Search Documents

By Daiki Takano, Naoki Takahashi, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"The method in this study, in which cement-treated piles are installed into the ground to decrease the amount of liquefied lateral flow, has been studied. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. In their investigation, they propose shifting the position of the piles to prevent lateral flow in various directions. The present study conducted centrifuge model tests to clarify the improvement effect of piles against the lateral flow of liquefied soil and the effect of the pile arrangement. Then, numerical fluid analyses were conducted to consider the improvement mechanism. As a result, the model tests and numerical analyses showed that the pile improvement dramatically reduced the lateral displacement and that the average total flow velocity decreased in the irregular case.INTRODUCTIONLiquefied ground subjected to seismic motion loses its stiffness and strength, and lateral flow often occurs in sloping areas and backfill areas behind collapsed quay walls. In the Hyogoken–Nanbu Earthquake in 1995, the reclaimed island that was surrounded by collapsed quay walls expanded toward the sea and the amount of displacement reached a few metres (Hamada et al., 1996). Two countermeasures can be considered to guard against lateral flow: preventing liquefaction and reducing lateral displacement. The former method is ideal; however it is costly and time-consuming. Based on these considerations, the authors (Takahashi et al., 2013; Morikawa et al., 2014) are currently studying a method in which cement-treated piles are installed into the ground (see Fig. 1) to decrease the amount of liquefied lateral flow. The countermeasure cost using this method is relatively low because of the low replacement ratio. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. It has been proposed that the position of the piles should be shifted so that lateral flow can be prevented in various directions, as described in Fig. 2."

Jan 1, 2015

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By Cen Guoji

The foundation of bored pouring concrete pile have been adopted in the bridge engineering of China since early in the sixties. They demonstrated tremendous technical advantage and achieved notable economic benefit. With improvement of bridge technique including construction technique work equipment, design theory, examination in quality and applicable range etc, the pile diameter became bigger and the foundation changed from shallow to deep-water. This paper examples Jiujiang Bridge of Guangdong in China, which is single-tower cable-staged bridge, total length of 1675m, and expouds adopted successfully the foundation of variable section large bored pile (upper part d=3m, central part d=2. 4m and lower part d=2m) on the conditions of complicated technique that the load is tremendous (it require specially to resist 12000 kN ship impact) and the piles have free length 30m. The paper will be to describle design project and construction practice of pile foundation with variable section, and to compare schemes of equal section pile and pile in sinking-well.

Jan 1, 1991

By Nathan Iverson, Allie Brady

Located on rolling bluffs on the Zumbro River's south fork in Southeast Minnesota, Rochester is the state's third largest city and is the home and birthplace of the renowned Mayo Clinic, a nonprofit academic medical center focused on integrated health care, education and research. Mayo Clinic employs more than 4,500 physicians and scientists with another 58,000 administrative and allied health staff across three major campuses: Rochester, Minnesota; Jacksonville, Florida; and Phoenix/Scottsdale, Arizona. Originally developed as a stagecoach stop, Rochester has become a national destination for medical care, drawing more than two million visitors annually to Mayo's Minnesota location. Since January 2022, Veit & Company has been working on the construction of the Mayo 1st Ave Tunnel, which comprises three tunnels (pedestrian, utility and services), and the RMC Loading Dock projects in Rochester. These adjacent projects are on the Mayo Clinic's ever-expanding campus and represent its continued dedication to improvement and advancement as a leading medical service provider in the industry.

Jan 1, 2023

By G. Stuart Littlejohn

In spite of recent concerns in certain European countries, I believe that silicate-ester grouts will continue to be employed in practice, unless more cost-effective inorganic grouts are developed for the treatment of fine sands. It is also noteworthy that over the past 40 years, there has been a record of good experience where silicate-ester grouts have been used in ground improvement. Nevertheless, there is now a need via the European Standard EN 12715 (2000) "to assess the environmental impact, particularly the toxicity of the grout and grout components, and their effect on ground and drinking water should be considered before grouting." "When testing the grouting material for environmental impact, the following aspects should be considered: ? Whether during processing, transport or grouting, substance can be generated or released which could be hazardous to the environment or the grouting crew; ? Whether noxious substances can spread upon mixing with ground water; ? Whether reaction products can be produced or released which influence the water quality; ? The type of particles eroded from hardened grout; ? Chemical reactions between hardened grout and the ground water."

