Search Documents

By J. M. Keane, C. K. Chase

Critical to successful dump and heap leaching of copper is an adequate evaluation of applicable parameters. This paper deals with methods to establish optimum conditions for dump and heap leaching copper so that commercial operations can proceed. Discussion is also offered of ore occurrences and preparations for dump or heap leaching.

Jan 1, 1988

By Q. Feng

Study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature and curing time, significantly affect the mechanical property of geopolymer matrix. Through optimization, an above 100 MPa compressive strength has been achieved with the geopolymerization products. Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength even after a one month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS and XRD are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method to apply fly ash as a high strength water-resistant precast construction material. INTRODUCTION Geopolymerization is a process of obtaining a polymeric structure from aluminosilicate by dissolving aluminosilicate sources in a strong alkali (NaOH) solution and condensation of free [SiO4] and [AlO4] tetrahedral units (Davidovits, 1985 and 1988; Duxson et al, 2005; Xu et al, 2000, 2002). After being cured at an elevated temperature for a specific time, the geopolymerization product shows a greatly increased compressive strength. Therefore, the product can be used as construction material such as bricks and road pavement. It provides a very promising method to apply aluminosilicate sources such as fly ash as a construction material for a sustainable development. Fly ash is a main industrial waste which needs to be carefully impounded because of its potential impact on environment. Many efforts have been tried to utilize fly ash as construction materials substituting Portland cement because of the following reasons. First, fly ash is a silica/alumina rich aluminosilicate source, which makes the specific material an ideal source for the geopolymerization process. Secondly, the particle size of fly ash is usually very small (< 50 microns) and it saves a lot of energy consumed during the production process of cement for grinding. Thirdly, fly ash is an ideal source for geopolymerization because it is reactive to alkali even at a mild temperature. In the past twenty years, many studies have been carried out on the geopolymerization of fly ash to a make construction material. However, there are some disadvantages associated with the conventional methods of treating fly ash (Palomo et al, 1999; Perera et al, 2007; Temuujin, et al, 2009; Hanjitsuwan et al, 2014). First, in most of the proposed geopolymerization methods, a salient amount of sodium silicate has to be added. It therefore makes it complex whether the achieved mechanical strength of geopolymerization products is due to a real geopolymerization process between fly ash and alkali or just largely the solidification of metal silicate in air at an elevated temperature. Secondly, the authors have noticed that when the geopolymerization product is soaked in water, the solution pH increases sharply and the products will lose its compressive strength gradually in water. Thirdly, the compressive strength of the geopolymerization product as reported is usually less than 50 MPa.

Jan 1, 2019

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By Ramon S. Pizarro, W. Joseph Schlitt

