Search Documents

By Kevin R. Johnson, Matt Caskey, Bryan Plaskett

Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical design and construction. These challenges can include constrained sites with limited access and laydown area, vibration concerns for adjacent structures, and the need to complete work within limited schedules. When challenging geotechnical conditions like variable bedrock elevations are present, the need to balance performance requirements with logistical constraints become the driving factor when selecting deep foundation systems. This paper focuses on the deep foundations used for a new elevated pedestrian bridge at a major health care facility in Tampa, Florida. In addition to the technical design requirements, the owner required a deep foundation system that could offer low vibrations, rapid production, and clean installation to limit impacts on their properties and the public roadway that separated them. The paper describes the project specific geotechnical and design conditions, describes Ductile Iron Pile design, and focuses on how installation of the system addressed the unique logistical challenges. In addition, the implementation of a full-scale load testing program to assess compression, uplift, and lateral design capacities is presented. This paper represents one of the few published references for Ductile Iron Piles on projects in the United States.

Oct 1, 2022

By Brenton Cook, Daniel Mageau, Larry Applegate, Aaron McCain

"Ground freezing was successfully used to create an impermeable barrier wall along 3,000 feet of the downtown Seattle waterfront as part of the Seattle Seawall Replacement Project. This $360 million re-development involved removing the original 1930-era seawall and replacing it with a new, seismically resistant concrete wall supported on fill soil improved by jet-grout. The replacement wall was one of the largest construction projects in the state of Washington at the time. Ground freezing is typically used as both a structural shoring wall and groundwater cutoff. However, at this project it was used primarily as a cutoff wall to stop groundwater seepage into the 16-foot deep excavation from the landside areas.The project was divided into ten boxes (sections), each typically 200 to 600 feet in length. Only a few boxes were under construction at one time to reduce the impact on tourist-dependent local businesses. Soil conditions in the freeze zone consisted of sand, gravel and silt fill with abundant wood and debris. Tidally influenced groundwater, much of it contaminated, was difficult and expensive to control using wells during initial stages of construction. For all subsequent stages, a frozen soil wall extending to about 35 feet in depth was used to stop groundwater seepage into the excavation. An additional benefit of ground freezing included elimination of potential settlement beneath nearby buildings, utilities, and the Alaskan Way Viaduct that would likely have occurred with the use of conventional dewatering wells. The frozen soil wall crossed more than 130 buried utility locations (including water, sewer, storm, electrical, fiber optic, phone, gas, steam) with no damage. The frozen soil wall was very successful and limited groundwater influx from the landside to the seawall excavation to a negligible amount so that pumping, storage and treatment of contaminated groundwater was essentially eliminated."

Jan 1, 2016

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By Chris Normand, Paul Volpe, Eric Wey, Howard Perko, Burt Ogilvie, Patrick Murray

"A refinery expansion project for Marathon Petroleum Company in Southern Louisiana required existing medium to large pipe racks to be expanded for additional capacity. Foundation modifications were necessary in order to add levels to the existing pipe racks. New piles were added and existing pile cap foundations were expanded. Several different pile types were considered. Custom designed large diameter helical piles were chosen, because they can be installed quickly with low overhead restrictions, produce minimal soil spoils, and are cost effective. The load capacity required for piles was higher than typical, off-the-shelf helical piles. In particular, the lateral load capacity demand was high due to wind loads of a hurricane prone region. Methods used to design and size helical piles are summarized including capacity to torque ratio estimation for composite helical piles. Pile load testing was performed in order to confirm design capacities of the helical piles under axial and lateral loading. Measured axial and lateral deflections compared well with predicted values. This case history evaluates the effectiveness of modern helical pile design methods within the context of a real and practical example.INTRODUCTIONAs the capacity of modern installation equipment increases, large-diameter helical piles are being used to support higher loads in more diverse applications. Currently, large-diameter high-capacity helical piles are used for electrical power transmission, power generation, high-rise buildings, bridges, and industrial applications. This case study regards a 2.5-mile pipe rack modification project within an existing refinery. One of the many challenges for engineering and construction of refinery revamp projects is determining how to effectively expand the capacity of existing foundations for additional equipment, piping, and other facilities. Custom designed large-diameter helical piles provided an effective solution to the challenges faced when expanding the capacity of existing pipe racks."

