Search Documents

By Bingyi Bai, Lifeng Yang, Yanling Guo, Jieyu Zhang, Guoding Gao

In terms of special resources with iron, niobium and rare earth coexisting in Baiyuneboite, the new smelting technology of ferrocolumbite was studied. Reduction experients for the Baiyuneboite and explores ore phase change of Baiyuneboite in the process of reduction was conducted with graphitic carbon as the main reducer and a temperature below 1000 ℃. Moreover, it studies the influence of reducer, roasting temperature and grind fineness on the reduction as well as focuses on the evolution course of iron phase. Through the analysis on in-situ XRD of the raw ore and carbon addition ore, it also develops microstructure change rules of Fe ore phase and ore phase of paragenetic elements for composite ore(Ca, Si, Nb, F) in the process of reduction roasting. In addition, the impacts of temperature on the reduction process are also discussed. With regard to minerals of different particle sizes, the thesis will explore their ore phase changes and microstructures after 10 hours’ reduction under 900 ℃.

Jan 1, 2015

By Chen Song

Cobalt basic carbonate particles were precipitated from 1.0mol cobalt nitrate or cobalt sulfate solution with ammonia carbonate. By controlling the zeta-potential of the particles and the ionic strength of the solution, the uniform particles with ellipsoid or rod shapes were obtained. During the precipitation process, the interface tension was diminished to the minimum and therefore the Ostwald ripening and secondary nucleation were both inhibited. The morphology and the size control by zeta-potential seem to be the result of thermodynamics rather than classical crystalline kinetics. The particle sizes were in the range of 0.4-0.6, 0.3-0.4 micrometer. After thermolysis, the spinel-type C0304 particles were produced. The morphologies of C0304 particles were similar to that of their precursors.

Jan 1, 2003

By David G. Dixon

A mathematical model is derived in dimensionless form which simulates the effluent concentration response of reagents from spent heaps under both fresh and recycled water rinsing. The model is based on dispersion from isochoric pathways distributed in length and cross-section, oriented normal to convection channels in ideal plug flow. The effects of heap height, rinsate flow, and initial reagent concentration are examined. It is shown that the rinsing cycle undergoes a distinct shift between fast and slow rinsing at a certain time depending on the amount of stagnant solution in the heap, and the distribution of dispersion pathways. Results of preliminary column rinsing tests on both agglomerated and unagglomerated ores are presented which partially validate the model.

Jan 1, 1994

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By Nagy El-Kaddah

One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100µ inclusions are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate ?the capability of the system for producing super-clean metals.

Jan 1, 1996

By Stefan Mutl

By the term sorting one understands the separation of a material mixture into two or several products according to different material characteristics in the preparation technology. The oldest sorting procedure, the handpicking, is less and less used to separate different material mixtures because of the considerable personnel expenditure and the strict hygienic regulations at the workplaces in Europe. In general, the manual assortment is able to solve separation tasks, which could not be solved by machines so far. The picking is one of the most selective processing methods. However, the progress in the computer and sensor engineering today makes the creation of automatic picking devices possible, whose efficiency goes far beyond the possibilities of handpicking. Therefore in the future automatic picking will not only be applied to already common applications like the waste glass assortment by colour, but also to the assortment of complex composed material mixtures e.g. old shreddered cars. Thus, the automatic picking, supported by high performance computer systems and new sensor technology, gains more and more significance within many applications of waste processing. However, in order to apply automatic sorting procedures for different material streams within recycling processes, a substantial research and development need still is existing. The desire of the users is to sort more extensively in order to achieve products with bigger material varieties, In addition, the requirement of the accuracy of recognizing and sorting out of single grains rises, This lecture illustrates the procedure of the hand picking before it was employed in waste processing. Thus, a renaissance of a long forgotten method is happening in terms of today's state of the art procedure "automatic picking". Possible technologies, fields of application and future potentials of this technology are pointed out.

Jan 1, 2003

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By C. M. Antony

The galvanizing process involves the use of accessory equipment in a series of aggressive environments including zinc ammonium chloride flux, molten zinc at 45S°C (850°F), and acid for stripping of adherent zinc. An Fe-Ni-Cr-Co alloy has been identified which combines excellent strength and resistance to molten zinc and acid attack making it suitable for accessory equipment. The alloy was field tested by a commercial galvanizer as basket material and was found to provide improved life compared to original low-alloy steel baskets while cross-section thickness was reduced 44%. Additionally, other associated processing cost savings were realized.

