Search Documents

By E. J. Gleim

In keeping with past custom, it is the purpose of this publication to bring up to date previously published lists of equipment that meets safety standards of the bureau of Mines so that the mining industry may be informed as to the development and availability of equipment that can be used safely. The present lists supplement those in Bulletin 543. Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Equipment Approved During the Calendar Years 1953-54; and Information Circular [40], Permissible Equipment Approved During the Calendar Years 1955-56. These [ew] lists also contain equipment meeting those standards revised since the last listing. A revision of Schedule 16C (now Schedule 16D4/) was officially approved on September 28. 1958. Schedule 29 was another standard revised in 1958. The revision was officially approved on September 8. 1958, and is known as Schedule 29A5/ .

Jan 1, 1960

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By Ruth F. Brinkley

Principle activities of the Bureau of Mines Explosives Research Laboratory from July 1, 1960 to June 30, 1961 are reviewed briefly in Part 1. Part 1 also includes data obtained in connection with several minor investigations which are not sufficient to warrant separate publications. Part 2 gives brief abstracts of publications that appeared during fiscal year 1961; in general, the research reported in these publications antedates this period.

Jan 1, 1963

By T. L. Turner, Daniel T. Rogers

As part of a program to investigate technology for the extraction of studied HNO3 alumina from abundant domestic ores , the Bureau of Mines leaching of calcined Georgia kaolinitic clay . In this investigation , iron impurities were removed from the aluminum nitrate pregnant leach liquor by solvent extraction , and the purified liquor was evaporated to prepare a suitably concentrated crystallizer feed liquor . Aluminum nitrate nonahydrate was crystallized from the liquor to separate the aluminum from undesirable trace elements and excess water . Continuous crystallization at 40 ° C in a pilot plant vacuum evaporative unit was performed for 5 days to observe the effects of impurity buildup under minimum bleed- stream conditions . Liquor feed rate was 26 lb/h and AAll (( NNOO33 )) 33..99HH22O0 ((AANNNN)) crystal production rate was 17 lb/h . Fe 203 and Cr203 were not effectively separated from the crystals , and P205 , MgO , and K20 impurities must be removed by recrystallization . Other impurities did not excessively contaminate the crystals . Washing the crystals with water or aqueous HNO3 gave an equivalent increase in crystal purity levels by displacing mother liquor . Theoretical equations , applicable to any continuous evaporative crystallization of developed to produce material balances for engineering ANN , were applications .

Jan 1, 1965

Argentina follows Venezuela and Mexico as the largest producers of crude petroleum and natural gas in Latin America. Argentina 1S practically self-sufficient in fuels, but relies substantially on imports for its supply of copper, iron ore, ferroalloys, sulfur, and fertilizers. Mining activity is limited and is in an incipient stage of growth, considering the country's potential for mining. Most nonfuel mineral output in 1979 consisted primarily of minerals used for construction, while only 9% are other nonmetallic, and 2% are metallic minerals. Argentina is Latin America's major producer of boron minerals and uranium (yellow cake). Mineral exports consist primarily of borates, uranium concentrates, and of late, some tin. These exports have in the past been shipped mostly to Great Britain. London banks have been involved in arranging financing for St. Joe Minerals Corp. IS planned development of the El Pachon copper deposit (see map), and were being counted upon to also back the development of large copper and manganese projects. The following is a review of Argentine mineral production in 1979: (For 1981, the production of boron minerals is put at 167,000 metric tons and uranium at 300,000 metric tons.)

Jan 1, 1982

By Farrel W. Lytle

Instrumental analysis has become an indispensable tool in research and production of the rare-earth elements. This development can be attributed mainly to a combination of two factors--the marked chemical similarity of the rare-earth elements, which excludes classical methods of analysis, and the speed and accuracy of instrumental-analysis techniques. With continued improvements in methods of producing high-purity rare-earth elements, keeping pace instrumentally is becoming much more difficult. Accordingly, greater emphasis is being placed on improving instrumental limits of detection and accuracy. The methods employed most frequently for determining impurities in rare-earth elements involve use of the optical-emission spectrograph (3, 4)4/ and the spectrophotometer (9). Although numerous X-ray-emission spectrographic methods (6-8) have been developed for analyzing rare earths, these techniques have not included detection of low-level impurities. This investigation was conducted to find the precision and accuracy of X-ray fluorescence in deter-mining impurities in rare-earth oxides in the 0.01-to 1.0-percent-concentration range.

