Search Documents

By Dongwook Kim

Recently, load and resistance factor design (LRFD) is gradually being adopted internationally in geotechnical design due to the advantages of LRFD over the existing allowable stress design (ASD). LRFD is a more advanced design method compared to the ASD because resistance factor is calibrated based on the reliability analysis for a given target reliability index. Target reliability index changes with the importance of the structure. Typically, target reliability index of offshore foundation is less than those of onshore. The widely-used Imperial College Pile (ICP) design method is used for the calculation of pullout capacity of driven piles. The uncertainties regarding pullout capacities of driven piles are assessed using the statistical data reported in the literature. The first-order reliability method (FORM) is used to calibrate resistance factors for the pullout ultimate limit states of the driven piles for three different levels (2.5, 3.0, and 3.5) of target reliability index. The load factors used in this paper are the ones proposed in the AASHTO LRFD bridge design specifications.

Jan 1, 2010

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By William M. Dalrymple, William P. Owen, Benjamin S. Rivers

For the California Department of Transportation (Caltrans), geophysical applications have played an important role as part of a successful multidisciplinary approach to subsurface characterization for the design of high value structures. Since at least the 1950’s, geophysical methods have been deployed to guide the exploration drilling program and to maximize the return on drilling investment by increasing the amount of data obtained from test borings. Geophysical applications saw increased use beginning in the 1990’s, during the seismic retrofit of the state’s toll bridges and the replacement of the west span of the San Francisco-Oakland Bay Bridge. Over the intervening years, increases in computing power and increasingly sophisticated commercial off-the-shelf software applications have allowed Caltrans to leverage advancements and perform geophysical investigations of increasing complexity and scale. Ultimately, the goal of these efforts is to maximize return on investment, whereby increased investigation costs at the design phase are offset by reduced uncertainty regarding subsurface conditions, leading to reduced cost overruns related to change orders and unforeseen site conditions during construction. These objectives are consistent with the recent Every Day Counts (EDC) initiative to incorporate Advanced Geotechnical Methods in Exploration (A-GaME) into routine engineering practice. Caltrans is an implementation partner of the A-GaME initiative, and Caltrans’ practices represent a model toward the institutionalized geophysical site characterization practices for other transportation organizations. The authors provide a retrospective on 70 years of experience with geophysical applications for transportation infrastructure, with examples and observations on potential future direction of the industry.

By Nils Schneider, Marc Peters, Stefan Frey, Andrea Fluck

Due to the worldwide population growth, the development of sustainable infrastructure and the exploration of renewable energies plays a key role to handle the rising megacity trends and to limit carbon footprint. Herrenknecht AG is a leading manufacturer of Tunnel Boring machines and has constantly endeavored through its extensive Research and Development programs to address limitations faced by the civil engineering industry as regards to construction equipment capabilities. New mechanized technologies, mainly coming from the tunnelling industry, have been developed by Herrenknecht AG as an efficient alternative to conventional civil engineering, where tailor-made concepts are required to comply with restricted conditions onsite. Very often this innovation led technology capability has meant making construction processes safer due to minimal human intervention and also far more productive due to higher performance as compared to other latest or conventional methods of construction. The rising need for even higher building structures and large-capacity bridges involve the development of innovative deep foundation technologies for on- and offshore operation. Conventional methods like bore piles reach their technical and economic limits under certain conditions. For building shafts and foundations, the mechanized Vertical Shaft Sinking Machine technology (VSM) from Herrenknecht AG is a proven innovation and has now been used in various onshore infrastructure projects worldwide to construct a total of 94 circular shafts in depths of up to 115 meters. It operates below the groundwater level, completely remote-controlled from the surface in a diameter range from 4.5 to 18 meters. Subsequently Herrenknecht noted that Offshore foundations, especially in non-drivable ground conditions such as soft and hard rock (e.g. limestone, sandstone, mudstone, granite etc. or soft soil with high density) and shallow continental shelf (water depth approx. 20-60m), presented construction challenges and equally an opportunity for building high performance equipment. The latter construction conditions usually requires drilled installation methods for applications such as harbor enlargements, bridge foundations and foundations for offshore wind turbines. The Offshore Foundation Drilling technology (OFD®) is Herrenknecht’s latest innovation, incorporating our learnings from the VSM and full-face Tunnel Boring machines, and the OFD® enables a rapid and economical offshore installation in such variable ground and rock conditions. This paper will discuss the technology behind the new mechanized technology of VSM and Herrenknecht’s latest innovation of the OFD® along with their respective application fields in foundations construction. The paper will further present in details, their range of benefits to the construction industry.

