Search Documents

By R. R. Vandervoort, W. L. Barmore

Tensile creep experiments were conducted on high-purity, poly cvystalline rhenium from 1500" to 2300°C at stresses from 1500 to I0,OOO psi in a vacuum of 10-a torr. The apparent activation energy for creep was 60 kcal per mole, and the steady-state creep rate varied directly with stress to the 3.4 power. Dislocation substructure that developed during creep was studied by transmission electron microscopy. Possible rate-controlling deformation mechanisms are discussed. The creep behavior of most metals at elevated temperature can be represented by the following equation:&apos;&apos;&apos; t = Cf(s)(^)(s/E)nD [1] where i = steady-state creep rate, C = constant, f(s) = a function involving microstructure, s = applied stress, E = the average elastic modulus at test temperature, n = constant, D = diffusion coefficient According to this well-established relationship, metals with higher elastic moduli and lower diffusion coefficients should have greater creep resistance at the same stress and temperature and equivalent mi-crostructures. While no diffusion data are available, the diffusivity of rhenium should be less than that for most other refractory metals because of its high melting point and hcp crystal structure. The Sherby-Simnad relation for calculating atomic mobility in metallic systems3 predicts that the diffusion coefficient for rhenium is less than that experimentally determined for tungsten4 in the temperature region 1500. to 2200°C. At these temperatures the elastic modulus for tungsten5 is only slightly larger than the extrapolated modulus for rhenium.6 Thus, rhenium is a good possibility for a a high-temperature structural material, but few data on the creep of rhenium have been reported. This investigation was undertaken to study the high-tempera-ture deformation behavior of rhenium in detail. EXPERIMENTAL TECHNIQUES The material used in this study was consolidated from high-purity powder. After cold pressing the powder to a plate a in. thick, the billet was sintered in hydrogen at 2250°C for 24 hr. The plate was reduced to 0.100 in. by cold cross rolling with intermediate anneals at 1650°C for 20 min between passes. The plate was further reduced to 0.060 in. by unidirectional cold rolling with similar heat treatments between passes, and then finally stress-relieved in hydrogen at 1650°C for 30 min. Specimens tested at 1900°C and below were pretest-annealed at 1900°C for 2 50 hr. Specimens tested above 1900°C were pretest-annealed at 2400°C for 5 hr. The impurity content in the "as-received" plate was quite low, table I. Essentially no change in impurity levels was detected in specimens after creep testing. All creep tests and annealing treatments were conducted in a vacuum of 10-8 torr in a test furnace heated by a tungsten mesh element. The load was applied to the specimens through a bellows, and stresses were maintained to ±1 pct of the selected value by periodic corrections for changes in specimen cross-sectional area during creep and for changes in the bellows spring force due to load column extension. One-inch-diameter tungsten force rods were used in the hot zone of the furnace. Deformation at temperature was measured by optically tracking gage marks on the specimen. Temperature was measured by a calibrated optical pyrometer and was determined to ±5"C. Grain sizes were determined by the linear intercept method and specimens were examined in the "as-polished" condition, using polarized light. Specimens annealed at 1900°C had a grain size of 52 ± 5µ , and those annealed at 2400°C had a grain size of 148 * 11 µ. Pieces were cut from the gage section of creep-tested specimens and planed to a thickness of about 0.010 in. by spark discharge machining. Thin foils for viewing by transmission electron microscopy were obtained by electropolishing in a solution of 6:3:1 ethyl alcohol, perchloric acid, and butoxy ethanol, respectively, using the window technique. Bath temperature was —4OoC, and the cell potential was 35 v. The foils were examined in Siemens Elmiskop I, operating at 100 kv. RESULTS AND DISCUSSION In order to analyze the results from creep experiments, Eq. [I] is rewritten in the following form: <=Kf(s)ne-/RT [2] where K = constant, ?// = apparent activation energy for creep,

Jan 1, 1970

By Roger V. Pierce

INTRODUCTION IN the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centered upon haulage, hoisting equipment, mill flowsheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materials. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain ore bodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered ore bodies are moving rapidly from stopes to reduction plants-because it is now possible to develop an ore body and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials of mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining. In some places it has been found economical to change from one system of stoping to another that more readily allows the application of mechanical muck-handling equipment. Where blocks are worked faster, the cost of materials, time, and labor is cut drastically. This favorable situation allows more manpower to remain on straight breaking and timbering-or straight production mining. More-over, when blocks are mined faster, more floors can often be mined vertically before the mucking or wheel floor is moved. This results in several direct savings. There are cases where it has been proved that by working a given block faster more area, longitudinally or vertically, could be mined at one time, thus permitting the reduction of development cost. (Fig. I.)