Jan 1, 1992

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993

By Ramiro Escudero G.

Since the introduction of column flotation almost forty years ago the column technology has grown into several non-mineral applications such as among others the effluent treatment, soils recovery and de-inking of recycled paper. Recent studies have demonstrated that particular characteristics of the dispersion (bubble size, gas holdup, bubble surface area flux) are needed for a given flotation column duty. In this work, two kind of spargers were tested (i.e., internal and external) using a 4 inch column lab in a two phase system. Results show that the external sparger provides a dispersion with characteristics that include those produced by the two internal spargers.

Jan 1, 2003

By Chuanguang Bi, Wenbin Dai, Hongtao Wang, Mansheng Chu, Zhenggen Liu

Coke oven gas (COG) injection is considered as one of feasible measures to reduce carbon emission of BF. The effects of COG injection on the reduction of iron-bearing burdens were numerically simulated by means of multi-fluid BF model, which revealed that with increasing COG injection rate, solid temperature gradually decrease, in-furnace H2 concentration increases, the reduction of magnetite and wustite by H2 is evidently accelerated, the reaction rate of wustite by H2 reduction is enhanced and the reduction degree of mixed burdens is strengthened. Under this hydrogen-enriched condition, metallurgical properties of iron-bearing burdens were experimentally investigated. The GB/T13242-91 test results showed that with increasing COG injection rate, the reduction swelling index of oxidized pellets decreases while the reduction ratio of pellets increases. The softening-melting tests suggested that softening interval of mixed burdens increases from 163.6 to 228.3 °C while melting interval decreases from 147.3 to 92.4 °C. The cohesive zone moves downwards and becomes narrow. The permeability of mixed burdens is improved. In terms of metallurgical properties of iron-bearing burdens, COG injection benefits to improve BF performance.

Mar 1, 2017

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

By Marco Antônio Siqueira Rodrigues

The possibilities for treating rinse waters fiom chromating bath by electrodialysis are discussed together with the possibilities of optimizing the treatment process for waste reduction and reuse of water and chemical products. An industrial effluent with 4600 ppm of Cr(VI), besides other metallic contamination, was used as work solution. This solution has been recirculated on an electrodialysis cell of three compartments, using exchange membranes Selemiom AMT and CMT. A migration of dichromate ions into the anodic compartment was obtained, so that an extraction of circa 99.9 % of Cr(VI) present on the solution was observed, resulting in water with a Cr(V[) concentration of 4 rnd. These results show that electrodialysis can be used to treat these effluents, and this water could be reused as rinse water. The solution of the anodic compartment, consisting at the beginning of the experiment of H2S04, 0.1 N, reached 7200 mg/l of Cr(VI). This concentrate could be reused on the chromating bath itself.

Jan 1, 1999

By P. F. Stratton, M Huggahalli, N Saxena

"Several studies have been carried out to determine how the optimum atmosphere conditions in the heat treatment of metals can be established for a given product by using different gas injectors and varying atmosphere flow rate and composition. The most common approach taken to gain insight into furnace atmospheres has been to use commercial computational fluid dynamics codes and examples of their use are shown. However, the complexity of these codes, the difficulty in establishing boundary conditions, their cost and computational demands limit their usability in solving day-to-day production problems.A simplified, web-based model of a furnace atmosphere is described where the conservation equations are solved to determine the composition profiles of the atmosphere in the furnace. Although the model is restricted in scope to certain types of furnace, it is shown to give better results than CFD when boundary conditions are uncertain. The application of the model to the understanding of existing furnace conditions and to determining ways of optimising the use of gases are discussed. IntroductionThe important role of protective atmospheres during heat treatment of metals, furnace brazing of assemblies and soldering of printed circuit boards is well established. The atmosphere in the furnace prevents air ingress and oxidation of the parts, helps flush away any flux or binder from braze and solder pastes and provides an important mode of heat transfer [1]. In a batch furnace having typically one or two gas injectors, the gas utilisation and process can be optimised by minimising air leaks and mantaining atmosphere homogeneity with fans or other atmosphere circulation techniques. In a continuous furnace, however, atmosphere optimisation is more difficult as furnace inlets and exits can also let in air. The atmosphere requirements of different stages of heat treatment, brazing or soldering vary [2]. Achieving these atmospheres in different sections of the open-ended furnace is a relatively complex task. Methods such as atmosphere zoning and the use of physical curtains and gas injectors have evolved with time, though it is hard to predict how effective these techniques will be for a given furnace and process. Experts in the field tend to rely on experience and rules-of-thumb rather than scientific method to achieve the required results."

