Search Documents

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By C. A. Pryor

The aggregates industry is the largest minerals industry in the United States producing over 2.6 billion metric tons of crushed stone, sand and gravel annually. Approximately 5% of that production is fine material, passing a 75-micron mesh sieve. Of that amount, about 77% is not sold and represents one of the major industry issues. The material accumulates in stockpiles and settling ponds having an operational and economic impact on the site’s bottom line. Many factors cause this material to be produced: from blasting and processing techniques all the way to end use specifications.

Jan 1, 2002

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By Roderick Eggert, Dipesh Dipu

We look at the empirical evidence of coal block auctions in India to understand how competitive intensity affects the bid amounts in common value auctions. The results suggest that competitive intensity measured through the number of bidders for a coal block is instrumental in determining the bidding outcomes. The presence of higher numbers of bidders in the auction leads to higher bids - every additional bidder causes the bid amount to rise by INR 142.67 per tonne of coal for auctions studied for 127 coal blocks from 2014 to 2023. The paper also examines the moderating and mediating effect of competition on bids and on excess of bids from the comparative market price of coal from alternative source of Coal India Limited. The results indicate that competitive intensity does not have statistically significant impact on the relationship between common value of coal blocks and bids, neither as a moderator nor as a mediator. The strategic behavior of the bidders has also been observed as bidders have been seen to bid in a higher than market price in order to outbid the competitors.

Feb 1, 2025

By A. D. Davis, C. J. Webb, C. S. Johnson

The Belle Eldridge Mine is an inactive lead-zinc mine in Spruce Gulch south of Deadwood, South Dakota. Acidic mine drainage (AMD) produced at the site drains into Spruce Creek, a tributary of Whitewood Creek. The site is on U.S. Bureau of Land Management (BLM) property. Extensive fieldwork was done at the Belle Eldridge Mine through the cooperation of the BLM and the South Dakota School of Mines and Technology. The site was extensively mapped to identify physical and environmental hazards such as tailings, waste rock, collapsed buildings, adits and workings. An exhaustive search of the historical records of the Belle Eldridge Mine was conducted. Maps of the under-ground workings of the Belle Eldridge dating from the 1930’s and 1940’s were found. The maps were used to correlate currently collapsed features to old adits and tunnels. Using hand corers and a portable drill rig, waste rock, tailings and soil core samples were collected and depth to bedrock was determined and the total volume of waste and tailings pile were determined. Related work examined the hydrology of the site. The site is very complex hydrogeologically. Numerous underground and surface workings and tunnels add to the complexity. Several seeps are located at the site, one of which is producing AMD. Recharge to the site was studied, and a 100-year flood plain map was produced.

Jan 1, 2000

By Mark E. Emerson

1967 will be remembered as the year the world realized it was running out of silver. In May of this year a new era in tin the history of the white metal was begun as the power of the U.S. Treasury to regulate world .silver markets was staggered by one of the most intense speculative flurries in recent times. In the past few months the price of silver has risen from $1, 29 to over $1.80 per troy ounce and with it have spiraled the prices of a host of silver-bearing consumer items. Legislation has, been enacted to conserve our coinage and meager silver stocks and today large quantities of non-existent silver are trading hands at a fast pace on the commodity exchanges throughout the world. Now that the price of silver has been set loose, forces are in motion to dull the world's appetite for silver. At the same time there is strong incentive to provide greater quantities of silver to satisfy the world's hunger' for the metal.

Jan 1, 1967

By W. A. Mathews

We report on the progress of an automated mineralogical deportment of fluorine (F) in two portions of the Grasberg District for the development of metallurgical amelioration protocols for Cu sulfide concentrates. Fluorine detection limits in automated SEM technologies range from 1% (TIMA) to about 9% (QEMSCAN), however substitution in hydrophobic minerals or those reporting to concentrate is typically much lower (

