Search Documents

By C. Richard Tinsley

Like most minerals, coal is inherently a demand-limited commodity. The very sedimentary nature of its occurrence implies greater availability potential than demand. But this situation is overridden by economics among fuels, between coals, and within coal blends. Such considerations make coal forecasting a very hazardous profession indeed. THERMAL COAL If one thought that the lead times involved with a mining project were very long, one has obviously not been exposed to the planning process in the electric generation business - a process seriously confounded by shifts in load growth, environmental pressures, capital intensity, security of fuel sourcing, inter-fuel economics, and so on. But as a general rule, the near-term forecasts for thermal coal can reliably be based on a bottom-up, plant-by-plant analysis. Cement plant conversions can also be reasonably estimated next in order of reliability, although they have a much wider spectrum of coal qualities and fuel sources to choose from with a notably higher tolerance for sulfur and ash. Finally, industrial demand can be assembled from the estimates for conversions by pulp/paper plants, chemical plants, etc. The industrial sector is harder to estimate, since it may involve small boilers or dual-fired units. Assessing demand in the Pacific Rim is relatively a straightforward process in the near term because the major importing countries are all located on the Asian continent with either negligible or very minor (yet stable) indigenous coal production, (itself often operated on a subsidized basis). Furthermore, all imports are seaborne. These major importers are Japan, Korea, Taiwan, and Hong Kong with Thailand, Singapore, and Malaysia up-and-coming consumers. The suppliers to this market all have substantial reserves to back up decades of exports to these countries. Australia, the US, Canada, South Africa, China, and the USSR dominate the supply side. The second oil-shock of 1979/1980 has convinced the importers that reliance on oil can be expensive and eminently interruptible. Thus, they are determined to diversify away from oil' to nuclear and coal for generating electricity and for coal for other purposes where possible. This trend is seen to continue even in the face of the oil glut worldwide and oil-price reductions in early 1982. But the importers are also convinced that reliance on one coal source and, in particular, one infrastructure route for the coal chain from mine to consumer can be equally expensive and interruptible. Strikes in the US and Australia; excessive demurrage at certain ports; relegation of coal to a lower priority on multiple-use railroads in the USSR and China; and concern over escalation on high-infrastructure or high-freight coal chains are among the risks worrying the importers. As a consequence, Pacific Rim thermal coal purchases are being allocated among supplier nations, between ports, and within each country. An example of Japan's shift away from Australia and toward the US and Canada is shown in the estimates in Table 1. But the confidence of the import estimates deteriorates sharply beyond the plant conversion timetables and construction schedules in the near term. If part of the second generation of coal-fired power plants can handle lower-energy coals, the field of suppliers could widen to accept sizeable tonnages from Alaska, Wyoming, Alberta, or New Zealand resources. These supply sources generally have some infrastructure or freight advantage to compensate for their lower quality and to compete on a delivered energy-unit basis. These also offer diversification in sourcing. And the possibility of coal liquefaction in Japan further widens the sourcing network. A great number of Pacific Rim coal forecasts have been generated, especially for Japanese thermal-coal imports which are expected to grow strongly in the 1980's. Since the Japanese themselves have not yet settled their energy policy, the exact numbers are hard to call. Nevertheless, at 50 million tonnes of imports in 1990, Japan would consume 50-60% of the total Asian thermal coal imports as shown on Tables 2 and 6. The next most important consumers are the "island" nations of Korea, Taiwan, and Hong Kong (see Tables 3-5). All three are embarking on power plant developments usually with captive unloading facilities, capable of accepting more than 100,000-dwt vessels. Korea, with no-indigenous bituminous coal, is not especially enamoured with US coals, which are deemed too heavily loaded by freight and infrastructure costs -- up to 70% of the delivered price. Thermal coal contracts are presently split to Australia (70%) and to Canada (30%). Korea Electric Power Co. is already considering second-generation boilers capable of burning lower-quality coals than the present standard. Korea does burn domestic anthracite.

