Search Documents

By R. Rumpold, J. Antrekowitsch

"The continued increase of the automobile production leads to a higher platinum, palladium and rhodium (PGM) demand. Due to the high value of the PGMs the recycle of these metals from automotive catalysts is of special interest. Pyrometallurgical processes, which are only focused on the PGMs, represent the state of the art of automotive catalysts recovery. However, hydrometallurgical recycling processes offer additional recovery of other valuable metals and compounds. The method presented in this paper is based on a combination of hydrochloric acid and hydrogen peroxide to dissolve the valuable metal fraction which can be precipitated afterwards.INTRODUCTIONPlatinum and the corresponding metals from the PGM group, especially palladium and rhodium are well known as catalytic active materials. They support chemical reactions which are inhibited. This effect is used to decrease the amount of harmful compounds like hydrocarbons, carbon monoxide or nitrogen oxides in automotive exhaust gases. The generation of these toxic substances is based on incomplete combustion, which in turn is caused by non-ideal conditions in the combustion chamber. Catalytic converters minimize the harmful compounds by supporting the following Reactions 1 – 3 (Votsmeier et al., 2009).CO + ½ O2 ? CO2 (1)CnHm + (n + ¼ m) O2 ? n CO2 + ½ m H2O (2)2 NO + 2 CO ? N2 + 2 CO2 (3)Platinum and palladium are very effective for the oxidation (Reactions 1 and 2), while rhodium supports the decomposition of nitrogen oxides by carbon monoxide (Votsmeier et al., 2009). The classical three way catalyst was a platinum – rhodium combination with a Pt:Rh ratio of 5:1 (Hagelüken et al., 2005). Today the platinum, palladium and rhodium ratio is highly variable and strongly depends on the engine type as well as on the car producer. Diesel engines are operated with a super stoichiometric air addition in comparison to spark ignition systems. Therefore the exhaust gas composition and off gas temperature is different. Based on the high oxygen amount, diesel engines produce less carbon monoxide and hydrocarbons but more nitrogen oxide in contrast to gasoline engines. This leads to various requirements for the catalytic converters."

Jan 1, 2012

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

By F. Rivard, M. G. Drouet, W. S. Ruff, P. Carabin

"In both the hot rotary-salt-furnace (RSF) treatment of aluminum dross and the cold ball-millsieving (BMS) treatment of zinc dross, enormous amounts of energy and recoverable metal are wasted and large amounts of greenhouse gas are produced. Such wastes and the environment pollution could be avoided by using the DROSRITE PLUS™ technology. Economic and GHG production comparisons between the presently used industrial treatment processes and DROSRITE PLUS™, supported by over one hundred tests conducted in Canada, the US and Europe, are presented. The savings, with DROSRITE PLUS™, would be about $191 and $418 per MT of aluminum and zinc dross, respectively.INTRODUCTIONDross is a material, which forms on the surface of molten non-ferrous metal, such as aluminum or zinc, during melting, metal holding and handling operations when the molten metal is in contact with a reactive atmosphere. Dross normally consists of metal oxides entraining a considerable quantity of molten free (unreacted) metal, and for economic reasons it is desirable to extract the free metal before discarding the residue. In the case of aluminum dross, recovery of the metal is usually carried out by treating the dross in a furnace at a high temperature (Peterson et al., 2002). By contrast, cold zinc dross is crushed in a ball mill followed by sieving to separate the coarse metal portion from the fine oxide residue.The conventional aluminum dross treatment process, using gas or oil-heated rotary salt furnaces (RSF), is thermally inefficient and environmentally unacceptable because of the salt slag and CO2 produced from the combustion of fossil fuels. In the past several years, a number of salt-free processes have been developed and some of these have found limited commercial use (Gripenberg et al., 1994; Lavoie et al., 1990). In all these dross treatment processes, heating of the cold dross in a rotary furnace requires an external energy input that varies between 375 and 2,500 kWh per (metric) tonne of dross. Molten metal separated during processing of the heated dross is tapped, and the remaining solid residue is discharged from the furnace."

