Search Documents

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

Laboratory experiments show that the delay detonators, either electric (copper coated or aluminium) or non-electric (down-the-hole) as generally used in opencast mines and quarries have some scattering from the actual firing time due to manufacturing inaccuracy and variations in basic ingredients of the product. This scattering varies from 1 to 4 % depending on the product quality. Due to this component scatter, adverse blasting effects like misfires, overbreak, underbreak or fly-rock may occur if the design patterns are not judiciously made. It has also direct impact on muck profile and fragmentation.

Jan 1, 1999

By Ekin Güngor, Berkant Ozdemir, Erkan Bayrak, Serdar Ergün, Sedat Esen

"This paper presents the final wall blasting practices at Eldorado Kisladag Gold Mine in Turkey. Benchmark and improved wall control designs were explained in detail. Kisladag Mine has been implementing a high quality slope stability program on-site. The quality of pit walls is generally considered excellent, with very few wall failures being evident and with presplit hole barrels prominent in most areas of the pit. However, a minor scale slope failure occurred recently at the north-east section the pit. A project was initiated to diagnose the cause of the crest loss and evaluate ways to limit its effect on final walls. Final wall blasting practices and geotechnical designs were evaluated. The work presented in this paper showed that changes to the blasting and geotechnical parameters are required atthe north-east section of the pit. Geotechnical design changes were 10 m bench heights with 70 ° slope face angle at that specific area. Having implemented several geotechnical and blast design changes (elimination of the subdrill for the catch bench, appropriate primer location, more favorable blast tie-up and delays), the crest loss was minimized significantly (<1.5 m) (<5 ft)."

Jan 1, 2017

By Scott Orenstein

Construction blasting has allegedly been the cause of property damage in the following situations: (1) When the detonation of the shot hurls rock and debris into the air that causes property damage upon impact; and (2) When property owners notice cracks in their walls and foundations after they experience the momentary vibrations that coincide with the detonation of the shot. The current state of the law for both these situations is firmly established. Blasting is classified as an abnormally dangerous activity, for which the blaster is held strictly liable, whether the damage is the result of flying debris or vibrations and concussions generated by the blast. It is when the alleged blasting damage is supposedly from concussions and vibrations, however, that the courts usually reach the wrong result. The typical scenario involves property owners that thoroughly investigate their property after feeling blast generated vibrations, and find cracks that they believe did not exist beforehand. Most often the truth is that the property owners have never noticed these cracks before because they have never looked that closely before. Any structure has a certain number of cracks due to a variety of causes, such as settlement overtime and temperature and humidity changes.

Jan 1, 2004

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Kagan Ozdemir

In the condition that drilling and blasting technique is inevitable depending on the rock mass and material characteristics on mining activities, the fragmentation rate and particle size distribution of the muckpile after blasting has important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc. and the total costs of that mine. Drilling and blasting is an important step in this process chain and it's results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. There is an increasing body of blasting research indicating significant impacts in these downstream processes.

Jan 1, 2007

By Ron Glowe

This paper shows the potential of a new computer model, using the Glowe-Tech (GT) Tonnage Analyzer program to compare drilling and blasting results. This model uses the crushers and conveyors as measuring tools in aggregate quarries in the USA and Canada. All data is collected using commercially available kilowatt transducers and an analog input/output automation module. There are two areas of measurement used to compare results. The first area is the tonnage moved by key conveyors to show the split in products produced and the actual rate of production. If belt scale readings are not available then the Glowe-Tech Tonnage Analyzer can be used to convert kilowatts from the conveyor motor to tonnage. The second is the tons of rock crushed per kilowatt hour of energy consumption by the primary and secondary (optional) crushers. This modeling process works best if blasts are mucked and crushed in sequence. There are many other variables such as crusher types, crusher settings, screen sizing and actual geology in the pit that can influence the results, however if variables can be standardized then definite trends can be seen when comparing drilling and blasting results

Jan 1, 2005

By Luis Valentim, Terry Cousins

The goal of a mine is to produce ore at the lowest possible cost with due regard to safety of pemonnel and equipment. The mining process consists of a number of discrete operations such as planning, drilling, blasting,excavation, transportation and crushing. These processes are interrelated and cannot be considered as separate activities when optimising output and minimising cost. In order to optimise the global costs it may therefore be necessary to increase cost in one area such as blasting design and management beyond the norm.

