Search Documents

By Ryan Garvey

A numerical investigation is made into unstable failures of coal pillars (i.e. coal bumps) using the finite difference software FLAC3D. A static energy balance is first derived to calculate the excess energy released as a consequence of unstable failure in rock. Two- and three-dimensional mining layouts are then assessed on their bump-potential based on the magnitudes of excess energy released during simulated pillar failures. A three dimensional pillar model is developed to represent tributary area loading of an infinite room-and-pillar layout. Pillar strength and brittleness characteristics are calibrated using a Mohr-Coulomb strain-softening constitutive law to simulate width-to-height ratio coal pillars ranging from 1:1 to 5:1. Width-to-height ratio pillars 1:1 to 3:1 release large magnitudes of excess energy as the pillars fail, representing massive collapse of room-and-pillar layouts. The larger pillars maintain their residual strength during failure; however significant excess energy is still released during temporary reductions in pillar strength. A two-dimensional model is then constructed of a gate road pillar failing due to elastic rebound of the surrounding rock mass. Soft loading conditions initiate unstable failure for all pillar widths, while the total magnitudes of excess energy increase with the size of pillar being modeled. The results from these tests indicate that excess energy may be used as a direct assessment of the bump potential of simulated mine layouts.

Jan 1, 2013

By Erdal Unal

In order to define the support parameters, by use of empirical approaches, it is particularly important to analyze the rock-load height that should be controlled by supports. The controlling mechanism however, depends on the type of support used there- fore, the rock loads should be treated differently. In this paper, an empirical equation is introduced which relates the rock-load height (ht) to a quantitative rock quality index (REIR), and roof span (B) as fallows:

Jan 1, 1986

By I. Geldmacher

In-Seam Seismic (ISS) methods have been used extensively worldwide for the past 10 years to assist mine planning, espe¬cially longwall mining in coal seams. The technique is only starting to gain wide acceptance in North America where it is being applied in a much wider variety of applications than was initially considered. Surveys elsewhere have concentrated on the detection of faults (structures) in coal mines prior to longwall mining. The majority of surveys in North America has been the location of abandoned workings which were not adequately surveyed prior to closure. Modeling data based upon the lithological logs, geophysical logs and interpreted sections show whether the method will be successful prior to carrying out the survey. The surveys have been performed to locate abandoned wor¬kings from the surface and underground using both seismic reflection and transmission techniques. Data from coal seams in both Illinois and West Virginia will be presented. A second method where ISS surveys are being applied to detect old workings will be presented. The ISS tomography produces an image of the P-wave and Channel Wave velocities which is representative of the material through which the signal traveled thus identifying the location of the old workings. Data from Texas will serve as an example.

Jan 1, 1990

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By David Newman

Landslides and soil creep often occur with varying degrees of severity on steep slopes within Southern Appalachia. Ground movement may take place over years with subtle changes in topography and vegetation or it can occur rapidly in response to water inflow or disturbance at the toe of the landslide. Although the ground movement typically is restricted within the soil and colluvial layers, failure can extend into the weathered rock zone. Certain areas of Appalachia are described as "slide prone" because of historical precedent. To develop a profile of "slide prone" areas, the strength and physical properties of the soil and colluvium, topography, groundwater and surface water runoff, present and historical land use, and any surface disturbance are examined in detail. These attributes are useful in determining whether an area is potentially unstable before surface development including construction, logging, or mining. Recommendations are provided to avoid initiating ground movement concurrent with mining operations.

Jan 1, 1998

By Ken Barish

Jane Mine of the Keystone Coal Mining Corporation was started in 1962 and is in the Lower Freeport seas located in Armstrong County, Pennsylvania, approximately 45 miles northeast of Pittsburgh. The mine is a slope/shaft complex with the cover ranging from 100 feet at the slope to 450 feet near the back end of the property. The seam height ranges from 48 to 72 inches. A variety of roof conditions have been en¬countered, and an equal variety of roof control systems have been tried with varying degrees of success. Initially, places could be mined as deep as 100 feet without any permanent roof support. After several problems and the advent of the Health and Safety Act of 1969, roof control became more and more prevalent and predominant at the Jane Mine. It started with 4 foot conventional oolts. As the mine progressed in the northeasterly direction, roof conditions changed from the extremely good roof that was encountered initially, to bad roof; and other types of roof support were required. Sixty pound rails and 6 inch 25 pound to the foot steel I-beams were used for supplemental support in long life headings such as belt and track. Resin bolting was done in many areas for long life support due to the deterioration of the shale roof over time. Several areas had to be abandoned because of uncontrollable top.