Jan 1, 1943

By James P. Savely, Victor L. Kastner

Inspiration Consolidated Copper Company is currently mining in four pit areas; Live Oak, Red Hill, Thornton and Joe Bush Extension, near Globe, Arizona. Small satellite orebodies lying outside the main pits have been mined out in a series of small open pits. Major slope instability has affected production in every pit. Some consequences of the instability have been; (1) Serious interruption of mining plans, which resulted in deferred ore production, lost ore, reduced mining rates and increased stripping requirements. (2) Forced replacement of crushing facilities. (3) Serious effects on other production facilities. The introduction of a slope stability monitoring and control function as an integral part of mine planning has been successful in reducing the impact of these failures and will eventually result in economic pit design based on probabilistic slope analysis. This case history presents a brief review of the problems associated with slope instability at Inspiration&apos;s mines followed by a more detailed report on one specific failure area in the Thornton pit where the use of horizontal drain holes for slope stabilization appears to be successful. Relationships between slope movement rate, rainfall, and mining activity are shown.

Jan 1, 1983

Edward Halse, Puerto Berrio, Colombia, So. Amer. (communication to the Secretary*): The Taviche mining-district is generally known as " Taviches," being named from the two villages called respectively San Pedro Taviche and San Jero-nimo Taviche. It is so called by Jose G. Aguilera, in his paper on the Geographical and Geological Distribution of the Mineral Deposits of Mexico;&apos; and in published reports by the late N. W. Rudston Read ;2 and by Juan de Dios Villarello3 The region is a large one, measuring about 24 miles long and 7 miles wide. Dr. Chance, in his interesting paper, tells us very little about the nature of the ores, and, with regard to the geology of the district, contents himself with observing that " the country, as a rule, consists of eruptive rocks; and no evidences of sedimentary strata appear near the mines." The latter part of the above statement is hardly correct. The formation is mainly

Jan 1, 1906

By Frank E. Neil, O&apos

The formation tester, as the name implies, is a tool built for testing the contents of sands encountered in drilling Wells Without actually cementing casing on the sand. The tester was developed in the Mid-Continent and has been in use commercially there since about 1926. However, some two dozen patents have been issued on formation testers dating back to the seventies. The method apparently was an outgrowth of the old Mother Hubbard grain or bean packer, used around casing before the days of cementing casing. These packers were also seated in a tapered hole and if the formation tested was not satisfactory the casing was pulled loose and the hole taken down to another formation. A great deal of experimental work has been done in its development, and as a result of this work the formation tester became an accepted integral part of the petroleum development in California. The formation tester was introduced into California some three years ago by M. 0. Johnston. Months of discouraging and expensive work followed its introduction into this state, but one organization after another tried the tool and its use is now fairly general. Shortly after Johnston began testing in California, the Halliburton tester was also introduced into the state and now another tool is being introduced, the Shaffer-Roles tester. Principle and Operation of Testers The principle employed in all formation testers is that of packing off the fluid in the hole above the formation to be tested and thereby prevent,ing it from having access to the testing tool. This permits the fluid contained in the given formation to have unrestricted access to the tool. It is accomplished by running the tool and packer on the bottom of the drill pipe; the valves in the tool being closed while going into the hole to prevent fluid from entering the drill pipe. The packer is then seated at the desired point, trapping the drilling fluid above it. When this has been done, the valves in the tool are opened and the fluid from the formation is allowed to enter the empty pipe through the tool. If the

