Search Documents

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed-limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and sup-plies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By R. A. Guereca

The Bureau of Mines conducted an analysis to determine criteria for steady-state, laminar flow boundary conditions for a coiled-tube gas viscosimeter by comparing experimental data from a thick-walled, stainless steel capillary in a horizontal, straight-tube condition, with similar data taken after the same capillary was formed into a helix. Overlapping volumetric f10wrates and pressure drops are covered for both configurations at pressure levels of 28, 225, and 1,000 psia at 3000 K. Friction factor, Reynolds number, and Dean number correlation plots show conditions where the coi1ed-tube flow deviates from straight-tube flow. The coiled-tube data indicate departure from Poiseui11e steady-state laminar flow at a Reynolds number close to 390 and a Dean number of about 15. Below these conditions and consistent with the data reported, Dean's circulation appears negligible. For the particular coil used, a conservative upper limit of 10 is chosen for the Dean number corresponding to an upper limit of about 250 for the Reynolds number.

Jan 1, 1967

By P. C. Good

Tungsten metal in fused form and of high purity was prepared by reducing tungstic oxide with redistilled calcium metal in a heavy-walled sealed reactor. Alloys of tungsten with vanadium, molybdenum) chromium, columbium, and tantalum were prepared by coreduction of mixed metal oxides in the same manner. This work was undertaken by the Bureau of Mines to investigate new approaches for preparing tungsten and its alloys in high-purity form. The standard method of producing tungsten metal has been the reduction of tungstic oxides by hydrogen. The resulting metal powder is compacted, sintered, and fabricated by powder metallurgy methods. Long experience in this field has resulted in the development of a technology that (by careful control of the variables such as metal composition, particle size, and sinterng technique) is well adapted to producing wire and the small shapes usually prepared from tungsten metal.

Jan 1, 1961

By D. J. MacDonald

The Bureau of Mines investigated two alternative methods for treating a zirconium-bearing chloride-sulfate strip liquor to obtain reactor-grade Zr02. One method involves neutralization with NH3 and the other hydrothermal precipitation. The strip liquor was derived from zircon sand by a Bureau of Mines method for separating zirconium and hafnium via solvent extraction with a tertiary amine. Neutralization with NH3 to precipitate hydrous zirconium oxide required 0.9 to 1.1 g NH3 per gram of zirconium. The NH3 can be recovered for recycle. Zr02 that met reactor-grade specifications was produced by precipitation with NH3? Hydrothermal precipitation of Zr02 from strip liquor required that the solution be maintained at 2600 C and 680 psi for 10 min and in a non-corrodible pressure vessel. In bench-scale experiments both methods gave-zirconium recoveries greater than 99 pct.

Jan 1, 1984

By D. S. Harper, C. O. Carman

A German coal planer was put in operation in the Keystone mine of the Eastern Associated Coal Corp. , Keystone , W. Va . , in August 1960 . At present , the planer is mining in the fourth panel . The blocks of coal mined were 340 by 1,900 feet in panel 1 , 340 by 1,660 feet in panel 2 , 590 by 1,900 feet in panel 3 , and panel 4 , currently being mined , is 590 by 1,900 feet . Almost one- half million tons of coal have been mined from these four panels . An 11 - man crew handles the complete planer operation and produces an average of 500 tons of clean coal per shift . Self - advancing hydraulic props are used to support the roof over the entire face . Roof control and action on all of the panels has been highly satisfactory . During periods of extreme pressure , some additional support is required in the tail entry where evidence of weight from the retreating longwall extends about 200 feet outby the face . The time lost from production by moving equipment between panels has been reduced steadily . The move from panel 3 to panel 4 required 5 days , but it is believed that even that time could be reduced .

Jan 1, 1963

By D. J. Bauer, V. E. Shaw

Bastnasite concentrate was processed to recover total rare - earth content and obtain high - purity ceric nitrate . Reaction of the concentrate with 45 percent caustic soda for 1 hour at 180 ° C in stainless steel vessels resulted in 99 - percent conversion to rare - earth hydroxides . A drying step followed by solution in nitric acid produced a tetravalent cerium fraction amenable to extraction with TBP . Single- stage separatory funnel experiments resulted in 90 -percent recovery of ceric nitrate at a purity of 99.9 percent . Fractional extraction in pressure - bubbler columns resulted in 98.5 - percent recovery of 99.5 -percent - pure ceric nitrate .