Jan 1, 1982

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation' of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,'-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals' force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.' The streaming potential

Jan 1, 1970

By R. T. Hukki

John F. Myers (Consulting Engineer, Greenwich, Corm.)—Since the art of comminution has lain practically dormant for many years, it is very interesting that R. T. Hukki approaches the subject with a new concept. One is reminded of the research carried on by A. W. Fahrenwald of Moscow, Idaho, a few years ago. Fahrenwald mounted a steel bowl on a vertical shaft. The balls and ore placed in the bowl were rotated at fast speeds, thus simulating the supercritical speeds used by Hukki. The rolling action of the balls against the smooth shell liner has pretty much the same effect. The action is horizontal in one case and vertical in the other. Both researchers report good grinding activity. It is also constructive that such able investigators give to the students of comminution their interpretation of their laboratory results in terms of large-scale operation. History shows that it takes a lot of time for such radically new ideas to be absorbed by the industry. Typical of this is the present-day activity of cyclone classification in primary grinding circuits. The idea of cyclone classification has been kicking around for 30 or 40 years. Certainly we all suspect that the ponderous grinding mills of today, and their accessory apparatus, large buildings, etc., will ultimately give way to small fast units, just as this has occurred in other industries over the past 50 years. At the moment there is no evidence that ball and liner wear is prohibitively high. In fact, at the time Fahrenwald was demonstrating his high-speed horizontal machine at the meeting of the American Mining Congress, several years ago, he assured this writer that the balls retained their shape much longer than they do in conventional tumbling mills. Rods and balls that slide (as some operators in uranium plants are experiencing) get flat. Apparently the balls have a rolling action. Mr. Hukki's references to the processing capacity of the Tennessee Copper Co. mills is adequate. Those studying this subject will be greatly interested in the paper presented by Richard Smith of the Cleveland-Cliffs Iron Co. at the annual meeting of the Canadian Institute of Mining and Metallurgy in Vancouver April 24, 1958. This paper will be published during the latter part of 1958 in the Canadian Institute of Mining and Metallurgy Bulletin. Hukki's pioneering spirit is to be commended. R. T. Hukki (author's reply)—It has been heartening to read the objective discussion by J. F. Myers. The sincerity of his opinions is further strengthened by the fact that the article he has discussed contradicts in a major way the parallel achievements of his life work. Myers is right in his opinion that in general it takes a long time before new ideas are accepted by the industry. On the other hand, revolutions usually take place at supercritical speeds. There are many indications at present that both the unit operation of grinding and the related subject of size control are now just about ripe for a revolution. In grinding, brute force must ultimately give way to science. Rapid progress can be anticipated in the following fields: 1) Autogenous fine grinding at supercritical speeds will be the first advance and the one that will gain recognition most easily on industrial scale. At this moment, little Finland appears to be leading the world. Crocker recently made a statement that in nine cases out of ten, your own ore can be used as grinding medium more effectively and far more economically than steel balls. This is true. The present author would like to introduce a supplementary idea: In eight cases out of the nine cited above, it can be done at the highest overall efficiency in the supercritical speed range. Fine grinding must be based on attrition, not impact. The path of attrition may be vertical, horizontal, even inclined. 2) In coarse grinding, the conventional use of rods is sound practice. However, even the rods can be replaced by autogenous chunks large enough to offer the same impact momentum as the rods. To obtain the momentum, the chunks must be provided with a free fall through a sufficient height in horizontal mills operated at supercritical speeds. Coarse grinding must be based on impact. Detailed analysis of the subject may be found in a paper entitled "All-autogenous Grinding at Supercritical Speeds" in Mine and Quarry Engineering, July 1958. 3) All conventional methods of classification, including wet and dry cyclones, are inefficient in sharpness of separation. Continuous return of huge tonnages of finished material to the grinding unit with the circulating load is senseless practice. In the near future the present methods will be either replaced or supplemented by precision sizing. These three fields are also the ones to which J. F. Myers has so admirably contributed in the past. Fine Grinding at Supercritical Speeds. By R. T. Hukki (Mining EnGineERInG, May 1958). Eq. 9, page 588, should be as follows: T , c, (a — 6') n D Ltph On page 584 of the article the captions for Figs. 4 and 5 have been placed under the wrong illustrations and should be interchanged.

