Search Documents

By A. C. du Preez

The separation of nickel and cobalt from calcium, magnesium and manganese by solvent extraction using synergistic mixtures of carboxylic acids was studied. Addition of certain viable synergists to commercially available tertiary branched carboxylic acids, such as Versatic 10 (Shell) or Neodecanoic acid (Exxon), produced large synergistic shifts (?pH50) in the pH50values for nickel, and small antagonistic shifts (negative ?pH50values) in the extraction of calcium. Under the initial test conditions used (0.50 M each of Neodecanoic acid and the Mintek synergist, in xylene) a large separation (pH50Ca? pH50Ni= 3.09 pH units) between nickel and calcium in their extraction from 1.00 M sodium nitrate solutions was obtained, compared with only 1.11 pH units in the absence of the synergist. The selectivity series for the extraction of divalent base metals from 0.333 M sodium sulphate solutions by 0.50 M Neodecanoic acid and 0.25 M of the Mintek synergist in C12-C13aliphatic diluent was found to lie in the order (with pH50values in parentheses): Cu(3.42) > Ni (5.08) > Zn (5.58) > Co (5.73) > Mn (6.62) > Ca (7.48) >Mg (8.25). In batch counter current experiments, a simulated leach liquor containing (in gL-1): Ni 5, Mg 5, Mn 2, Co 0.5, Ca 0.5, Cu 0.1and Zn 0.1 was contacted with the mixed extractant in three stages at unit phase ratio and an equilibrium pH of 5.9. The recovery of nickel was 99.9 per cent and that of cobalt was 84.7 per cent, whilst the co-extractions of manganese, calcium and magnesium were 2.7,1.5 and 0.04 per cent, respectively. The recovery of cobalt can be enhanced by employing a slightly higher pH, although this will also increase the extraction of manganese, calcium and magnesium somewhat. Nearly quantitative stripping (99 per cent) of nickel from the loaded organic phase was achieved in a single contact at an organic-to-aqueous phase ratio of 4 using a simulated spent electrolyte containing 39 gL-1sulphuric acid and 33 gL-1nickel,thereby producing an ?advance electrolyte? containing 57 gL-1nickelat pH 3.5. Loading of acid into the organic phase was very slight, amounting to only 0.002 M H+in contact with the above-mentioned spent electrolyte. Keywords: solvent extraction; synergism; nickel; calcium; carboxylic acids.

Jan 1, 2004

By N. Sahay

Improvement in work place environment by conventional methods viz., installation of higher capacity fan, fans in parallel operation or booster fan is a risky proposition in many coal mines in India because of difficult geo-mining condition such as shallow depth, multi seam workings having thin parting and inter connected goaves one above the other. The situation is further worsened if the mines have fire affected sealed off area connected to different ventilation circuits. On many occasions circulation of more air quantity by increasing fan pressure have resulted in initiation of spontaneous heating. To address these problems, authors have made some improvement in conventional Dynamic Balancing of Pressure Technique and worked out few ventilation schemes which are aimed for neutralization of pressure differential across sealed off area at the same time having improvement in ventilation in the mine. The excess pressure differential across sealed off area is mainly caused by introduction of higher capacity fan. Similar situation prevailed in one of the mines of Jharia Coalfield, India. The problem was solved by application of the above technique. In this paper, brief description of the technique, the problem in the mine, results of investigation, computer simulation studies of various schemes and methodology adopted for implementation of the technique in the mine have been discussed in some detail. Keywords: Dynamic Balancing of Pressure Technique, Spontaneous heating, Work place environment.

Jan 1, 2003

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By F. Peer

In most coal preparation processes, water is a necessary medium, but the presence of water in coal after it has been cleaned has a negative impact on transportation costs, handling and specific energy values. The utilization of super absorbent polymers (SAP) in the nappy application is well known. The concept of utilizing these polymers was investigated for the purposes of dewatering coal and other fines, generated by preparation processes such as flotation. SAPs are granular highly cross-linked synthetic copolymers with excellent water-absorbing properties. The dewatering process is characterized by three main stages: (a) contact of super absorbent polymer with high-moisture fine coal; (b) separation of dewatered fine coal from super absorbent polymer; and (c) regeneration of used super absorbent polymer, by exploiting its response to changes in conditions such as pH or temperature. Preliminary tests showed the separation step to be very difficult. The novel idea of encasing a given amount of polymer in a water permeable cloth solved this problem (of separating the swollen polymer from the dewatered coal). Preliminary tests investigating the effectiveness of the sachets of polymer showed a drastic decrease in the moisture contents of slurries. Furthermore, it was shown that it was possible to regenerate the polymer (still within the sachets) through thermal drying. A full-scale experimental programme was then followed to accurately determine the feasibility of using sachets of SAP. The experimental variables were initial slurry moisture content and polymer dosage. It was observed that the sachets seemed to work fastest and most effectively at high moistures and also at higher dosages of SAP. Regeneration of the polymer was also investigated, using two methods: thermal regeneration and pH-induced regeneration. The experimental variables, for investigating the regeneration process, were method of regeneration and grade of water used. Thermal regeneration at 70°C seemed to work successfully. Although the cost of using thermal energy is still a problem, the safety aspect (fire hazards) has been addressed since the polymer does not ignite when heated, unlike fine coal particles that may do so. The alternative method of regeneration, which exploits the pH-sensitivity of the polymer, was less successful, and further work needs to be conducted.