Jan 1, 1964

By David M. Hopstock

To help assure an adequate supply of minerals to meet the Nation's economic and strategic needs, the Bureau of Mines is conducting bench-and pilot-scale research using wet high-intensity magnetic (WHIM) separation to recover iron from oxidized taconites of the. Lake Superior region. The advantages and disadvantages of WHIM separation in relation to other separation methods, the most recent innovations in WHIM flowsheet design, and the role of mathematical models in process optimization are discussed.

Jan 1, 1979

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed- limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and supplies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By R. P. Adams, R. A. Beall

The Bureau of Mines developed a method to melt and cast specimens of hafnium- carbon alloy and studied their properties . A rotating - ladle vacuum or inert atmosphere arc furnace was designed , special electrodes and molds were developed , and operating procedures were worked out for casting small shapes . The cast specimens were evaluated according to their carbon content for melting point , density , microhardness , electrical resistivity , and oxidation resistance . Lattice dimensions were determined , and metallographic specimens were prepared . Photomicrographs were taken of specimens containing 2.72 , 5.50 , 6.47 , 9.97 , 12.8 , and 15.7 weight - percent carbon , and their grain structures were compared .

Jan 1, 1963

By L. E. Dalverny

This Bureau of Mines report describes the deployment, 5-month operation, and lessons gained from a continuous gas monitoring system using sampling-tube bundles at an underground mine fire in West Virginia. Research information gained indicates the utility of relating certain gas concentration ratios to events during fire development, mine reventilation, and mine recovery. In addition to monitoring the quality of remote fly ash seals, the system provided timely warning of dangerous gas concentrations which developed during surface and underground recovery activities. An evaluation of system components is supplemented by recommendations for improvements.

Jan 1, 1975

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956

By W. E. Anable

The Bureau of Mines studied the purification of commercially available yttrium by melting it in a 100-kw electron-beam furnace. Button-scale melts were made to determine the ultimate purification that could be attained by melting yttrium at 1,733° to 1,770° C at low pressure (0.05 to 0.1 micron) for 1 to 120 minutes. In addition, numerous melts were made to study the effect of doping yttrium with carbon, 17 selected metallic additions, and 3 compounds. Except for nickel and zirconium, the metallic impurities in yttrium were lowered significantly on extended treatment; silicon was lowered only slightly. The nonmetallic impurities} oxygen, nitrogen, and carbon, were not lowered except on short exposures. In isolated instances, the oxygen content was lowered from 5,860 ppm to about 5,000 ppm. In most instances the carbon con-tent was lowered from 545 to about 220 ppm in 20 minutes and then increased again. It was concluded that yttrium cannot be purified by direct heating or by the doping technique employed.

Jan 1, 1965

By D. H. Platt

Bauxite, the principal source of aluminum, has been mined from deposits in Saline and Pulaski Counties, Ark., since 1899; war needs have greatly stimulated production. Many of the ore deposits are basin-shaped and either outcrop or are covered by a shallow-depth overburden at their peripheries; these are mined by stripping and open-pit methods. When stripping becomes economically impracticable, incline shafts or slopes are sunk on the dips of the deposits, and underground mining is done on the retreat, using a room-and-pillar method.

Jan 1, 1945

By Lorenz E. Sieffert, Lawrence B. Berger, H. H. Sehrenk, Ralph W. Stewar, James A. Gale

"INTRODUCTION The purpose of the investigation discussed in this article was to evaluate the toxic hazard from gases produced when thermosetting plastic materials used for electrical insulating purposes are burned or thermally decomposed in enclosed spaces. For brevity the term ""toxicity"" is used throughout the article to refer to the nature of gases produced under these conditions. A need for immediate study of the problem was created as a re¬sult of the battle damage reports received from various United States Fleet units. These indicated that the fumes emitted when these materials were burned or thermally decomposed had, in several instances, resulted in toxic atmospheres. In attempting to develop a suitable test method for evaluating toxicity, it was recognized that no single test procedure could be expected to duplicate the variety of conditions that might exist in an actual fire aboard ship. In view of the immediate need, however, it was felt that considerable information could be obtained, at least to classify comparatively the several types of materials as to the toxic effect caused by burning or thermal decomposition, through the development of a sound empirical method which could be applied to all of the materials. On this basis, it was decided to modify the Navy flame resistance test for thermosetting plastics to render it applicable to the determination of the toxic, gases evolved when this test was employed. A wide variety of materials was tested, both molded and laminated, to cover the types commonly used by the Navy in electrical applications. Toxicity determinations were conducted at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Parallel tests, to determine the flame resistance of the materials, were conducted at the Material Laboratory, U. S. Navy Yard, New York, N. Y."

