Search Documents

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal' and by Chew and Connally' for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7' API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.' All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967

By J. J. Gilman

The data presented indicate that the critical shear stress and strain-hardening Thedatapresentedrate of a zinc monocrystal depend on the orientation of its slip direction with respect to its external boundaries. The tendency of a crystal to form deformation bands also depends on its shape. THE plastic behavior of pairs of zinc monocrystals in which both members of the respective pairs had the same orientation with respect to the longitudinal axis, but each had different orientations with respect to their rectangular external shapes, were compared in this investigation. The purpose of the investigation was to see what influence the shape or surface of a zinc crystal has on its mechanical properties. In a previous investigation of triangular zinc monocrystals,1 anomalous axial twisting was observed which seemed to be related to the triangular shape of the crystals. Wolff,' in 400°C tensile tests of rectangular rock-salt crystals bounded by cubic cleavage planes, found that, of the four equivalent slip systems, the two with the "shorter" slip directions yielded and produced slip lines at lower stresses than the other two. This observation and the work of Dommerich³ as formulated by Smekal4 as a "new slip condition" for rock-salt: "among two or more slip systems permitted by the shear stress law, with reference to the formation of visible slip lines by large individual glides, that slip system is preferred which has the shortest effective slip direction." More recently, Wu and Smoluchowski5 reported essentially the same effect for ribbon-like (20x2x0.2 mm) aluminum crystals at room temperature. Experimental Chemically pure zinc (99.999 pct Zn), purchased from the New Jersey Zinc Co., was the raw material. Glass envelopes, containing graphite molds and zinc, were evacuated while hot enough to outgas the graphite but not melt the zinc. At a vacuum of about 0.2 micron the envelopes were sealed off and then lowered through a furnace at 1 in. per hr so as to melt and resolidify the zinc and produce mono-crystals. One-half of one of the molds is shown in Fig. la. Each mold consisted of four pieces from a cylindrical graphite rod that was split longitudinally and transversely at its midpoints. Rectangular milled grooves 0.050 in. deep and % in. wide formed the mold cavity when the split halves were assembled with twisted wires. Fig. lb shows the specimen shape obtained when the top and bottom mold-halves were rotated 90" with respect to each other. Good fits prevented leakage and excess zinc was necessary to provide enough liquid head to fill the mold completely. In removing soft crystals from the molds it was impossible to avoid small amounts of bending. However, manipulations were carried out whenever possible with the crystals protected by grooved brass blocks. All specimens were annealed prior to testing. From the top and bottom sections of each crystal, X-ray specimens and tensile specimens 7 to 8 cm long were sawed. The tensile specimens were annealed inside evacuated tubes for 1 hr at 375°C. Next the crystals were cleaned and polished by 2-min dips in a solution of 22 pct chromic acid, 74 pct water, 2.5 pct sulphuric acid, and 1.5 pct glacial acetic acid.' Cleaning was followed by a 10-sec dip in a 10 pct caustic solution, then washed in water and alcohol, and dried. This treatment results in a bright surface covered by an invisible oxide film. The testing grips were a slotted type with set screws and were supported in a V-block during the mounting operations in order to avoid bending the crystals. A schematic diagram of the recording tensile-testing machine is shown in Fig. 2. The machine has been described elsewhere.' The head speed was 0.3 mm per sec for all tests. The crystal orientations were determined by the Greninger X-ray back-reflection method with an estimated accuracy of 1. Description of Crystal Geometry A schematic picture of a rectangular zinc mono-crystal is shown in Fig. 3. ABD designates the front edge of a basal plane (0001) of the crystal, the only active slip plane for zinc at room temperature. Of the three possible (2110) slip directions, the active one is indicated by an arrow. Cartesian coordinates are taken parallel to the specimen edges. The normal, n, to the basal plane (n is parallel to the hexagonal axis) has the direction cosines a, ß and ?. X0 = 90 — y is the angle between the longitudinal axis and