Jan 1, 2017

By Martin B. Hudson, Kenneth S. Hudson, Gwendolyn Arreguin

A twin high-rise project site in Century City posed several foundation engineering challenges for the design team. One portion of the twin high-rise project site was required to utilize top-down construction in order to allow a driveway to remain open during construction of the project’s 40-foot deep excavation. The challenge was compounded by the need to utilize a mat foundation to support the high-rise construction and yet have temporary drilled shafts through the mat foundation area that would not create excessive differential settlement. This was accomplished by constructing a deck supported by eight drilled end- bearing drilled shafts with Osterberg load cells and five 7-foot-diameter end-bearing drilled shafts. The Osterberg load cells served to verify the capacity of each of the drilled shafts and preload the soils at the drilled shaft tips. The 7-foot-diameter shafts were constructed with bond breakers to prevent skin friction but instead mobilize end bearing (for settlement compatibility with the surrounding mat foundation). After the drilled shafts were placed, then top-down construction began beneath the driveway, leaving the driveway supported on the drilled shafts. Construction challenges included drilling of the shafts through previously abandoned tieback anchors from an adjacent parking structure basement, as well as cemented layers within the rock materials. The paper describes the use of the various analytical methods used to calculate capacities and check settlement compatibility, the construction and testing methods utilized, and the construction challenges encountered. INTRODUCTION Wood Environment and Infrastructure Solutions, Inc. (hereafter referred to as Wood) performed a geotechnical investigation for the New Century Plaza currently being constructed in the Century City District of Los Angeles, California. The New Century Plaza project consists of the construction of two new towers (designated as North and South Buildings) and the rehabilitation of the existing Hyatt Regency Century Plaza Hotel. The existing hotel tower is 15 stories in height above the existing grade and is underlain by four subterranean basement parking levels. The new North and South Buildings will stand approximately 46 stories in height above the existing grade to accommodate residential use. The new towers are planned west of the existing hotel. The site was previously occupied by the existing hotel subterranean parking structure and overlying podium structure, and a loading dock in the southwest portion of the site. The former western portion of the podium and subterranean parking structure west of the existing hotel building western edge were demolished to allow for new subterranean levels, a new podium structure, and the new towers. The lowest floor of the proposed subterranean level required excavation on the order of 35 to 80 feet.

Jan 1, 2019

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Christopher Sammon, Nicholas Turus

"The demand for underground parking in South Florida has increased as a result of changes to the local building code, coupled with developers’ desire to improve building aesthetics and provide much needed walk in retail space for high-end structures. Historically, underground construction was uncommon in South Florida due to the high groundwater level and porous soil/rock. Conventional dewatering methods become ineffective only a short depth below the ground surface and deeper excavations have required a tremie seal solution consisting of wet excavation and the pouring a temporary unreinforced slab under a water head. However, as excavation area and depth increase, the cost and schedule of the tremie seal method become problematic. For these reasons developers and construction teams alike have looked to contractors in South Florida for alternative means of construction.This paper details the construction of two sites in South Florida where Deep Soil Mixing (DSM) technology offered an efficient alternative to tremie seal construction. The Brickell City Centre required excavation of 8 acres to depths of 30 feet, and augercast piles up to 36” diameter and 110 feet in depth. The second site, Jade Signature, required an excavation of up to 41 feet directly adjacent to the Atlantic beachfront. Due to the concerns over differential settlement, the project featured a soil mixed gravity wall that was designed and installed to allow for completion of the tower prior to excavating the adjacent garage.Both projects involved improving every square inch of ground beneath the planned project excavation. The developed DSM seal slab solution creates a nearly impervious excavation at excavation invert with the strength to resist hydrostatic uplift forces. Low permeability site perimeter walls are constructed to complete the sealed excavation and reinforced with either beams or sheet piles for structural support. Augercast piles required for the permanent hydrostatic concrete slab supplement the uplift capacity of the DSM. After DSM and augercast piles are installed from grade, the site is excavated in dry conditions."

