Search Documents

By Gregory Owen Lewis, Mark William Johns

The use of resin-in-pulp (RIP) to recover dissolved metal ions from slurries is receiving increasing attention. A number of engineering aspects have been identified as crucial if a RIP sys­tem is to operate efficiently. These are the mixing of the resin and pulp, the transportation of the resin and pulp and the sepa­ration of the resin from the pulp medium. Evaluation of numer­ous alternatives revealed that air agitation is the most suitable means of mixing to effect uniform distribution of the adsorbent and to effect a high mass transfer rate, airlift pumps are the most effective method of transporting the slurry particularly as they are characterized by a low degree of resin degradation and sieve bends are the most suited means of effecting the resin/pulp sep­aration. This paper details the design of the reactor that incorporates the three identified unit operations and presents data obtained from the contactor when operated at a throughput of I 00 000 t/m. The airlift pump was found to be sensitive to pulp density and submergence ratio. The screening ability of the sieve bend was influenced by resin and the pulp density . The reactor is a cost effective, metallurgically efficient unit for the recovery of metal ions from high density slurries.

Jan 1, 1996

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

Jan 1, 2006

By Keith Whiting

The Van Stone zinc-lead mine is located in northeastern Washing- ton in Stevens County. It is about 24 km (15 miles) south of the Canadian border and 48 km (30 miles) west of the Idaho line. The deposits occur in late Cambrian age limestones and dolomites of the Metaline Formation. The bedding controls the trend of the zones containing the lenses of zinc-lead mineralization. The Van Stone property and vicinity is almost entirely covered with glacial drift averaging perhaps 6 m (20 ft) in thickness. Outcrops are very sparse. Outcropping gossan with zinc mineralization was first discovered by George Van Stone in 19 13, in what is now known as the South Ore Zone. Only minor trenching was done at that time. The property was idle until the mid- 1920s when Hecla Mining Co. drove several short adits and performed minor diamond drilling. In 1938, Willow Creek Mines of Nevada Inc. acquired the Van Stone plus adjacent parcels and commenced drilling on the known South Ore Zone. In the course of an expanded drilling program, the nonoutcropping North Ore Zone was discovered and was drilled out along a N30°E strike for about 305 m (1000 ft), beyond which point no mineralization was intersected.

Jan 1, 1991

By Jaroslav Vicek, Alois Adamus

In the Czech Republic nitrogen was first used for the fight against the mine fire in 1949 (Hajek,1969). In the years 1949¬1996 the consumption of nitrogen in the Ostrava-Karvina Coal Basin /OKB/ reached more than 220 mil. m-3. The main source of nitrogen in the OKB is a central pipeline now. Gas nitrogen is used for the prevention of spontaneous combustion in gobs of longwall faces. The nitrogen infusion technology (Froger,1985), often called "franca technology", has been applied in the Czech coal mines since 1982. The aspects of the nitrogen infusion technol¬ogy can be theoretically solved by the calculation of mixing two gas streams in the filtration space. Longwall faces are parts of the ventilation network of the coal mine. The intake airflow of the longwall face is divided into the airflow passing through the face and a part of air losses passing through the gob. Air leakages through the gob and nitrogen in¬jected into the gob mix there. There is the main problem to solve air leakages in the gob. Usually, the principles of the gob aerody¬namics were used by many authors (Glusberg,1988;Voracek, 1994; Sulkowski,1993; Michailov, 1995; Dziurzynski, 1995; Kolarczyk, 1995; Saghafi, 1995; Sedlaty, 1993) that are applied to our case as well.

Jan 1, 1997

By D. A. Dahlstrom

Energy costs have had a serious impact on all basic industries today. This is due to the significant amount of energy that is used to convert natural resources into usable products. Other factors such as transportation with its major energy requirement and materials employed in processing that have already required significant energy input for their manufacture accordingly influence delivered cost to the user. The farmer is a good example of this. While his large capital investment for land, machines, and buildings is highly impacted by today's interest rates, his chemical fertilizer, herbicides, and pesticides as well as those same machines and transportation costs for his products have also been seriously affected by energy costs. With the many unit operations involved in mining and mineral processing, several of which require significant inputs of energy, one can only conclude that this industry has experienced a great increase in percentage of total cost for energy alone. Fuerstenau (1975) indicated that the minerals industry used about 12.5% of the total energy produced in the US. McNulty (1983) listed the total energy requirements for the production of 0.9 t (1 st) of various metals including the energy consumed in the manufacture of supplies employed, such as tires, explosives, chemicals, grinding media, etc. (Table 1).