Nov 1, 2022

By Jonathan J. Dewsbury

It is argued that approximate computer based methods are only suited to modelling conventional piled rafts, for pile enhanced rafts where the interactions will be non linear three dimensional finite element analysis is required. However current 3D finite element analysis often relies on symmetry to reduce computational cost and there are concerns over the dependency of the results on the user. Therefore a new strategy within the finite element framework has been proposed. The main advantage of this strategy is that each stage of the model can be checked for consistency. There is also the added benefit that non symmetrical models can easily be constructed by tying the validated components together without dramatic increases in computational time. The proposed strategy compared well to the published results of a hypothetical example of a piled raft previously analysed with numerous methods by Poulos et al. (1997).

Jan 1, 2010

By John C. Niedzielski

The PHX Sky Train is a five mile long automated people mover system located at Phoenix Sky Harbor International Airport. Phase I of the PHX Sky Train includes the design and construction of 227 drilled shafts supporting three stations and approximately 9,000 feet of elevated guideway. The guideway includes a 100 foot high, 330 foot long span extending over an active taxiway, which will be the first system of this kind over an active taxiway in the world. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the guideway above the ground surface, where it needs to pass over existing concourse walkways, bridges, a taxiway and buildings. Drilled shaft design involves designing 4.5-foot to 9-foot diameter drilled shafts within the SGC deposits, most of which extend well below the groundwater table. There is a high potential for collapse of drilled shaft excavation sidewalls within this material. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the guideway and stations. A load test shaft was designed and constructed as a means to provide site-specific measurement of axial performance under these difficult conditions. Results from the load test were used to reduce the size of the drilled shafts. This paper provides an overall description of the PHX Sky Train project, a summary of the ground conditions, design requirements, load test results and construction methods and equipment used to successfully install the drilled shafts for this project.

Jan 1, 2010

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022

By Christopher R. Harris

"Considerations are presented for developing and implementing self-hardening slurry mix designs to be utilized in barrier seepage walls. Slag-cement-cement-bentonite (SCCB) slurries are the primary focus, with some comparisons referenced to the more traditional Portland-based cement-bentonite (CB) slurries. Field and laboratory mixing methods are reviewed, including 1) single sack – single mixer method; 2) bentonite slurry mixer – cementitious addition mixer method; 3) bentonite mixer – grout mixer – CB blending mixer method. Major phenomena associated with the dynamics of barrier wall excavation, such as loss of water from the in-trench slurry and consolidation of in-trench slurry are discussed. Other topics touched upon include sand content effects, fluidizers utilized, and chemical contaminants. The role of higher bentonite to water ratio is reviewed, with demonstration of improvement of filtration properties, and an increase of water retention of the final consolidated product.IntroductionSelf-hardening slurry has been utilized to construct barrier seepage walls for many decades. This is essentially a single-step slurry excavation and backfill process whereby the trench-supporting fluid gains strength over a short period during installation and maintains or develops low hydraulic conductivity. The resulting curing slurry becomes the actual barrier wall as the resultant cement-augmented clay slurry now fulfills the dual purpose of both temporary trench stabilization and final cured-in-place product. This eliminates the requirement and expense of subsequent backfill/slurry displacement operations required in traditional barrier wall installations.Self-hardening slurries have been fabricated using a number of various clays, most commonly sodium bentonite, calcium bentonite, attapulgite, and sepiolite. Perhaps due to plentiful high quality sodium bentonite deposits found domestically, the proven excavation stabilization properties imparted from sodium bentonite slurries, sodium bentonites are typically specified for formulating self-hardening slurries in the US. Cementitious materials utilized most commonly are Portland cement and slag (ground blast furnace slag or GBFS). For the purposes of this discussion, self-hardening slurry having a cementitious of Portland will be referred to as CB. Those having cementitious material of GBFS replacing Portland (partially or wholly) will be referred to as SCCB."

