Search Documents

The Porgera mine and treatment plant are located in the Enga Province of Papua New Guinea. Gold in the Porgera deposit is found free and in association with the primary sulphide mineral pyrite. The refractory nature of the gold in the pyrite r

Jan 1, 1997

The New Broken Hill Consolidated Airshaft is the first major undertaking in the development of New Broken Hill Consolidated Ltd's. property, which adjoins that of The Zinc Corporation Ltd. on the latter's southern boundary.The Zinc Corporation ore-body has a southerly pitch. The Zinc Corporation's New Main Shaft is 1000 ft. north of the common boundary, and the general plan of development of the New Broken Hill Consolidated property is by driving south from this shaft on the lower levels. No downcast airway from the surface was available south of the Zinc Corporation's New Main Shaft; this shaft acts as the main downcast to the bottom of the Zinc Corporation mine, the general air flow then being northward and upward to the upcast shaft at the extreme north end of the Zinc Corporation property.Rock temperature is 920 F. at 2000 ft., increasing by 10 Fahr. each 72 ft., the rock temperature at 3000 ft. being estimated at 1060 Fahr. With the general air flow northward from the Zinc Corporation's New Main Shaft, adequate ventilation under these temperature conditions would not be practicable for any great distance south of this shaft without another main airway from the surface. Accordingly the New Broken Hill Consolidated Airshaft is being sunk at a point 1000 ft. south of the common boundary, i.e., 2000 ft. south of the Zinc Corporation's New Main Shaft, to ventilate future New Broken Hill Consolidated workings and that part of the Zinc Corporation mine between the boundary and the New Main Shaft.

Jan 1, 1940

At the beginning of the seventies pre- drainage of methane was introduced in West German coal mining in order to reduce the gas emission from the worked seam. After three pilot tests on the "Rheinland" Colliery (86 boreholes in seam "Prasident"), "Bergmannsgluck/ Westerholt" Colliery (23 boreholes in seam "Gustav") and "General Blumenthal" Colliery (27 boreholes in seam "Hugo" and 170 boreholes in seam "Karl") systematic large scale tests with extended investigations were carried out un the "Rheinland" Colliery (127 boreholes in the seams "Anna", "Blucher", Prasident"). During this time an analogous test was carried out on the "Consolidation" Colliery (21 bore- holes in seam "B"). In these studies and tests the technical feasibility, efficiency and economy could be proved, so that pre-drainage of methane starts spreading. On the "Rheinland" Colliery pre-drainage has become common practice in gassy seams. Mainly two points impede a faster spreading of method: 1. in many cases the necessary requirement, that one or both of the gate roads should ire driven 6 to 12 months before the face is worked, is missing. This is mainly due to the difficulty of retreat mining in passe seams.

Jan 1, 1982

By J F. Colinet, G, J A. Zimmer, R J. Timko

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/non-metal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 per cent throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurisation systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a workerÆs clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2005

By Just GD, Gillies ADS

There is an increasing need for reliable and comparable coal resource data and it is necessary to standardize the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can consider- ably improve classification quality. A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed. Application of the method in classifying resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results which closely reflect the error associated with an estimate of resource quantities based on current sampling densi- ties. It requires a careful geostatistical analysis with emphasis on geological awareness. Resource category restrictions must be arbi- trarily assigned and remain constant for all deposits being compared. Engineering judgement is needed and interpretation may be required with isolated and peripheral blocks.

Jan 1, 1987

By Hare S. M, Lumsdaine I, O&apos

Converter slag assaying 3.7 per cent Cu is produced by Mount Isa copper smelter at a rate of up to 180 000 tonnes per annum.Priority is given to the processing of ore, however concentrator capacity periodically exceeds that of the mine and the opportunity is taken to treat converter slag. It is processed in batch campaigns, typically through the Copper Concentrator, but the Hilton Concentrator has also been used. Slag and ore are kept as separate as possible, since each has an adverse effect on the flotation performance of the other.

Jan 1, 1993

Excavator output rates given in Makers' catalogues are sometimes based on favourable operating conditions. Mine operators and planners are more interested in the Effective Hourly Output in normal operation (Qe) a plant system can give hour by hour and year after year in a particular application. The number of hours mining plant will be available for normal operation will be less than the annual total of 8760 h. The number of the available hours which can be utilised at Qe will depend largely on the number and types of units in the plant system, the manners in which they are applied and the nature of the deposit in which they work. The emphasis herein is on continuous systems for deep stripping with BWE's as the primary excavator. Examples and suggestions are given for the annual hours at Qe for some BWE systems.