Introduction Trying to synthesize innovations occurring in gold processing is not simple. At present, this technology is exploding, brought about by the high price of gold. This price has compelled the mining industry, as a matter of survival, to produce gold. The frantic search for gold deposits continues, from glacial areas to tropical jungles. The search has been fruitful. New exploration techniques have helped to locate deposits. Some are amenable to conventional processing techniques. Others are in unusual settings that challenge the ingenuity of extractive metallurgists. Ore deposits containing traces of invisible gold, refractory mineralization, and impurities and deleterious materials that previously defied treatment are now being profitably processed. Metallurgists have developed various processing methods and equipment for gold ore treatment that reflect differences in ore characteristics, grade, mineralogy, reserves, topography, climate, and location. These processes can be categorized as: • For nonrefractory or readily leachable gold ores - vat leaching, heap leaching, and agitation leaching. • For ores containing free gold - gravity concentration methods, followed by mercury amalgamation, and • For refractory gold ores - flotation, roasting, pressure oxidation, followed by cyanidation leaching. In actual practice, a combination of these processes may be required. This is because gold mineralization, although usually simple, may be associated with other mineral species or with clays that make the ore difficult to treat. Furthermore, after the gold has been solubilized to form a cyanide complex, one of two important processes must be applied to recover the gold. These ore zinc cementation (Merrill-Crow process) and Carbon adsorption, desorption, and electrowinning. New techniques for leaching and recovery are also advancing. These will become the bases for the next generation of gold processing plants. Nonrefractory Gold Ores Nonrefractory ores with readily leachable gold are among the .easiest to treat. Even so, non-refractory ores from epithermal deposits are likely to contain too much clay. When these ores are damp, they may clog the screens and cone crushers. Depending on the type of process, scrubbing the crushed ore is very effective in overcoming clay problems. After dewatering, the slimes enter the cyanidation process and the thickener overflow is stripped of gold values and recycled. Semiautogenous (SAG) mills are also gaining popularity due to lower capital costs and ability to treat wet, sticky ores. If properly sized, the secondary crushing and screening plants, together with a secondary ball mill, can be eliminated. When the ore is of such a low grade that it can not support fine grinding, vat or heap &apos;teaching may be applicable. These systems are being actively applied in the US and elsewhere. Rapid construction and low capital costs are important features of these plants. Vat leaching is ideally suited for fast leaching ores and small tonnage deposits located in areas with harsh winters or wet tropical climates. For effective vat leaching, the ore is crushed to less than 25 mm (1 in.), agglomerated with lime or cement to control fines, and leached with sodium cyanide solution (upflow or downflow). The degree of size reduction is a tradeoff between increased costs of comminution and improved gold recovery from smaller particles. However, the size of material

Jan 11, 1984

By John D. Morgan

Introduction The US Bureau of Mines&apos; (USBM) world reserve/consumption ratios (Table 1) indicate that, if the world is relatively peaceful in the next two decades, there should be ample world supplies of minerals to permit rising standards of living for increasing world population. But it must be remembered that most mineral reserve estimates are conservative and that normal mining practice is to develop a ton of ore reserve for every ton mined. It should be noted that "reserve," as used in this paper follows the definition given in US Geological Survey (USGS) Circular 831, 1980; "that part of the reserve base which could be economically extracted or produced at the time of the determination." In addition to accurately determining the geologic parameters of mineral deposits, a judgment as to whether that deposit is a "reserve" per se involves consideration of many other factors. These factors were recognized nearly a century ago by a well-known mining engineer and later President, Herbert Hoover. In "Principles of Mining," 1909, Hoover wrote: "Unfortunately for the mining engineer, not only has he to weigh the amount of risk inherent in calculations involved in the mine itself, but also that due to fluctuations in the value of metals. If the ore is shipped to custom works, he has to contemplate also variations in freights and smelting charges ...In a free market, the law of supply and demand governs the values of metals as it does that of all other commodities. So far, except for tariff walls and smelting rings, there is a free market in the metals under discussion. The demand for metals varies with the unequal fluctuations of the industrial tides. The sea of commercial activity is subject to heavy storms, and the mine valuer is compelled to serve as weather prophet on this ocean of trouble. High prices, which are the result of industrial booms, bring about overproduction, and the collapse of these begets a shrinkage of demand, wherein consequently the tide of price turns back." Current supplies and use There have been ample supplies of most mineral materials to permit several-fold increases of world production of common major mineral based minerals (steel, aluminum, copper, and cement) over the past three decades. Motor vehicle production is a major consumer of mineral materials. However, in the last decade, down-sizing to facilitate improved fuel efficiency and reduce harmful emissions has reduced the weight of the average US-made automobile 15%, to 1.5 t (3200 lbs). Also in the US, there are 92 million dwelling units, or on average, fewer than three persons per dwelling unit. Construction is another major consumer of materials in the industrialized developed countries. It will also be a major consumer of materials worldwide as less developed nations seek to improve their infrastructures by adding roads, bridges, railroads, airfields, ports, and housing. Fortunately, a large number of traditional common materials, many of mineral origin and also many of agricultural origin, are readily available for construction. Traditional construction materials such as steel, aluminum, copper, and cement, are being replaced in many applications by engineered plastic and ceramic