Jan 1, 1959

By E. A. Breitenbach

A computer program has been developed to afford rapid and complete quantitative log analysis for exploration and production decisions. The computation consists of automatic selection of tops and bottoms of porous intervals from the digitized data, and then point-by-point calculations within each selected interval. Nearly all log types can be analyzed. This paper presents the calculation techniques found to be appticable to machine evaluation and gives examples of their use. INTRODUCTION As the quantitative interpretation of well logs entails repetitive use of charts and equations, it is natural that digital computer programs would be written. A Universal Log Interpretation Computer Program (ULICP) has been developed to afiord rapid and complete analysis for exploration and production decisions. Application of this program enables the log analyst to: (I) apply rapid quantitative log analysis for exploration and production decisions on either a field, a well or on a single zone basis; (2) apply concepts of interpretation requiring detailed numerical analysis; (3) analyze all porous intervals on each log, rather than a few selected zones, and complete the analysis in less time than previously required. Computations are reported for every digitized point in each zone; (4) use empirical techniques applicable to a given area as an integral part of the computation; (5) experiment with the empirical coefficients and exponents in the interpretation equations to find the best possible solution; and (6) automatically plot both the original and computed data to scales analogous to the field prints. The primary utility of a log interpretation program stems from its ability to do an overwhelming amount of work with very little man-power. If a calculation procedure or thought process can be formalized to the extent that step-by-step logic can be written, a computer program can be developed that follows this logic. The major question is one of economics. A feasibility study of the costs for such a program indicates that digital processing is economical primarily as a means of increasing the productivity of the log analyst. In effect, the probability of missing productive intervals in any well, because of a lack of time to do detailed calculations, is greatly reduced. The nucleus of ULICP is programmed to compute large sections of a suite of logs by selecting zones automatically and then performing all pertinent computations on a data point by data point basis within each zone.'.' An entire suite of logs can be processed in this manner with very little manual intervention. Sufficient programming logic is available so that each log analyst can request computations pertinent to his area. These requests are made by simple additions or deletions of information on the input header cards. Hence, the log analyst is always in complete control of the computation process. The evaluation of a suite of logs requires pre-editing, digitization, computation, presentation of results and interpretation. Work by the log analyst is reqilired only in pre-editing and interpretation. Thus, he is allowed more time for comprehensive interpretation, rather than calculation. For continuity, the discussion of ULICP is organized sequentially: pre-editing, digitization, computation and presentation of results. DISCUSSION PRE-EDITING The extent of pre-editing prior to computation is dependent on the format of the original data. For analog prints, it requires inspection, correlation and editing of the logs, plus the entering of required data an special forms. For digitized data such as magnetic tape field recordings, only the special forms are necessary. The process for analog prints will be given here. The inspection and correlation process involves the selection of sections for digitization and the correlation of the traces to a common depth. To decrease the cost of digitization, traces that exhibit large variations in shale formations can be redrawn to a non-zero baseline. The next step is to enter all pertinent data on the input header cards. The header cards presently used for ULICP are presented as Figs. 1 through 6. Cards 1, 2, 3 and 4 (Fig. 1) are defined as the Main Header Cards. They describe the particular well for output identification and give basic information. Cards 5 through 15 (Figs. 2 through 6) are defined as the Block Header Cards. As such, they define the log types and the interpretation parameters for the block of data immediately following. Cards 1 through 10 are required for every computer run. Cards 11 through 14 pertain only to nuclear logs. Card 11 is required if any nuclear log is supplied, and cards 12 through 14 are required only when gamma-ray, density or neutron log data, respectively, are supplied. Card 15 (Fig. 6) must be supplied when cross-plot calculations are required. Either two- or three-component