Jan 1, 2003

By J. A. Bakken, G. Sævarsdóttir, H. Pálsson, M. Þ. Jónsson

The role of the electric arc in the consumption of electrodes in submerged arc furnaces has long been debated. The hostile environment in the furnace does not make direct measurement feasible, so simulation has been used to evaluate the arcs contribution to the erosion. Magnetofluiddynamic (MFD) electric arc simulations and a cathode / anode sub-model developed in order to provide boundary condition to the arc model have been used for this purpose. The cathode / anode sub-model provides current distributions and cathode / anode fall voltages for the arc and temperature distribution for the electrode surface, which is paramount to the erosion rate which in turn is calculated from the Clausius Clapeyron equation and the Hertz Knudsen formula for the vapour transport. In the case of high-current industrial AC arcs, arc currents are typically ~100 kA, phase voltages ~100 V and total furnace power ~10 ? 60 MW. The results show that although enormous amounts of material is evaporated, much of it recondenses on the surface. Furthermore the results show that the arc erosion increases strongly with the arc current. If a single arc is present its contribution to erosion is close to the actual total erosion in the furnace. Results from this analysis indicate that there are possibly more than one arc present in the crater, in which case less than 40% of the total erosion would be due to the arc, the rest is chemical erosion.

Jan 1, 2007

By R. J. Forzatti

The production of sulphuric acid from sulphur generates heat. The majority of this heat is recovered as steam and is often used to generate electricity. Heat not recovered as steam is rejected to cooling water systems. The design of the turbine, condenser, and cooling water systems impacts the overall water, energy, and environmental footprint of the plant. This review considers a conceptual 2000 t/d sulphuric acid plant with several alternative cooling water systems. The review utilizes Hatch?s 4 Quadrant sustainable design tool to compare the alternatives on both an economic and a weighted sustainability scale.

Jan 1, 2014

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By G. Broadbent

It is an honour to be invited as a speaker to this ICCR conference and a pleasure to be with you here in South Africa. I have been asked to talk about the competitiveness of coal versus other energy alternatives. Coal supplies nearly one-quarter of the global primary energy. Its most direct competitors are gas, nuclear and renewables. Oil is predominantly for transport fuels. Fuel oil is competitive with coal when crude is below its long-run average price and has some niche opportunities. But I will confine my comments to nuclear, renewables and particularly natural gas as the most potent current competitive threat to coal. Competitiveness is more than just cost and price; there is environmental acceptability, security or reliability and increasingly image. These factors are more of a spectrum than discrete issues. Dollars and cents remain the key issue for competitiveness but one must recognize the impact of politics in sustainable development and energy security.

Jan 1, 2001

By D. M. MacHunter, T. Lawson, D. K. Henderson

The development and commercialization of new generation high tension electrostatic separators has provided a basis for simplifying mineral separation plant circuitry. The inclusion of new design features including insulated plate electrodes that have resulted insignificantly improved separation efficiencies in electrostatic separators are described. The increase in separation efficiency has resulted in a reduction in the number of treatment stages required to produce final high grade mineral products. Comparative performance data on different feed types are presented. A comparison between mineral separation plant flowsheets using both conventional and new generation high tension electrostatic separation technology is presented. A 55% reduction in the number of installed electrostatic separators and a 36% reduction in plant area was achieved through the use of this new electrostatic separation technology.

Jan 1, 2003

By S. Sarac

Solving ventilation networks of natural splitting is a basic problem in mine ventilation. Several mathematical techniques are used to solve this problem. This paper proposes a new method which combines the advantages of both classical Hardy Cross method and unconstrained optimization techniques. The trials carried out on model networks have shown that the method offers some facilities in the analysis of mine ventilation networks. Keywords: Ventilation network analysis, Hardy Cross method, Steepest Descent method.

Jan 1, 2000

By E. Yalçin

The data set often contains one or more secondary variables. These secondary variables are usually spatially cross correlated with the primary variable. The addition of the cross-correlated information reduces the variance of the estimation error by using the cokriging method. The grade estimation results of ordinary kriging and cokriging methods are evaluated and it was found that the estimation variance of cokriging method is slightly lower than ordinary kriging. The effect of variation of block dimension on the estimation results is also investigated and it was seen that the cokriging estimation variance values also decrease as the block dimension increases.

Jan 1, 2005

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Immediate Past President J.R. Dixon Junior S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2000

A mining engineer from South Africa, whose research has taken him to some of the world?s deepest gold mines, is the winner of the St Andrews Prize. Daniel Limpitlaw, 27, picked up a cheque for $25,000 for his dissertation on reversing the damage done by early mining technology, which he claims is partly responsible for blighting the urban environment in many South African cities. Launched in October 1998 by the University of St Andrews and international energy company Conoco, the St Andrews Prize sought practical solutions to environmental problems. It attracted interest from 450 individuals and groups from countries as diverse as China, Pakistan, Canada, New Zealand, Germany, the UK and the United States.