Jan 4, 1986

By D. Burkhard, E. Herth

"Geologic structure and properties are the primary influences on ground control at San Juan Mine. Geotechnical properties of the coal seam and near seam strata, the presence of above seam sandstone paleochannels and water, are thought to be the leading contributors to ground control issues. It is the confluence of specific geologic conditions rather than isolated features that most often produce adverse conditions. Altering primary support installation and mining practices are done when unfavorable conditions appear during development. Installation of standing support is most often employed when adverse conditions develop at later dates. REGIONAL GEOLOGIC SETTING San Juan Mine is an underground coal mine located on the western flank of the San Juan Basin in northwest New Mexico. The San Juan Basin is contained within the south eastern region of the Colorado Plateau geographic province. The basin contains multiple coal bearing formations and is also a major producer of coalbed methane gas. San Juan Mine is stratigraphically located within the Fruitland Formation. From a prominent monocline marking the western boundary of the basin, the formation dips gently to the east towards the center of the basin. The primary driver for the deposition of coal bearing formations within the basin was the Cretaceous Inland Seaway. Multiple cycles of transgression and regression driven by sea level rise and tectonic subsidence deposited rock types from marine shale’s to terrestrial sandstones. The Sevier Mountains to the west of the seaway likely provided the sediment supply for the Fruitland Formation. During a major cycle of seaward regression, the Pictured Cliffs Sandstone Formation prograded over the marine Lewis Shale. The coal bearing Fruitland Formation followed, being deposited over the Pictured Cliffs. The Fruitland Formation contains numerous coal seams and is approximately 400 ft. thick at San Juan Mine. Fruitland Formation coal seams are numbered in order of superposition. San Juan mines the Fruitland number 8 seam. Dating has placed the age of the seam at approximately 73 to 75 million years [1]. LOCAL GEOLOGIC SETTING The Fruitland 8 coal seam dips approximately 1-3 degrees towards the E-NE. At San Juan Mine, the seam displays a mild plunging, synclinal structure, the axis roughly bisecting the mine from west to east. The number 8 seam consists of five coal benches and four volcanic ash band partings labeled sequentially based on superposition. The lowest portion of the seam is the 8-1 bench, the 8-2 through 8-5 benches following sequentially to the top of the minable seam. Ash band partings are labelled P1 through P4 from bottom to top respectively. The presence of distinctive partings and benches allows for seam definition and aids in identifying mining horizons."

Jan 1, 2016

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016

By H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a potential secondary resource because of the higher concentration of valuable platinum group metals (PGMs) as compared to the primary ores. Despite the well-developed commercially tenable technologies, further researches are being carried out to extract the PGMs with high efficiency. It is however, critical in this context to reuse not only the PGMs but also other metals contained in the spent auto-catalyst particularly that of the cordierite substrate such as aluminum, magnesium and cerium oxide (CeO2). This is important in view of the fact that no recycling process has ever stressed upon the recovery of cordierite substrate and CeO2 since the main target metals are mostly the PGMs. In this study, a new hydrometallurgical approach has been proposed in order to recover the PGMs as well as cerium oxide and materials from the cordierite substrate by using sodium hydroxide roasting followed by sulfuric acid dissolution. Under the optimal conditions for roasting at above 600°C, and weight ratio of sample to NaOH of 1:1 for 60 min, the cordierite was converted to the soluble phases. Dissolution of the roasting products using H2SO4 solution (1M) at 25°C for 60 min enriched the PGMs and Cerium oxide contents in the residue. Subsequently, PGMs in solution after dissolution can be cemented using Al and Cerium oxide in residue can be recovered by hot digestion using concentrated H2SO4.. INTRODUCTION Auto-catalyst can significantly control the gaseous emission of automobiles, and has been considered as a potential secondary source of Platinum group metals (PGMs) after being decommissioned from the vehicles. The PGMs demand is continuously increasing to comply with the growing vehicle population and the tightening of emission standards all over the world; meanwhile the natural resources of these metals is facing the threat of depletion. Therefore, it is crucial to progressively substitute with an alternate resource to supply PGMs other than that of the primary ores. Nowadays, vehicular transportations worldwide are totally installed with the auto-catalysts. However, they should be replaced after reaching their service life. If there is no recycling of such resources, huge amount of valuable metals will be wasted. The quantity of PGMs that can be recovered from the spent auto-catalyst depends on the size of car, which averages to 1-2 grams for small cars and 12-15 grams for the big truck; this is significantly higher than that of the primary ores containing 2-10 grams PGMs per ton. Consequently, the recovery of PGMs from spent auto-catalyst becomes extremely favorable as compared to the primary resources due to higher concentration of PGMs, with much lower and simpler processing steps, and lesser pollution."