Jan 1, 1934

By J. G. Early, F. V. Lenel, G. S. Ansell

The isothermal shrinkage rates of copper-powder compacts were determined in the temperature range from 760o to 1060oC. The rates for compacts fabricated from a pure spherical copper powder were compared, on the one hand, with those fabricated from a spherical powder containing a dispersion of aluminum oxide in the copper matrix and, on the other hand, with those fabricated from a pure copper powder having irregularly shaped particles. The irregular copper-powder compacts shrank much faster than the spherical copper-powder compacts and these, in turn, shrank faster than dispersion -strengthened copper -powder compacts. The experiments were run under a small external load. By varying this load, the stress dependence of the isothermal shrinkage rate could be measured for compacts from spherical-copper powders. This stress dependence was found to be approximately proportional to the 4th (dispersion-strengthened alloys) or 4.5th (pure metals) power of the stress. It is concluded that the material-trans port mechanism is due to dislocation climb rather than to Herring-Naharro creep. In this investigation the isothermal shrinkage rates of compacts made of copper powder with an average particle size of 70 g in the temperature range from 780o to 1060°C were studied. The aim of the investigation was to determine the mechanism of material transport responsible for the shrinkage of these compacts. Since the phenomenon observed in this investigation was shrinkage of compacts at high temperatures, it will be necessary to consider all the material-transport mechanisms possible in sintering. It is unlikely that evaporation and condensation, surface diffusion, or even volume diffusion of vacancies, in which surfaces of small radius of curvature are vacancy sources and those of larger radius of curvature vacancy sinks, will materially contribute to a sintering process involving shrinkage, i.e., one in which the centers of adjacent particles move towards each other. The two principal mechanisms which were considered were the so-called Nabarro-Herring mechanism and a plastic deformation mechanism by dislocation movement. Both of these mechanisms were originally conceived to explain creep, i.e., the plastic deformation of metals at elevated temperatures under a constant applied stress. The shrinking of metal-powder compacts which was studied in this investigation can be readily treated as a creep process. This means that the shrinkage rates observed are considered as creep rates under the influence of an applied stress. It is true that the stresses in sintering experiments are generally not constant but decrease continually with time, but, by considering creep rates or shrinkage rates over a relatively short time interval, the small changes in stress during this time interval can generally be neglected. Nabarro-Herring microcreep is a high-temperature deformation mechanism which is caused by a diffusional flow of vacancies from boundaries under a tensile stress towards those under a compres-sive stress. Herring1 has shown that in this type of microcreep the strain rate e is proportional to the applied stress and follows an equation of the form ma, aexp(-Q/RT) [l| where <j is applied stress, Q is the activation energy for self-diffusion, R is the gas constant, and T is the absolute temperature This type of creep can explain the shrinkage of a porous compact. The surface of the pores are subjected to the tensile stress of surface tension, while the grain boundaries are under a compressive stress also due to surface tension. Vacancies diffuse from the pore surface through the lattice to the grain boundaries, where they are eliminated. In order to maintain vacancy equilibrium at the pore surface the vacancies leaving the region of the pore surface are replenished from the volume of the pore, which means that the pores shrink.

Jan 1, 1964

By Thomas T., Read

THROUGHOUT the Colonial era, Philadelphia was easily , the leading city of North America, and it still held that position at the end of the period, with a population of about 25,000, though closely pressed by Boston, which had slightly over 20,000, and New York, which had nearly as many. It was the center of a region in which mineral industry was important. Thomas Rutter&apos;s bloomery, built in the Schuylkill valley in 1716, was quickly followed by many others, and during the Colonial period at least 20 blast furnaces, 45 forges, and iron- works of other types were built in eastern Pennsylvania, which easily led all the other colonies in iron manufacture. During the Revolutionary period others were erected as far west as Fort Loudon, in the Cumberland c alley.^ After 1800 the rapid development of the anthracite mining industry profoundly affected Philadelphia&apos;s, development, since transportation of the coal was then necessarily by water, and the streams of the anthracite . regions mostly flowed into either the Schuylkill or the Delaware Rivers. With an abundant near-by supply of coal and iron, with the seat of government, which had been there since 1774, and with a National Bank established there in 1791, one would have seemed safe in prophesying, at the beginning of the nineteenth century, that Philadelphia would permanently remain the leading city of the United States. Education in Philadelphia was at first wholly in the hands of the Quakers, who had established a "Public School" there in 1689, but in November 1739 George Whitefield, who had created a sensation in England by his preaching, though only 24 years old, passed through Philadelphia on his way to Georgia to found an orphan school there. He preached a series of sermons in Christ Church that were so disturbing to the established church that on Nov. 25 the Rev..Richard Peters (who was also Provincial