Jan 1, 1967

By J. Gordon Parr, D. H. Polonis

High purity alloys of titanium and iron, made by a technique of levitation melting, have been investigated with particular reference to martensite formation and decomposition in the hypoeutectoid range. A preliminary study has been made of the occurrence of the phase corresponding to the structure Ti2Fe. MANY of the previous investigations of Fe-Ti alloys have been made using Kroll sponge as a source of titanium; and the subsequent heat treatments to which alloys have been subjected has, on occasion, led to further contamination. Worrier,',' who suggested a part of the equilibrium diagram for the binary system, and Wallbaum and coworkers,3-5 who worked largely with iron-rich alloys, all used Kroll sponge. Van Thyne, Kessler, and Hansen,6 in their determination of the equilibrium diagram, used iodide titanium for alloys up to 30 pct Fe. Duwez,7 who measured the M. temperature of titanium binary alloys with many solute elements, used iodide titanium in all cases except in his work on Ti-Fe alloys for which he used Kroll sponge. The investigation of the supposed phase Ti2Fe by Rostoker8 nvolved the use of iodide titanium. A section of the constitutional diagram, after Van Thyne et al., is reproduced in Fig. 1. Frequently too much stress is placed on the effect of contaminants in equilibrium and nonequilibrium systems, but there is no doubt that titanium alloys are extremely susceptible to interstitial atoms. Consequently, the main purpose of the work to be described was to determine those features of phase transformations in pure Ti-Fe alloys that were considered of importance in commercial heat treatments. For, although commercial alloys may not be of high purity, the investigation of a system uncomplicated by traces of impurity is a desirable starting point. Another incidental feature, the occurrence of Ti2Fe, was also investigated. The entire study was carried out using powders obtained from alloy ingots, for diffusion reactions are often more rapid in small particles than in bulk specimens. The frequently adopted practice of ascertaining phase constitutions by X-ray analysis of powders, and relating these to the microstructures and mechanical properties of bulk specimens, is considered by the authors to be open to criticism. In the martensite reactions in the Fe-Mn system, for example, it has been shown- hat similar phase distributions in solid and powder may result in different hardness values and appearance under the microscope; and it is possible that similar anomalies might occur in the Ti-Fe system. Consequently, in order to

Jan 1, 1955

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By Haley, D. F.

WHEN operations were first started at Climax in 1917 by the Climax Molybdenum Co., they were pioneering in the molybdenum industry for little was known relative to the uses of molybdenum or the metallurgy of molybdenite concentration. Concentration of molybdenite is relatively simple today but in 1916, when the Climax deposit first attracted attention, it presented serious difficulties. Little was known, in fact, even about the assaying of such low-grade molybdenum ores. Mine samples were sent to at least a dozen of the best laboratories in the United States and average values reported varied from 0.4 per cent to 1.0 per cent MOS2. Owing to the wide variations in MoS2 content obtained from reliable chemists, the actual value of the ore was most uncertain. This variation occurred repeat¬edly over a period of six months in 1917. It was finally decided, as a last resort, to cut several tons of sample from the tunnel and have a mill test made, using the recovered MoS2 per ton as the grade of the ore, for a small error in the assaying of the concentrate would not materially affect the results. These mill tests were made by the General Engineering Co. (Callow) at Salt Lake City. The results proved an ore of commercial grade and indicated the flotation process for the best metallurgy. Based upon these tests, the decision was made to build a 200-ton flotation plant. At this time, the art of flotation was

Jan 1, 1946

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.' The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.' The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