Jan 1, 2018

By D. Kruse, M. Sanaei

"A three dimensional nonlinear finite element model was constructed to simulate and analyze the behavior of large diameter segmentally lined shafts when subjected to seismic waves. To reduce computation time, a less complex shell model was also constructed. Transient excitation was applied to the supported nodes of both models, at the base of the shaft, with a time-function representing the 1994 Northridge earthquake. The models are developed at the end of an original phased construction-stage analysis of the shaft. Displacements, forces and moments are monitored and compared during the analyses steps. During the initial 15 seconds of the earthquake, the top and bottom of the shaft show similar displacements. The maximum horizontal displacement within the shaft is approximately 3.5 inches in the solid model and the shell model results conform to this by a factor of 50%. Keywords: Segmentally Lined Shaft, Soil Structure Interaction, Seismic Analysis, Finite Element Modeling, Ground Modification INTRODUCTION TO SEGMENTALLY LINED SHAFTS Large diameter segmentally lined shafts (SLS) are underground systems, constructed sequentially using precast concrete segments to form a ring which provides both temporary earth support during excavation and permanent structural support. The segments are connected via alignment pins, bolts, packer material and other structural components that ensure the continuity of the SLS. In this analysis, the construction process uses a top-down sequence wherein each soil layer is excavated, damp-proofing is installed and concrete segments are assembled to form each ring. This process is repeated until design depths are achieved completing the shaft. It is known that cylindrical structures sustain lateral (earth) pressure mainly through the mechanism of hoop-stress. As Timoshenko’s ring theory goes, a cylinder shell structure is prone to buckling under external pressure [1]. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. However, in shafts with large diameter to wall thickness ratios, buckling could become a critical issue. In any given mode, as buckling occurs in a ring, some sections of the structure move inward while alternating sections protrude. Although the presence of the surrounding soil could mitigate the buckling by resisting the movement (Soil structure interaction) seismic loads can cause ground movements and lateral pressures, exceeding the capacity of the structure. It is therefore essential to design the load bearing capacities of the shaft to minimize the possibility of any catastrophic failure due to earthquakes. This study explores the structural response of the SLS when subjected to seismic loads."

