Search Documents

By K. C. Ko, D. A. Pifer

The theory of probability with respect to the failure of structures is discussed. It is shown that the probability of safety, probability of failure, and factor of safety are directly related to each other and that as standard deviation approaches zero, the probability curves approach a unit step function which can be interpreted as the conventional factor of safety. The factor of safety is numerically the ratio of the load to the strength of the material at a particular point or plane in an engineering structure. Mathematically, it can be illustrated as a unit step function undefined at the point where the factor of safety is one (Fig. 1). The uncertainty of variation of soil and rock strengths require factors of safety much higher than those used in other engineering structures. The factors of safety used are generally determined from past experiences with similar structures. However, the factors thus determined do not have any theoretical meaning or do not indicate any relationship to actual safety.' It seems, therefore, logical to develop a system with a sound theoretical basis to obtain a more suitable factor of safety for structures. An application of elementary theory of probability indicates that it is possible to relate this number to theoretical and practical engineering facts.

Jan 1, 1971

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By C. A. Stiles, J. W. Nyhus

Erie Mining Co. is a 10.3-million-tpy pellet producer on the east end of the Mesabi Range 60 miles north of Duluth. Its complex includes facilities for mining, crushing, grinding and beneficiation in addition to a pellet plant and power plant. A 74-mile railroad links the mine and plant to Taconite Harbor on the shore of Lake Superior. The concentrate recovery ratio at Erie is about 1: 3, and this, along with stripping activity, makes it necessary for the company to mine nearly a million tons of material a week. At the outset, all crude ore mined at Erie was hauled entirely by rail, but with expansion into additional mining areas, the company made a gradual transition towards truck-to-rail haulage. Today, in Erie's 11th year of operation, over 50% of all crude taconite mined is transported by truck to loading pockets where it is transferred to rail cars. Future years will see more taconite moved in this manner. Thus, the company has an increasing interest in tire performance.

Jan 6, 1969

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

L. D. GODSHALL, Everett, Washington: This very interesting paper cannot fail to command the attention of every one who has ever had experience in the amalgamation of gold-ores. I wish to call attention to three very important facts brought out very prominently by the paper, namely: 1. The extent of accumulation of amalgam on copper plates in the form of scale, not removable in the ordinary manner; 2. The change in the relative quantity of the two metals in the amalgam as we. recede from the battery-discharge; 3. The difference in fineness of the bullion obtained from the above-mentioned scale as compared with the bullion from the daily clean-ups. From Mr. Bayliss's figures we find that during the life of the plate in question 14,942 tons of ore were crushed, yielding amalgam of the value of $5.03 per ton, or a total value of $75,158.26. The amalgam accumulating on the plate during this time as scale, we find to have had a value of $8340.54, or $0.558 per ton of ore treated, representing 11.09 per cent. of the total amount of amalgam saved in the ordinary clean-up; or, taking the amalgam saved by daily clean-up plus the amalgam-scale as representing the total saved on this plate, or 100 per cent., we find that the daily clean-up saved 90.01 per cent., while the scale represented 9.99 per cent. The above figures do not include some additional amalgam still adhering to the plate after scale had been removed. We are told that this was not an exceptional case at the Drum Lummon, but that other plates have even yielded a third more than the one in question. The interesting query now comes up, whether this experience at the Drum Lummon is exceptional or universal at all mills; and another question arises, as to how long such an accumulation might continue,

Jan 1, 1897

By Eugene McAuliffe

THE last obtainable figures of the value of the coal mining investment are those contained in the U. S. Census Reports, from data gathered in 1919. The values shown therein and set forth below cover lands and equipment and do not include distribution and marketing facilities. The working capital necessary to meet pay rolls to purchase material and supplies and workmen's compensation insurance are likewise excluded.

Jan 1, 1926

By Zdzislaw Specht

THIS paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, rang-ing sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration.

Jan 1, 1940

Rutile – Zircon Mining on East Coast Surfing Beaches – Rutile-Zirconium Producing Companies in Australia

Jan 10, 1964

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By K. E. Manchester, C. B. Sibley