Jan 1, 1998

By Paul Sainato

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. A second survey was distributed in 2015 and included international students. This paper provides the data from a third online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2016

By H G. Bosmare, G Bedser, C V. B Cunningham

Peak Quany has achieved substantial improvements to its bottom lie by giving close attention to blasting practice, and in pr@icnlar by introducing electronic delay detonators for routine production blasting. The precision and flexibility provided by these units has enabled the quarry to gain control over fmes and curtail oversize without increasing explosive usage. In addition, the extent of nuisance from blasting vibrations has been reduced.

Jan 1, 1998

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By Vasile Pop, Ovidiu Galca, Constantin Salajan

The paper comprises a brief presentation of the rock fracturing techniques applied in CNMPN “REMIN” Company’s mines in Baia Mare. Parallel are emphasized some shortcomings of this field. The second part of the paper includes our preoccupations and achievements, of the last period, in especially those linked to techno-economical indices improvement resulting from the development of relatively large section mining works and blasting applied with sublevel caving methods.

Jan 1, 2003

By D. J. Goodings, R. J. Bonenberger, H. U. Leiste, W. L. Foumey

This paper describes a series of two-dimensional tests conducted and filmed with a high-speed (500 frames per second) video camera. The purpose of these tests was to provide a better understanding of the processes involved in creating craters and channels in water covered soils with explosives.

Jan 1, 2000

By Bruce Vandenberg, R. Frank Chiappetta, John Foley

Recent advances in solid-state, field portable, fast framing compact video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 4.1 seconds of data can be captured directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the MotionMeter system and compare these with the analogous aspects of film-based cameras and other systems. Of all blast monitoring systems and techniques available today, high-speed motion picture photography and videography still remain as the most valuable, stand alone, diagnostic techniques for troubleshooting and evaluating full scale blasts in the mining and explosives industries. High-speed image data, coupled with information obtained from other instrumentation systems, such as continuous velocity of detonation recorders, laser surveying systems, refraction and ground vibration recording seismographs, etc., can eliminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both excellent and poorly designed blasts is increased, and optimum blast results, (which are application dependent), are achieved considerably faster when compared to the trial and error approach of relying on strictly the experience factor. Applications include developing site-specific blast designs, decay equations relating burden, burden velocity and explosive energy, determining ground response times, reducing coal damage, quantifying backbreak, evaluating the effectiveness of sternming, checking delay detonator firing times, evaluating air decks and for studying general dynamics. Motion analysis is performed with a 2D and 3D software package developed specifically for video analysis, but is also directly applicable to film analysis when using a digitizer. Dimensional controls, lens aberration, field set-ups and camera orientation are all automatically corrected for with matrix analysis.

Jan 1, 2000

By Orica

Unlicking the Possibilities ISEE Digital Detonator Workshop New Orleans, LA Wednesday, February 4, 2004

Jan 1, 2004

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By Robert Martin, Brian W. Stump, David P. Anderson

2We use field measurements to quantify physical processes that accompany different types of mining explosions. The data sets collected include three-component ground motion, acoustic, video and high speed film, three dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions include simple single-fired contained explosions, ones designed to bulk and fracture material and those that cast material. Our goal is a physical understanding of these sources for the purposes of optimizing blasting practices.

Jan 1, 1998

By M. Hokkanen, M. Hagfors

The Finnish Defence Forces has destroyed old and spoilt munitions in open surface mass detonations at Hukkakero fell in municipality of Kittilä, Lapland, since 1988. The technique was learned from Sweden. The destruction camp is organized every year at autumn and it lasts 4-5 weeks. During the disposal period one or two charges are exploded per day. The gross weight of a typical charge varies from 150-250 tons including 15-25 tons of explosives. They mainly consist of TNT, but may also contain smaller amounts of amatol and hexotol. As a booster there have been used 2-3 tons of emulsion explosives.

Jan 1, 2015

By Tjaar A. Louw, Albert P. Van Niekerk, Johannes J. Louw, Attie J. Goosen

Unlike molecular high explosives, commercial explosives based on ammonium nitrate do not detonate ideally according to the theoretical model for steady state, one-dimensional detonation. One of the reasons for this deviation from ideal detonation is the slower chemical reaction, due to less intimate contact between the oxidiser and fuel components. It is well known that the inclusion of gas pockets, such as microballoons, in the formulation of ammonium nitrate based emulsions and watergels enhances the performance of these explosives. Various different interpretations of the “hot spot” theory have been proposed to explain this phenomenon.

Jan 1, 1997

By G K. Jorkenson

Blast designs to cast a percentage of overlying waste rock off coal seams differ greatly from conventional blast designs for surface coal mines. Today, blasting engineers can benefit from computer simulations to test various blast designs and reduce cost and time spent on the old trial-and-error method.

Jan 1, 1989