Jan 1, 2016

By D. Craig Camp

Microtunneling has successfully completed both horizontal and vertical curves. This paper covers the historical development of curved microtunneling and a description of one microtunneling project. The completed microtunnel is used for electrical transmission in Japan. The crossing had several concerns including right of way, social disruption, obstructions, the cost of intermediate shafts, and political restrains. In order for this drive to meet all of the imposed restrictions, four horizontal curves and one vertical curve were planned and executed in accordance with the design. Iseki Poly-Tech of Tokyo, Japan designed and built the microtunneling machine to meet the project requirements. Curved microtunneling has been successfully used on fourteen projects in Japan. The reason for a curve has been that the project could not be rerouted, short straight drives could not be used to negotiate the curve, or the project’s social and environmental conditions required a curved tunnel. The following table (Table 1) includes summary information on 14 curved microtunnling projects that have been successfully completed in Japan. The first column is a reference number. Columns two through four include basic project information. The fifth column is the total project distance completed by microtunneling. The sixth column is the project’s microtunneling duration. The seventh column is the machine type and size. All of the machines listed are manufactured by Iseki Poly-Tech of Tokyo, Japan. The size is the internal concrete pipe diameter; all of the projects listed were completed with Japanese standard concrete pipe. The eighth column contains a general description of the soil. The soil type and blow counts are approximately equal to ASTM D 2487 standards. The ninth column lists the radius of the curve and the span distance or the distance microtunneled that included the curve. The radius of a vertical curve is denoted with a “VR”, a span with both a left and right hand curve is denoted with a “S”. Other significant first events are also noted in this column. The first curved microtunneling project was completed in 1982 using a conventional microtunneling machine with standard Japanese concrete pipe and a very long radius curve while maintaining grade for the gravity sewer. The second curved microtunneling project included multiple radii curves, all in the same direction, on a single drive. In 1989, on the fifth curved microtunneling project, a “S” curve was successfully negotiated. On the seventh curved microtunneling project, completed in1995, a tight radius curve was negotiated. In 1996, the eighth project included a vertical curve. The thirteenth curved microtunneling project, completed in 1997, was the first project to utilize a microtunneling machine specifically designed to negotiate curves. The fourteenth curved microtunneling project was the accumulation of all

Jan 1, 2001

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By David Whitehead

My qualification to speak on the globalization of the the mining industry comes from having worked in the industry in Europe, North and South America, Africa and Australasia in positions ranging from exploration geologist to chief executive. For about a third of my career I have lived and worked in the Southern Hemisphere. And for much of the rest of my career I have been involved in or responsible for activities in the Southern Hemisphere. This has given me the opportunity to experience globalization from the sharp end, as it were. This means speaking English with an Australian accent, Spanish with a Chilean accent, French with a West African accent and Dutch with an English accent. My topic is globalization, especially of the mining industry from a Southern Hemisphere perspective and specifically the experience and history of Gencor in that context. First, I will say a little about what globalization means to the southern part of the world: How and why the South differs from the North and how the challenge of globalization affects a south-based company differently than a northern one. I will also detail how Gencor has made significant progress in globalizing through the acquisition of mining assets from Shell. As Fig. 1 shows, I have divided up the world into northern and southern components, rather than hemispheres. The southern world comprises mainly countries that have emerged from the status of economic - if not political - colonies of nations such as England, Spain, Portugal, France, the Netherlands and, surprisingly, Italy and Germany. I have not considered the Indochinese and Arabian peninsulas in my southern world. The emergence of the. former is still in its early stages while the latter is clearly a part of the northern economic system. Large parts of Africa and South America are geometrically in the Northern Hemisphere but economically in the southern world. The reverse is the case for the IndoPersian peninsula. With the distinguished exception of Australia and South Africa, most of these countries nationalized their mining industries and mineral patrimony after attaining political independence. A major element of the globalization of the mining industry is related to the privatization of the mining industry in these countries and to the opening up of their min¬eral patrimony to non-national exploitation. The Southern Hemisphere is the watery part of the world. It is almost three quarters ocean as against a slight preponderance of land in the north. Economically, ocean areas have only a fraction of the productivity of land, except in a few oil-rich areas like the Gulf of Mexico and the North Sea. The consequence is that even on an economically level playing field we would expect the south to generate only about one third of the world&apos;s economic product.

