Search Documents

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By James C. Sever

The mode of operation of dolomite kilns at a magnesium reduction plant using the Magnatherm process was designed to minimize operation cost and maximize kiln refractory life. Analysis of downstream operation issues shows the quality metric for dolime changed from loss on ignition to specific surface area. This produced a complete change in kiln operation; the net results being major plant productivity increases decrease in operating cost, and increases in both kiln operating costs and reline frequency.

Jan 1, 2015

By Yuanbo Zhang, Daoyuan Zhang, Youlian Zhou, Guanghui Li, Tao Jiang

"Modified humic acid (MHA) has been developed by Central South University (CSU) and authorized in China. It has been reported that MHA is an effective binder for oxidized pellets prepared from specularite concentrates. In this research, effects of MHA binder on roasting behaviors of the specularite pellets are studied. MHA is an organic binder, containing much carbon, hydrogen, oxygen, etc. During the roasting, MHA can provide some heat because of combustion of hydrocarbon, which is beneficial for the recrystallization of Fe2O3 in the specularite pellets at high temperature. Simultaneously, part of hematite particles within the pellets are firstly reduced to magnetite, then, magnetite is oxidized into secondary hematite, which obviously improves the roasting performance of specularite pellets.IntroductionOxidized pellets have been widely used in steel production as a kind of high quality burden for blast furnace ironmaking [1]. In recent years, production of oxidized pellets is developing very fast. Therefore, the supply of high quality magnetite concentrates, which is the most suitable for pellet production, becomes scarce. It is imperative to pursue new alternative materials for oxidized pellet production [2]. Specularite concentrates have attracted widespread attention due to the advantages of high total Fe grade and low impurity content. However, due to the poor ballability and firing performance, specularite has not yet been widely applied into pellet production [3, 4]."

Jan 1, 2012

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"Direct digital manufacturing offers promise as a technique for fabricating complex hydrogen purification membrane support structures. Free form fabrication methods can produce parts with complex structures, and sintering parameters can be controlled to adjust the density, pore structure, pore pathways and strength in catalytic substrate constructs. Efforts are underway to define the influence of selected process variables on the chemical and mechanical properties.IntroductionThe Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production. Because hydrogen readily passes through palladium, a structurally sound palladium-based membrane is capable of separating relatively pure hydrogen from other gases. In order for this technology to succeed, a suitable substrate material must be identified.High purity hydrogen is produced by various means. A common method involves a two-stage process for separating hydrogen from a hydrocarbon gas stream: 1) hydrogen-rich syngas is produced by the catalytic reaction of natural gas or another light hydrocarbon gas with steam, and 2) hydrogen is separated from the other syngas components by pressure swing adsorption (PSA) (US. Energy Information Agency, 2011). In PSA, gases enter a column that is packed with a material that absorbs gases as the chamber is filled and pressurized. As the pressure is slowly relieved, the absorbent material releases hydrogen at a higher pressure than the impurity gases. PSA processes produce 99.99% pure hydrogen at a high recovery rate. These systems typically demand a high capital investment due to the high pressure and multiple stages (columns) needed to attain high hydrogen production rates.Research geared toward reducing hydrogen production cost is focused on the development of improved catalysts and adsorbent materials as well as more effective single-stage separation processes. An interesting method combines hydrogen reduction catalysis and filtration. Nascent hydrogen is separated from other gases as it selectively permeates the filter. Catalyst filters may be made of gold, silver, platinum, palladium or precious metal alloys (Davis, 2009)."

Jan 1, 2012

By Jun Deng, Daohong Wu, Zhicheng Cao, Jingkun Tang, Luxing Feng, Xun Xue

The effect of reducing temperature, H2/CO mole ratio, and reduction gas flow rate on the metallization rate of oxide pellets were investigated at laboratory scale, with ludwigite iron concentrate used as raw materials. The reducing temperature varied from 850 to 950 °C, the H2/CO mole ratio changed from 1.5 to 4.5, the range of reduction gas flow rate was from 2 to 5 L/min. The results indicate that the metallization degree of pellets increase with increase of the temperature, H2/CO mole ratio, and gas flow rate. However, after temperature rises to 850 °C, metallization degree increases slowly. The effect of H2/CO on the metallization degree is not very obviously with the ratio of H2/CO increasing from 1.5 to 4.5. When the gas flow rate was increased from 2 to 3 L/min, the metallization degree increased greatly from 72.2 to 92.1%. In the flow range from 3 to 5 L/min, the metallization degree was increased slowly. The results obtained could be useful for comprehensive utilization of ludwigite iron concentrate by gas-based direct reduction method.