By George F. Weaton, Carleton C. Long, H. I. Najarian

Partial descriptions of the operation of the St. Joseph Lead Company's Joseph-town smelter have been published. In, 1936 the electrothermic production of zinc oxide was described;' in 1939 appeared a description2 of the electrothermic method of producing zinc metal. Inasmuch as the plant capacity has more than doubled, and in view of the fact that operating practices have improved greatly since these publications, it seems worth while to prepare a fresh description of the present-day elec-trothermic zinc plant and practice. Josephtown smelter is situated on the south side of the Ohio River about 3 miles below its confluence with the Beaver River. In addition to river barge, the smelter is served by Pennsylvania state highway No. 18 and by a spur line of the Pittsburgh and Lake Erie Railroad (N.Y.C.). A recent extension of this spur line connects with the Pennsylvania Railroad. As originally contemplated the plant was to handle only the product of the com-pany's own mines in St. Lawrence County, New york, but owing to the incessant demand for zinc and zinc oxide, it has been necessary to supplement New York concentrates with foreign ores (principally from Quebcc and the Argentine). The general operational procedure followed comprises roasting the sulphide con-centrates, converting the sulphur dioxide into sulphuric acid, preparation of a strong-structure sinter from the calcine, crushing &lid sizing of coke, reduction of coke-sinter mixture by electrothermic means, condensation of the evolved zinc vapor to make zinc metal or burning of the zinc vapor to make zinc oxide, collection and packing of the zinc oxide. Dusts recovered by the roaster and sinter Cottrells are treated in the leach plant for separation of lead sulphate, cadmium metal and zinc sulphate. The general flowsheet is shown in Fig. I. Principal Items OF Equipment Roaster Plant Concentrate drier, 6-ft. 'ia. by 4O ft. 5 in., countercurrent, direct gas-fired. 3500-~on concentrate storage in three vertical steel tanks. Five modified Nichols-Herreshoff twelve-hearth roasters, 21 ft. 6 in. in diameter. Four fans for shaft-cooling air. One threedrum Stirling water-tube waste-heat boiler, 4'8 hp., 200 1b. Per sq. in., with connections to upper and lower balloon flues. Direct gas-fired countercurrent rotary-kiln roaster for Cottrell dust. Necessary conveying equipment, described below. Instrumentation consists of: draft indicators, (3d hearth); various manometers; pyrometer served by thermocouples in each hearth, entrance and exit of waste-heat Joseph. entrance and exit of each hot Cottrell; roaster draft recorder and shaft air-pressure controller; temperature recorder and controller (10th and 12th hearths); SO* recorder (waste-heat boiler n

Jan 1, 1944

Sifto Salt Div. of Domtar Chemicals Ltd. has developed a new method for installing roof bolts in the high backs of its 1-million-tpy rock-salt mine at Goderich, Ontario, on the east shore of Lake Huron. The method teams a telescoping- boom hydraulic crane with a specially developed combination auger-drill and bolt-tightening ma- chine. One man, controlling all operations from a basket supported at the end of the crane's telescoping boom, installs an average of 100 5-ft roof bolts per shift, at heights to 45 ft. The mine has very long backs that are not as stable as might be expected. The result has been that roof scaling has occupied an unusually high percentage of the underground work force. About six years ago, company officials decided to go to 100% roof bolting of all backs as a safety measure. The present roof-bolting equipment is the result of a development program instituted at that time to find a faster and more economical method for doing the job.

Jan 9, 1967

By Alexander L. Holley

THE 400-ton testing machine, ordered in June, 1875, by the United States Board appointed to test "iron, steel, and other metals," has lately been completed at the Watertown Arsenal, thoroughly proved and accepted by the Board. The excellence of the machine in every respect is more than satisfactory, and its accuracy is at first sight astonishing, although an investigation of its principles must show that if the weighing apparatus will weigh at all, it must do so with perfect accuracy, because all its movements are absolutely without friction. The proof experiments were numerous, and the effects of recoil after sudden ruptures at maximum loads, were watched with great care, but without much anxiety, because the weighing parts affected are by no means delicate in structure, and their motion is almost infinitely small. Among the tests were the following : A forged link of hard, wrought iron, 5 inches in diameter between the eyes, was slowly strained in tension, and broke short off with a loud report at 722,800 pounds. The diameter before breaking at the point of fracture was 5.04 inches; after breaking, 4.98 inches. In order to see if the weighing parts had been disturbed by the recoil, which was obviously near the greatest recoil the machine will ever suffer, a horse-hair was next tested ; it was 7-1000ths of an inch in diameter; it stretched 30 per cent., and broke at 1 pound. Other horse-hairs vary in tenacity between 1 and 2 pounds. Of course, the accuracy of the machine on such delicate specimens, and indeed on specimens having some hundreds of pounds tenacity, has been checked and proved by other weighing machines. A 5-inch round bar, turned down to 3 5/8 inches diameter along the centre, was pulled apart at 430,200 pounds tension. Then some more horse-hairs were tested ; also copper wires 19 1/2-1000ths of an inch in diameter, which averaged 25 pounds tenacity..