Jan 1, 2001

By Haibin Wang, Baojun Zhao, Xueyi Guo, Zhixiang Cui, Zhi Wang

In conventional copper production, anode copper is produced from concentrate in three furnaces in a process that entails four oxidation steps and one reduction step. Three types of slags are produced that require further treatment to recover copper. Dongying Fangyuan Nonferrous Metals recently developed a simplified process which requires only two custom-designed furnaces instead of the conventional smelting, converting and re fining furnaces. The first furnace continuously produces high-grade matte (>75 wt% Cu) that contains little iron (<2 wt% Fe). The liquid matte is continuously fed to the second furnace, which produces anode copper. The new process signi ficantly reduces the capital and operating costs and increases productivity and environmental sustainability. This paper presents fundamental concepts that enable the simpli fied process to be developed. The detailed operations in Dongying Fangyuan Nonferrous Metals are also described.

Mar 1, 2018

By R. V. Kumar

"The use of sensors to monitor gaseous species in industrial processes is discussed. All of the existing systems have disadvantages. Sensors, based upon solid electrolytes, which can be placed directly into the gas stream are attractive but many also respond to oxygen, need to be sealed at high temperatures and require a separate reference. This paper describes sensors, usually based upon two electrolytes, which do not respond to oxygen and do not require high temperature gas seals or separate references. The application of these sensors to the measurement of carbon dioxide, sulphur dioxide and trioxide and hydrogen chloride is described. These sensors can be placed directly into the gas stream at elevated temperatures.IntroductionOn-line gas sensing is becoming more important as concerns regarding the environment mount. There are many established techniques for monitoring gases in industrial processes, with applications in safety monitoring, chemical analysis or process and emission control. Flue gas analysis involves the greatest technical complexity, requiring several sophisticated capital-intensive spectroscopic instruments for different species as well as needing highly skilled operators. There are also several instruments, based upon aqueous electrochemistry, which are available for the analysis of the gases S03, S02, N02 but these require that the gases are sampled at high temperature and cooled, prior to analysis. These instruments cannot be considered as giving on-line measurements of the gas composition. Furthermore, the power requirement of these instruments frequently precludes battery operation for field and domestic use."

Jan 1, 1997

By Mathilde Guilpain

A wide variety of plants are able to extract nickel (Ni) from soils and accumulate this metal in their foliage. Hydrometallurgical processes have been developed to recover Ni in the form of metal or salts, starting from the plant A. murale. They include: (1) a combustion step, to obtain ash containing 15–20% Ni; (2) a leaching step; and (3) purification. That whole flowsheet has been thoroughly investigated, and the processes scaled up to the pilot scale. Another strategy is presented here, consisting of recovering Ni without burning the plant. Ni can be extracted from the dry plant by water leaching, but the leachate is a multi-element solution from which Ni has to be separated. Selective precipitation of Ni hydroxide is not possible since Ni is bound to organic ligands. In this work, the plant leachate is processed by adsorption on the chelating resin DOWEXTM M4195. The results showed that Ni was selectively retained whereas the other main cations were not. Nickel could be recovered at the elution step. This methodology needs to be further investigated but these initial results are very encouraging and open the possibility of Ni recovery by agromining.