Mar 1, 2017

By C. M. Dentan

Conventional testing of crude kaolin ores emphasizes physical properties as they relate to end uses of kaolin products. This approach to evaluating crude ores does not reveal the basis of behavioral differences between typical coarse and fine kaolins from central Georgia. Optical and scanning electron microscopy in combination with XEDS have been employed to characterize both coarse Cretaceous and fine Tertiary kaolin in order to shed light on the reasons for the gross differences in their properties. Routine evaluation of various parameters was also carried out. Bulk densities were 1.48 g cc-l for the coarse clays and 1.53 g cc-1 for the fine clays. Surface areas were 15 m2 9-1 and 25 m2 9-1, respectively. Brookfield viscosities were low for the coarse clays at 70% solids, and high for the fine clays. The situation was reversed for Hercules viscosities. Sixty percent of the coarse clays had particles of less than 2 um and the fine clays had 90% less than 2 cm. Micrographs of thin sections prepared from blue-dyed epoxy-impregnated crude ores and of SEM fabric samples demonstrated vivid differences in texture. Cretaceous kaolins appeared to be completely recrystallized residual products of former aluminous sediments, while Tertiary kaolins retained their essentially sedimentary character. Differentiation of the coarse and fine kaolins is rapidly accomplished by both optical and scanning electron microscopy, and should be considered a valuable analytical technique in evaluating kaolin ores.

Jan 1, 1981

By Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Zengqing Sun, Yanfang Huang

"Because of small specific surface area and poor ballability, vanadium/titanium-bearing magnetite is difficult for production of oxidized pellet. A novel organic copolymer binder, modified humic acid (MHA), has been authorized recently in China. Effects of the novel MHA binder on the quality of V/Ti-bearing magnetite pellets are studied in this paper. Experimental results show the MHA binder can obviously improve the strength of green pellet. Because of better heat endurance, the MHA binder pellet has a higher strength than Peridur pellet under the same preheating conditions. Moreover, TFe grade of pellet with the MHA binder is much higher than that of the bentonite pellet. The strength of preheated pellet containing MHA binder of 0.25%~1.0% meets the requirements of oxidized pellet production by grate-kiln process. Comparatively, MHA is a promising orgainc binder for iron ore pellets. Its price is only one tenth of Peridur price and about 3 times of bentonite price.IntroductionThe iron-making practices show that the use of pellet is beneficial to blast furnace life, productivity and fuel savings. Therefore, many iron-making plants have expanded the production of oxidized pellets in order to meet the needs of modern large-scale blast furnaces [1]. Presently, bentonite is widely used to improve the quality of iron ore pellets. The negative effects of using bentonite include decreasing total iron (TFe) grade and degrading the metallurgical properties of the final products [2, 3]. Many studies, therefore, have been conducted on the application of organic binders to overcome the weakness of the inorganic bentonite. In comparison with inorganic binders, one of the biggest strengths of organic binders is low residual silica content [4]. However, those studies showed that the economics of foreign organic binder addition into pellets was not attractive. For example, the compression strength of preheated pellets and roasted pellets are both too low, resulting in powder generation and ring formation in the industrial rotary kiln [3, 4]."

Jan 1, 2011

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinter should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified. In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinler should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified, In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Ming-Feng Ye, Guang-liang Wu

The microstructure and mechanical strength variations of chromite pellets preheated and roasted in air were studied systematically. The results show that the chromite (Fe,Mg)(Cr,Fe,Al)2O4 is oxidized to magnesium-rich (Mg,Fe)(Cr,Fe, Al)2O4 and ferrochromium complex oxide (Cr,Fe,Al)2O3 in the preheating process over 500 °C. When the temperature is higher than 1000 °C, the new phase (Cr,Fe, Al)2O3 is formed, which is mainly distributed in the outer layer of a single chromite particle. Inner the particles there are acicular (Cr,Fe,Al)2O3 and unoxidized (Fe,Mg) (Cr,Fe,Al)2O4, which forming an interwoven structure together. The oxidation rates of pellets can reach to superior limits in 20 min. With the temperature increasing from 950 to 1300 °C, the mechanical strength and oxidized rates increase to varying degrees correspondingly.

Mar 1, 2018

By Masahiro Hirasawa

"As a fundamental study on pyrometallurgical process that involves recycling steel-making dusts, of which major components are oxides of Zn and Fe, and waste polyvinyl chloride simultaneously ·at. a temperature below 1273 K, the reactions between the mixture of ZnO + Fe20 3 and PVC or the compound ZnFez04 and PVC are investigated in a series of thermogravimetric and small scale reactor experiments under inert atmosphere at below 1273 K. The reaction mechanisms are discussed· on the .basis of the thermogravimetric data. From the results of reactor experiments, it is shown that the chlorination of Zn in the oxides by Cl in PVC, the vaporization of ZnC12, the reduction of iron oxide to metal Fe by C and H in PVC, and, thereby, the separation of Zn and Fe in the oxides take place simultaneously at the temperature ~= 1200 K.IntroductionSteelmaking dusts are metallurgical wastes consisting mainly of oxides of Zn and Fe with smaller amounts of other heavy metal elements, such as Pb. In the recent investigation, [1] the present authors have investigated the fundamental aspects of a potential pyrometallurgical process· of recycling steel-making dust with polyvinyl chloride (PVC) at temperature T < 1273 K under Ar atmosphere. The performance of a similar process, in which HCl in the combustion gas of PVC is used to chlorinate Zn in the EAF dust under oxidizing atmosphere, has been investigated by Tailoka and Fray [2] with fundamental experiments. Figure 1 shows an example of the potential ·diagram of Zrt-Cl-0 and Fe-Cl-0 systems. In the figure, we can find two regions where ZnCl2(g) can be separated from Fe containing compounds. One is ZnCiz-Fe20 3 coexistence region at higher oxygen and chlorine potentials and the other is ZnCl2-Fe coexistence region at lower oxygen and chlorine potentials. The process adopted by Fray and coworkers is aimed mainly at the performance of Zn/Fe separation in the higher oxygen potential region. In the present study, the lower oxygen potential region is focused on."