Jan 1, 1959

By M. D. Marshall

A remote heat-activated stench gas/tracer gas mine alarm system was developed to reduce the time between fire detection and personnel notification. The stench gas/ tracer gas system contains ethyl mercaptan for personnel warning and a fluorocarbon for tracer gas detection by instrumentation. A system was also developed which can be interfaced with multiplex mine phones. In-mine tests were conducted and several systems are presently installed in a hard rock mine.

Jan 1, 1983

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By E. D. Gardner

The American petroleum industry is supplying the present domestic demand for liquid fuels. Known reserves of petroleum in the ground, however, are limited, and the .cost per barrel of finding new oil pools is increasing. Any deficiencies of domestic production in the near future doubtlessly could be made up by imports: Dependence upon foreign oil for part of our industrial requirements is not necessarily cause for alarm, but in time of war an adequate, dependable, domestic source of liquid fuels is vital to the defense of the country. As a national defense measure, and to insure a future continuous oil supply for our economic machine, it would appear logical to take steps now to develop methods for producing petroleum substitutes within our own borders. This undoubtedly was in the mind of Congress when it passed the Synthetic Liquid Fuels Act (58 stat.190; 30 U. S. C. Sup. Secs. 321-325), Approved April 5, 1944.The title' of the Law reads: An Act authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes. Congress authorized $30,000,000 for a 5-year program and directed the Bureau of Mines to carry it out. The part of the program pertaining to oil shale is being conducted on Naval Oil-Shale Reserves Nos. 1 and 3 (fig. 1) at Anvil Points, near Rifle, Colo.

Jan 1, 1948

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By Robert L. Grayson, Syd S. Peng

"An airborne dust study was undertaken at a Southwestern Pennsylvania underground bituminous coal mine by the Pennsylvania Department of Mines and Mineral Industries in 1964 for the purpose of making recommendations and requirements regarding compliance with health and safety aspects of The Bituminous Coal Mining Laws of Pennsylvania, approved by the legislature on July 17, 1961. The study was designed to accurately represent the airborne dust conditions of the subject mine. Sampling by midget impinger of specific worker locations throughout the mine was accomplished. Sample analyses yielded dust concentrations to mppcf, particle size determinations in cumulative per cent less than specified cut-off diameters, and determinations of free silica percentages in total dust samples. The data from this study is further analyzed, and the results are presented.INTRODUCTIONThe Bituminous Coal Mining Laws of Pennsylvania, enacted in 1961, prompted a study of respirable coal mine dust by the Department of Mines and Minerals Industry in 1964. In recognition of their obligation for ensuring the health and safety of bituminous coal miners, the department set out to characterize the airborne dust of mines throughout the commonwealth. The purpose of the studies was to make recommendations and requirements for compliance with the law and for control of airborne coal mine dust in Pennsylvania mines.One such study was undertaken at an underground bituminous coal mine operating in the Pittsburgh Seam in Southwestern Pennsylvania. The study was desig11ed to sample specific worker locations throughout the mine site and characterize the respirable dust relative to each of them. A midget impinger was used to gather respirable range dust samples during an 8-hour shift. Continuous miner operator, roof bolter, stoper bolter, loading machine operator, shuttle car operator, gathering motorman, mainline motorman, and rotary dumper jobs were sampled underground. In addition, barge mover, coal sampler, fine coal operator, heavy media operator, and boiler room attendant occupations were sampled on the surface. The surface sampling was over a 71-hour shift because of UMWA contract provisions."

Jan 1, 1988

By R. O. Dannenberg

A metallic displacement process, utilizing easily available steel wool or steel window screen, was devised and successfully used for the recovery of silver from waste photographic fixing solutions. Laboratory and prolonged commercial-scale testing established that the iron filament type unit will efficiently precipitate silver, as a high-grade sludge, from acidic waste photographic fixing solutions ranging in grade from less than 1 to over 10 grams of silver per liter. Data and design information are presented to facilitate the construction and operation of a practical unit of any desired size. A smelting process for recovering pure silver from precipitated sludge containing 27 to 80 percent silver was devised.