Jan 1, 1987

By D. M. Walters, C. M. van der Vyver, L. J. deVulliers

The occurrence of underground fires in narrow tabular ore- bodies where high density timber support is used is a dangerous and disruptive occurrence. The containment and extinguishing of the fire remains a very important consideration in reducing not only the loss in production time but also in limiting the extent of the area damaged by the fire. Mindful of this, Gold Fields have adopted and developed the inert gas generator system from its origins in Poland for use in Group precious metal mines. The system generates an oxygen- deficient atmosphere which is introduced in the fire area after this has been sealed. A number of problems had to be overcome to operate this system successfully within the infrastructure of these mines. Of particular significance is the operation of a jet engine, the prime component of the system, at air pressures encountered below sea level. The modifications have been found to be satisfactory to the point where, since 1992, ten underground fires have been extinguished using this system. Invariably, the areas affected by these fires were extensive (over 1 000 000 m3) and required continuous operation of these units over extended periods of time (in some cases in excess of 400 hours).

Jan 1, 1997

By Douglas E. Rawling

The successful genetic manipulation of T. ferrooxidans is partly dependent on an understanding of the molecular biology of the organism. For optimum controlled expression of foreign DNA in T. ferrooxidans it is important that donor DNA is derived from bacteria that are genetically similar to T. ferrooxidans or placed under the control of T. ferrooxidans transcriptional promoters. Several structural genes and their controlling regions from T. ferrooxidans have been isolated and their DNA sequenced. These include the genes that encode the nitrogenase enzyme (nifHDK genes), glutamine synthetase (glnA gene) and the recA gene. These genes and the identical genes from a wide variety of other bacteria have been compared at levels of DNA sequence, protein sequence. Where possible, gene expression as well as transcriptional control and protein function of the cloned genes were tested in the enteric bacterium Escherichia coli. The two genes involved in nitrogen metabolism were either expressed or possessed the necessary elements for expression in other bacteria. In contrast the recA gene was not expressed in E. coli from its own promoter. The two gene products that would be tested (glnA and recA) were fully functional in E. coli. The relevance of these findings to the genetic manipulation of T. ferrooxidans is discussed

Jan 1, 1989

By Y. C. Kim, F. Szidarovsky

The technique of linear kriging as a grade estimation method of mining blocks is reason¬ably established in the mining industry. During the kriging process, negative kriging weights ([]i) are sometimes encountered. Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense. To guarantee nonnegative weights, an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of nonlinear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer, time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over-or underestimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1987

In the hierarchy of performing mine planning tasks, production scheduling is naturally at the bottom. Yet good production scheduling is probably the most demanding and difficult task to achieve for various reasons. Being the last task in the mine planning hierarchy, a proper production schedule must not only conform to both the long-range and the short- range mine plans but also satisfy many practical details that are unique to day-to-day operations. For example, the averages which were good enough for both long-range and short- range mine planning are no longer good enough for production scheduling. Instead, the variations become the overriding concern. The answer must also be obtained quickly and on time, thus adding another dimension to the overall problem. Because of these considerations, many production scheduling problems have been begging for solution during the past decade. Many attempts were made to solve the production scheduling problems in the past using computers and the available operations research (OR) techniques, particularly among academic groups. However, it is probably true that, compared with the current full-time computer usage in long-range and short-range mine planning, very little computer usage is being made in production scheduling to date.

Jan 1, 1979

By Alberto Tarsitani

The existing Rome-Florence railroad capacity is inadequate for the traffic volume. To increase this capacity and to reduce the traveling time the Italian National Railroad Administration has decided to provide an additional 400% of rail capacity. This new rail line will be known as the Direttissima Roma-Florence line. It is planned to operate the trains on this connection at speeds of 250 km per hr. Table 1 lists the main design characteristics. [TABLE 1. Design Characteristics Design speed250 km per hr Maximum inclination80 00 (0.8%) Minimum curve radius3000 m Minimum vertical curve radius30,000 m Maximum superelevation in curve 425 mm Type of rail60 kg per m welded] The new rail line will be connected to the existing one by means of high speed switches called "interconnections" so that parts of the new line can be used also by local trains. Construction works for this new line have been divided by the railroad administration into eight sections. Five of these have already been committed to joint ventures. Castiglione Tunnel is a part of the fifth section, 42 km in length, which has been awarded to Consorzio Ferrofir which is a joint venture composed of the construction firms of Astaldi - Di Penta - Lodigiani - Sogene.