Jan 1, 2017

By Partha Sircar

"For Berth 22 modifications at the Port of Oakland, nearly 600 octagonal 24-inch ‘diameter’ precast-prestressed concrete piles were driven, some piles over 160 feet long. Prior to production pile driving, an indicator/test pile program was performed, which included extensive use of dynamic load testing with (Pile Driving Analyzer (PDA) & CAPWAP analyses. The indicator test-pile program resulted in requiring significantly longer piles than the original design based on subsurface borings. The cause of this discrepancy is investigated in light of the available geotechnical information, soil mechanics principles and standard techniques for pile capacity computations. Several interesting phenomena emerged. These include relatively low resistances offered by crushed rockfill than would conventionally be assumed, non-homogeneity of an apparently uniform formation and the effects of jetting on pile side friction. Also revealing was the significant increase in capacity between 1 and 3 weeks of driving for long piles in clay. Recommendations were developed for pile capacity for future use as “lessons learned”.IntroductionThe foundation for the replaced Berth 22 structure at the Port of Oakland in California involved driving approximately 570, 24-inch octagonal precast prestressed concrete piles. A plan and a section for the pile locations are presented in Figure 1.The ultimate loads on the piles used in the design are presented in Table 1 – the loads are quite heavy.The foundation design was followed by an extensive Indicator Pile Program. The contractors (Manson Construction Co. of Richmond, California) opted to use a Delmag D62-02 diesel hammer (Rated Maximum Energy – 165 kip-feet). Per the project specifications, the same hammer was used for both indicator and production pile driving. The production piles of appropriate lengths were ordered based on thr results of the Indicator Pile Program. A number of interesting results were found from the Indicator Program, which is discussed in this paper."

Jan 1, 2015

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Steve Davidow, Ashely E. Evans, Peter M. Kandaris

"Annually thousands of deep foundations are constructed across North America supporting high voltage transmission line structures. However, a recent state of the practice survey by the Deep Foundation Institutes’ Electric Power Systems Foundation Working Group discovered that the electric power utility industry lacks consistent foundation design guidelines. The survey identified a wide variability in design assumptions, a minimal understanding of risk based analysis, and a need to standardize design methodologies. This paper summarizes the state of practice in electric system foundation design and proposes a framework for risk-based foundation design by accounting for uncertainty from both loads and resistances. Loads derived from electric system codes do not necessarily provide a compatible level of reliability for the design of foundations, as they are a mixture of probabilistic and deterministic values. Load uncertainty is derived from variability in weather conditions, structural models and material properties, typically accounted for by code derived overload factors. Resistance uncertainty arises from variability in natural soil properties, resistance models, subsurface construction techniques, material sampling methods, and limited observations. A consistent methodology is offered relating nominal resistance capacity (strength) to structure loads and service state criteria. Discussion also includes the need for risk-based assessments to account for non-structure load influences (fluvial loads, scour ground loss, liquefaction, etc.).INTRODUCTIONNearly 40 years ago the Electric Power Research Institute (EPRI) embarked on a major research effort to optimize reliability and economics of transmission line foundation design. Strategies focused on improvements in design models, site characterization, exploration strategies and testing to reduce uncertainty and variance in analysis. Transmission line engineers realized that safety and reliability advancements in design based on probabilistic approaches, with a focus on the unique nature of transmission line, could better control risk and cost.Some transmission line professionals took full advantage of these advancements, particularly where research led to improved software and models. Yet, even after two decades of extensive research, by 1995 the industry still had made little progress in changing design habits. The majority of designers were still characterizing sites via deterministic methods, using loads that may or may not relate to a consistent probability of occurrence, and applying a traditional global factor of safety approach (Phoon, et al. 1995). The following two decades have seen even greater developments in software and reliability-based analysis methods, but old habits seem to die hard as recent surveys show less than half of design professional quantitatively assess risk in their design process."

Jan 1, 2017

By Chiranjib Sarkar, Sibapriya Mukherjee, N Kumar Pichumani

With the rapid expansion of urban transportation systems, tunnels and cut & cover structures are considered as the only solution in improving the urban space congestion problem in mass rapid transit system. Therefore, it is necessary to accurately design underground structures with realistic assumptions and considerations of design parameters like site geotechnical data, water table, surcharge load etc. Over conservative approach provides not only uneconomical design but sometimes it also causes overdesign of the concerned structures. Water table depth has a significant role in some design aspects of underground structures like floatation check, lateral and uplift pressure on the buried structure, etc. In current practice of tunnel and cut & cover structure design, water table is assumed to coincide with the ground level. Most of the Design Basis Reports & Outline Design Specifications directly mention consideration of water table at ground level for floatation check and load calculations, etc. However, the actual scenario is different in most of the cities specially in northern, central, western and eastern regions of India except the coastal cities. In the present study an attempt has been made to carry out a parametric study on the effect of water table depth in the design of a typical 6.3m outer diameter circular tunnel with 6m backfill. In this study, it is also attempted to establish an analytical method of calculating the most realistic consideration of water table depth instead of the present hypothetical assumption of considering water table to coincide with the ground level. The findings of the current study may be helpful to the researchers and practising engineers in design of tunnel and cut & cover structure for subways and metros.