Oct 1, 1947

By W. P. Yant

[At the majority of mines where flame safety lamps are used either as working lights or as a means of detecting gas, no check it made on this condition of the various parts of the lamp and their assembly other than a visual ink inspection. Although this inspection should be made carefully in view of tae serious consequence that may follow Vie use of a faulty lama, In many instances the inspection is of a perfunctory nature. The Bureau of Mines has therefore designed a small box or gallery for testing lamps for defects and improper assembly before they are taken into the mine. The test simulates the condition when a lamp is extinguished by its introduction into an explosive mixture and the operator attempts to relight the wick while the lamp contains the explosive mixture. This test is more rigorous than merely subjecting a lighted lamp to an explosive methane-air mixture. In the latter test the products of combustion tend to blanket the propagation of flame from within the lamp to the exterior, especially if there are defects at the top of the gauzes. Moreover, when the lighted lamp is subjected to an explosive methane-air mixture the methane builds up slowly within the lamp until the lower inflammable limit is attained, whereupon a feeble explosion occurs within. If the nonlighted lamps is first filled with the methane-air mixture that gives the maximum violence and is than ignited, the dampening effect of products of combustion is obviated and the strain on defects is]

Jan 1, 1930

By F. W. Hoertel

Tungsten from the hydrogen reduction of WF was vapor - deposited to coat MERM (Material Evaluation Rocket Motor ) graphite and rhenium- lined graphite nozzles . These nozzles have surface configurations that preclude the conventional fabrication of high- density- tungsten liners . Operation at 550 ° C produced selectively placed uniform coatings of specified thicknesses at near theoretical density . An acceptable coating could not be deposited on a beryllia nozzle because of an undesirable side reaction between the substrate and one or more of the products of the reduction reaction .

Jan 1, 1964

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By A. J. Keast

This circular is one of a series dealing with the exploration, equipping, and development of mining properties, prepared and published by the United States Bureau of Mines in cooperation with various mining and exploration companies in the United States and Canada. This series of papers will supplement an earlier one which covered the methods and costs of mining and milling at a large number of producing mines. The present paper describes the exploration, equipping, and developing of a group of 18 claims remote from rail transportation, and the transport of equipment and heavy supplies for a distance of 120 miles by tractor over ice and winter roads, and of men and lighter supplies by airplane.

Jan 1, 1933

By Fred Kissell

The Bureau of Mines has developed the shearer-clearer--a new type of dust control system for longwall shearers. The system partitions the airflow around the shearer into a clean split and a contaminated split. The dust cloud is confined to the vicinity of the coal face, while the shearer operators remain in the clean split on the gob side of the machine. The shearer-clearer operates on the principle that each water spray moves air like a small fan and can be positioned to direct the dusty air towards the face. The hardware is inexpensive and can be installed in a single shift. It consists of several strategically mounted water sprays and one or more passive barriers. Laboratory testing indicates reductions 1n shearer operator dust exposure as high as 97 pct. Preliminary results from an underground demonstration in one mine also indicate that considerable dust reductions at the shearer may be obtained. In conjunction with the development of the shearer-clearer, dust surveys were conducted in three other mines to determine if some shearer spray systems currently in use partition the flow in a manner similar to the shearer-clearer, and if so, whether this partially accounts for markedly cleaner conditions on some longwalls. Results from these surveys indicate this to be the case. A feature of the cleaner longwalls was a downwind orientation of their water sprays, which is a key element of the shearer-clearer system. The shearer-clearer system described in this report was designed for an Eickhoff EDW 300 shearer working a 7-foot coal seam. The testing to date has concentrated on cutting directions counter to the primary airflow. The development effort continues for different mining equipment and conditions. It is expected that different systems will be required to accommodate the range of conditions occurring underground. Application of the system presented here to conditions different than those described is not likely to produce the same results.

Jan 1, 1981