Jan 1, 1984

By Deren Zhu

The principle of roof control in longwall mining is to control main roof fractures so as to reduce roof weighting, plus reasonable and effective design of supports to reduce the convergence and premature caving of the immediate roof. This paper introduces a comprehensive test for better roof control based on the geological conditions of coal seam No. 16 in Zaozhuan Colliery, China.

Jan 1, 1990

By Douglas Morrison

Hardrock mines in Ontario generally operate at between 3,000 and 7,500 ft below surface and generally experience significant rockburst activity below 5,000 ft. Since the introduction of bulk mining techniques around 1980, the safety record of Canadian hardrock mines has improved dramatically. However, the process of improvement was not a smooth one and, in the early years, the number of accidents and fatalities actually increased. One incident in 1984 that resulted in 4 fatalities in Ontario initiated a complete re-examination of mining practice and by the mid 1980s many changes had been introduced, driven by new non-prescriptive mining legislation. These changes affected not only the technical discipline of mining engineering but also the management of operational procedures and, together, they resulted in the significant improvements that have continued to this day. The analysis of the rock-fall related fatalities showed 5 major causes (loose, scaling, installing support, collapse and rockburst) and by the mid 1990s fatalities in all of these categories, except rockbursting, had been eliminated and even then, all these rockburst fatalities occurred in one mine which was closed shortly afterward. This paper discusses both the technical and social reasons for the initial failure and the ultimate success in improving the safety of these mines, with implications for mines in other major mining jurisdictions.

Jan 1, 2003

By H. Maleki

Gob pressure measurements were made in a Western U. S. coal mine as part of a long-term program to evaluate cave progress and to determine the influence of geological discontinuities on caving conditions, load transfer, and resulting instabilities. Gloetzl cells were selected for the measurements due to their simple, robust construction and a history of being able to monitor pressures in a broken medium. A methodology was developed for the successful installation and protection of the cells and hydraulic lines in the gob as the face retreated. The measurement indicated a cave progress controlled by the frequency of, major faults. The pressure-mining progress profile was compared to those observed in other parts of the world. It was concluded that the significant differences in profiles was caused by the thick-bedded strata, the existence of high lateral stresses and the spacing between faults. Recommendations are given for future applications of Gloetzl cells for gob pressure measurements.

Jan 1, 1984

By A. Wahab Khair

This paper presents an analysis of surface ground movements recorded from two longwall mines in Northern West Virginia which operate in the Pittsburgh Seam. The instrumentation areas consisted of four panels, two at each mine, covering various sections with unique topographic features. Instrumentation consisted of survey monuments on 25 to 120 ft. spacing. Vertical and horizontal ground movements were measured at specified intervals to determine subsidence rate, developing and final subsidence profiles, angle of draw, horizontal displacements and associated strain profiles. A relationship between panel depth and width and the subsidence factor was also developed.

Jan 1, 1988

By Gustavo Herrera Rico

As part of a general effort to increase safety, efficiency, and profitability of its mining operations, MICARE personnel with the support of NorWest Mine Services, Inc. determined that the key to improving development mining was the implementation of roof bolting as the means of primary roof support for both main entry and longwall gate road development. Until mid-1994, MICARE had relied exclusively upon primary roof support systems composed of heavy steel beams and wooden posts. Support systems were designed, implemented, and evaluated that were successful in controlling the mine roof under extreme geological conditions. This paper describes the geological challenges, support selection criteria, and presents the instrumentation and 'mine measurements made to assess the bolting performance during the development and retreat mining process of longwall mining.