Jan 1, 1879

By J. Alfred Berger, O. M. Katz

Selected samples of hydrided Zr-Hf alloys were rapidly quenched to voom temperature and exrtrnined metallographically, by X-ray diffraction, and through micro hardness studies to confirm high-temperutuve data Confirming experiments sllowed that there were five phases in this Lernary system: 1) hextrgonal with lattice parameters similar to that of the initia1 Zr-Hf alloy but slightly enlarged due to dissolved hydrogen; 2) fee with properties of a brittle, intermediate, hydride compound; 3) fct with c/a crvoltnd 1.07 and which appeared as a neetilelike precipitale; 4) hexagonal, designated ?, with c/a ratio of 2.37; and 5) orthorhombic, designated X, with a = 4.67, b = 4.49, and c = 5.093 and whose tnicro-st?ruct~ival nppetrl-nnce depcncled o/i, heat lvecrt~r~ent. The tetragonrrl phase never crppeal-erl witkorct the cubic hydricle. Abpecrrtrnce of 0 and A also tlependet on the hafnium content of the zirconium. A previous paper' on the Zr-Hf-H system described the thermochemical data obtained with a high-vacuum, high-sensitivity mirrogravimetric apparatus. This data presented a fairly complete picture of the phase relationships at elevated temperatures. However, it could not establish the actual crystal structures, lattice parameters, or metallographic disposition of the hydride phases. The present complementary study utilizes X-ray powder patterns along with light and electron microscopy to characterize completely the five hydrided phases found in Zr-Hf-H alloys quenched to room temperature. Crystallographic features of the zr-Hf,2,4 zr-H,5-7 and Hf-H8 systems have been summarized in Table I. Designations of a, ß, and ? were retained in the Zr-Hf-H system for the phase regions through which the pressure-composition isotherms always sloped. However, it was not firmly agreed that these were single-phase regions.' In fact, the region designated y always contained a cubic as well as a tetragonal phase after quenching to -196°C. MATERIALS Preparation of the high-purity Zr-Hf alloys has been described.' The four zirconium alloys which were hydrided contained 37 wt pct Hf (23 at. pct), 51 wt pct Hf (37 at. pct), 73 wt pct Hf (58 at. pct), and 91 wt pct Hf (82 at. pct), respectively. These were designated B-2, B-4, B-6, and B-8. Photomicrographs of the initial alloys showed the material to be quite clean as would be expected from the precautions exercised in producing them. However, there were a number of annealing twins but no other subgrain structure. In addition to the four original alloys, fifteen hydrided samples were observed at room temperature. Hydrogen compositions are given at the top of Tables I1 to V. APPARATUS The phases present at elevated temperatures were studied by quenching hydrided samples to room temperature by two different methods, both under vacuum: 1) fast cooling of the sample tubes of the microgravimetric apparatus1'9 with flowing air and 2) rapid quenching into liquid nitrogen. The cooling rate for 1) was 750° to 250°C in 30 sec. Since the microbalance chamber was not designed to permit very rapid cooling of a hydride sample, all liquid-nitrogen quenching was done in an auxiliary experiment. The auxiliary quenching apparatus consisted of a small-bore, high-temperature furnace, a sealed SiO2 tube containing the sample, and a dewar quenching flask filled with liquid nitrogen. The hydrided sample, previously quenched in the microgravimetric reaction chamber, was placed in a platinum boat in a vacuum-degassed SiO2 tube. A zirconium wire getter and degassed SiO2 rod, to reduce the internal volume, were also in the tube. After sealing the tube under vacuum the zirconium getter was heated to absorb the last traces of gas. Only the sample was heated at the reaction temperature for the desired length of time, and then the tube dropped through the opposite end of the furnace into the dewar. A quenching rate of 200" to 400° C per sec was estimated. Analyses of samples after the auxiliary experiment also showed practically no increase in oxygen or nitrogen content from heating in the SiO2 tube. All of the samples were examined at room temperature by the X-ray powder method. The majority of the powder patterns were obtained with double nickel-filtered CuKa radiation after 8- and 16-hr exposures in an 11.48-cm-diam camera. Cobalt and chromium radiation were also used to spread out the high d value end of the Pattern. Such patterns readily identified the minor phases. NO oxide or nitride lines were found. Where sharp back-reflection lines existed it was possible to reduce the