Jan 1, 1997

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on overall grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: •Different lining profiles in rubber and steel. •Orebed magnetic lining. •Steel-cap rubber lining. Introduction Grinding mill liner life has been a subject of extensive studies. Performance of mill liners in terms of wear life and how it relates to lining material and profile is abundant in the literature. The most economical liner material and design has been selected based on "cents per ton milled". The evaluation of the effect of liner design on power and grinding media consumption which is a far more significant part of grinding costs, has been less comprehensive (Fig. 1). Lining materials Steel. The most commonly used lining material is steel, calculated on a volume basis. Steel linings have a long tradition and a number of alloys is being developed. The main families are: •High chromium white iron. •Cr and Ni white iron (NiHard). •High chromium martensitic steel. •High carbon Cr-Mo perlitic steel. •High carbon Cr-Mor martensitic steel. •Manganese austenitic steel. Steel linings can be successfully used in most applications. Rubber. Rubber linings were introduced 25-30 years ago and are today commonly accepted to be the most economical linings for secondary and regrind applications. Rubber linings offer long service life in these applications and generally [ ] outlast steel in wet applications, where corrosion is a factor on the steel. The cost relation between rubber and steel has changed dramatically over the years. In the past rubber was more expensive than steel, but today, the cost of rubber is close to half the cost of steel, calculated on a volume basis (Fig. 2). The present cost situation has made rubber linings an economical alternative in several primary grinding applications as well. The wear rate of rubber in primary applications is higher than the wear rate of steel, thus giving a shorter wear life. This can be compensated for by making the rubber lining thicker. The cost advantage of the rubber allows for this, but care must be taken not to jeopardize the grinding performance. Rubber, as a lining material, offers some distinct advantages over steel lining, such as: •Ease of installation and removal. •Safer to handle, less risk of injuries. •Faster replacement. •Reduces noise.

Jan 1, 1996

THE PENNSYLVANIA STATE UNIVERSITY, 101 MINERAL SCIENCES BUILDING UNIVERSITY PARK. PENNSYLVANIA 16803 To the Editor: With respect to the Fenvessy and Schwab article, I offer the following: As thorough as the study may be, it still has a glaring weakness. The presumption of constant supply in face of falling demand - their "low growth" case - is just wrong. It does not allow for the rapid migration, by transfer and change of major, from former high-demand programs, such as mining, to programs that have more recently obtained the cachet of job security. The figures that are shown for rapid growth in mining engineering enrollments in the period 1970-1981 are, no doubt, correct and reflect a rapid inmigration of students into mining. A similar out-migration, which began in 1982, from mining to other engineering and science disciplines is not factored into their study. Given 1983-84 enrollments, which can already be documented, it is clear that the low-growth case will, by 1985, be 50% or less of 1981. I wish students would pick their majors on the basis of their own individual abilities and interests rather than rushing lemming-like to programs that are reputed to have jobs. In the end, students will have better jobs and careers if their college majors match their talents and we, in the academic side of things, will have a livelier and more dedicated student. Lee W. Saperstein Professor and Chairman of Mining Engineering UNIVERSITY OF MISSOURI-ROLLA To the Editor: I write concerning the recent article on future demand for graduates in the mining industry. The article is, unfortunately, inaccurate because of the erroneous assumptions it makes in its basic premises. To cite but two of these, class sizes will not continue at their current level, but will, in fact, alter dramatically as a function of the perceived immediate job market rather than the future trend, so that enrollments are already below those predicted. Secondly, it is patently wrong to assume that everyone who gets a degree in the mining field will continue until retirement to work in that field. People who do not have a job in the industry will get work elsewhere and often do not come back. Others will later move to different areas. My major argument, however, deals with the underlying assumptions and methodology of the survey itself, with the concomitant challenge to the subsequent conclusions. It is no great secret that the technological world is undergoing a dramatic revolution. Computer use is rapidly spreading to the point where the microcomputer will be an integral part of every mine engineer&apos;s desk. Such a tool, which for optimal benefit must be operated by knowledgeable mining engineers, will make mining much more of a science than the current level. To remain competitive, mines will increasingly rely on higher level deci-

Jan 1, 1984

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By Majid Sadeghi, Ali Naghi Dehghan, Kaveh Ahangari, Seyed Mahdi Pourhashemi