Jan 1, 1981

By Thompson M

The humble gabion basket is to mine development what the light bulb and safety pin are to eir-ryday life. Gabions provide a flexible, easy to assemble and cost efficient solution for "101" mine and civil engineering development applications.In some instances gabion baskets are still efficiently in use after many years of faithful, maintenance-free service. In other situations, the baskets have been demolished or made redundant within days, either having served their temporary usefulness or negligently destroyed by the operator of heavy equipment. Either way, the gabion basket must surely rate among the top 10 cost efficient engineering construction materials.

Jan 1, 1994

By B Lavin, R Sanford

This paper examines the application of Lean Manufacturing in a mining environment, based on experience within the Rio Tinto entities: Rio Tinto Aluminium, Northparkes Mines and Hunter Valley Operations. The three applications have tested the flexibility of the Lean methodology. Within Rio Tinto, Rio Tinto Aluminium was the first group to introduce Lean. The rollout began in late 2004. It was introduced firstly at Boyne Smelters, Gladstone, as a model site with the initial application in the Carbon Bake Furnace area. It was later extended to other sites including the Weipa Bauxite Mine. LeanÆs successful application within Rio Tinto Aluminium was in part responsible for its recent adoption by other Australian-based Rio Tinto business units including Northparkes Mines, a copper mining operation in Central New South Wales, and Hunter Valley Operations, a group of four coal mines in the Hunter Valley region of New South Wales. Lean is also being adopted by Rio Tinto Iron Ore. Rio Tinto Aluminium introduced Lean Manufacturing to complement an existing Six Sigma business improvement program and to achieve continuous improvement activities at a workplace level. Lean provides a similar level of rigour and discipline to Six Sigma but its application is everyday and for everyone, everywhere in the workplace. It is a valuable management tool. In a short time, Lean has achieved good and sometimes spectacular results improving productivity and efficiency at all sites, including our mining site. Within Rio Tinto Aluminium, it has also had beneficial impacts on our ability to develop and retain employees.

Jan 1, 2006

By G Hobart

Laboratory flotation tests were conducted to investigate the role of pH, zinc sulfate and potassium metabisulfite in the flotation of galena and marmatite in the Broken Hill orebody. Marmatite was depressed under alkaline conditions alone, however the addition of the two depressants, either individually or combined, resulted in the greatest selectivity. The use of zinc sulfate under alkaline conditions resulted in good selectivity whilst maintaining a high lead recovery. The addition of potassium metabisulfite under alkaline conditions reduced zinc recovery, but high additions reduced lead recovery. The addition of both depressants at alkaline pH produced the best result, with a lead concentrate of 72.6 per cent at 98 per cent recovery with less than four per cent zinc recovery.

Jan 1, 2005

By A Hollonds, R Young

High commodity prices have produced a boom in project expansions and growth projects. Unfortunately, some of the early results have been poor, with some projects suffering considerable cost growth, project delays and start-up problems. The cost growth experienced in some projects is well beyond just escalation, but suggests weaknesses in the development of feasibility studies. Independent project analysis (IPA) has developed a large database containing information on project outcomes in the minerals and metals sector, and has identified, through its front-end loading (FEL) index and team development index (TDI), some key leading indicators of project success and project problems. This paper highlights key areas of weakness in feasibility studies that have driven poor project results, and the best practices that have driven improved project results.

Jan 1, 2009

Competition in the mining industry is the main driving force for both equipment manufacturers and end users to develop and apply the most cost efficient solution to a mining problem. Therefore the challenge to find new solutions is usually met by several suppliers under various factors of influence affecting specifications. Time and timing are particularly important, but all new developments ultimately have to successfully perform on site.Consideration of all aspects of planning, manufacturing, user liaison and ultimate satisfactory commissioning hinges on the necessities of assessing of all the expectations in the mining application and the requirements of the concept and layout team. To apply the maximum available technical competence with solid thorough workmanship is the best possible foundation for success of underground machinery development.