Jan 1, 1997

By Xianming Zhou

Mining economics is such that too conservative in safety will result in a considerable penalty in mining cost. However, initial planning and design of a mining project often must be done without complete information. The assurance of economical and safe mining is thus difficult. This study is focused on the improvement of the mine design associated with Zhaoyuan Gold Mine in P.R. China as more information becomes available. Attention is given to the selection of backfill structures. Based on a proposed practical finite element model, a design, which is believed to be not only reliable but also cost-effective, is recommended for further mining operations in this mine.

Jan 1, 1989

Effective strata control, utilising fully encapsulated roof bolts, is dependent on the installed quality of the reinforcement elements. One mechanism by which fully encapsulated roof bolts may become less than fully effective is by gloving (glove fingering) and un-mixing of the resin. Following some small roof failures containing gloved bolts, investigations have been undertaken in some New Zealand coal mines to determine the extent of, and mechanisms involved in, the gloving of fully encapsulated roof bolts for a range of roof types and installation methods. Gloving, in this context, refers to the resin cartridge partially or completely enveloping a length of the bolt, typically with unmixed resin filler and catalyst/hardener remaining within the cartridge. Results have shown that gloving and un-mixing is a systematic and widespread phenomena, occurring across a range of resin and/or bolt manufacturers, and across a variety of roof types. Gloving was found in bolts installed using: hand held pneumatic and continuous miner mounted hydraulic methods, under run of mine (ROM) conditions by mine workers, and under controlled "best practice" conditions. The roofs bolts investigated are all 1800mm (6ft) long, and have shown that, on average, 485mm (-19") of the bolt length is gloved and/or unmixed. This equates to a 27 percent reduction in effective bolt length. The effected length of bolt is sufficient to impact on the load transfer/reinforcement capabilities of the bolt system, and hence impacts on the design assumptions and subsequent stability assessments. Furthermore, there is a direct relationship between the mechanism for the gloving of bolts and an increased occurrence of resin loss and reduction in encapsulations length in soft (less than 10 MPa) and/or highly fractured rock. Investigations have concentrated on developing an understanding of the mechanisms involved. This has been undertaken using both field installations and recovered bolts, as well as test bench trials. The mechanisms involved have been confirmed as being: the development of a pressure front as the bolt encounters the resin and is spun up the hole, which, in turn, leads to over-pressurisation and radial expansion of the resin cartridge, resulting in an increase in diameter of the plastic resin cartridge, which allows the bolt to be spun up into the cartridge without making sufficient contact to shred the cartridge or the hardener tube, resulting in an unmixed portion of resin.

Jan 1, 2003

By Takashi Sasaoka

EGAT Mae Moh Lignite Mine in Thailand produces about 16 million tons of lignite annually from open-cut mining. The coal is used to generate 2,400 MW of electricity. In the near future, however, the coal must be extracted from underground at 400? 500 m (1,312?1,640 ft) deep from the surface. The problem is the thickness of the coal seams. There are two coal seams that are about 25 m (82 ft) thick with 20?25 m (66?82 ft) of interburden between them. Up to now, many mining systems for thick coal seams have been used and improved in the world. However, where the thickness of coal seams is beyond the limitation of the current mining technology and system, an applicable mining system has to be introduced, considering influencing factors such as caving and subsidence. In order to investigate thick seam mining systems and propose a new mining system in ultra-thick coal seams in Thailand, a joint research group was established by Japanese and Thai researchers and mining engineers in early2009. This paper describes underground mining systems for thick coal seams and proposes an innovative underground mining system for thick coal seam, ?eco-friendly underground mining system?, considering geological, geotechnical, and environmental conditions in this mine. This paper discusses its applicability to this mine by means of numerical analysis from the geotechnical point of view.