Jan 1, 1954

By C. N. Garman

Homestake-New Mexico Partners operate a 750-tpd carbonate leach uranium concentrate mill near Grants, N.M. The highly mineralized water available as process water leaves much to be desired. The 628 ppm as CaCO 3 makes the use of raw water very troublesome in pipes and on filter cloths. However, the residual sodium carbonate in the final filter cake going to tails makes an ideal softening agent. To take advantage of this fact, all makeup water used in the mill is first used as tailing slurry dilution water and comes to the mill from the tailings pond. The 5-acre tailings pond serves as a thickener and 100 to 150 gpm of nearly clear solution is decanted to a pump to be returned to the mill. Since this tailings water has small quantities of uranium in the solution an ion exchange scavenger unit was installed to remove as much uranium as possible. The ion exchange raffinate is then used as final filter wash ahead of the tailings slurrying step. In spite of the large settling area this return water is not clean enough for ion exchange feed. The solids present are very fine and composed of approximately 15 pct (by weight) burnable carbonaceous material common to the sandstone uranium ores in the area, 40 pct SiOz plus 45 pct CaC03. Laboratory work showed that this material responds very well to flotation. Before deciding to use flotation, various clarifying systems such as pressure leaf filters, sand filters, and continuous vacuum pre-coat filters, were considered. Each of these could have solved the problem but with much more operating labor, more reagents and greater installation costs than the flotation step. About 100 to 150 gpm of fouled water is fed to two 66-in. Fagergren cells, in series. Reagents used at the beginning were Arquad 2HT75 and Arquad C50, at the rate of about 1% lb per 8-hr shift, or about 0.0053 lb each per ton of ore. This did not completely remove the solids but does an acceptable job. Approximately 75 pct of the slimes are a size that can be caught on a 41-Whatman Paper are removed. Removal of these slimes also allows much better settling of the coarse nonfloatable material. Advantage is also taken of this fact in a small settling tank ahead of precipitation. Removal of this amount of the slimes makes the ion t:xchange feasible. PREGNANT SOLUTION CIRCUIT The carbonate? leach-caustic precipitation method of uranium concertration does not provide for any process purification step ahead of precipitation. Therefore, any fine solids getting into the pregnant solution through the filter cloth show up in the final concentrate. This, of course, lowers the grade, and, at times, the slimy nature of these very fine solids rendered final filtration of the concentrate difficult if not impossible At Homestake-New Mexico Partners a 75-ft thickener was available for gravity clarification of 100 to 120 gpm of this pregnant solution. However this did not sufficiently remove the slimes. Laboratory investigation of the whole range of flocculants that were suggested by literature, salesmen, and friends failed to turn up anything of consequence. A continuous vacuum pre-coat filter would do the job and was investigated. The capital cost and the operating labor and materials made this a last chance choice. Following work done in the metallurgical laboratory on the tailings return water, it was found that some changes in the reagent strengths and combinations made a very definite decrease in the solids in the pregnant solution. Concentrate grade improved about 5 pct anti the final product after drying had an appreciably greater bulk density. Compared to a cost of about 2.2e per ton for pre-coat filter opelation for cleaning just one circuit, flotation costs less than 1.0 per ton of ore for cleaning two circuits. While a pre-coat filter would do a more thorough job, the flotation does all that is required for either circuit. Gravity causes the froth produced to run back into the leach circuit. This does not appear to result in a build-up of objectionable slime. No extra manpower is required; the operators in the separate areas can observe the operation of the cells and mix the small quantities of reagents as needed. Normally the 66-in. Fagergren cell requires 15 hp per cell, but this very dilute slurry needs only 10 hp for both cells. Originally, a combination of the two Arquads mentioned previously served as frothers and promoters. As further testing