Jan 1, 1941

By David Moskowitz, Ira Binder, Robert Steinitz

THE hard refractory borides of the transition elements of the 4th, 5th, and 6th groups of the Periodic System have been the subject of a number of recent investigations.&apos;-&apos; It is well known now that most of these elements form several different borides, and Kiessling8 has summarized the rules which govern to some extent the arrangements of the boron atoms in the various structures. Melting points of a few borides have been published." The systems Fe-B, Ni-B, and Co-B have been reported," but, as these borides are rather low melting, they are outside of the groups of boron compounds considered here. Brewer&apos; has tested the stability of various borides and estimated a number of eutectic temperatures between different borides, but in no case was the complete system of a transition metal and boron investigated. The phase diagram becomes of special importance if the preparation of the borides from the elements in powdered form is considered; the lowest eutectic temperature will determine the first appearance of a liquid phase. Also, the knowledge of high temperature phases, if they exist, is important for the preparation of bodies from these borides by hot pressing or sintering. During the investigation of various metal borides,7 it was found that there were more boride phases existing in the Mo-B system than reported by Kiessling." They occur, however, only at temperatures above 1500°C and were, therefore, not found by him. This led to a study of the equilibrium diagram of the Mo-B system. ranging from 0 to 25 pct B and from room temperature to the liquidus. Part of this investigation was reported during the "Research in Progress" session at the 1952 Annual Meeting of the AIME.11 Raw Materials and Preparation of the Borides The raw materials used were commercial molybdenum and boron powder, both supplied by the Molybdenum Corp. of America. The molybdenum powder was 99+ pct pure? while the boron powder contained about 83 to 85 pct B. A large percentage of the impurities in this powder was oxygen, with the rest formed by iron, calcium, and unknown substances. The low purity of the boron used was, however, not considered detrimental to the final product, as most of the impurities evaporated at the high temperatures at which the borides were formed. The final product always had a minimum purity of 96 to 98 pct (figured as molybdenum and boron), with carbon, iron, and probably oxygen being the remaining products. Carbon is usually present as graphite. The chemical analyses always confirmed the compositions which corresponded to the crystallographic structures as determined by X-ray diffraction, and the boron content of the finished product agreed closely with that of the starting mixture; no boron was lost during the boride preparation. The chemical analysis methods employed for molybdenum and boron were previously described by Blumenthal.12,13 The powders were mixed by hand in the desired proportions, compressed at room temperature under low pressure, and then heated under hydrogen to about 1500" to 1700°C in a graphite crucible to form the borides. Usually, the three well-known borides Mo,B, MOB, and Mo,B,, which are stable at room temperatures, were prepared in this way, and all other compositions were made by mixing these borides in various ratios or by the addition of molybdenum or boron powders for the very low or very high boron contents. Preparation of two-phase compositions directly from the elemental powders was tried only occasionally to check whether equilibrium could be reached in this way. Experimental Procedures The stable borides were mixed in the desired ratios and heated under hydrogen in graphite crucibles to various temperatures. The well insulated crucibles were heated in a high frequency induction furnace. Special care was taken to obtain exact temperature measurement, which proved much more difficult than originally anticipated. It is believed that individual temperature measurements have an error of less than ±25ºC, while melting or transformation temperatures are accurate within ±50°C. The temperatures were measured with an optical pyrometer which was aimed at the closed end of a graphite tube extending down into the crucible. close to the samples. Attempts to measure directly through the hydrogen exit stack failed. The crucible arrangement is shown in Fig. 1. Heating was done at a slow rate to be sure that the temperature inside the crucible was uniform. The specimens were kept at the final temperature for about 30 min. For the investigation of high temperature phases, some samples were quenched. They were heated, without atmosphere protection, in a very small graphite crucible which could be rapidly removed from the high frequency coil, and dropped into water. These quenched samples were afterwards annealed to establish the equilibrium at lower temperatures. The melting points or the positions of the solidus and liquidus lines were determined by heating the specimens to various temperatures and examining them at room temperature for evidence of a liquid phase. These results were checked later on by thermal arrest curves, especially to determine the exact position of the eutectic temperature line. For this purpose about 200 g of the boride were melted in a graphite crucible, in an arrangement similar to Fig. 1. Slow cooling was assured by very good