Jan 1, 1974

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By Peter H. Grimley

It is important to realize that lending institutions have a very different risk-profile from that of an equity investor. For bank financing, a feasibility study must address the concerns of the lender and these can be summarized under the four 'PI Is: Project, Performance, Product and People. Generally, feasibility studies focus on the measurable project risks associated with a new venture, but frequently insufficient emphasis is placed on key risk areas such as ore grade and metallurgical recovery. Before accepting full or even partial non-recourse risk, financial institutions will demand evidence that the project was constructed according to specifications and within budget and that its Performance within agreed limits has been demonstrated. Product risk should be discussed in detail in any feasibility study. For industrial minerals, penetration of the market can be critical to success and for commodities with volatile prices, the sensitivity of the cash flow to a range of prices should be carried out. Methods of reducing price risk such as long term contracts or, in the case of gold, forward selling should be carefully evaluated. The People risk is rarely discussed in feasibility studies, but can be a key element. Few projects turn out to be faithful copies of the study and the ability of the operator to identify

Jan 1, 1988

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997

By S. Atak, G. Bulut

The xanthate adsorption mechanism on pyrite was investigated with an emphasis on solubility studies. Additionally, adsorption studies, Eh and infrared spectrophotometer measurements were performed. Pyrite floats at pH levels between 3 and 6 using ethyl and amyl xanthates with a maximum at pH 4. The solubility of pyrite in the absence and presence of xanthate was investigated in detail with respect to pH and conditioning time. Experimental results showed that the solubility of pyrite increases from 60 to 120 ppm (10-3 to 2x10-3 mol/ L) in the presence of xanthate at pH 3. Fourier transform infrared (FTIR) spectra of ferric xanthate, dixanthogen and pyrite conditioned with xanthate indicated that dixanthogen is the only species that can be determined on the pyrite surface. Adsorption tests showed that the highest level of xanthate adsorption was in the acidic range; yet higher adsorption densities were detected in neutral solutions compared to alkaline conditions. Electrochemical data suggest that the doubling of the iron concentration is due to the reduction of ferric ion to ferrous by xanthate while xanthate is oxidized to dixanthogen. Dixanthogen formation together with the hydrophobic iron hydroxy-xanthate complex on the surface is proposed to be responsible for pyrite flotation. Key words: Flotation, Pyrite, Adsorption, Xanthate, Dixanthogen

Jan 1, 2003

By James G. Donovan, Mario G. Karfakis

A large percentage of Southern Appalachian coal reserves are located in seams less than 36" thick. As thicker and currently more mineable deposits are exhausted, methods of underground thin-seam extraction must be developed. Past experience with highwall mining of thin-seam coal has indicated that recovery rates tend to be lower than in conventional operations. It is suspected that this will also apply to underground thin-seam mining, regardless of proposed technology or mining method. Backfilling is one alternative for thin-seam coal mining; although backfill has been used extensively in hard rock mining its use in coal mining has been limited. The ability of backfill to provide additional ground support may enhance coal recovery by allowing for the design of undersized pillars. Backfill is capable of providing additional ground support by restricting lateral deformation of surrounding coal pillars and roof. This additional support can result in significant increases in recovery from thin-seam coal deposits. However, the overall feasibility of backfill is dependent on the in situ behavior of the fill material, the properties of the fill, the effects of the filling method on the total mining operation, and the cost of filling per extra ton of coal recovered.

Jan 1, 2001

By Walter E. Cook

BOB FALCONER: Without further ado I'm going to introduce our first speaker, Walt Cook. Walt is president of Strata Resources and is here with his business partner Joe Nenni. Joe would you stand up here. You'll be on the tag-team with Walt. Walt and Joe are in a consulting business associated with coal as well as metal and nonmetal industries. Their presentation will be on gainsharing. WALTER COOK: How many of you have gainsharing plans in place currently at your location? [show of hands] A considerable number-more than about half the room. Of those plans, how many of them do you consider as meeting your needs and being successful? [show of hands, far fewer, general audience laughter] You have all at least heard the word "gainsharing." Some of you undoubtedly aren't quite sure what gainsharing is, while others obviously have gainsharing plans in place and are looking for ways to improve them. In the short time I have now I'll be able to give you a precursory look at gainsharing and some brief ideas on where to look to improve your current plans. Over the years, I've found that it is often best to explain gainsharing by comparing it to other forms of employee compensation

Jan 1, 1998

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By Severn P. Brown

Cement plants in the central Hudson River valley utilize limestones of the Helder-bergian Series of the Lower Devonian. Chiefly calcilutites, calcarenites, and cherty calcisiltites, these rocks represent progressively deeper environments, from lagoonal to neritic, with scattered reef deposits. Stratigraphic continuity is marked, and a layer-by- layer analysis shows strikingly constant chemical compositions. The structural picture varies from flat-lying and relatively unfaulted beds on the northwest, through gently folded and faulted beds on the north, to complex overturned beds with closely spaced imbricate faults on the south. Operating techniques are simpler in the north, where grade control is effected chiefly by the initial layout of the faces. In the south, grade control requires flexibility and frequent adjustment of faces or scheduling. A system of quarrying along strike has been developed, grade being computed from a cumulative foot-per cent graph of the critical oxides in each mappable layer. Balancing shovel production among the many faces is simplified by comparing production requirement ratios with ratios of the various types of rock in each face. Drilling and blasting limits are geologically controlled if warranted, or large blasts embracing several rock types are shot and the resulting pile of broken rock is staked along shovel limits.

Jan 1, 1966