Jan 1, 1962

By L. H. Van Vlack, T. Y. Tien, R. J. Martin

The phase relationships of the MnTe-MnS system were studied by DTA procedures. There is an eutectic at 810°C with about 10 mole pct MnS-90 mole pct MnTe. An eutectoid occurs at about 710°C with approximately 7 mole pct MnS where the MnTe(NaCl) solid solution dissociates on cooling to MnTe(NiAs) and MnS. There is very little solid solubility of MnTe in MnS. ALTHOUGH MnS may exist in three different crystal forms,' only the NaC1-type phase is stable.2 Above 1040°C, MnTe also has the cubic NaC1-type structure. Below that temperature, MnTe changes to the NiAs-type structure.3 This phase transition is rapid for both heating and cooling. As a result the high-temperature crystal form of MnTe cannot be retained at room temperature. Because MnO, MnS, and MnSe are all stable with the NaC1-type structure, and MnTe has this structure at high temperatures,4 solid solution formation could be expected among these compounds. It is interesting to note, however, that a complete series of solid solutions exist only in the MnS-MnSe system,' and that the solid solution is quite limited in the MnO-MnS system.' The MnSe-MnTe system possesses a complete series of solid solutions at high temperatures with separation at lower temperatures.7 Although ion size may be critical in the miscibility of MnO-MnS, it is quite possible that the bond type plays a more important role with the miscibility of MnSe-MnTe. This would permit us to speculate that the miscibility gap would be extensive in the MnTe-MnS system. EXPERIMENTAL Preparation. The samples were prepared by mixing and compacting MnTe and MnS powders. The MnS was previously prepared through the sulfur reduction of Mnso4.8 The MnTe had been prepared by mixing and compacting double vacuum distilled metallic manganese and high-purity tellurium in stoichiometric ratio modified with 1 wt pct excess tellurium. The compacted powders were put in a graphite crucible which was sealed in an evacuated vycor tube. The free space in the vycor tube was made minimal to reduce the loss of tellurium. The sealed assembly was then heated slowly to about 500° C where the free manganese and tellurium reacted vigorously, melting the MnTe which formed. Only one phase, MnTe, was detected by X-ray powder patterns and metallographic techniques. Each compact of MnTe-MnS was placed in a graphite crucible and then sealed in an evacuated vycor tube. The samples were heated at 1250°C for 4 hr and furnace-cooled. Microscopic examination revealed no third phase beyond MnS and MnTe. A typical microstructure is presented in Fig. 1. Identification. X-ray powder patterns were obtained using 114.6 mm Debye-Scherrer camera and Fe-Ka radiation. Mixtures of cubic MnS and hexagonal MnTe were observed in all of the compositions prepared. No lattice parameter change was noticed among different compositions, indicating no solid solution could be retained at room temperatures between these two end-members. A lattice parameter of 5.244Å for MnS was obtained by the Nelson and Riley9 extrapolation method using the diffraction lines of (h2 + k2 + 12) equal 12, 16, 20, and 24. The values, a = 4.145Å and c = 6.708Å, for hexagonal MnTe were obtained from the (006) and (220) lines in the back-reflection region. These values agree well with the values reported by Taylor and Kag1e.10 Differential Thermal Analysis. A differential thermal analysis procedure was used to determine phase relationships since the high-temperature equilibrium conditions could not be retained for examination at room temperature, even when the sealed samples (~0.5 g) were quenched in water. The samples were sealed in an evacuated 4 mm vycor tube with a recess in the bottom to accept a thermocouple. An Al2O3 reference was similarly prepared and the two placed within a piece of insulating fire brick to dampen spurious temperature changes within the furnace. The furnace was controlled by a mechanically driven rheostat which increased the temperature at a rate of about 15°C per min. Known phase changes in the Pb-Sn system1' and the a-to-ß quartz inversion12 were used for calibration