"Instrumentation and monitoring of ground deformations in tunneling is a principal means for selecting and controlling the excavation and support methods among those foreseen in the design, for ensuring safety during tunnel construction (including personnel safety inside the tunnel and safety of structures located at ground surface) and, finally, for ensuring construction quality management. In this paper, the effect of Hakim Tunnel excavation on the behavior of the surrounding ground was investigated based on the geotechnical instrumentation. This tunnel with 1080 m length, 18 m width and 12.6 m height is being constructed using the SEM/NATM along the Hakim Highway in Tehran. The results which are obtained from recorded displacements by geodetic pins (on the tunnel wall and roof), extensometers and settlements pins (at the ground surface) demonstrate the tunnel stability during the various stages of excavation. However, it is concluded that the rate of excavation in different sequences could have a major role on stability of tunnel. In this case the surface and underground openings were monitored as well as needed for controlling the face probably collapse. INTRODUCTION Tunneling is increasingly being used world-wide to provide the infrastructure required for sustainable urban areas. The high demand for space and the disturbance of existing infrastructures by construction measures increasingly forces future infrastructure projects to be conducted underground. One of the important purposes of tunneling projects in urban area is not only to minimize displacements but also to control them during the construction (Pourhashemi et al., 2015). Normal method of tunnel stability analysis is not able to evaluate the real rock and soil mass behavior. Hence, instrumentation is a practical method to monitor displacements, to evaluate the stability of underground openings, and also to determine the rock and soil mass properties (Dehghan et al., 2012. Dehghan, 2013). Rocks and soils are materials with properties that can change instantly and significantly from one point to the next. Some complications may often happen due to uncertainties in the loads that the new facility must withstand during construction and operation. Instrumentation and monitoring provide quantitative information on actual behavior of ground and adjacent structures. A lot of deformation monitoring studies for determining and analyzing different kinds of engineering structures such as tunnels, bridges, high-rise buildings and dams are implemented. Considering the type of the structure, its environmental"

Jan 1, 2016

By Jan Visman, James W. Parkinson

GENERAL INTRODUCTION Sample collection, preparation and analysis are all steps in a single process designed to provide information about a much larger amount of material than the sample itself. For example, information about the ash content of a unit train load of coal may be derived from a single, relatively small sample of perhaps a few hundred pounds (liters) extracted from the entire shipment. These three steps can be thought of as links in a chain, allowing the simple analogy that the strength of the chain, or, in other words, the value of the information is only as strong as the weakest link. Sample collection, discussed in Part 1 of this chapter, is critical because analytical procedures can do no more than reveal the characteristics of the sample presented to the laboratory. If that sample does not properly represent the population to be characterized, neither will the analysis of that sample. Sample preparation is also a critical part of the chain. Any change in the nature of a sample between the time it is collected and the time it is analyzed will appear to reflect the nature of the population. For example, sample preparation procedures that allow air to partially dry the coal sample before reaching the laboratory will cause the sample analysis to indicate a lower moisture content than the sample originally had. Other changes can be more subtle. Second only to moisture loss, oxidation reactions generally cause the greatest problems. Oxidation of a coal sample can alter surface properties, changing flotation response. In extreme cases, combustion parameters, such as caking or agglomerating properties or mineral composition, such as pyrite content, can change. Water samples can also be altered by oxidation. For example, ferrous iron can oxidize to ferric iron, possibly changing water quality parameters such as pH. Sample analysis, the subject of Part 2 of this chapter, is the final link in the chain. Obviously, no laboratory procedure can correct for problems created by improper sample collection and preparation. At the same time, poor analytical techniques will create incorrect information about the total amount of coal from which the sample was extracted (the population) in the same manner as improper sample collection and preparation. The key to gaining correct information about the population is to view these three steps as parts of a single process. Following proper techniques through only one or two steps of the process will not produce accurate information.