Nov 1, 2022

By D. Barber, A. D. Miller, P. A. Bray

The project was to develop an area within the existing West County Wastewater Treatment Plant which would enable the construction of a new Raw Wastewater Pump Station (RWPS) with a footprint of approximately 85 feet by 190 feet and a foundation depth of about 82 feet below grade and a new Short- Term Detention Basin (STDB) with a footprint of about 80 feet by 130 feet and a foundation depth that varied from approximately 3 to 24 feet below grade.. The excavation support system had to be designed to withstand both normal and the 100-year flood elevations. A Reinforced Soil-Cement Wall (RSW)was chosen to provide a hydraulic barrier which consisted of a single row of soil-cement elements installed along the perimeter of the area to be excavated. Steel wide flange beams were installed on 4 foot centers to support construction loads and be resistant to the lateral forces of the soil and hydrostatic pressures. The RSW was installed to a maximum depth of 104.5ft using a triple-auger drill rig with mixing paddles with a 2ft key into weathered shale providing a cutoff wall consisting of 53,150 square foot of treated soil. The project was to provide the initial design of the excavation support for the pumping station excavation support system and groundwater cutoff. There was 534 linear foot of soil-cement-bentonite wall installed and 106 - 80 foot long W21 x 121 wide flange beams installed on four foot centers into the alignment of the wall. Each element was drilled down into the weathered shale to obtain groundwater cutoff. Derek R. Guthrie Water Quality Treatment Center Pumping Package is the site for a new pumping station that will service Louisville, Kentucky residents. After unplanned long term exposure into the winter, the effects of freeze thaw cycles were evident.

Jan 1, 2017

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Yan Lap J. Kan

"A waterfront stabilization system consisting of Deep Soil Mixing (DSM) columns, vinyl sheet pile fascia, and concrete flood walls supported on shallow footings was designed and constructed for a high-density waterfront development in Northern California. The project site is underlain by soft, compressible organic soil locally known as Bay Mud that has been capped with loose sand and imported fill. The waterfront stabilization system constructed at the site mitigates liquefaction, consolidation settlement and seismic potential slope deformation along the waterfront; the system was designed to reduce lateral displacements to tolerable amounts for the proposed structures. This paper presents the general design methodologies, construction challenges and quality control of this waterfront stabilization system.INTRODUCTIONUrban development in Northern California is fueling innovations in geotechnical engineering as more complex sites are developed. ENGEO Incorporated introduced a deep soil mixing technology from Japan to the US and designed a waterfront stabilization system for a high density waterfront development project in Redwood City, California. The approximately 12½-acre project site, as shown on Fig. 1, is surrounded by water on three sides, with an inner marina at the center of the site.The project site is located in the seismically active San Francisco Bay Area in California. The San Andreas Fault, the Monte Vista-Shannon Fault, the Hayward Fault and the San Gregorio Fault are major active faults located within 25 miles of the site. Once a former marshland with a major slough until the late 1950s, the site was reclaimed by placing imported fill over the native compressible clay deposits, locally known as Bay Mud."

Jan 1, 2016

By Justin Lukens, Di Stasim Jeffrey, Frank Di Salvo

Columbia University’s Manhattanville Campus expansion includes the construction of two new business school buildings. The new buildings require development of an entire city block bound by 12th Avenue, W 131st Street, W 130th Street and Broadway in Upper Manhattan. A support of excavation (SOE) package was first released, followed by a foundation package. The SOE package consisted of approximately 100 soldier piles and 280 anchors, up to 215’ long, to support a cut anywhere from 30’- 50’ below street level. The foundation package alone included approximately 1600 drilled micropiles. Given the breadth of the work scope, Hayward Baker Inc and Moretrench joint ventured on these two projects to bring sufficient knowledge and work resources to complete the work in an efficient and timely manner. This included working with the Owner/Engineer to propose different means and methods for construction to significantly reduce the schedule while meeting the design intent, such as large diameter (36” diameter) augercast piles in place of conventionally drilled soldier piles and large hollow-bar micropiles (103/51 bars) in lieu of pressure-grouted micropiles. The anchors, ranging from 3 to 22 strands, were used for earth retention through both soldier pile and lagging walls and existing slurry walls. These anchors were complicated based not only on their size and length, but also the need to drill some of them under the historic Studebaker building. The overall magnitude of the project with considerations to resource management and material lead times will be addressed, highlighting critical strengths provided by the Contractor to ensure project success. The scope of work discussed in this paper was executed under two separate competitive bid contracts. The first contract included the support of excavation work and the second contract included the foundation package. The support of excavation comprised of drilled soldier piles (performed by Case Foundation as a subcontractor to the JV), driven soldier piles, driven sheet piles, hollow bar tiebacks, multi-strand tieback anchors and micropile soldier piles. The foundation package consisted of drilled micropiles. Due to the large scope of work and critical schedule requirements of the project, the JV had to think outside the box and present value engineered alternates to expedite installation durations.