Jan 1, 1968

By Willard L. Hunter

The smelting of tin slags was undertaken at the Bureau of Mines Albany Metallurgy Research Center (AMRC) to produce crude columbium-tantalum ferro-alloy as a unit operation in the production of pure columbium and tantalum oxides or chlorides. Columbium and tantalum-rich alloy was prepared during short unrelated campaigns over a total period of 12 years. Tin slags from Malaya and the Congo (Geomines) were smelted. These slags were reduced by carbon in a small, single-phase, steel-making furnace} a larger three-phase, steelmaking furnace, and a three-phase, submerged-arc furnace, In all cases depleted slags were fluid and easily tapped from the furnace. However, unless diluted by iron additions, the metal product was a viscous, high-melting, heterogeneous mixture that could be removed from the furnace only by hand rabbling.

Jan 1, 1966

By R. H. Sprute

The Bureau of Mines conducted a feasibility study and designed an operational system for consolidating waste coal sludge in a 110-acre pond by applying direct current between buried and floating electrodes. Consolidation would reduce the sludge to half its present volume, there-by extending the working life of the pond as well as creating a safe, stable impoundment. The project was conducted by the Bureau under an agreement with the Washington Irrigation and Development Co. (WIDCO), located near Centralia, WA. Part 1 of this report, published as Report of Investigation 8666 in 1982, covers the results of laboratory tests at the Bureau's Spokane Research Center and of a small-scale field test at WIDeO's coal preparation plant. Test results show the process is efficient and cost-effective when power is applied at low current density. Part 2 (this paper) describes a detailed design for an electrokinetic system to dewater WIDCO's 110-acre pond with a 27.4-acre electrode array. Densification of the inactive sludge pond will require 3.6 yr of treatment for a total cost of $1,450,000. The study and design are site specific, but design procedures and analyses are sufficiently detailed to serve as a guide for applying the process to any sludge pond.

Jan 1, 1988

By E. G. Davis, H. P. LeVan, L. S. Smith

Leaching of a Georgia umber ore when using both ferrous sulfate and pickle liquor was studied in the laboratory . The ferrous sulfate content of the leach solution was the major factor affecting the extraction of manganese from the ore . Time , temperature , and the sulfuric acid content of the leach solutions had relatively little effect on leaching of manganese from the ore ; however , these factors did affect the amount of iron extracted from the umber and/or precipitated from solution . Simulated countercurrent leaching of the ore with pickle liquor containing 130 gpl (grams per liter ) ferrous sulfate ( 48 gpl ferrous iron ) produced a pregnant solution having 16 gpl manganese and 41 gpl iron . Filtration tests of the leach slurries indicated that separating the leach solution and solids by vacuum filtration was impractical , whereas pressure filtration was feasible when the cake thickness was limited to about three- fourths of an inch . Fired pellets of the filter cake yielded a firm , hard product analyzing 56 percent iron and less than 0.1 percent sulfur .

Jan 1, 1964

By J. A. Rowland

Magnesium alloys containing nickel, nickel and manganese, lithium, lithium and manganese, and lithium and aluminum were investigated. Melting, casting, and mechanical working techniques and the heat treatment of various compositions were studied. Amenability to cold and hot working was shown for many compositions. The magnesium-nickel and magnesium-nickel-manganese alloys failed to develop superior mechanical properties and were very low in resistance to corrosion. The magnesium-lithium series, although entirely plastic, had low strength properties. The addition of small amounts of aluminum to the Mg-Li base did not affect greatly either the ductility or the strength; further additions developed increased strength, but only at room temperature, and the alloys became brittle with age. Continued study, concentrating on the ductile lithium-rich beta phase as a base composition for ternary and quaternary systems, is recommended.

Jan 1, 1956

By R. O. Dannenberg

This Bureau of Mines report describes the results of research to develop a process for recovering additional beryllium from a commercial mill waste product, fluoferrate leach residue. Forty-five percent of the total beryllium in the leach residue was recovered in a beryllia product assaying over 98 pct Be0 by a process comprising (1) leaching with 1 N sulfuric acid, (2) adjusting the acidity of the leach liquor to pH 2, (3) extracting the beryllium with di-2-ethylhexyl phosphoric acid (EHPA), (4) stripping the loaded extract with sodium hydroxide solution, (5) boiling the sodium beryllate strip solution to precipitate beryllium hydroxide, and (6) calcining the beryllium hydroxide. Calculated reagent requirements per pound of Be° recovered by a proposed flowsheet were 28.1 lb sulfuric acid, 0.04 lb flocculent, 0.15 lb EHPA, 0.06 lb isodecanol (IDA), 0.22 gal kerosine, and 6.3 lb sodium hydroxide.

Jan 1, 1966

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By P. M. Daling

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume II of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 2006