Search Documents

By Michael L. Boucher

Copper and nickel sulfides occurring in the Duluth Complex of northern Minnesota were examined at the Bureau of Mines, A microscopic study was undertaken to determine the mineralogy and paragenesis of the ore minerals. Eighty-two samples were taken from one deep diamond drill core located near Babbitt, Minn. Modal analyses are presented for the Duluth Complex rocks and for the are minerals in the major mineralized zone. The major sulfide minerals are chalcopyrite, cubanite, pyrrhotite, troilite, and pentlandite. Results of this investigation suggest that the mineralization is related to the structural features of the enclosing rocks: pores, open fractures, and cavities. The pyrrhotite-troilite-pentlandite assemblage is believed to have formed from an immiscible sulfide melt, probably associated with the troctolitic rocks. Most of it settled to the very porous base of the Duluth Complex, and to the other porous zones near xenoliths; small portions were trapped higher in the section. A later introduction of a copper-rich sulfide melt replaced some of the pyrrhotite-troilite and oxides, and filled in the remaining open spaces and fractures in the Duluth Complex and those of the adjacent footwall rock.

Jan 1, 1975

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION Tunnels are commonly constructed in the very weak St. Peter sandstone in the Twin Cities area of Minnesota. Historically, core recovery in this weak sandstone was very small in the critical weaker strata resulting in little preconstruction information on the ground conditions. Improved core recovery techniques have been utilized for recent projects, allowing rock quality rating methods to be developed for the recovered core. Down-the-hole tests, and the use of combination ratings between different types of core data provide for more detailed characterization of ground conditions. THE ST. PETER SANDSTONE The 45 m thick St. Peter is an unusually pure quartz sandstone. It underlies all the Twin Cities area, except where it has been eroded by the present day Mississippi River or by pre-glacial rivers. It forms conspicuous steep bluffs along the Mississippi River where the upper Platteville limestone formation protects it from erosion. Where the Platteville formation is missing, the sandstone slopes are often more gentle. Natural case hardening of the exposed sandstone bluffs often forms a resistant crust and reduces sloughing. This case-hardened surface is not representative of the sandstone back from the bluff.

Jan 1, 1987

By Sigurd L. Lamhauge, Karl Gunnar Holter, Svein E. Kristiansen

An innovative sprayable waterproofing membrane in combination with the traditional Nordic method of waterproofing with polyethylene foam sheets was used for the waterproofing of the tunnel. The sprayable membrane was integrated in the final sprayed concrete lining in a sandwich structure, hence constituting a composite water-proof lining based on sprayed concrete. The spray able membrane was applied in areas with small to moderate water ingresses, making up approximately 50% of the total area requiring waterproofing in the tunnel. State-of-the-art application technology with a computerized spraying robot was used. A consistent application of the required thickness at a high speed was thereby achieved.

Jan 1, 2007

By Healy T. W, Dixon D. R

The present study 'of pure ZnS and NiS and ZnS (marmatite) by detailed electrokinetic methods has shown that by careful control of experimental parameters much new' information on sulphide-water interfaces can be obtained. Time-dependent processes of alteration of sulphide surfaces are foHowed by electrokinetic methods and indicate that the isoelectric point of the surface depends on elemental sulphur coverage, oxidation product coverage, and the conditions which promote or minimize such reaotions in the presence and absence of activator.

Jan 1, 1977

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By G. Goodall, R. Jabbar, S. Muinonen, A. Cummings

"Glencore’s Sudbury Integrated Nickel Operations in Falconbridge, Ontario, has been in operation since 1930. Many new technologies and practices, now common in the industry, have been implemented at the site and contribute significantly to the industry’s understanding. Since the last update on the Smelter operation published at the NiCo 2005 conference, the Converter Aisle has undergone significant changes in the operation of vessels. The Aisle continues to consist of 4 Peirce-Smith converters, but the Slag-Make Converter, and the Slag Cleaning Vessel have been re-tooled or re-built as Hybrid Vessels (HV), each generating matte for the two Finishing Converters and clean slag for disposal. The complicated scheduling and the overall benefits to the Smelter are reviewed here as part of the on-going tradition of industry support.INTRODUCTION The Glencore Nickel Sudbury Smelter operates a Roast Reduction Smelting (RRS) flow sheet with a specialized Converter Aisle operation that maximizes metal recovery to Bessemer matte. The main process equipment consists of a pair of Fluid Bed Roasters, a submerged-arc Electric Furnace and four Peirce-Smith converting type vessels (Figure 1). In the RRS flow sheet, concentrate is roasted with air to remove sulphur as SO2. Calcine from the Roasters is mixed with petroleum coke upon addition to the six-in-line rectangular Electric Furnace. The coke back reduces the metallic oxides, producing a matte and a discard slag.Gases from the Roasters are sent to a single pass absorption Acid Plant where the SO2 is converted to acid. Under the previous operating targets, approximately 70–75% of the sulphur in the incoming concentrate was fixed as acid with the balance going to the Electric Furnace in calcine for Bessemer matte production. Off-gases from the Electric Furnace and Converters are combined in a balloon flue, treated for particulates in electrostatic precipitators and discharged to the Smelter stack without any SO2 fixation."