Feb 10, 2003

By Robert Small, Amshu Chappa, Ihab Allam

The Biosolids Digester Facilities Project (BDFP) is located in southeast San Francisco. The jobsite is bounded by active Caltrain and Union Pacific Railroad tracks on the west side and the existing Southeast Treatment Plant (SEP) on the north, south and east sides. The existing SEP was constructed in the 1950s and portions of the facility have reached their operational life. The $2 billion BDFP will replace and relocate the outdated existing solids treatment facilities with more reliable, efficient and modern technologies and facilities. In addition, the nearby Bayview and Hunters Point neighborhoods will benefit from the improved odor control. MWH/Webcor, a joint venture, as the construction manager general con- tractor (CMGC) for the project. As part of an alternate delivery method set forth in the prime contract, the CMGC was permitted to propose the use of a core trade subcontractor partner for the SFPUC's approval to provide precon- struction services. The CMGC identified three major scopes (electrical, mechanical and foundation) where a core trade partner would be able to assist

Jan 1, 2023

By Avi Shonberg

With the advancement of offshore wind farm projects towards deeper waters and larger wind turbine generators, founda- tion solutions other than the monopile have received increasing attention over the past 5 years. Monopiles are the most commonly used foundation solution for offshore wind turbines, with 82% in European waters founded on monopile foundations (EWEA, 2019). However, 2018 saw a record number of suction bucket jacket (SBJ) structures, which consist of a three-legged jacket sup- ported by a suction bucket at each leg (Figure 1), installed for offshore wind. applications. SBJs have now been installed successfully at the Borkum Riffgrund 1, Borkum Riffgrund 2 and Aberdeen Bay offshore windfarms. Suction-installed foundations, referred to in this paper as suction buckets, suction caissons, suction piles or suction anchors, have been widely used in the offshore industry since the early 1980s for a range of offshore applications predominantly as anchors for floating offshore structures - where they are "the most widely used anchor types for deep-water mooring applications" (McCarron, 2011). Suction buckets, installed using pumps that generate suction forces by creating a pressure difference between the inside and outside of the bucket, allow for the installation to be undertaken with minimal noise and without the use of mechanical force. Therefore, a key difference between suction-installed foundations and other foundation types is that the installation design, which must consider the soil type, soil strength and installation specific risks (for example, soil stratification with significant differences in permeability) may have a direct influence on the dimensions of the foundation. While the number of SBJS installed for offshore wind applications has increased significantly in recent years, the installation process for SBJ struc- tures is yet to become standard practice and is considerably more complicated than the installation process for mon- opiles. This paper provides a brief

Jul 1, 2022

By J. Erik Loehr, Andrew Z. Boeckmann

"Poor drainage is a common cause of poor performance of earth retention systems, resulting in burdensome serviceability problems that can progress to outright failure of the retention system if not addressed. A drainage system consisting of filtered conical drains that can be installed through the face of an existing retaining wall and readily maintained was evaluated through tests of physical and numerical models. The physical models were constructed with different backfill materials in a container measuring 8 ft wide by 4 ft tall by 15 ft long. Tests were conducted by saturating the backfill under a constant water elevation atop the model, and then maintaining the water elevation until seepage from the drains reached a steady state condition. Pore pressures within the backfill and outflow from the drains were measured to facilitate calibration of numerical models that accompany the physical models. Results from the calibrated finite element models were used to develop design criteria for the drains. The design criteria establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain.INTRODUCTIONMany retaining wall performance problems are a result of poor drainage of the wall backfill. Consequences of poorly drained backfill include displacement and rotation of the wall face, including the extreme case of collapse, and seepage through the face of the wall, which is in turn associated with damage from corrosion, dry rot, and other forms of deterioration. A common approach to improve drainage of an existing wall is the installation of drainage features (e.g. “weep holes”) in the face of the retaining wall. Weep holes facilitate controlled seepage through the face, which relieves water pressure within the backfill and directs seepage to known locations in the wall face. Although installation of weep holes is relatively common, engineering methodologies for selecting the size (diameter) and spacing (along the wall) of facial drainage features are uncommon if not altogether non-existent. This paper documents tests of physical and numerical models of retaining walls with facial drainage features, including conventional weep holes as well as maintainable drains installed through the face and extending into the wall backfill. Results of the testing were used to develop generic design criteria, which establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain."

Jan 1, 2016

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By W. Morgan NeSmith

The city of Kansas City, Missouri, is replacing its original airport, con- structed in 1972 as a "drive-to-the- gate" facility, with a modern, single- terminal facility with just over 1 million sq ft (92,903 sq m) in area along with an adjacent 6,300-space parking structure. It is the largest infrastructure project in the city's history. The project team designed and oversaw the installation of 12-24 in (305-610 mm) diameter augered cast- in-place (ACIP) piles to a range of depths with the pile toes located in underlying alluvial clay, weathered shale or on intact limestone, depending on the required loads at each column location. The specific ACIP piles used were auger pressure grouted (APG) piles. Additional information regarding the ACIP pile installation process can be found in the Augered Cast-in-Place Pile Manual, Third Edition (2016) prepared by the DFI Augered Cast-in-Place and Drilled Displacement Pile Committee. This article includes a summary of the subsurface conditions, the foundation support requirements, the extensive performance test program - started before production installation but not completed until well into production phase of the project - and the resulting production pile installation require- ments. The approach resulted in about $700,000 in foundation program savings to the city. The reduced con- struction time of about 10% less than originally estimated also added to the overall savings beyond the direct foundation savings.