The feasibility of doping silicon to produce device structres by directly implanting impurity atoms has been demonstrated. Both phosphors and boron ions have been successfully implanted in silicon to produce electrical junctions. Junctions as deep as 1.2 p have been produced by phosphorus ions having energies the order of 80 kev. An electromagnetic separator has been used to controllably produce uniform, large-area implantations for evaluation experimentation. Correlations between junclion depths and ion energies huve been obtained. Orientation effects have been observed and it has been found that the (110) direction is the easy direction for implanting. Monitoring of thermal treatments oj implanted substrates by sheet-resistance measurement indicates a very mild thermal anneal removes most of the damage done during the implantation. These indications are further substantiated by reverse-current measurements of j,inctions Produced by implantation. Electrical characteristics of implanted junctions are compared with those of diffused junctions. We have been interi n the interaction of energetic ions in the III-V groups, in particular boron and phosphorus, with single-crystal silicon to produce type conversion for possible device use. A number of investigators, a few of whom are avies, Kornelson,3 and so forth, have reported on penetration of energetic ions into both amorphous and crystalline solids. While most work has been done with ions of the rare gas and alkali metal groups, some work has been reported by ing, erber,' and others6 in which ions of the 111-V groups have been implanted in single-crystal silicon. A large amount of this work has been done with ion energies in the 100-kev to 1.5-Mev range. An excellent review article has been written by caldin. We have concentrated on ion energies which are in the 10 to 80 kev range, with which over 1500 implanted junctions such as the one shown in Fig. 1 have been produced in silicon substrates with both phosphorus and boron ions. Fig. 1 is a 3-deg angle lap in which the n type area produced by 66 kev P is delineated and the junction is 9500A below the surface. EXPERIMENTAL Implantations reported in this paper were made with the ion source adjusted to produce ion currents in the range of 1 to 2 pa with accelerating voltages varied from 10 to 40 kv. When using doubly charged ions this produced 10 to 80 kev ions. This allowed substrate temperatures to remain below 100°C. Sam- ple movement resulted in beam impingement angle variation of 7 deg from the normal to the substrate surface. Substrate resistivities have been varied through the range of 0.001 to 500 ohm-cm and specimens oriented in three directions, (110), (Ill), and (loo), within 12 deg. RESULTS For the purpose of this paper, discussion of results will be limited to phosphorus implantations with mention of results for boron-implanted silicon. Similar results have been obtained for boron and will be reported at a later date. In Figs. 2, 3, and 4 depth penetration is shown

Jan 1, 1967

By L. D. Jaffe

IN previous metallographic work on titanium and its alloys, difficulty has been encountered in distinguishing spheroidal particles of titanium hydride, dispersed in a-titanium, from other phases that may be present, such as p-titanium. This problem is common in examination of commercial unalloyed titanium.' In the course of an investigation of the Ti-H phase diagram, it was noted that titanium hydride, dispersed in a matrix of a-titanium, showed strong optical anisotropy when examined under polarized light. With sensitive tint illumination, particles of the hydride, when the stage is rotated, changed from bright yellow to bright blue in color. Since P-titanium is cubic, it showed no color change on rotation, remaining dark gray or blue-gray. Although a-titanium is hexagonal, it showed only a minor color change, going from pale pinkish-blue to pale purplish-blue. These colors could be modified somewhat by adjustment of the illumination. They were observed in specimens mechanically polished, both without etching and after etching with hydrofluoric acid-nitric acid mixtures in either water or glycerine. The strong color change of the hydride seems to offer a simple method for its metallographic identification. Optical anisotropy of titanium hydride is inconsistent with its accepted face-centered-cubic structure.' Samples of iodide titanium containing 6 to 40 atomic pct deuterium were prepared for diffraction studies. After deuterating and slow cooling' the samples were held 21 % hr at 400 °C, water quenched, held 61 hr at 100°C and quenched, then held 64% hr at 255 C and quenched. Debye ex-posures with MoKa X-rays and 1.111A neutrons were made at room temperature of samples as-deuterated and after the 100" and 255°C treatments. Table I shows the lines observed, in addition to those attributable to a-titanium. These data show that the hydride phase was not cubic, but probably tetragonal. The titanium atoms appeared to form a body-centered-tetragonal lattice complex, two titanium atoms per cell, with approximate dimensions: a = 3.12A, c = 4.18A, and c/a =1.34A. This is equivalent to a face-centered-tetragonal complex, four titanium atoms per cell, with approximate dimensions: a = 4.42A, c = 4.18A, and c/a - 0.946A. The presence of the 2.98 and 1.81A neutron lines indicates that the true Bravais lattice is not identical with this lattice complex, but may be primitive tetragonal with dimensions some multiple of those of the complex. The relative intensities of the hydride and a-titanium X-ray lines as functions of overall composition indicated that the hydride, presumably in equilibrium with the a at 100" to 255"C, contained more than 62 atomic pct H. Acknowledgments The experimental work covered in this report was done at Brookhaven National Laboratory, through the courtesy of D. Gurinsky. The cooperation of J. Sadofsky, 0. Kammerer, A. McReynolds, and A. Cendrowski is gratefully acknowledged.

Jan 1, 1957

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By Axel Sahlin

Jan 1, 1898

By W. D. France, H. l. Burghoff

FABRICATORS of copper and copper alloys have contended with the problems of reconversion during the past year in endeavoring to return to the full-scale production that is demanded of them. The problems have not been easy, for the industry, like so many others, has had to deal with strikes of long duration, and material shortages, particularly in the raw materials, copper, zinc, lead, and tin. Despite all these obstacles, it was possible to gear production to new peacetime records during the latter part of the year. This was made possible not only by the use of multiple shifts of personnel, but also by the improved production equipment, the development of which had been stimulated by wartime necessity. The work of installing new and better equipment is still continuing, and virtually every company is engaged in improving or planning to improve its processes.

Jan 1, 1947

Jan 1, 1969

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944