Jan 1, 1991

Mine scheduling is a process which represents what happens in a mine over time. An optimised plan involves selecting the best workable plan which meets a stated objective. This paper discusses some of the theory and philosophy behind mine scheduling and explains how scheduling is a step in the total iterative mine planning process. Several schedules may be necessary before arriving at a mine plan which can be considered optimal. A description of broadbrush and detailed scheduling is given and the features of computer assisted scheduling are also described. The use of mathematical modelling techniques in conjunction with scheduling to optimise the mine plan is explained. The need to incorporate these techniques to optimise the whole mining system rather than only a part, is emphasised.

Jan 1, 1991

The issues which are the subject of this paper cover an extremely broad field. In themselves the components of the topic could be the theme, in considerably greater detail, of a two day seminar. Indeed a full course in an academic year would probably not do justice to the topic. I have therefore experienced considerable difficulty in condensing such a broad subject range down to a 30 minutes address and in doing so have tried to, hopefully, provide a little bit of everything for the wide range of professional interests and different levels of commercial, professional and legal expertise represented at this conference. Perhaps my address could best be described as a "bird's eye" view rather than a "worm's eye" view of the subject.

Jan 1, 1990

The determinants of human behaviour are numerous and complex. Many scientific disci- plines focus on various processes which play some part in shaping the actions of individ- uals and groups. Behavioural science attempts to synthesise data produced by these investigations in an attempt to formulate principles by which people's thoughts, feelings and actions may be described, diagnosed, predicted and changed. While no comprehensive account of people and their reactions can be attempted in a brief paper a review of six principles does provide a framework within which managers can establish reliable knowledge applicable to all their subordinates and to themselves. This information may be used to arrange organizational environments and management practices which enable people to discover, release and increase their best intellectual, emotional and motivational capacities.

Jan 1, 1982

Future metal prices play a direct role in both the economic evaluation and short to medium planning of a mine scheduling sequence. It is difficult to predict with accuracy the future price of volatile metal commodities, however, it is possible to fix some future metal price, outside of long term contracts by the selling of futures contracts through a commodities exchange. The futures contract represents a fixed amount of a speci- fied quality of a commodity for future delivery at a predetermined price. Several different types of hedginc are possible, one in particular which is best suited for mining companies. There are relative advantages and disadvantages when trading in futures contracts and particular reference is made to gold contracts on the Sydney Futures Exchange.

Jan 1, 1980

An extensive study was carried out to evaluate the performance of Outokumpu OK50, OK38 and Maxwell MX14 cells at ComincoÆs Red Dog flotation concentrator in Alaska. Tests were conducted by varying operating conditions of the cells installed in different circuits in the plant. The hydrodynamic and gas dispersion properties were measured and the metallurgical performance of the cells was evaluated for each condition used in the tests. This paper highlights the importance of superficial gas velocity, bubble surface area flux, gas hold-up, power consumption, residence time distribution and froth flow behaviour in optimising cell performance. The findings of these tests provide valuable insights into selection of the best cell operating conditions to optimise circuit performance.

Jan 1, 2000

Industry can achieve best results via thorough planning, consultatiion with agencies and local communities and a 'hands on' approach to' environmental problem solvingThe Department of Energy and Minerals, through its Minerals Group, has regulatory responsibility for the mining and extractive industries in Victoria. The role of the group is to facilitate the environmentally responsible development of these industries for the benefit of Victorians. It has a wide range of contacts with other government agencies, local government and community groups.The paper is in three parts; firstly, an overview of the nature and contribution of the mining and extractive industries in Victoria; secondly, the industries' regulatory framework; and thirdly, the environmental issues facing the industries and the management of these issues.

Jan 1, 1992

By Carlie JC

Many low sulphidation epizonal gold and zinc-lead vein deposits within magmatic arcs are situated on basement highs, and post-date both the main volcanic episode and porphyry copper (gold) mineralization. These features are best explained by emplacement of a flat batholith a few kilometres beneath each mineral district, as recently demonstrated by geophysical data in the Baia Mare district of Romania. The batholith provides heat for the hydrothermal system, and results in extensional faulting both through up-doming of the overlying rocks, and in some arcs through incipient collapse of the thermally weakened crust under regional extensional stress. More water-rich magmas emplaced at greater depths could explain some deep epizonal and mesothermal gold deposits situated outside magmatic arcs.

Jan 1, 1995

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992