Jan 1, 2012

By B. Haneman, J. A. Gorst, W. Slabbert

"The Bayer process involves the digestion of bauxite in caustic liquors at high temperature and pressure. Typically the digestion section of the plant involves the heating of liquors up to the digestion temperature followed by flashing of the digestion product to atmospheric pressure with the flashed steam used to pre-heat the incoming cold slurry. Despite the heat recovery, the digestion process is a high consumer of energy. The application of tube digestion technology in such plants has resulted in significant improvements in refinery energy efficiency with associated benefits of process simplification and refinery flow sheet capital cost reduction. This paper reviews the potential application of this technology to other metals within the non-ferrous industry.THE BAYER PROCESSA typical Bayer flow sheet is shown in Figure 1. The raw feed material bauxite (containing aluminium hydroxide as gibbsite Al(OH)3 and boehmite AlO(OH)) is digested in caustic liquors (caustic soda is the solvent) at high temperature and pressure. This process extracts the alumina and silica and any carbon present on the ore. The slurry is then flashed down to atmospheric condition allowing for heat recovery from the flashed vapour and producing slurry supersaturated in alumina.Following the digestion process the mud is removed via thickening and then pressure filtration to remove fine particulate and produce a clarified liquor with dissolved alumina in solution. The resulting pregnant liquor is then cooled allowing the alumina in solution to precipitate as aluminium trihydrate Al(OH)3. The precipitated hydrate is then filtered and washed and classified into fine and coarse fractions. The fine material is returned to the precipitation process as seed while the coarse fraction is calcined at high temperature to produce alumina. The filtrate from the filtration process (spent liquor) is then heated by the incoming pregnant liquor before being fed to an evaporation process which produced the strong caustic liquor required in the digestion process. Finally, the mud from the thickening process is washed to recover caustic and then fed to tailings ponds. The washer overflow is then mixed with the digester product to increase super-saturation."

Jan 1, 2012

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By T. Boyd, K. McTaggart, J. Qiu

"Hudbay Minerals’ Flin Flon process plant produces a copper concentrate and zinc concentrate from the three ores it processes: 777, Reed and Lalor. Unlike many Cu-Zn ores, the average Zn: Cu ratio in feed is around 2:1, whereas, in many Cu-Zn separation plants the Zn: Cu feed grade is substantially higher than 2:1. The lower Zn: Cu in plant feed is a challenge for limiting Zn recovery to the Cu concentrate. While total recoveries of Cu and Zn at Flin Flon are very good; selectivity is the key challenge and small changes in ore or plant, can result in quite variable Zn recovery to Cu concentrate, and accordingly, Zn recovery to Zn concentrate. Magnetic conditioning has been shown to be selective between the two paramagnetic minerals chalcopyrite and sphalerite. Statistical testing of magnetic conditioning was undertaken at Flin Flon with the objective of increasing Cu recovery to Cu concentrate without increasing the Zn recovery to Cu concentrate - in effect increasing Cu-Zn selectivity. This has been achieved elsewhere with magnetic conditioning with the probable mechanism being an increase in fine chalcopyrite recovery, and a reduction in entrained, ultrafine, non-activated sphalerite to Cu concentrate. The results did indeed show an increase in Cu recovery to Cu concentrate of 0.8% to high confidence, but the decrease in Zn recovery to Cu concentrate was not to high confidence. This is effectively an increase in Cu: Zn selectivity in the Cu circuit – higher Cu recovery with no change in Zn recovery. However, while there was an increase of 1% in Zn recovery to Zn concentrate with magnetic conditioning, the variability in this parameter meant that this increase, though larger in magnitude than the Cu result, was not to high confidence."