Jan 1, 1965

By W. C. Lacy

THE Cuajone porphyry copper deposit is the northernmost of a group of three deposits in southern Peru controlled by the Southern Peru Copper Corp.-Toquepala, Quelleveco, and Cuajone— all within a 20-mile belt. Although small pockets of high-grade copper oxide ores were worked in the Cuajone area in the 19th century, it was not until 1939 that its potentialities as a disseminated deposit were recognized by 0. C. Schmedeman. An exploratory drilling pro- gram was begun in December 1942 and continued until early 1945. The program was revived in November 1952 and completed early in 1954. Early exploration was by diamond drilling. Later exploration was predominantly churn drilling, with diamond drilling used only for wildcat holes. Along this northwest-trending belt of deposits. which follows the western slopes of the Andean Range, quartz-monzonite has invaded earlier dio-rite intrusives and a series of warped and tilted Cretaceous volcanic flows. Little faulting of consequence has been recognized within the mineralized areas. Sulfide minerals were introduced into all these diverse rocks, and mineralization was followed by erosion, oxidation, and enrichment. In Late Tertiary and/or Quaternary time the entire

Jan 1, 1959

By Eugene Stebinger

INTRODUCTION. A LARGE number of papers and reports dealing with the coalfields of Montana have been published + during the last 30 years, but the information is much scattered, appearing in many technical and scientific journals and in government reports, in many cases inaccessible to those most interested. In recent years, especially since 1905, ,our knowledge of the geology and coal contents of the important fields of the State has been much increased. Fairly specific and detailed information is. at hand on all of the principal coal-bearing areas. The fields for which data are not at hand are small and inaccessible, and their omission will not materially affect an estimate of the coal resources of the State, viewed as a whole. The paper here presented is a summary of existing information, all sources having been freely utilized in its preparation. The viewpoint adopted is that of the geologist, rather than that of the engineer or colliery operator, because by far the greater portion of the coal areas present have had only the most meager development, making information that, will aid in prospecting and opening the at present little used coal lands of paramount importance to those interested in the coal fields of the State.

Jan 9, 1913

By Luis Salazar

Internal improvements are the great seals; stamping upon the history of nations their epochs of peace, in which notable enterprises are conceived, and fresh impulses given along the path of progress. Such forerunners of national benefits have never been so notable in Mexico as in the last four decades of the nineteenth century, during which the national faith in the consolidation of peace has been a guaranty of the development of all the elements of national prosperity. Among all the improvements which have been realized with the unanimous approbation of the people, the railroads occupy a preferred place, for upon them depends the expansion of commerce, of agriculture and of mining, the three great factors of the wealth of Mexico. In a country so extensive as the Mexican Republic, where the inhabitants are greatly scattered, and great distances separate the producer from the consumer, the only way to encourage home industry, and the development of commerce, agriculture and mining, is to construct railroads, which shorten distance, facilitate transportation and minimize its costs. The mountainous character of the country makes the navigation of its rivers practically impossible, except very near to