Mar 2, 2022

By V. Rajaram

R.K. Leininger, N.R. Hasenmueller, and D.D. Carr The content of the paper by V. Rajaram does not fulfill the expectations of the title. But Rajaram submitted the article in October 1983, and he could not have foreseen the numerous developments that would occur before his paper was published more than two years later. Nevertheless, Rajaram failed to mention the interest in oil shale development in southern Indiana beginning in late 1979 and continuing through the present as a result of special financial encouragement of three oil shale projects in May and August 1984 by the Indiana Energy Development Board and the Indiana Corp. for Science and Technology. A session at the 1985 Eastern Oil Shale Symposium in Lexington, KY, Nov. 18-20, 1985, gave the current status of oil shale developments in the eastern United States. Speakers at this session reported on the three Indiana projects. First, Gary D. Aho, Cliffs Engineering Inc., spoke on a feasibility study by Cliffs Engineering and Allis Chalmers for a site-specific pilot plant using the Allis Chalmers process. The plant site is in Clark County, IN, on property of the Midwest Energy Resources Co. The project is funded by $240,908 each from the Indiana Energy Development Board/Corp. for Science and Technology (EDB/CST) and the US Department of Energy (DOE) and $120,454 from the corporate sponsors (total $602,270). Completion is scheduled for mid-1986. Next, Edwin M. Piper, Stone and Webster Engineering Corp., discussed the American Syn-Crude/Indiana Oil Shale Project. This effort followed the completion of two smaller projects funded by the Indiana EDB/ CST: "Testing of Indiana Oil Shale in a Petrosix Pilot Plant" (total funding by EDB/CST at $50,000) and "Assessment of the Petrosix Process for an Indiana Shale Oil Plant" (total funding by EDB/CST at $100,000). The status at the time of the report at the Oil Shale Symposium was that a request for an extension of time for securing nonfederal support had been submitted to the US Synfuels Corp. The proposal included building an 11-m (36-ft) diam retort in southeastern Indiana to process the New Albany Shale and to produce 366 m3 (2300 bbl) of shale oil per day by the PETROSIX process. The Indiana EDB/CST had contracted with Stone and Webster at $401,100 from EDB/CST and $245,835 from Stone and Webster for activities to advance the project in the negotiations with Synfuels Corp. At the time of the report, this project was the only eastern oil shale proposal that was still on the agenda of the Synfuels Corp. As a result of Congressional action in late December 1985, federal support from the Synfuels Corp. is no longer possible. Finally, Victor H. Carr, Eastern Shale Research Corp., described his firm's project, which is jointly supported by DOE ($227,749) and the Indiana EDB/ CST ($73,850) and is entitled "Feasibility Study to Determine Suitability of an In-Situ Process to Recover Hydrocarbons from Eastern Shale." An area in Scott County, IN, had been chosen, but not a specific 9 x 15-m (30 x 50-ft) site. One burn of a small in situ retort is contemplated as part of the project. Besides these three projects, several reports on shale research were presented. Joseph Damukaitis, American Syn-Crude Corp., reported that a pilot plant using the hydrogenation-extraction (H-E) process (described at the 1984 Eastern Oil Shale Symposium) was 94% built and would go through shakedown with oil shale but would then shift mechanical devices to process coal mine waste. Current status of research on the HYTORT process was then presented by Raymond C. Rex, Jr. Oil shale beneficiation research at the University of Alabama/Minerals Research Institute was reported by R. Bruce Tippin. Scott D. Carter discussed continued research on fluidized-bed retort¬ing of shale at the Kentucky Center for Energy Research Laboratory. Carl E. Roosmagi of DOE, Morgantown, reported on the oil shale research at the Morgantown Energy Technology Center (METC) laboratory. Henry J. Gomberg, Ann Arbor Nuclear Inc., discussed "Radiation Combined with Donor Solvents for Extraction and Up-Grading of Kerogen." Aurora M. Rubel and coauthor Eileen Davis presented results of research at the Kentucky Center for Energy Research Laboratory under the title "The Effect of Shale Particle Size on the Products from the Bench Scale Fixed Bed Steam Pyrolysis of Kentucky Sunbury Shale." Lastly, Maria Rockwell, Technical University of Nova Scotia, presented "Processing and Up-Grading of Low Grade Nova Scotia Oil Shale for Potential Use." A review of shale oil prospects by Gerald Parkinson in Chemical Engineering for Feb. 3, 1986, covers both western and eastern projects and includes a report that the US DOE is funding a few relatively small projects; most of the fiscal 1986 budget of $12 million for shale oil is for fundamental research. Projects include a $3.2 million three-year contract with Hycrude Corp. (Chicago) for development of the HYTORT process and a $1.2 million three-year contract with the University of Alabama's Mineral Resources Institute on beneficiation of eastern oil shale by froth flotation. The report incorrectly states that current projects include a total investment of $466 million in a pair of 18-month technical and economic feasibility studies for proposed projects in southern Indiana. The correct figure is $468,657 [$240,908 for the Cliffs Engineering/

Jan 10, 1986

By W. F. Visser

The growing availability of information and data analysis capabilities of recent years provides new opportunities for improving the performance of mining operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits rapid evaluation of changes and fast business improvement decisions. This article presents a blueprint for alignment of systems, organizational design, and management practices to leverage these developments in performance-driven operations management in mining and mineral processing. The first component of the blueprint is a performance framework with a system of key performance indicators for production control that can be used across organizational levels. This system places improvement at the core of management activities, giving greater importance to improvement skills at lower organizational levels, so companies can leverage available information for improving operational control. Secondly, the blueprint defines an organizational structure that strengthens performance improvement with technological and change management capabilities. Finally, the blueprint proposes alignment of management practices, covering the optimization of short-interval controls, the application of an improvement project portfolio management system that determines the ownership of improvement projects, and the coordination of controls across the organization. This combination of systems, organizational design, and management alignment supports rapid decision-making at the right organizational level. Introduction of the presented blueprint for operations management enables mines to leverage the developments in information and analysis capabilities to improve the performance of operations.

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014