Jan 1, 2019

By Marketa D. Evans

The mining industry has a significant opportunity to capitalize on its past learnings in order to build better social relationships. The industry?s relationship with society is both critical and under pressure. Rising levels of public opposition and social conflict are already having material impacts on operations around the world. Industry has an opportunity to shape the future direction of this social engagement, build public trust and proactively respond to a material risk to operations, but first it needs to better understand the nature of the challenges and the urgency of addressing them.

Aug 1, 2013

By T. G. Joseph, A. Sharma

ABSTRACT: Ultra-class haul trucks operating in oil sand face operational and maintenance issues as a result of soft underfoot conditions (Joseph, 2002). With exposure to frequent high g loading events, tire life is reduced due to sidewall belt fexure and frequent ground contact. Therefore, an improved under-standing of the interaction between tires and oil sand is needed. This paper examines the outcomes of a series of static and cyclic loading tests, performed using a scale tire on rigid, sand, and oil sand surfaces. Geometric predictions are made regarding the footprint area and vertical deformation of an ultra-classtire on similar surfaces.

Jan 1, 2011

By K. Huang

"Solvent extraction (SX) is one of the most effective techniques for the multi-metal separation. However, repetitive pre-treatment of feed-in solutions and/or multi-steps two phase equilibrating in conventional SX processes were always unavoidable due to the poor separation selectivity between those metals with similar physicochemical properties. In this paper, our recent efforts, aimed to develop a “Three Liquid Phase Extraction” (TLPE) strategy for one-step separation and selective enrichment of different metals respectively into three coexisted liquid phases, are reviewed. Various feasible “Three Liquid Phase Systems” (TLPS) are evaluated. The TLPE technique provides a potential possibility for multiphase extraction to separate multi-metals.INTRODUCTIONLiquid-liquid Solvent Extraction (SX) is one of the most effective techniques for metal separation and purification. Traditionally, extraction and separation of multiple valuable metals from the leaching solutions of complex ores, industrial wastes and byproducts have to face such difficulties that multiple target metals with similar physicochemical properties co-exist in the solutions, and therefore their mutual separation selectivities are very poor. In conventional organic-water two phase SX processes, repetitive pre-treatment of feed-in solutions including the adjustment of the solution acidity, removal of impurities and/or multi-step liquid-liquid two phase equilibration were always unavoidable (Wang and Chen, 2001). Only one of the target metals is obtained in each extraction step, therefore the whole separation processes for multi-metal separation are typically very long and costly.Liquid-liquid-liquid three phase extraction is a developing technique for separation of complex systems containing multiple target components (Tan, 2003; Shen, 2006; Yu, 2009). The technique is in fact a three-liquid-phase selectively partitioning of different target components through the control of phase-forming behaviors of extraction system to create a unique separation medium with three co-existed liquid phases. The separation selectivity of “Three-Liquid-Phase System” (TLPS) may derive from its three-layered liquid phases from up to down with different hydrophobic or hydrophilic environment, and therefore each phase has its own specific selectivity for dissolving of an individual component. In a well designed “Three-Liquid-Phase System” (TLPS), multiphase extraction and selective separation of different components respectively into three different liquid phases can be achieved by only one-step of extraction. Owing to its distinct advantages, “Three-Liquid-Phase Extraction” (TLPE) technique has found many potential applications in purification of various organic chemicals (Shen, 2007) and biological activities (Chen, 2002; Tan, 2006; Jiang, 2008), treatment of environmental wastewaters (Shen, 2006; Yu, 2009; Yu, 2010; He, 2012), extraction of valuable components in natural products (Liu, 2010) and separation of multi-metals in complex leaching solutions (Jin, 2009)."