Jan 1, 1999

By B. Elevli

The aim of this paper is to demonstrate the implementation of multicriteria analysis in selection of the most suitable underground ore transport system for a chromite mine in Turkey. The related problem includes five possible ore transport systems and six criteria to evaluate them. The adopted evaluation and ranking method for this study is PROMETHEE. PROMETHEE I revealed a partial order of alternatives where incomparability exists. PROMETHEE II gave the absolute ordering of alternatives. The results have shown that the PROMETHEE method can be successfully used in solving mining engineering problems. Keywords: multi-objective, decision analysis, mining, ore transport system

Jan 1, 2004

By I. Ewart, E. Roux

Skorpion Zinc operates a solvent extraction/electrowinning zinc plant producing over 150 000 t/a of special high grade (SHG) zinc (>99.995% Zn). In the current flow sheet copper and cadmium are cemented from the neutral leach solution using zinc powder, to prevent galvanic corrosion of plant equipment and build-up of copper in plant solutions. This process is effective but unfortunately consumes expensive zinc dust and produces a low value copper product. The EMEW® (Electrometals electrowinning) technology of Electrometals Technologies Ltd. uses a rapid flow of electrolyte through a cylindrical cell to deposit copper or other metals from dilute solution (less than 1 g/L) [1]. The copper can be deposited as powder or may be harvested as a tubular cathode product. The advantage of the use of EMEW® technology at Skorpion Zinc will be to eliminate the use of expensive zinc dust and to produce a high value copper product for sale. Following extensive bench test work, a piloting campaign was carried out at Skorpion Zinc. The tests demonstrated the ability of the EMEW® cell to effectively remove copper from solution through direct electrowinning at lower operating cost than cementation. Keywords: Skorpion Zinc, copper, cementation, direct electrowinning, EMEW®

Jan 1, 2007

By S. Sarac

In this study, a statistical model is suggested in order to determine the methane emission from a working seam. In the proposed method, methane concentrations which are systematically measured in return airway are the sample values, and the calculated statistical parameter is the upper confidence limit of the average of these values. At any given time, the probability of methane concentration in the return airflow to be lower than the calculated upper confidence limit value is 97.5%. The statistical method has been applied to the panel 206 of Armutcuk Mine, Turkish Hardcoal Enterprises. The calculated methane emission value for the considered shift was 15.18 m3/t.

Jan 1, 2003

By A. A. Smithen

There is an increasing awareness of the importance of including an assessment of environmental liabilities in the preparation of bankable feasibility documents. This means that environmental assessments of proposed, existing and decommissioned mine sites have to be undertaken for the purposes of quantifying environmental liabilities and assessing potential risks. This paper examines the need for considering environmental liabilities before describing the approach adopted in undertaking due diligence studies for the preparation of bankable feasibility documents and some of the difficulties experienced. Finally, some concluding remarks are made and the implications for the mining industry are discussed.

Jan 1, 1999

By P. K. Sahoo, C. R. Ray, S. S. Rao

This paper deals with various factors affecting the strength of chromite briquettes which plays a vital role in the smelting of charge chrome / ferro chrome production. Appropriate briquetting parameters like molasses and lime binder level, molasses quality, particle size distribution and segment condition etc. are essential to guarantee quality briquettes in the successful use of briquette and chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the grain size characteristics of the chrome ore fines but also to make an informed choice of the type and quality of the binder and the condition for producing a physically and chemically competent green and cured briquette. This paper also describes the effect of strength of briquettes on various parameters of charge chrome production as the use of quality briquettes in the production of high carbon ferrochrome alloys has a number of operational, metallurgical and economic advantages. It is also a requirement for submerged arc furnace operation that the charge be adequately porous to allow gaseous products of the reduction reaction to escape from the furnace charge burden without hindrance. Otherwise, furnace material would erupt causing electrodes and furnace other equipments damage and risking the safety of the work force. The briquette, because it replaces lumpy charge but has an advantage of smaller size, allows for an uniform and porous charge so that the ascending gaseous products can escape freely. Finally this paper deals with furnace operational results with varying proportion of briquettes having same strength.

Jan 1, 2007

By H Zimba, S Sondashi, M Chitambo

By the time a reagent is finally accepted by a mine for use on its plant it could have gone through several screening and evaluation stages. These stages may include laboratory and plant evaluation testwork. This paper outlines the steps that were followed to select, design and implement a frother for KONKOLA COPPER MINES PLC Nchanga Copper Concentrator in Zambia. It discusses initial frother screening work conducted at the Betachem metallurgical laboratory and the subsequent laboratory screening testwork conducted at Nchanga Concentrator. A modified Bikerman test method is discussed which was used to design a frother for the Nchanga flotation plant. The paper also gives an account of several plant scale trials conducted on Nchanga flotation plant and discusses the plant results, frother consumption patterns and some commercial concerns, before the product was finally accepted by the mine.

Jan 1, 2007