Jan 1, 2017

Urban development to the south of Sydney is approaching areas of current and proposed coal mining. Already some structures and residential areas are affected by mining subsidence.Subsidence resulting from either conventional pillar extraction methods or longwall mining has been monitored for 15 years to enable the characteristics of the surface deformation to be determined.The vertical and horizontal displacements of survey stations on the surface are monitored and the results arc used to calculate subsidence, changes in slope of the surface, curvatures along the subsidence profile, and the ensile and compressive strains. These features are in turn related to the underground extraction to give a description of surface subsidence and the development of subsidence with time.Subsidence investigations have been carried out over all or part of the workings of six collieries in the Southern Coalfield.Two case histories illustrate the procedure in the investigation of subsidence phenomena. The first example is the study of the subsidence over a series of longwall panels in one seam and the second is a study of subsidence over pillar extraction in two seams one above the other. From the results of the investigations the effects of panel widths on subsidence are determined.This and other information assists mine planning in areas where surface movement and deformation are important considerations.

Jan 1, 1980

By Q. G. Reynolds

Keywords: Pyrometallurgy, furnace, DC, reverse polarity, dual-electrode The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode, and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions ? this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magneto-hydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

ONE of the phases of mining wide ore-bodies, such as are found in Broken Hill, is the laying-out and design of the sill floor gangway timber, When, in the above operation, a detail has to be repeated frequently, it is desirable in the interests of efficiency that that detail should be standardized as far as possible. Before arriving at a standard design e.g., a crosscut layout-it would seem necessary to compare its strength with some other unit of timber and see that the general design is at least as strong as the unit that has been taken for comparative purposes, In these notes no attempt is made to calculate the stresses to which timber underground is subjected, but merely to draw a comparison between the relative strengths of the various cross sections of timber in common use underground.It has been assumed for the purposes of comparison that the milling exerts pressure in a vertical plane only, and is uniformly distributed over any area. A beam supported at both ends, and with a uniformly distributed load, has the maximum bending moment at a point midway between the points of support, and equals- WL2 8 where W = load per unit length. L = distance between points of support.The bending moment also equals M-, where y M = modulus of rupture of the material in question. I = moment of inertia of the section of the beam about a given axis.Y = distance of extreme fibre from that axis. WL2. I The formula -8- = MY- only holds good until the elastic limit...

Jan 1, 1923

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By M. P. Valoski

Mine fires and/or explosions continue to occur. While these are unusual events, they comprise emergency situations. Whenever one of these events occurs, the Mine Safety and Health Administration (MSHA) responds with specially trained teams, mine fire experts, sophisticated scientific instrumentation, and trained instrument operators. In order to analyze mine air samples on-site, because time is of the essence, MSHA has a Mobile Gas Laboratory. The laboratory, which is stored near Pittsburgh, is totally self-contained. Sending air samples to a laboratory would take too long. Mine fire experts need the results of the latest analyses as soon as they are finished. The mobile laboratory is housed in the box of a diesel truck. Benches line both sides of the laboratory. Gas chromatographs are mounted on the benches. There is sufficient bench space for multiple bench top gas chromatographs. These instruments and their controllers are shock and vibration isolated to protect them during transit. The mobile laboratory can operate using on board diesel generators or line power. An uninterrupted power supply (UPS) supplies power to the instruments while switching from generator to line power or visa versa. Therefore, analysis of samples can proceed without interruption if a power failure would occur. In the rear of the mobile laboratory are racks that hold compressed gas cylinders. These cylinders contain carrier gas and compressed air. An air compressor is housed under the laboratory to operate the gas chromatograph actuators. Within several hours after arriving at a mine the instruments have stabilized and have been calibrated. The mobile laboratory is ready to begin analyzing air samples. The mobile laboratory has proved itself at many mine fires and explosions since its purchase.

Jan 1, 2009

By Tony Robles

"A new process is disclosed for the recovery of gold and/or silver values from activated carbon wherein they are adsorbed as cyanide complexes. A unique chemistry allows the new process to use mill process water containing an inexpensive, non-hazardous compound as the eluant. The new process has an elution period of 5 hours at 98°C. The gold in the eluant can be recovered by electrowinning or zinc precipitation. The new elution process is simple, reliable, and provides an eluted carbon that may not require thermal regeneration before reuse. Retrofitting the new process to existing processes such as Zadra, Anglo, and others will not require significant capital expenditures.IntroductionThe efficient and reliable elution process for gold/silver from activated carbon is a very important process in the gold mining industry. The most common techniques for elution of gold cyanide from activated carbon are the Zadra and Anglo procedures.Specialized elution techniques like the Micron and Acetonitrile processes have not been commercialized to significant extent probably due to relatively complex unit operations and expensive reagents.Important functions of the gold recovery circuit are:Efficiently recover gold/silver from the loaded carbon.Carbon is in good condition for reuse for optimum recovery.The pregnant solution is amenable to electrowinning or zinc precipitation to recover gold/silver from the solution.The whole process to be simple and short to reduce gold inventories.Present Elution ProcessesTable 1 shows some carbon elution processes that are available today. The two main elution processes used in the industry are: (1) the Zadra process, in which hot cyanide solution is circulated through an elution column and electrowinning cells; and (2) the Anglo American Research Laboratory (Anglo) process, consisting of a pretreatment step with caustic cyanide solution, followed by elution with deionized water."