Jan 1, 1969

By W. H. Smith

IN connection with some recent work on the effect of impurities on the ductility of chromium, it appeared desirable to know the solid solubility of carbon in chromium. A literature survey indicated that this information was not available. Although considerable work has been done on the Cr-C phase diagram,&apos;.&apos; previous investigators have been more concerned with the structure and phase boundaries of the carbide phases than with the terminal solid solution. The phase diagram shown in Fig. 1 is taken from the work of Bloom and Grant&apos; and represents the most recent determination. As indicated by the dashed line, the a solid-solubility limit was not determined. Experimental Procedure Alloys of chromium were prepared from hydrogen-treated and vacuum-degassed electrolytic chromium plus spectrographic grade carbon. The oxygen and nitrogen content of the alloys was <0.002 pct. After melting, analysis of the alloys showed them to contain 0.02, 0.08, 0.15, and 0.55 pct C. Pieces of the alloys were heated in a protective atmosphere to various temperatures and then quenched after holding for a time sufficient to insure equilibrium. Microscopic examination of the as-quenched alloys for the presence of a second phase was used as a measure of the solubility limit. The heats were made in a multiple hearth arc-furnace using a zirconium-gettered static argon atmosphere. A zirconium melt was made before each Cr-C heat. Triple melting was used to insure ingot homogeneity as shown by microscopic examination. The alloys were prepared by adding portions of a 4.5 pct C-Cr master alloy to high purity chromium. The carbon contents listed previously were those obtained by analysis. The nitrogen and oxygen contents after arc melting were both <0.002 pct. Sections 1/8X1/4X1/2 in. were cut from the 100-g ingots and a hole drilled in one end in order to suspend the sample from a molybdenum wire. After the surface was carefully cleaned, a sample of each melt was hung in a mullite tube heated externally by a platinum resistance furnace connected to a vacuum system. The lower portion of the mullite tube was sealed to Pyrex and closed off several inches below the furnace. This was filled with sili-cone oil kept cold by circulating cold water around the outside of the Pyrex. Quenching into the oil bath was achieved by melting a fuse wire supporting the sample. It required about 4 sec for the sample to cool from 1400" to 600°C. This severity of quench was considered satisfactory to freeze-in the high temperature equilibrium. For tests made at temperatures of 900" to 1200°C, heating was done in vacuum; for tests above 1200°C, an argon atmosphere was used. The holding time employed ranged from 12 hr at 900°C to 6 hr at 1400°C. Experiments were performed at temperatures of 900°, 1000°, 1100°, 1200°, 1300°, and 1400°C. Microscopic examination for evidence of a second phase was done at X1500. Experimental Result The microstructures of a 0.08 pct C-Cr alloy as-cast and after quenching from 1300°C are shown in Figs. 2 and 3. A 0.15 pct C-Cr alloy quenched from 1300°C is shown in Fig. 4. The data obtained from the quenching experiments is shown graphically in Fig. 5. If the Van&apos;t Hoff equation is obeyed, a plot on a logarithmic scale of the mol fraction of solute vs the reciprocal of the absolute temperature should give a straight line. For dilute solutions the weight percentage can be substituted for the mol fraction without introducing any appreciable error. The Van&apos;t Hoff equation can then be written as where H is the heat of solution in calories per mol. The slope of the straight line on the log pct C vs 1/T plot gives the value of AH. Assuming that the Van&apos;t Hoff equation is obeyed, which is probably justified for the dilute solution of carbon in chromium, the heavy straight line shown on Fig. 5 represents the best fit of the data. This line was obtained as follows. On Fig. 5 the results of the microscopic examination of all alloys following quenching were plotted and designated as to whether one or two phases were seen. Below 1100°C all alloys showed a second phase on quenching. The heavy vertical lines shown in Fig. 5 therefore represent the possible range of the ter-

Jan 1, 1958

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

By R. Hoffmann

THE Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. FIG. 1.-DAILY CAPACITY OF WAELZ PLANTS RUNNING OR BEING ERECTED. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper-Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. -The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928

By A. H. Grobe, F. N. Rhines

THE constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conventional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitution of its alloys desirable. As a part of a program for the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram [ ] (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (143.5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan&apos;s decrease in steel production and to that country&apos;s increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

By H. O. Hofman

The object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe1 in his classical paper " Colitributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks. 2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker3 and Addick. 4 The absorption of gases has received attention by Hampe: Stah16 and Heyn 7 The effects of casting-temperature have been noted by Stahl.8

Jan 1, 1908

By P. H. Fahlström

The Ebliden Company, originally entering the field of mining with the workings of the gold-copper-arsenic deposit at Ebliden, commenced zinc benificiation at Kristineberg in 1940 and lead mining at Laisvall in 1943. During the three last decades a number of mines has been developed for production, Today the Mining Division of BOLIDEN produces ore from 22 mines, operates 7 ore dressing plants and produces: [ ] Over two thirds of the lead contents are treated in the lead smelter of the company at Ri6nnskarsverken. The other part of it is sold abroad. The zinc content of the lead concentrates is recovered from the lead smelter at Ri6nnskarsverken. The zinc concentrates are shipped abroad to European smelters in Norway and Germany. Today BOLIDEN has its plants in the northern and the middle parts of Sweden. Figure 1. Straight lead ore, lead-zinc ores, lead-zinc-copper bearing ores and complex lead-zinc-copper and pyrite ores are treated in local and central plants with a capacity of 8.600 tpd. BOLIDEN also operates the low grade copper ore at Aitik at 7.000 tpd.