Jan 1, 1953

By R. R. Sayers

THE South African Mining and Engineering Journal recently pointed out that no satisfactory solution of the question of compensation for silicosis can be arrived at by placing further liability of an inequitable nature upon the mines. There are at present 35 scheduled mines liable to contribute to the annual levy of $800,000 and provide for the net outstanding liability of $6,400,000. Several of these mines have, as yet, not been able to set aside sufficient funds against their out- standing liability to the Compensation Fund. The gold producers declare that the gold mining industry today is passing its zenith, and that the production of gold will decline, with a consequent lessening of the spending power of the mines, which in about ten years will be reduced to a great extent unless encouragement is given for the opening of new mines. It is during this period of decline that the mines will be required to meet the large burden already created by miners&apos; phthisis. In England the Workmen&apos;s Compensation Act, 1925, was extended to industries involving exposure to asbestos dust.

Jan 1, 1931

There are no data available of shipments until 1858, and then estimated, when railroad service became available. By reason of the iron made in the county, and the large amounts of salt, the tonnage used locally was quite large, and until 1860 these are estimated from the probable salt and iron production. After 1859 the tonnages shipped by rail are partly estimated from the total shipments of the Allegheny Valley Railroad from four counties. It is believed that the totals are below, rather than above, what the actual production was. While considerably larger for the same years than figures given by the Secretary of Internal Affairs and census reports, these data were always too low in those days, partly because of lack of facilities for gathering them, but more largely because of the strong prejudice existing in those days against furnishing such data to any governmental agencies.

Jan 1, 1942

By Charles H. Foreman

IN JUNE 1921, the Sullivan &lining Co., owned jointly by the Bunker Hill and Sullivan Mining & Concentrating Co. and the Hecla Mining Co, started work on the development of the Star Mine. The development work contemplated called for a crosscut from the Hecla workings on the 2000 level to the Star ledge. The length of crosscut necessary to encounter the Star ledge was approximately 8900 ft. from the Hecla shaft. By using workings formerly made by the Hecla Mining Co., only about 8100 ft. of actual crosscutting was necessary. This crosscut has a direction of S 20° W and would have a tendency to crosscut any ledges in the intervening ground.

Jan 1, 1924

By C. M. Smith

HOWARD N. EAVENSON, acting for the last time as president of the Institute, presided at the annual business meeting on Tuesday afternoon at 4 o&apos;clock. He spoke briefly of his visits with Local Sections last fall, and read a scholarly address on "Mineral Fuels and Civilization," scheduled for early publication in these columns. Karl Eilers presented the Treasurer&apos;s report, showing last year&apos;s income to be $134,967.44, compared with expenses of $133.266.51. Comparable figures for 1933 were $121,689.90 and $115,462.60. The Institute&apos;s peak income was in 1923 about $208,000. Newell G. Alford read the report of the Membership Committee showing 750 new members elected and placed on the rolls in 1934, compared with 328 in 1933. Losses by resignation last year were 81, compared with 262 in 1933; and 691 were suspended for non-payment of dues, compared with 747 the year before. Total membership, including 579 Student Associates, was 7742 at the end of 1934. Applications for membership have been coming in freely the last few months.

Jan 1, 1935

By DR. DOUGLAS

Discussion of the Paper of Dr. Douglas, presented at the Toronto Meeting of the Institute, July, 1907 (Trans., xxxviii., 455 to 471). EDGAR HALL, Silverspur, Queensland, Australia (communication to the Secretary*) :-Dr. Douglas has written on this subject before, and his influence has had a powerful effect on the side of freedom among the younger generation of engineers. Moreover, it is not the first time that he has attributed the decline of the copper-smelting industry in Swansea to the secrecy maintained by the firms there engaged in smelting-operations. In this latter statement I think his conclusions are open to criticism. Whether the firms referred to have suffered by their secrecy is their own business-I. bold no brief for them ; but that the decline of the copper-industry at Swansea was inevitable seems to me to be proved conclusively by Dr. Douglas&apos;s own writings. In his paper on The Copper Situation,1 Dr. Douglas says "In comparing iron and copper mining, . . . it must be remembered that 2 tons of average iron ore from the most prolific source now available will make 1 ton of metal; whereas from 33 to 75 tons (say an average of 50 tons) of copper ore must be mined to produce 1 ton of copper." And further: "Last year&apos;s production of iron was made from approximately 50,000,000 tons of ore. Our copper mines, to yield a production of 900,000,000 pounds, must have handled approximately 22,000,000 tons of ore, or nearly half the quantity raised from our iron mines." Is not this the key to the whole situation ? In transporting the 50,000,000 tons of iron-ore, 25,000,000 tons of the metal iron were carried so much nearer to the market, but the transportation of 22,000,000 tons of copper-ore would have carried only 450,000 tons of the metal copper nearer to its ultimate destination. The small percentage of copper available in its ores makes