Jan 1, 2000

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

The discussion which followed the publication of my paper by the formert has, I think, enhanced its value. It may therefore be of interest to members of our Australasian Institute, who are not members of the Institution of Mining and Metallurgy, if I give a synopsis of the discussion.My attention was drawn to the fact that my paper did not make clear the extent of the improvement in furnace operations, which followed the use of coke of high quality; this comment applied more particularly to the lead content of slag. My failure to supply comparative figures in regard to the lead content of slag was governed by a condition which, I think, is of interest to metallurgists. As a result of industrial...

Jan 1, 1932

By O. R. Eckstrand, M. Asif, P. L. Schwann, A. J. Naldrett, R. J. F. Scoates

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. PGE-bearing sulphide mineralisation is contained in the lower 600 m of the Upper Central Layered Zone of the intrusion. There are four regimes with distinctive crystallisation characteristics. PGE content is low, both in bulk rock and in terms of metal in 100% sulphides, in the sulphide-rich cumulates but increases sharply in the sulphide-poor cumulates at the base of regime 1. Increases in regime 2 have no such clear relationship with incoming cumulus sulphides. PGE contents are low throughout regime 3, but regime 4 has sulphides with high PGE content, decreasing rapidly upwards, at the base of many of its cyclic units. The observations are interpreted as indicating that sulphide saturation occurred in the middle of a cyclic unit in regime 1, after which fractional segregation of sulphide caused a systematic decrease in PGE content. The resulting contrast between 40 000 ppb PGE in sulphides below the mineralised zone and less than 1 000 ppb above is of practical importance in exploration for such zones. In regime 2 the magma chamber was open to fresh influxes and PGE content was not so sensitive to sulphide saturation. In many regime 4 units influxes of new magma caused immediate sulphide saturation and PGE depletion, so that PGE-rich cumulates do not underlie PGE-bearing sulphide zones. Theoretical analysis indicates that regime 1-type behaviour is likely to characterise intrusions below the level at which plagioclase has entered as a cumulus phase and regime 4-type behaviour above

Apr 1, 1994

I find that during the short time I have been in this district, the majority of boilers are, and have been, receiving very bad usage owing to the difficulties which they have to contend against, viz., oil and bad water. Oil on the heating surface of a boiler is of a highly dangerous nature inasmuch as it allows the surface to become overheated, owing to the water not coming into direct contact with the plates, and it naturally follows that when the crown sheets of a flue or firebox become overheated, you lose a considerable amount of the strength of the plate, and the flue or crown comes down. Referring to the oil question, I find that too much care cannot or exercised on the part of engine drivers in order to minimise as much as possible the internal lubrication of the various engines under their control. For I consider that it is here that the most of the trouble is caused. My reasons for stating such to be the case, are:-That the majority of enginedrivers before coming to this field have been used to driving engines that have been exhausting into the atmosphere, and probably they have been taught that it is far better to use a little extra lubrication than to have a hot bearing. So far so good. But one thing that must not be overlooked is that on these fields the conditions are altered in this respect, as the majority of engines in this district are not exhausting into the atmosphere, but are condensing their exhaust steam and using the water so condensed for feed purposes.

Jan 1, 1901

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

Variations in delay timing can have a marked influence on blasting effectiveness and, hence, on total production costs. In single-row bench blasts, delay firing is invariably more effective than simultaneous initiation. In single-row delayed blasts, there is an optimum inter-hole delay above and below which inferior blasting results are obtained. This optimum delay is equal to the time required for each charge to just effectively detach its quota of the burden. The inter-hole delay should seldom be less than 4 ms.m-l of burden.In multi-row blasts in which holes in a given effective row are fired on the same delay, the entire burden on any effective row should be detached from the rock mass just before charges in the next effeotive row detonate. Delays shorter than this give inferior blasting results and an increased likelihood of environmental and slope stability problems. If the inter-row delay is too long, cut-offs can occur, especially where the delay unit is located outside the blasthole. For a surface delay system, the optimum inter-row delay usually varies between 4 ms.m-l and 8 ms.m-l of effective burden. The number of rows that can be fired effectively with surface delay systems (in a single blast) is limited by the threat of cut-offs. Greater interrow delays and a larger number of rows per blast can be fired to advantage with down-the-hole delay systems.There are practical limits to the timing accuracy of all available delay systems. The existence of delay time variability should be recognized and duly considered in the design of blasts.The relationship between delay timing and blasting vibrations is not discussed.

Jan 1, 1977