer. This means that key input data such as commodity prices, different processes capacities and mine movement limits, are considered only at scheduling, when there is little room for optimisation. This sequential approach limits the potential value in each step, where a simplified problem is addressed, instead of addressing the real, and more complex problem, which is dynamic and should be solved as a whole.We present in this paper an algorithm, and its commercial software implementation, that addresses the dynamic problem as a whole, simultaneously and automatically creating a high-value strategic mine plan that adheres to basic operational constraints, determining dynamic cut-off grades and delivering a set of phases which can serve as a much stronger guide than nested pits for the final design. We discuss some of the key elements of the algorithm and propose a new methodology for strategic mine planning, where phase design dynamically responds to mining strategy definition. Results using different mining and operational parameters on a fictitious copper deposit are used as a demonstrative example.CITATION:Juarez, G, Dodds, R, Echeverria, A, Guzman, J I, Recabarren, M, Ronda, J and Vila-Echague, E, 2014. Open pit strategic mine planning with automatic phase generation, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 147–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J D. van Wees

Preliminary project evaluation is relevant to the evaluation process of the decision makers (or executives) prior to making the critical business choices. Important to the assessment is an integrated sensitivity, scenario and risk analysis at every stage of a mining project. This should include the evaluation of different options taking into account uncertainties. Construction of interactive financial computer models where each element is functionally integrated into a fully integrated life-cycle allows rapid and automatic study of the sensitivity of each element through changes in the value of an input. The scenario analysis is the effect of changing more than one input at a time, organised through scenarios in a decision tree. Risk analysis is an integrated analysis of the effect of all uncertainties of the parameters, using Monte Carlo simulation. Key to the asset decisions process is that the decision maker is provided with the essential integrated decision information. We have clustered this information into several scenario groups. Within each group, two levels of uncertain information are distinguished: discrete scenarios critical for the decisions; and remaining uncertainty within the scenario (risk analysis) which can be modelled by continuous probability density functions (pdfÆs). For an asset, the relevant scenarios in each group and the associated continuous pdfÆs need to be defined. When the scenario groups and associated pdfÆs have been defined for the asset, the decision process can be started by structuring the different scenario groups in a Scenario Tree. A Scenario Tree contains decision and end nodes. Each end node corresponds to a completely defined mine project or asset model. The calculations for each end node result in a set of stochastic realisations for the reserves, production forecast, cash flow, and profitability indicators (NPV, IRR, DPR). Thus, a deterministic and fully probabilistic multi-commodity analysis tool is provided to investigate the sensitivity and robustness of decisions.

Jan 1, 2003

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J Heyes

Historically mining engineers haven't spent enough time planning waste dumps, but waste movement costs often outweigh ore haulage costs. There is a real incentive to plan waste dumps right the first time to minimise rehandle and final closure costs. At BHP Billiton Iron Ore there has been an increasing sophistication in waste dump design and they are becoming as important as the pit design. Closure landforms are now included in mining studies. Closure is embedded in the business planning cycle. The results from the recent life of mine study at Whaleback is a case in point where a base case of the shortest hauls with no closure constraints was compared against a closure case. A properly planned and executed waste plan revealed that no rehandle was required and haulage costs were eight per cent less if closure design implementation was carried out concurrent with mining. At cessation of mining the landforms were such that decommissioning of critical acid rock drainage dams and coverage of exposed pyrite areas could occur straight away, without the need for additional rehandle.  The paper also covers design and scheduling elements of waste design both in-pit and ex-pit, management of potentially acid forming material (PAF) and trends in PAF management and designing for final landform closure. This paper illustrates that there is value in terms of costs savings, sustainable outcomes and reputation if the mine planners are involved in the closure planning process.

Jan 1, 2009

This paper reviews some of the factors thought to control the formation of supergene gold in the Pacific and its Rim. Discussion of these should lead to reassessment of the economic potential of many areas. In several parts of the world many gold-bearing veins display rich gold values only in the oxidized zone, whereas beneath the present (or ancient) watertable the unaltered vein commonly holds only sub-economic refractory low grade sulphides or arsenides. In the Eastern Highlands of Australia some of the most spectacular concentrations of - gold have been found at shallow depths. For example, Harper (1918) describes the Canton mine in New South Wales which was stoped over a length of 180 metres from the 45 metre level to the surface. The reef yielded gold at 300 g/t in the upper levels, but became gradually poorer at depth. Present geologists of N.S.W. Geol. Survey, G.R. Mcllveen and B.P.J. Stevens, believe that many similar Australian enrichments were formed between the surface and its ancient water table level during the extended period of weathering in the Eocene or pre-Eocene. They concede, however, that further supergene movement of gold may have occurred since the early Tertiary. Large quantities of Mesozoic supergene gold of extreme fineness (Au 99.7%, Cu +òFe 0.3%; Leibius 1885) was found at Mt. Morgan near the Tropic of Capricorn in Queensland. Lower Jurassic sediments cover part of the gossan in a small depression caused by oxidation and collapse of the Main Pipe, thus showing that the supergene gold is pre-Lower Jurassic (Cornelius, 1968). Because the Lower Jurassic landscape around Mt. Morgan was mature with a surface slope of less than 10 (Playford and Cornelius, 1967), erosion would have been very slow. Moreover, once all sulphides had been removed from the ore body the Lower Jurassic environment would have reverted from highly acid to alkaline as it is at present. Accordingly, gold, goethite and 1. Dept. of Geology & Mineralogy, University of Queensland, St. Lucia, Australia,

Jan 1, 1987

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

An Integrated Geology-Mine-Plant and Eco-Efficiency Simulator for Anglo Platinum's Evaluation and Operational Improvement Initiatives

Sep 13, 2010

By A Li, H Jinto, M Laxman

The behaviour of tailings under cyclic loading has an impact on the stability and deformation of tailings dams and a good understanding of the cyclic behaviour of the tailings under earthquakes is important for tailings engineers and tailings operators for the design and safe operation of tailings dams. This paper presents an investigation into the cyclic behaviour of tailings using both laboratory cyclic direct simple shear (DSS) testing and numerical modelling. The laboratory testing involved cyclic DSS tests on gold tailings and zinc-copper tailings under different loadings and loading frequencies. The gold tailings specimen tested at a higher loading frequency and a higher cyclic stress ratio experienced spontaneous liquefaction during cyclic shearing and the zinc-copper tailings specimen tested at a lower loading frequency and a similar cyclic stress ratio exhibited ductile behaviour and liquefied due to cyclic mobility. The liquefaction behaviour of the tailings was modelled using an advanced constitutive model (UBCSAND), which was developed specifically to model soil liquefaction and strain softening under cyclic loading. The constitutive soil model presents the nonlinear soil behaviour under dynamic loading using a hyperbolic stress-strain relation. Dynamic analyses were carried out using a finite difference program FLAC. The cyclic stress-induced excess pore water pressures measured in the laboratory were modelled using numerical simulations of the laboratory tests under different loading conditions. The results of the non-linear dynamic analyses demonstrated the capability of numerical modelling of cyclic shearing induced excess pore water pressure and the onset of the spontaneous liquefaction. The laboratory investigation and numerical modelling technique provided the key properties and parameters for the dynamic analyses to assess the stability and deformation of tailings dams under design earthquake events. More importantly, the laboratory tests and numerical modelling provided some insights into liquefaction behaviour of the tailings during earthquakes. CITATION:Li, A, Laxman, M and Jinto, H, 2018. Liquefaction behaviour of tailings under cyclic simple shear testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 250–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018