Sep 1, 1908

By KING HAMILTON GRAYSON

IRON and steel were the only basic industries in the Soviet Republic in 1928 that lagged behind the pre-war production on a comparative basis. This was due to the almost complete obliteration of all industrial units manufacturing iron and steel products during the Revolution, which resulted in the production of 1921 being only 4 per cent of that of 1913. By the end of 1927 the production of pig iron had reached a point equal to 70.5, per cent of 1913; steel was 84 per cent ; and rolled iron was 78 per cent. According to the. planned program of the Supreme Economic Council, the pre-war level of the iron and steel industry was to have been reached and exceeded during 1929-30. The production of the entire period from 1917 to 1928 in comparison with 1913, is shown in the following table

Jan 1, 1929

By Lewis T. Wright

(Pittsburg Meeting, March, 1910.) I HAVE long been aware that ferruginous copper furnace slags if fused in the electric arc will yield metallic iron containing copper, and in order to confirm this knowledge, and to obtain further information of the behavior of such slags in the high temperature and reducing conditions of the electric furnace, a number of samples of slag were fused in an experimental electric furnace. The results obtained, given in Table I., show that a very large amount of metallic iron was produced, and that this iron carried with it practically all the copper, gold, and silver, and more than 50 per cent. of the sulphur, of the original slag. The metallic buttons formed in the electric furnace were clean, hard, but not brittle.

Mar 1, 1910

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of&apos; the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By Wheeler P. Davey

In an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. l.) Fig. 2 is a photograph of the end of the punching, showing the hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of radiographing metals. In order to gain some preliminary data, several pieces of 1/2-in. (12.5-mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter I.........................................1/4 in. =6.3 mm 2........................................1/8 in. =3.l mm. 3................................... 1/16 in. = 1.6mm. 4....................................... 1/32 in. = 0.8 mm. 5........................................1/64 in. = 0.4 mm. Exposures were made on Seed X-ray plates at 20 in. (50 cm.) distance with Coolidge tube X-117, operated on Scheidel-Western induction coil with mercury turbine break. The X-ray plate was placed on a sheet of 1/8in. (3.1-mm.) lead. The steel was placed above this and a Iead

Jan 1, 1916

By Thomas A. Lang, John A. Bischoff

The use of rock bolts for the support and stabilization of coal mining excavations was introduced over 30 years ago and, since that time, has progressively increased until today it is the primary means of support and stabilization of large underground openings. Early analytical studies and work with photoelastic and physical models established that even highly fragmented rock could be stabilized by rock bolting and form a load-carrying structural member that would span an opening. For stability, interaction of the bolts is essential and it depends on the bolt tension, the length and spacing of the bolts, the characteristics of the rock, and the applied load. However, the development of an explicit functional relationship embracing all these factors proved to be elusive. A review of the early rock bolting investigations led to the concept that the basic element of a rock bolted roof is the reinforced rock unit (RRU), consisting of an individual bolt and the rock immediately surrounding and adjacent to it, and to the development of mathematical equations which give the minimum bolt tension required to ensure that the RRU&apos;s are stable relative to one another and act together as a structural member. Analytical procedures have been developed for integrating RRU&apos;s into a reinforced rock structural (beam-arch) member which spans an underground opening and providing a rational basis for the design and installation of rock reinforcement systems.

Jan 1, 1982

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work&apos; the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,&apos; Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

By A. W. Schlechten, R. F. Doelling

Parkes&apos; process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,&apos; raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes&apos; crusts by one of the authors&apos; gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes&apos; process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes&apos; crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper&apos; on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned&apos; supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952