Jan 1, 2016

By Henry Zhang

This paper presents two case studies of large diameter driven tubular steel piles for the ongoing Woolgoolga to Ballina Pacific Highway upgrade (W2B). This project forms part of Australia’s largest regional infrastructure project and will upgrade about 155 kilometers of highway to four-lane, divided road. There are more than 170 bridges on W2B, and driven tubular steel piles are adopted on 43 bridges between Glenugie and Ballina. Driven piles terminating in soil or basalt is a big challenge faced by both designers and piling contractors due to 1) the uncertainty of expected pile unit shaft and base resistance in different soils; 2) whether plugging is formed; and 3) highly variable basalt strength and thickness near top of the rock. If these risks are not adequately managed during design or construction stages, it could lead to unexpected project delay, extra time and cost or pile toe damage in basalt. This paper describes two case studies, one for piles designed to terminate in soils and the other for piles designed to terminate in basalt. How these risks were assessed and managed during detailed design, procurement, hammer selection, pile installation and verification will be discussed in details with lessons learnt summerised in the conclusion.

Nov 1, 2022

By Bradley J. Fleming

Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading. The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface. In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil.

By Jin-Wei Huang, Bradley J. Fleming, Sri Sritharan

"Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading.The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface.In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil,IntroductionPilings are the preferred foundation support for many civil engineering structures including highway bridges, railroad bridges, and port wharves. These structures and their foundations are subjected to forces created by earthquakes, wind, waves, water current, vessel impact, ice, and gravity. All loads applied to the superstructure must be transmitted to the foundation where they are resisted by the surrounding soil. With significant lateral loads, use of pile foundations may be the only solution to transmit large structural loads to competent soils. Piles supported by competent soils are relatively easy to design and costs are often attainable. However, thick layers of weak soils such as soft clays are widespread in high seismic areas (e.g., San Francisco, southern Nevada, Washington, Eastern Missouri, and Arkansas), exacerbating design challenges. Soft clays reduce the lateral resistance of the pile-soil system, making the pile foundation less cost effective. In this case, the current design practice is to use an increased number of larger diameter piles, which is a costly alternative (see SDC, Caltrans 2010). An innovative and more cost-efficient solution to this problem is to improve the soil within a short depth surrounding the foundation, thereby increasing its lateral stiffness. Some well-known methods for improving soil include deep soil mixing, stone columns, and simple soft soil replacement with select granular material."