Jan 1, 2000

By Shusen Cheng, Kun Yan

A three-dimensional mathematical model of hot blast stove pipe shell has been established and used for analyzing the stress distribution and deformation. The results show that stress concentration happens along the intersection line of hot blast main and the hot blast manifold. There is no plastic deformation on the whole pipe region. The shell near the intersection elongates along the vertical direction and shortens along the horizontal direction, and deforms into an oval. The shell of hot blast main rises up, and inclines upward around the end of hot blast main. The hot blast main moves away from the hot blast and the displacement near the middle region is larger, the main deforms into an arch on horizontal surface. The deformation of shell may form a gap between shell and refractory inside and damage the security and stabilization of hot blast stove piping.

Mar 1, 2017

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"Fine manganese fines are characterized by large amount and low price compared to lump manganese ores. However, fine manganese must be agglomerated as EAF (electric arc furnace) feed. In this paper, high quality fired pellets were produced by simulating grate-kiln process to supply the feed for EAF from some imported manganese ore fines containing high combined water. Manganese ore fines assaying 44.47wt%Mn, 5.89wt%Fe, 12.09%LOI and with 72.7wt% ranging between 0.5mm and 8mm, are pretreated up to the particle size of 84.7wt% passing 0.074mm by HPGR (high press grinding roller) twice in open circuit. The finely ground manganese fines were mixed with 1.2wt% bentonite, balled at 15% moisture for 7min in disc pelletizer. The drop numbers, compressive strength and thermal shock temperature of green balls reach 11 times/0.5m, 11 N/pellet and 360oC, respectively. After the green balls drying in the oven, the dry pellets were preheated at 1050oC for 12 min and then fired at 1300oC for 12 min in electric tube furnace. The compressive strength of fired pellets reaches 2621 N/pellet. Therefore, these pellets are high quality burden for blast furnace or EAF due to high mechanical strength and high Mn grade of 49.11wt% and low detrimental elements.IntroductionManganese, mainly using as deoxidizing agent, desulfurization agent and alloying elements, is widely used in the steel company. With the rapid development of iron and steel industry in China, domestic manganese ores cannot meet the requirement, resulting large quantities manganese ores import to China [1-4]. Compared to lump manganese ores, fine manganese ores containing high combined water are characterized by large amount and low price. However, they must be agglomerated as EAF (electric arc furnace) feed. There are three ways to agglomerate the manganese fine ores, sintering, briquetting and pelletizing [5-6]. Compared to the other two methods, pelletizing technology possesses the following superiorities, such as uniform size distribution of product, stabilizing chemical composition of product and lower energy consumption in producing. Therefore, pelletizing is a superior way to treat the fine manganese ores [7]. The systematic research of producing manganese oxide pellets by fine manganese ores containing high combined water was studied in this paper."

Jan 1, 2011

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By Shiju Zhang, Yongnian Dai, Songli Liu, Kuisong Zhu, Wenhui Ma, Li Cao

There is an abundance of vanadium-titanium magnetite in Panzhihua, China, which contains more than 8.73 x 10^8 tons of TiO2 accounting for 90.6% of the national reserves. To fully utilize Panzhihua titanium resources, many processes were proposed. The present status and future development of technologies for comprehensive utilization of vanadium-titanium magnetite including blast furnace, electric smelting, and ilmenite upgrading processes are reviewed.

Mar 1, 2017

By T. P. R. de Jong

Dual energy X-ray transmission imaging is extensively applied for safety luggage inspection. Its advantages are its rapid scanning rate (25 to 100 cm/sec) at approximately I mm resolution and simultaneous thickness independent metal identification. This is especially advantageous for secondary scrap metal inspection and automatic sorting. Other applications include metal product inspection, bale control, and waste processing. Recent progress in development of an automatic on-line sorter for bulk solids is presented and discussed. Besides various non-metal applications (solid fuels, wastes etc.) it appeared particularly effective in light metal sorting. As inspection tool better control of difficult to monitor solid bulk streams, batteries, bales and other related metals becomes possible.

Jan 1, 2003

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983