Jan 1, 1902

By T. B. Massalski, Horace Pops

The occurrence and the temperature dependence of the athermal martensitic transformation in bcc Cu-Zn ß-phase alloys have been studied by cold-state microscopy, differential thermal analysis, and electrical -resistivity measurements. CinenzatograpJzic studies have shown that in the majority of alloys the transformation occurs in two stages. A thermoelastic phase, having a 'needlelike" uppearance, forms initially at the MS temperature and grows relatively slowly, chiefly in the edge (lengthwise) direction. With further cooling, an additional martensitic phase forms in rapid bursts at a lower temperature, MB, Both martensitic phases appear to have the same cry stallographic habit hut their modes of formation and growth are different. For the composition range studied, between 38.55 and 41.49 wt pct Zn, the habit planes determined are close to the (2.17 ,12) plane of the matrix, in general agreement with the prediction of the phenomenological theory of martensite formation. Thermal cycling through the MB temperature produces permanent plastic deformation in the 0 matrix and gradutally eliminates the typical burst phenomena. Thermal cycling only through the MS temperature produces no noticeable deformation effects. THE bcc Cu-Zn ß-phase alloys tend to become unstable at low temperatures and undergo a martensitic transformation,'-3 but the details of the transformation have not been completely determined. Following earlier metal log raphic and X-ray work1 Tichener and ever' determined by means of electrical-resistivity measurements the temperature range of the martensite transformation during continuous cooling. The transformation temperature was found to decrease with increasing zinc content, becoming about -130°C for an alloy containing 40.04 wt pct Zn. Hull and Garwood3 made a metallo-graphic study of Cu-Zn 0 brasses at temperatures down to -160°C, and determined the habit plane of the transformation product for an alloy containing 38.88 wt pct Zn. No metallographic studies below liquid-nitrogen temperatures have been reported. The martensitic transformation in ß-brass alloys can also be induced by deformation.1,4 The MD temperature corresponding to the appearance of the strain-induced martensite is some 300°C higher than that observed without strain, and hence the transformation can be strain-induced in alloys containing a higher percentage of zinc. Massalski and Barrett4 found that alloys containing as much as 51.89 wt pct Zn could be transformed into a faulted hcp structure by cold working at liquid-helium temperature. Because the details of the MS temperature and morphology reported in the literature are somewhat incomplete, a further study has been made of some of the above features. A design of a cryogenic stage for optical metallography5 has permitted the examination of specimens at temperatures down to 4.2oK, and the use of a cinecamera has permitted a study of the morphology on cooling and heating. The particular aim of the present work was to examine the transformation temperatures, the habit planes, and the growth morphology over a wide composition range in the ß-phase field. The effect of thermal cycling upon the subsequent transformation was also examined.

Jan 1, 1964

By W. F. Holbrook, T. L. Joseph

The problem of sulfur control is important in all blast-furnace operations but particularly for certain grades of steel because of the rigorous specifications. During the past decade the tendency has been to produce pig iron and hot metal of lower sulfur content. As most of the sulfur in the iron originates in the fuel, the use of high-sulfur coke demands modifications in practice to meet sulfur specifications. While it is generally known that high temperatures and more basic slags favor desulfurization, operators as a rule produce the most acid slag that will permit proper desulfurization. The viscosity of blastfurnace slag has been thought to be related to desulfurization and has been investigated by Feild and Roysterl, also McCaffery and his associates*, but apparently no systematic effort has been made to determine the relative desulfurizing powers of slags over the range of composition encountered in practice. Development of Testing Method Because slag and metallic iron are immiscible, the desulfurization reaction is heterogeneous, occurring only at the interfaces between slag and metal bodies. In the blast furnace the newly reduced iron, containing FeS, descends through the slag bath probably either as small drops or streams, at the interfaces of which desulfurization occurs. After its descent through the slag the iron collects to form a bath of metal, at the top surface of which desulfurization reaction probably occurs. These two steps have been thought to account for all desulfurization in the blast furnace. Kinney3 found that metal removed from the blast furnace just above the tuyeres contained three to four times as much sulfur as the iron at cast. Herty and Gaines4 conclude that most of the sulfur is removed while the metal is passing through the slag. Mund, Stoecker

Jan 1, 1936