Jan 1, 1991

By Kenneth L. Clifford

We have heard a lot during the recession about the mining industry now competing in a world market for sales of such commodities as copper, lead, zinc, molybdenum, iron ore, and phosphate. If the US mining industry is to survive, do we not have to reduce direct operating costs to a minimum? How significant is labor cost compared to consumables, electricity, fuel, maintenance, materials, and transportation? Ore grade is ultimately the dominant factor; but can we offset its dominance by improving productivity? Is the US mining industry perhaps only 25-30% as productive as it might be? What prevents the industry from being more productive? Can we retrofit older plants to be more productive or does it take a new plant with the largest equipment available for each unit operation? Present Productivity A copper industry study a few years ago covering 13 US copper concentrators ranging from about 10-45 kt/d (11,000-50,000 stpd) showed that productivity did not vary with capacity above 18 kt/d (20,000 stpd). Operating productivity varied significantly, however, from about 180-635 t/d (200-700 stpd) per operating hourly worker in most units, but one operation had 900 kt/d (1,000 stpd). Concentrators with more than 545 t/d (600 stpd) per hourly worker were in the 23 kt/d (25,000 stpd) or more category. Maintenance productivity covered about the same range, but most concentrators were in the 270¬635 t/d (300-700 stpd) per hourly maintenance worker. Again, one company stood well above others by exceeding 1 kt/d (1,100 stpd). Total hourly productivity ranged from 125-280 t/d (140-310 stpd) per hourly worker for most concentrators. The company with the most productive operation, however, was above 455 t/d (500 stpd). Salaried worker productivity for most operations was in the 725 t/d to 1.2 kt/d (800-1,300 stpd) per salaried worker range. The best operation was 2.2 kt/d (2,400 stpd). The end result is, of course, tons per day per total personnel. Most operations fell in the 110-220 t/d (120-240 stpd) range with the best operation at 400 t/d (440 stpd). This is the productivity definition that is most directly related to unit costs. Many of these operations have made some productivity progress

Jan 11, 1983

By John A. Lombardi

The solutions used in the heap biooxidative treatment of sulfidic refractory Au ores and concentrates generally load free mineral acid and metals and, in time, become bacteria activity inhibiting due to increased acid and/or metals concentrations. The metals­acid loaded, bacteria action inhibiting, solution must then be: (a) processed, prior to re-use, to reduce its metals and/or free acid mineral acid components to bacteria activity compatible levels; or (b) neutralized prior to discharge. The most common solution processing method to adjust acid-metals contents is liming to effect the precipitation of dissolved metals and neutralization of acid sufficient for solution discharge or re-use. The lime treated solution is high in suspended, colloidal precipitates and requires clarification before reuse. Most often the "bleedstream" of biooxidation solution that is lime treated is discharged and req­uisite volumes of fresh water added to the process inventory. Depending on the level of bacterial action in a heap and the acid consumption characteristics of the ore/concentrate being biooxi­dized, the bleedstream taken from the circulating, irrigation on­off, solution, can be large (e.g., 10%-20% and sometimes as much as 50% of the daily solution flow requires treatment-dis­charge). The lime charge for bleedstream treatment is commen­surately large and represents a major operating cost of the bioox­idation process. The patented HW Process Technologies (HWPT) Engineered Membrane Separation (EMS™) method is an alternative biooxi­dation bleedstream treatment method. EMS™ processing removes the multivalent base metals ions in an acid solution to a small volume EMS™ "concentrate" (typically 25% of the feed­stream volume). The EMS™ method coincidentally makes a "clean acid" EMS™ "permeate" (typically 75% of the feed­stream volume). In general, EMSTM processing enables 75% of the bleedstream volume to be recycled; allows up to 2/3 of the bleedstream acid to be recovered as a 10% solution; and delivers dissolved metals in a highly concentrated stream suited to a. metals recovery or b. reduced cost lime neutralization for a given metals precip­itation relative to full bleedstream neutralization (typically a 30% lime use savings). Implicit in the recovery of process water for re-use and reduced reagent addition requirement for metals precipitation is a significant reduction in wastewater-sludge dis­posal facility size.

Jan 1, 1998