Jan 1, 2019

By Patrick Granitzki, Alicia Plinio, Janitha Batagoda, Peter Howell

The City of Newark is making a comeback with new mixed-use multi-storied Residential Development projects. The majority of developers tend to use driven H-pile deep foundation systems to support their super-structures. A different approach was recommended for one particular new development near the Passaic River. The surficial geology included glacial deposits consisting of loose to dense sand overlaying relatively soft silt and clay and a lower stratum of medium-dense sand. During a preliminary site investigation for the project, bedrock was encountered at depths ranging between approximately 168 feet to 182 feet below the ground surface. Design capacity required a single pile of 200 tons. Two different pile foundation systems were evaluated in conjunction to the typical driven H-pile system in order to review potential costs and construction schedule impacts. The two alternative pile systems evaluated were tapered tube piles and drilled displacement piles. Theoretical calculations were followed by in-situ load testing. The field testing results indicated the use of drilled displacement piles as the best option for a portion of the proposed building. This paper discusses the different piles systems considered, installation and using drilled displacement piles to minimize cost and optimize construction.

Sep 8, 2021

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Eric Lindquist, John Compagnone, Gabriel Carvajal

"Condon-Johnson & Associates, Inc. (CJA) with the assistance of design consultant, Brierley Associates, designed and installed a water tight shoring system utilizing several ground improvement techniques jointly. Prior to the installation of the shoring system, a test program consisting of the installation and testing of 7 jet grout columns; 1 soil mix panel; 7 soil anchors and 3 tie downs was performed to verify design assumptions. State-of-the-art quality control measures were employed throughout the project.The shoring system consisted of:•,Deep Soil Mixing (DSM) wall utilizing triple axis tooling to install overlapping columns along the perimeter of the proposed excavation to a treatment depth of 54 feet.•,Installation of steel piles in DSM to provide rigidity to the wall.•,Installation of a jet grout bottom seal, installed from surface to a depth of 58 feet below existing grade.•,Installation of 153 soil anchors, 1-1/4” diameter and 47’-6” length, to tie the jet grout bottom seal to the native soil below to resist hydrostatic uplift, installed from existing grade to a depth of 91 feet.•,Installation of walers and pipe struts for internal bracing•,Installation and stressing of 117 tie downs, 1” diameter and 16 ft length, to tie the pump station mat slab to the jet grout bottom seal, installed from inside the excavated pit.Subsurface conditions at the site consist of uncontrolled fill materials to a depth of 20 feet comprised of sandy silt and clayey sand. The native soils underlying the fill generally consist of soft and compressible lean clay and silt with varying amounts of sands to a depth ranging from approximately 44 to 54 feet below ground surface, which in turn are underlain by dense to very dense silty sand. The groundwater elevation at the site is approximately 8 feet below ground surface.This paper covers the design aspects, construction, and quality control measures undertaken by the geotechnical contractor, with supporting figures.INTRODUCTIONThe owner, County Sanitation District No. 2 of Los Angeles County, designed upgrades to their existing Long Beach Main Pumping Plant Facility. The upgrades consist of a new pump station that includes a reinforced concrete below-grade wet well and dry well, a two-story operations building, two 78-inch diameter pipe inlets, two 42-inch diameter discharge pipelines connecting the existing manifold, two pipe junction structures, two insert-type junction structures, and electrical transformers. This paper focuses on the excavation shoring for the new pump station. The original shoring design concept for the pump station excavation illustrated on the contract plans consisted of pressed in sheet piles, a jet grouted bottom seal with soil anchors, 2 levels of internal bracing, and tie-down anchors to resist hydraulic uplift forces on the buried pump station."

Jan 1, 2017

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021