By D. P. Cook, Jr. Jones, J. W. Evans

"It is well understood that the flow of liquid metal in the mold region of the caster can have a notable effect on the overall solidification behavior in aluminum casting. Previously our group has characterized the flow in this region in a water model, using particle imaging velocimetry. The flow is significantly effected by the specifics of the metal delivery system, i.e. size, geometry, used during the cast. Recently, a time-averaged 3D numerical model of the nozzle, combo bag and sump region has been developed and its validity has been tested against experimental data. Cases were run for different sized combo bags as well as bags that have been blocked. The results show satisfactory agreement between the physical and mathematical models.IntroductionFluid flow in the head of an electromagnetic (EM) and direct chill (DC) ingots has been shown to effect many important operational parameters in casting such as superheat removal, macrosegregation, and hot cracking. In most cases, the momentum from the nozzle is diverted through a delivery system, termed a bag, before entering the mold region. The specific geometries of the bags vary widely from operator to operator suggesting that there is still some question as to the optimum design. Several studies [1-4] have been carried out to understand the influence of the bag design on the solidification behavior in aluminum casters. However, few studies have included numerical prediction with experimental verification. Unfortunately, many simulations performed today still do not accurately account for flow in such devices.Recently, a significant amount of research into the flow resulting from the metal delivery systems has been performed [5-8]. The thrust of this research has been characterizing the flow patterns by a measurement technique called particle imaging velocimetry. The data suggest that the method of delivering the liquid metal into the mold region has a significant effect on the nature of the flow. With a detailed set of quantitative data from a water model, a numerical model can be built and tested to ensure a proper description of the flow field. The computational model used in these simulations is designed to represent a laboratory scale model of a caster in which ""combo"" bags were simulated. Such bags are mostly of a densely woven glass fiber material with low permeability to aluminum. ""Windows"", of a more open weave, permit aluminum to flow from the bag, see Fig. I. Two different sized combo bags were modeled, each subject to two different outflow window configurations. Furthermore, experimental measurements [9] were used to validate the model results."

Jan 1, 1999

By Yoshifumi Abe, Akinori Toraiwa

"Nippon Mining & Metals started a new copper anode slime treatment plant that processes slimes in a chloride media. The basic plan of the process was proposed by Mr. James E. Hoffmann and Nippon Mining & Metals modified and advanced to produce precious metals in acceptable qualities for the company. The process has a wet chlorination stage of decopperized slimes, a solvent extraction and a reduction stages of gold, a silver chloride reduction stage and separative reduction stage of its gold extraction raffinate. The new plant of this process started in 1997 and has been operated in good condition.IntroductionThe old anode slime treatment plant of Nippon Mining & Metals, located in it's Hitachi Refinery, processed anode slimes through a combination of pyrometarllurgical processing and electrorefining. There was a need to plan a future of the plant because the maintenance cost increased year by year and a new selenium registration was going to be applied to the plant. Some plans were discussed and the result was that the process proposed by Mr. Hoffmann was superior among them.Nippon Mining & Metals started 'to examine the process and the experimental result showed that the process had an ability to be its new process but further research should be necessary to produce precious metals in acceptable qualities. The final process flow has some modified and additional stages to be suitable for its requirement. Silver processing stage is quite changed. Gold extraction stage has a new step to polish gold loading DBC. Gold extraction raffinate treatment stage is advanced to be able to recover precious metals, selenium and tellurium, separately. Aeration under atmospheric pressure is employed in decopperizing stage.The basic design of the new plant started in 1995 and finished in 1997. The construction of the new plant began in April 1997 and finished in October. The plant has been operating well after the four months test operation."

Jan 1, 2000

By Darryl Lovato, Ramiro Pereyra, Daniel S. Schwartz

"During an annual inventory of nuclear material, a plated steel container which contained plutonium oxide failed. The container had been packaged for temporary storage but had been overlooked and remained in storage for more than 23 years. Although it was determined that the failure occurred through the slip-top rim, a metallurgical evaluation was requested to help to determine the integrity of the container.Optical metallography and scanning electron microscopy were used to analyze the character and degree of corrosion in the container. The depth of corrosion, measured at approximately 10 µm, did not pose a threat to the integrity of the container. However, the corrosion morphology and chemistry did suggest that a galvanic cell had developed between the tin and steel from the condensation of water. The morphology also suggests that the attack of the steel took place over a series of cycles due to changes of the environment.IntroductionMetallographic analysis was requested as part of the investigation into the mechanism of the failure of a slip-top container (#38621) containing plutonium oxide (PuO2) powder. The container had leaked during a special nuclear material (SNM) annual inventory causing contamination and closure of the vault. A photograph of the container and interior container is shown on the right in Figure 1. An initial investigation established that the source of contamination was the consequence of the failure of multiple layers of containment. Initially by the deterioration of the interior plastic bottle and polyvinyl chloride (PVC) bagout bag, and finally through the lid and steel container interface at a location where tape had not adhered properly [1]. Although the source of the breach was established, it was determined that metallographic analysis was important to establish the extent of deterioration of the steel container."

Jan 1, 2008