Jan 1, 2017

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019

By Stuart Coutts

"This paper presents an overview of the author’s experience related to the assessment of the base capacity of straight shafted and enlarged-base bored piles in sand. A design approach based on CPT qc is described which has been calibrated using a database of load tests. The importance of correct installation techniques with instrumentation are illustrated and a discussion is presented on the current use of high strain dynamic testing to validate compliance with design. An example of a recent project with high quality instrumented load test data illustrates the close match to the proposed best practice approach and also highlights the importance for consideration of the effects of stress relief for deep foundations installed in deep excavations.1 INTRODUCTIONContinuous Flight Auger (CFA) piles are the bored foundation pile of choice for sand deposits across Australia. The evolution of the determination of the base resistance of CFA piles has been shaped by available investigative techniques, calculation methods, and calibration of designs with laboratory and field testing. The Cone Penetration Test (CPT) has been widely used in Western Australia (WA) where the test has been commercially available via multiple contractors for more than 25 years. On the East coast, the adoption of CPT testing has been slower with a transition from traditional Standard Penetration Testing (SPT) still occurring. Dynamic pile load tests are often used to derive parameters. The influence of pile installation on performance is commonly misunderstood and is an important element on any discussion of pile capacity for CFA pile types. The interface between the base of the constructed pile and the in-situ soil has an influence on capacity such that a poorly constructed pile base will have limited (if any) contribution to pile performance within the normal working range, generally within a 10 mm movement. The research presented in this paper pertains to CFA piles (no drilling fluids) and enlarged base piles constructed using CFA techniques under drilling fluids such that clean pile/base interface is targeted. Developments in modern piling equipment and instrumentation allow the pressure and volume of delivered concrete/grout to piles to be accurately monitored at various stages of installation such that repeatable ‘best practice’ can be achieved. The changes in soil conditions that occur due to the disturbance of the install technique are also important.Although the results of this research are likely applicable to bored piles, the interface between the pile and in-situ soil (shaft and base) need to be considered for various installation techniques. The effects of stress relaxation (due to removal of soil above pile base and adjacent shaft), time to concreting, and the zone of disturbed soil around the pile shaft are paramount.2 INSTALLATION CONSIDERATIONS The pile mix (concrete/grout) and interface with the in-situ soil are also an important consideration. For example, coarse grained, poorly graded, dry, clean sand will be partially permeated by most pile mixes; such that the influenced soil will be enhanced and in instances the overall effective pile dimensions increased. Permeation of the disturbed zone of a pile or anchor shaft along with scale effects (Lehane 2009) can have significant effect on shaft capacity and shaft frictions significantly exceeding expected are not uncommon based on ‘theoretical’ dimensions. Advancements in mix technology and mix techniques also have a large influence on the pile/soil interface. The ability of the piling rig and augers to excavate a plumb and gauge hole can also have a large influence on the zone of soil disturbed adjacent the constructed pile with a resulting influence on capacity."

Jan 1, 1900

By James P. Chivilo, Gregory R. Meeder, Scott J. DiFiore, Matthew H. Johnson

New construction in metropolitan areas has direct impacts on immediate neighbors and abutters. While noise and dust are generally nuisance concerns, demolition, vibrations, excavation, and dewatering can cause structural damage to adjacent structures. Different cities, states, or jurisdictions have different regulations that dictate requirements, roles, or responsibilities for varying parties during construction. The authors will introduce and discuss risks of new construction adjacent to existing structures, and the legal framework in Illinois which requires the owner of the new construction project to provide adequate protections for adjacent existing structures. The authors, who are engineers and attorneys, will discuss technical and legal concerns, and will highlight the importance of early and frequent communication among project participants to manage risks, despite whether or not any local regulations exist to drive the process. RISKS IN ADJACENT CONSTRUCTION New construction in metropolitan areas inherently involves some combination of noise, dust, ground-borne vibrations, earth excavation, and subgrade dewatering. These issues have potential to directly and adversely affect abutters and their property. Noise and dust can be nuisance concerns, while vibrations, excavation, and dewatering can result in damage to abutters’ structures. Noise and dust are unlikely to lead to physical damage to abutters’ property, and can be controlled with limited work hours and good housekeeping practices. Vibrations and excavations, however, if not well understood, planned for, and mitigated, can result in serious damage to abutters’ structures. In turn, this damage introduces additional and often significant costs and schedule delays.