Jan 1, 1970

By G. E. Agar, A. L. Mular

G. E. Agar (Manager, Minerals Processing Research, International Minerals & Chemical Corp., Skokie, III.) — The author notes a discrepancy between the parameters a and ß which are the slopes of the size distribution and energy-size modulus plots respectively. The reason for the discrepancy and the systematic decrease in the magnitude of a with grinding time is abundantly clear from the work of Fuerstenau8 on dry grinding. Fuerstenau shows very clearly in his Fig. 5 that at short retention times the parameter a is the same as that obtained by sizing over the complete size range. From this figure, it is obvious that sizing to only 400 mesh gave distribution curves similar to Mular&apos;s - that is, the slope apparently decreased systematically with increased grinding. As a consequence of the improper determination of a, the magnitude of ß given by Mular must be larger than the true value. In order to demonstrate this, the following Fig. 6 was taken from Mular&apos;s paper (his Fig. 1). Fuer-stenau&apos;s results show that we can approximate the correct value of K by drawing lines parallel to the short retention time curves through the 400-mesh

Jan 1, 1963

By F. H. Rhines, A. H. Grobe

The constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conven-tional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitu- tion of its alloys desirable. As a part of a program far the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (I43. 5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By A. H. Grobe, F. H. Rhines

The constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conven-tional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitu- tion of its alloys desirable. As a part of a program far the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (I43. 5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1937 and the reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Library, Student .Relations, Speakers for Local. Sections and Student Societies, and Mining and Metallurgy. To these reports members are referred for further details. Finances.-Income for the year was the largest since 1930, the figure being $189,394, an increase of $18,803 compared with income for 1936, exclusive of a special Rocky Mountain Fund appropriation of $2500 in that year for visits to western schools and Local Sections. Major items of increase were: $8,000 from current dues and arrears; $7,700 from advertising in MINING AND METALLURGY and the two periodical "Technologies"; and $4,800 from sales of TECHNICAL PUBLICATIONS (pamphlets) and TRANSACTIONS volumes for both current and former years. Initiation fees and clues from new members declined $2,300, principally because of the larger &apos;proportion of Junior Members to Members among the new enrollments. Junior Members pay no initiation fee and dues are $10 compared with $15 for Members.

Jan 1, 1938

By Shiou-Chuan Sun

THE effects of oxidation on the flotation behavior of sulphide minerals have been extensively studied,1-3 but no similar study has been made of coals. Coals of bituminous and lower rank undergo atmospheric oxidation during mining and storage, and their degree of oxidizing increases with temperature4,5 and time of exposure.6 The problem of recovering fine oxidized coal from culm piles, rivers, and streams by froth flotation has become increasingly important to the coal industry as well as to those concerned with air and stream pollution. This paper describes the flotation behavior of oxidized and unoxidized coals and carbons in the presence of oily collectors and presents the reagents found effective in the flotation of oxidized coals and carbons. Except where otherwise stated, flotation tests were performed in a 50-g Denver flotation cell. Solid feed for each test was 30 g, and the pulp dilution was kept at 8.5. The -65 mesh coal sample was wetted by agitation with water in the flotation cell for 6 min, then conditioned with a predetermined amount of collector for 2 min, and finally floated with pine oil as frother for 3 min.

Jan 4, 1954

By Philip R. Whitney

Deposition of manganese oxides is of common occurrence in streams of the north-eastern United States. Manganese entering the stream in solution in ground water is oxidized and deposited in the stream, primarily as oxide coatings on detrital materials. Prevalence and thickness of the coatings increases with increasing particle size in the coarse sand and gravel range. A number of metals of economic and environmental interest are enriched in these coatings. Samples of 8 to 16 mm pebbles were obtained from two streams in the Shawangunk region of southeastern New York State, an area of know71 Pb/Zn/Cu mineralization. The pebbles were leached to remove the oxide coatings and the resulting solutions analyzed for Mn, Fe, Pb, Zn, Cd, Cu, Co, and Ni. Trace-metal/Mn ratios in these streams are generally one to two orders of magnitude higher than regional background values. Profiles of trace- metal/Mn ratios along the streams show considerable detail; contributions of metals from tributaries are sharply reflected in the metal content of the oxides. The potential advantages and disadvantages of using coated stream gravel for geochemical prospecting and environmental studies are discussed in the light of these and other data.

Jan 1, 1976

By E. R. Parker, E. A. Smith

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985

By E. A. Smith, E. R. Parker

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944