Jan 1, 2012

By J. Olaf Sund

"The New Brunswick gypsum and an-hydrite deposits make up part of the Windsor group in the Upper Mississippian. The present deposits were formed by surface hydration of the underlying anhydrite beds. The sub-hydrate, hydrate, and di-hydrate stages of gypsum are formed from the anhydrite by this hydration. The anhydrite was precipitated from sea water in embayments that were separated from the sea by a reef or bay-mouth bar. The anhydrite is the original form of the calcium sulphate precipitate.One gypsum deposit near Plaster Rock in northern New Brunswick was precipitated from sea water directly as gypsum, which is its present form."

Jan 1, 1960

Infrared spectroscopic data collected using HyloggerTM technology is being used to assess the mineral composition of Archean iron ore bedrock and Cenozoic detrital units in Western Australia’s Pilbara region. Analysis of infrared spectra enables quantification of: (1) composite iron mineralogy, (2) composite clay mineralogy, (3) hydrous silicates and (4) carbonate mineral abundances. Stratigraphic and rock mass unit logging of core has identified several detrital and bedrock units recognisable across the Pilbara. However, due to alteration related to mineralisation, weathering and later stage precipitate overprinting, it can often be difficult to assess the detrital-bedrock boundary and the occurrences of specific geotechnical units in the detritals and bedrock, particularly when using non-core drilling techniques and traditional geochemical assays. Infrared spectroscopic data collected concurrently on core from several sites has shown distinct correlation against existing unit subdivisions and associated geochemical parameters. Where infrared spectroscopic data have also been collected on rock chips recovered from reverse circulation infill drilling, these correlations allow robust geological and geotechnical models to be developed based on the typical mineralogical-geochemical signatures. The geotechnical sub-units identified in core can be readily distinguished using the various iron and clay minerals captured by the HyloggerTM technology as opposed to total iron, potassium, and alumina captured by geochemical assays. Further, some of the minerals targeted by infrared spectroscopic analysis (eg gibbsite, white mica, vitreous goethite) and their ubiquitous presence as the products of weathering, assist in recognition of various ancient weathering surfaces and help to define the origin of the material, whether bedrock or detrital. Overall, HyLogging of core and chips allows important mineralogy focussed data to be captured at minimal additional financial outlay. Correlations against geochemical unit identifiers are robust both within deposits and between deposits. Significant improvements in the confidence of geological and geotechnical models are attained.

Jan 1, 2015

By A. Oja, M. Lahtinen, P. Salonen, B. Saxen

Most of the secondary and low grade zinc raw materials cannot be treated successfully by either conventional roasting - leaching - electrowinning (RLE) process or even by atmospheric direct leaching process. The problems arising especially from high impurity content of these raw materials can be effectively solved by implementation of the solvent extraction process. The utilization of solvent extraction process has been demonstrated by Outotec with raw materials like Waelz oxide, crude zinc oxide and zinc containing concentrator tailings. Based on batch and continuous test work it has been shown that SHG quality zinc can be produced even from the lowest grade raw materials. Impurity control in the solvent extraction process has been examined. The solvent extraction process is the key feature of the whole zinc plant for such raw materials. However, design of the entire zinc process including neutralization and bleed treatment is important for optimization of investment and operation costs of the plant. Very careful evaluation of the zinc process with modern simulation tools is essential. The optimized Outotec zinc process ensures a sustainable and profitable process containing minimal effluent and requiring little residue treatment.

Jan 1, 2014

By C. Fortin

ABSTRACT The subject of gold flotation has been reviewed extensively. Most of these reviews focus on the theories of gold flotation and the physical and chemical effects that may impact the efficacy of the gold flotation process. The current status of gold flotation chemistry as it is being applied in industry has not been widely addressed. This paper reviews current gold flotation practice and research advancements and discusses how these applications tie in with the current understanding of gold flotation chemistry. Survey results from worldwide gold flotation operations are analyzed. Potential future areas of gold flotation research are highlighted.