Jan 1, 2019

By Karl A. Higgins

In August 2004, the long-awaited National Harbor project in the DC metro area sprang to life with the design of Gaylord National Resort and Convention Center. When the project was in its final stages of construction in 2007, it was noted as largest building development of the east Coast and the 4th largest Building project in the U.S. The final construction costs were above $900M and it served as the catalyst for the overall National Harbor development which added another $1B in construction costs over the next few years. The Gaylord Hotel is supported by approximately 150,000 linear-feet of driven precast concrete piling, one of a handful of major DC area projects in the early 2000s that were supported by this pile type. The project overall was a success, but the fast-paced construction schedule created significant challenges to the designers and contractors. Piling installation was the first major building construction task, and it did not start out well. While the test piles were installed without damage, when production pile driving began in the summer of 2005, pile head and body breakage soon became evident. Typical of most highprofile projects, there are many stakeholders involved and an equal number of opinions on why the piles were breaking. The financial and contractual implications of starting the project off awkwardly were evident to all. The pile driving criteria was scrutinized by the contractor, and the engineer’s had reservations about the size and type of the hammers used for pile driving. Ultimately, it was proven the leading cause of pile breakage was neither the pile driving criteria nor equipment, rather the pile materials themselves. The author of this paper is also the Geotechnical Engineer of Record for Gaylord National and many of the adjacent National Harbor buildings including the recently completed MGM casino. About 100 piles were damaged during Gaylord’s construction some requiring multiple piles for replacements. Over the past decade or so, rumors on the causes of the pile breakage have spread in the market, with some alleging this pile type is not compatible with the geologic setting. I have purposely avoided writing this case-study due to the controversy surrounding the subject, but now some 15 years later it seems appropriate to do so considering DFI’s annual conference location. This will be a fact-based assessment of pile breakage at Gaylord and will also include a comparison to the neighboring buildings where far fewer driven piles were damaged, once a more appropriate concrete mix design was required. The pre-cast supplier is no longer in business.

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

By Jason Herron, Joseph Brown

The common couplings for joining sections of helical piles with an outside diameter of 6.625 inches and 8.625 inches are square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. Each coupling type has advantages and disadvantages in efficiency, capacity, installation, and economics of the installed pile. All these coupling types have been used in the helical pile market in North America for various applications and designs. Many of these applications require on-site testing, but test records are not typically shared with the helical pile industry. Due to the lack of information available for square on square and flange to flange couplings, testing was done to compare the efficiency of installation, load to deflection response, and torque to capacity ratios of external pipe sleeve, square on square, and flange to flange couplings. Field installations and tension tests were performed in non-cohesive (sand type) soil near Caseyville, IL and in cohesive (clay type) soil in Centralia, MO. The data collected during these tests included rotations per foot during installation, installation torque, applied pressure, and deflection. The results of this testing are analyzed and discussed within this paper. The results indicate that the square to square coupling is the most efficient of the designs tested, but this conclusion cannot be fully justified without further testing due to the variability in the data gathered and the small number of piles tested. INTRODUCTION A helical pile is typically assumed to be a medium-displacement pile when its outside diameter is between 4.5 inches and 8 inches and a high-displacement pile when its outside diameter is greater than 8 inches. A helical pile designer has multiple options when selecting a coupling type for medium- to high-displacement helical piles. Each type of coupling has advantages and disadvantages and must be analyzed on the bases of efficiency, capacity, installation, and economics of a project. Typical couplings that are chosen by designers include square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. A helical pile must transfer axial, lateral, bending moment, and torsional loads, and the coupling must be designed to effectively and efficiently transfer each type of load. During the installation of a helical pile, the rate of penetration and the disturbance of soil layers play a critical role in the efficiency and torque to capacity ratio (Kt) of the pile. It is common for a coupling to protrude beyond the outside diameter of the pipe section being used. This is necessary for the function of certain coupling types and can facilitate the connection of couplings. However, it causes increased soil disturbance and reduce the rate of penetration due to soil bearing against the protruding portion of the coupling. A helical pile designer typically will work to minimize the coupling protrusion and create a pile with optimal installation efficiency but may choose a design with lower installation efficiency if it offers sufficient economic advantage.

Jan 1, 2019

By Donald R. Clark

"Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0.Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs.The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths.Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary"

Jan 1, 2017

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017