Oct 1, 2022

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015

By X. L. Chen

The diaphragm walling has been recently adopted in one of the largest excavation of deep foundation engineerings in Shanghai, China with dimension of 90m in length, 50m in width and 13m in depth to solve its stability problem. In this paper the field test for monitoring the stability of the diaphragm wall is discribed, in which the excess pore water pressure and the horizontal displacement of the clay layers were monitored during the period of the excavation. The data measured in the field test are efficient for the safety during construction.

Jan 1, 2010

By D. A. Ponniah

The installation of a pile is considered analogous to the expansion of a cylindrical cavity of a diameter equal to that of the pile. Using Vesic's theory of the expansion of cavities the effect of soil properties on pile installation loads, radial pore and total pressures are evaluated. The theoretical results are compared with load and pressure measurements made in field trials in a stiff clayey glacial till in the U.K.

Jan 1, 1987

By S. Y. Zhou

Excavation with earth retaining is one of the main technological means in deep foundations and underground engineerings. Several construction methods which have been used in China are introduced here with some examples from engineering practices in Shanghai, including foundation pit protected by steel or RC sheet piling or D-walls, open caissons and pneumatic caissons, shield tunnel and pipe jacking, etc. This paper also discusses the prospect in development and utilization of underground space in China and the challenge to which the engineers specialized in deep foundations have to face.

Jan 1, 2010

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Hajialilue Bonab M.

The soil-pile interaction under lateral impact loads is not yet completely well known. Many tests on single piles under static lateral loads in centrifuge have been performed and P-y curves have been determined at different levels of the pile in soil. Following these static tests on piles, a large program is undertaken with the same piles submitted to impact loads. The pile equipped with various pile caps has been impacted under variable amplitudes of shock. The behavior of the pile under different impacts was studied and dynamic parameters of the soil-pile system have been determined. Many cases of loading constituting various load histories have been analyzed. They are resulting from parametric centrifuge tests run out, on the one hand with constant and cumulative impacts and on the other hand, variable and cumulative ones. The Influence of each type of loading was studied. Using a finite element method, a non-linear pile-soil system was conceived and a transient dynamic analysis have been performed. The results of the non-linear analysis and experimental data were compared giving a good agreement.

Jan 1, 2002

By H. Cheng

The Bohai Oil Company has applied all together 11 jack-up oil drilling rigs (movable platforms) (1) which can be classified in terms of their forms of foundations into two types: the integ­ral mat and the column legged, as demonstrated in figure 1. Figure 1 a) indicates the entire structure of the sunk cushion type, i.e. the one with a box-like sunk cushion serving as its foundation by directly sitting on the sea bed. The length, width and height of the outer sides for the sunk cushion stand at 45.8 x 38.0 x 3.3m ( for Rig Bohai No.2 ) and 50.6 x 33.2 x 4.88m ( for Rig Bohai No.6 ), the relative areas of theirs being 1475m2 and 2008m2 respectively and both bigger than the plane areas of the rigs. With a view to realize a convenient drainage of mud while sinking, two holes of 14 x 14m and 32 x 18m in size are constructed in the center part of the sunk cushion. When work sets off, the underside of the sunk cushion operates as a foundation, the sunk cushion being connected to the platform by hull columns which transmit the load of the platform down­wards to the sunk cushion that passes it further onto the subgrade. [ ] Column legs for rigs may also be grouped into two categories considering their features: columns with and without boots. The bodies of boot columns are made up of trusses, whose bottoms, are boot-shaped with a big diameter. The diameter of boot columns of the rigs applied by the Bohai Oil Company shows bigger and it may reach 12 or 18m. In the boot columns, the transmission of the platform's weight into soil is done by the underside areas of boots. While in the case of the vertical columns, which are of cylinder columns of steel with sealed bottom ends shaped inverted arch, the entire drilling platform is supported by the carrying force delivered by the bottoms of these steel cylinders and the frictional force rendered by their outside walls. Such a type of columns is featured by a small diameter, 3m in general. Figure 2 exhibits the schematic diagram of sections regarding the two types of column legs.

Jan 1, 2010

By Todd Nottingham

Channel deepening of major ports is challenging designers to explore innovative solutions to ensure stability of bulkheads, such as for the Oakland Inner Harbor. This particular challenge was met with the use of the SPIN FIN® Tension Pile for restraint of an HZ combination wall along the Oakland Inner Harbor Shoreline in Oakland, California. A SPIN FIN pile is a pipe pile with welded plates at the pile tip that increase pile capacity. A brief history of the project will be provided as well as results of pile load tension tests, pile strain gauge, and wall deflection under construction loads. Tension pile load deflection results will be discussed with recommendations toward establishing deflection-based ultimate load criteria. A discussion of predicted wall loads and field observed wall loads will be provided.

Jan 1, 2008

By X. Y. Hou

The design practice of several circular underground projects with large diameter is summarized. By taking the advantages of load-bearing of circular structure, a rational annular tensile bar support system and a new design method are proposed. Calculation for a car park shows that remarkable results are brought in by this design technique.

Jan 1, 2010