Jan 1, 2013

By A. M. King, J. M. Neilsen

"Roughness at varying scales is an important component of the shear strength of discontinuities. Small scale roughness can be assessed in drillcore and through laboratory testing of drillcore derived samples. Large scale roughness, or waviness, also plays an important part in peak shear strength and a number of methods for its incorporation into defect plane strength models are presented.A number of methods for capturing waviness data from exposed faces are reviewed. A method is presented for deriving waviness from downhole televiewer data, which is shown to be significantly more accurate than structural data derived from core logging. The method is based on work undertaken in the highly anisotropic bedded units of the Hamersley Province, Western Australia where televiewer surveys are routinely undertaken. Values of waviness are derived through a review of variation in dip resolved in the direction of the slope face. This method allows design engineers to incorporate large scale roughness in defect plane shear strengths at the design stage.INTRODUCTIONThere are a number of constitutive models currently being applied by rock mechanics practitioners in calculating defect plane shear strength parameters, such as Patton, Barton – Bandis and Hencher [1, 2, 3]. Most of these shear strength determinations are typically undertaken by determining the base or residual friction angle, and applying corrections for small and large scale surface roughness."

Jan 1, 2015

By Peter N. Blakey, Jean-Paul Paquette, Barton A. Thomson

"FROM THE BEGINNING OF THE PIT, it was known that the surface mining method had a projected life of about ten years, and that the ore extended to depths recoverable only by underground mining. When serious consideration was given to underground mining in 1968, it was realized that tremendous advantages could be gained by starting the underground mine as early as• poss1ble. These included: 1. The availability of underground ore for grade control, which would become more difficult as the pit deepened. 2. The need to develop new systems, equipment and skills to take full advantage of the technological revolution in underground mining. 3. Early knowledge of rock behaviour through trial mining on a small scale prior to finalizing plans for major blocks. In addition, the pit would be available to guarantee the mill supply if problems were encountered. 4. With sufficient time and early mining experience a much better job could be done on all mine planning. Because ample reserves of economic underground ore were virtually assured, the desired underground mining capability became a function of two restraints: first, the time required to excavate and construct the permanent headframe, shaft and ore-handling facilities necessary to handle large volumes of stope ore; second, the time for lateral and stope development on at least one level which would normally follow shaft sinking. The decision made was to move immediately on the permanent hoisting installations and at the same time embark on the planned ramp from surface, which would allow much stope preparation to be completed prior to .bringing the shaft on stream. Both projects were placed on an urgent basis early in 196S' and the following decisions made shortly thereafter."

Jan 1, 1974

By T. Xue, A. Singhal, D. Wrana, I. Mihaylov

"At Vale's Thompson Nickel Refinery, the copper and arsenic in the nickel electrolyte are removed by precipitation using H2S, generating a sulphide precipitate containing about 40% Cu, 8% Ni, 2 to 4% As and 30% S. This residue has been typically stored in impoundment ponds within the plant site. Various options for reprocessing it have been investigated over the years. One of the options involved oxidative pressure acid leach, whereby over 95% Cu, Ni and As were extracted. More recently, an atmospheric alkaline sulphide leaching process for selective removal of 70 to 90% As was developed and mini-plant tested. After alkaline sulphide leaching, the dissolved arsenic is precipitated as stable basic ferric arsenate (BFA) with the addition of ferric sulfate, while the low-arsenic Cu/Ni sulfide is suitable for processing in Vale's operations elsewhere in Canada.INTRODUCTIONVale’s Thompson Nickel Refinery was commissioned in 1961 and currently it has the capacity to produce about 56,700 tonnes per year of electrolytic nickel as cathode slab and rounds products. A sulphate and chloride mixed electrolyte is used in the Thompson refining process and it typically contains 75 to 85 g/L Ni, 50 to 60 g/L Cl, 90 to 120 g/L SO4 2-, 25 to 30 g/L Na and 8 to 9 g/L boric acid. The main impurities in the Thompson anolyte are copper, cobalt, arsenic, iron and lead.The simplified Thompson electrolyte purification flowsheet is shown in Figure 1 (Oliver & Wrana, 2009, Goble & Chapman, 1986); it consists of precipitation of copper, arsenic and lead with H2S, followed by nickel replenishment with ground matte and acid and removal of cobalt and iron with Cl2 and NiCO3."