Jan 1, 2011

By Zuoliang Xiu

Experience indicates that rockbolting is the most efficient and cost effective means of supporting gateroads of retreating longwalls. However, gateroads supported solely by rockboltiug currently accounts for less than 16% of the 4500km of annual gatemad drivage in China According to a stated target of the Ministry of Coal Industry, this percentage should be at least 50% by the year 2000. Since the learning stage of the technology which is indicated by low drivage rates and frequent roof falls in rockbolted gateroads must be overcome , strategies for the application of rockbolting to gateroads have become the focus of discussions on this topic. This pap presents the recent development on longwall gateroad rockbolting technology in China The development work has concentrated on understanding the mechanism of rockbolting; establishing new design procedures of bolting parameters fix gateroad support upgrading the consumable; optimizing bolt installation procedures; adopting better roofbolting machines; and developing adequate secondary reinforcement technique. The authors believe that this development work together with the on-going wok in other aspects of gaterosd rockbolting, as discussed in this paper 9 represent the rational strategies for the application of rockbolting technology to a wider range of longwall gateroads in Chinese d mines .

Jan 1, 1997

By M. Karmis

Underground mining will disturb the natural equilibrium of the rock mass, causing significant stress redistributions in the vicinity of the excavation with corresponding horizontal and vertical displacements. Subsidence of the ground occurs when these displacements propagate from the mine opening, through the overlying strata, to the surface. Such ground movements may take either of two general forms: a sudden and sometimes violent collapse, or a more gradual and progressive ground movement. The former, characterized by localized failure of roof or pillar in old, shallow room and pillar workings, is rather unpredictable and difficult to analyze. As a result, most control measures are directed toward the latter type of movement, which is associated with the fracture and flow of the strata overlying longwall and high-extraction room and pillar systems, resulting in horizontal and vertical strains in the affected area. Such ground movements can often cause considerable surface disturbances ranging from simple land settlement to severe structural damage. Due to the increasing incidence of this phenomenon in more populated areas and the rising awareness of the problem, it has become necessary to establish a balance between the development of mineral resources and the protection of the environment and society. This paper presents a summary of the major findings derived from a substantial research effort on mining subsidence carried out, during the past few years, in the southern Appalachian coalfield. The research program encompassed the following major tasks: identification of the most significant factor influencing ground movements above mined openings, collection of subsidence case studies for the southern Appalachian coalfield, development of subsidence and strain prediction techniques for that region and initiation of a subsidence monitoring program in southwestern Virginia.

Jan 1, 1984

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013

By Andre Zingano

It is known that the backfilling confinement increases the pillar strength and also reduces the rib lateral displacement. With backfilling, it is possible to increase the room-and-pillar mining recovery. This paper aims to study the behavior of coal pillars confinement using rock fill as backfilling material. Laboratory tests were carried out to determine the behavior of backfilling materials. Constitutive models were developed for the tested backfilling materials. Numerical simulations for the effect of backfilling materials on the ground stability in room-and-pillar coal mine entry were performed. The backfill method is a good strategy to (i) improve the ground stability in room-and-pillar coal mines for long term, especially for weak coal seams, (ii) increase the coal mining recovery and (iii) reduce the quantity of waste material on waste piles at the surface.

Jan 1, 2011

By Kot Unrug

The selection of tensioned versus non-tensioned roof bolts, for primary coal mine roof support, has been debated for well over 25 years. The wide spread use of fully grouted rebar marked the beginning of the discussion of the relative importance of bolt tension and the resultant immediate roof compression. The focus is on roof conditions encountered in coal mines however the discussion may be extended to hard rock mines as well. The theoretical bases for both systems are presented, with the analysis focused on the bolt's ability to actually fulfill the theoretical assumptions. Of specific concern are assumptions about bolt tension upon installation and the likelihood of maintaining useful bolt tension over time. The usefulness of tension roof bolting is limited by the mechanical interaction of roof bolt assembly and the rock, which may be valid at the time of installation only. Ambient mine atmosphere and fluctuation in moisture content changes the physical condition of rock, which may have a significant impact on the effectiveness and longevity of bolt tension. Changes in the material properties of the surface of the immediate roof can invalidate the assumptions, which were made in the design stage of roof support system. This means that the roof support in the long term excavations may be inadequate requiring costly rehabilitation. The presented arguments are illustrated with the examples of some relevant experimental data. Tension primary roof bolting is recommended where the immediate roof is: ? Stiff with a high modulus of elasticity ? Surface layers are continuous and fairly thin ? Not easily weathered

Jan 1, 2004

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992