Jan 1, 2012

"Yara Siilinjärvi in Finland is the Western Europe's only apatite mine. Annually it produces one million tons of apatite concentrate, which creates 10 million tons of tailings. At the beginning of 2017, Yara replaced their conventional TSF with a new tailings treatment plant, which increased the solids content of the slurry from 45–48% to 66–68%, making it possible to deposit as a paste. This extended the life-span of the current TSF from 2020 to 2035. This paper presents the storyline of the Yara paste plant project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After successful pilot trials, the final process design was implemented. Process automation played a key role in the project. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances. Since commissioning the paste plant has been running consistently with an underflow solids content of 66-68%, with average beach slope angles of 3.5 degrees in the tailings disposal area. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the plan. During first year of operation the plant’s availability has been very good, over 97%, and currently, the plant is operated remotely from the main concentrator plant.INTRODUCTION The Yara Siilinjärvi Plant is owned by Yara International, a Norwegian fertiliser company. Yara Siilinjärvi is Western Europe's only apatite mine, and it primarily produces apatite concentrate for its Siilinjärvi phosphoric acid plant. A portion of the concentrate is also dried and shipped to other Yara fertiliser plants. The site annually produces one million tons of apatite concentrate, which creates approximately 10 million tons of tailings. Extending the lifespan of the 1150-hectare tailings storage facility has been studied in Siilinjärvi for a long time. The aim has been to use the same tailings area footprint, without any new land purchases or major dam increases. An important part of the process has been to study the possibilities for using new technologies, especially thickened tailings technology (Ruhanen, 2014)."

Jan 1, 2019

By Andrew J. Troop

"VAUGHAN THOMPSON designed the Thompson retrievable diamond drill wedge and reaming assembly in 1948. Since 1950, the Hudson Bay Exploration and Development Company, Limited has used the method extensively. The wedge, setting tool, and reamer have been modified slightly since they were first introduced. In 1951, Mr. Thompson designed the Thompson arc cutter. The purpose of this tool is to decrease effectively the diameter of the arc cut, using standard drilling tools. This directional drilling device is usually employed when a branch hole is desired. The Thompson arc cutter has been used with success at Birch Lake, Saskatchewan, at the property of Cuprus Mines, Limited, Manitoba, and at Thompson Lake, Manitoba.UsesThe Thompson retrievable wedge provides a simple method for:(1) Re-drilling lost core sections(2) Re-sampling sections of old holes(3) By-passing lost tools Correcting the direction of a hole(4) Drilling a branch hole to obtain intersections at a higher elevation than the original holePrevious to the spring of 1951, the wedge was used only for the first four of these purposes. Recently it has been employed extensively for drilling branch holes."

Jan 1, 1953

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By A. O. Dufresne

Introductory At the Annual Meeting of the Institute, held two years ago, I had the privilege of presenting a paper on Recent Mineral Discoveries in Western Quebec. In it were pointed out the areas favourable for prospecting in that section of Quebec adjoining the mining camps of northern Ontario; the discoveries that ?had been made were recorded; and some of the developments up to that date were reviewed. Since then, two full years have elapsed, during which a considerable amount of serious work has been performed with such results that western Quebec has today six properties about ready to mine commercial ores of gold, copper, and zinc. These results have been brought about after large sums of money had been invested to bring the district to a producing stage. A smelter has been built, and is already producing copper; two railways have extended their lines into Rouyn; and the Provincial Government has shown faith in the future of the district and has spent large sums of money in the building of highways and for other public works. The purpose of the present paper is to review the developments of the last two years, and the work that has been performed in various spheres of activity in that section on western Quebec covering the county of Abitibi and the northern part of the county of Temiscamingue.

Jan 1, 1928