Search Documents

By D. C. White

The Vulture Mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11,000 kg Au and 8,000 kg Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely disseminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence all dipping north about 35°. Early mining focused on the vein-hosted gold particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pitting of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry.

Jan 1, 1988

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

The only good news in the exploration sector in 1982-a year plagued by low metal prices and weak demand-was precious metals. Gold in particular remained in the forefront, as it has for at least the past three years. The reason for this is partially due to gold's seeming resilience to conventional supply side factors-such as new production-that normally influence many other metals. Also, with projected production costs of about $6.40-$9.65/g ($200¬$300/oz), modest deposits with average grades can offer an early return on capital investment and good profit potential. Keeping escalating capital costs for new mining ventures within reason has shifted gold exploration efforts in recent years. Many mining companies are seeking relatively low grade, modest tonnage, near-surface gold mineralization. This, of course, leads to lower development costs using open-pit mining methods. Recent refinements in the carbon-in-pulp recovery process also has enhanced the economics of such deposits. Slumping economic conditions certainly played a key role in shaping exploration activity last year. Nearly every major mineral-producing state recorded exploration slowdowns. In Alaska, for example, development expenditures approached the level of exploration spending for the first time in the state's history. This not only reflects major companies' decisions to move toward production but also the economic slowdown. The worldwide recession stopped Nevada's exploration and mining boom "dead in its tracks," said John Schilling, state geologist. The year was one of layoffs and closings for the state's mines and exploration offices, he reported. Similar trends were noted in most other states, especially in the West and Southwest. In the Pacific Northwest, however, exploration appeared to continue at a relatively good pace considering the metals market. In the mining geophysical community, recent advances in telecommunications and microprocessor technology are continuing to provide a positive impact. Many geophysicists have begun using satellite digital communication links to access computer systems from remote sites where using a microcomputer would be difficult. There were also major contributions made in exploration geochemistry last year. Highlights include progress in formulating mineral deposit models, geochemical exploration in glaciated and arid environments, and publication of many informative books. The following state-by-state summary and articles on geophysics and geochemistry provides a detailed view of exploration events throughout the US in 1982.

Jan 5, 1983

By P. Albert Carpenter, Wallace B. Howe, Michael N. Greeley, E. C. Bingler, Gilbert R. Eakins, Christy Bell, John Callahan, Gary B. Glass, T. J. Crabs

Although gold's market price dropped considerably from 1980's all time high, exploration for the precious metal remained a particularly bright spot last year, especially in the western US. For example, in Nevada-the nation's largest gold producer-further exploratory drilling at Louisiana Land & Explorations Co.'s deposit at Round Mountain and Newmont Mining Corp.'s find near Carlin resulted in sharp boosts in estimated reserves at both sites. Louisiana Land said its deposit is well on the way to being one of the largest gold reserves in the US. Based on further drilling, Newmont said its Gold Quarry property near Carlin could now produce 4.7-6.2 t/a (150,000-200,000 oz/ year). Reserves at Newmont's two properties near Carlin and a third property in southeast California are reportedly at least 218 t (7 million oz), up from the previously announced 128 t (4.1 million oz). Gold exploration activities were brisk in many other states, including a noticeable effort to explore and reopen dormant properties. Although the return on investments didn't appear as favorable last year as they did in 1980, the gold price was apparently sufficient to spur healthy exploration activity. Outside precious metals, market conditions, and subsequent exploration activity, appeared much more bleak. In the molybdenum market, for example, prices continued to slide, and Amax Inc. tightened its exploration budget. (Amax supplies 60% of the domestic market and 45% of the world demand for molybdenum.) The company spent 16% less on exploration during the first six months in 1981, compared to the same period in 1980. Copper and many other base metal producers appeared in similar straits throughout the year. Uranium exploration activities continued to suffer last year also due to depressed market conditions. Among others, Gulf Minerals Resources and Amoco Minerals Co. suspended uranium exploration activities in the West. Despite current unfavorable conditions, some companies continue uranium searches, confident that market conditions will rebound. On a brighter note, interest in exploring for some industrial and strategic minerals appeared on the upswing last year. Minerals used for oil and gas drilling, such as barite and special sands, were especially noteworthy. In geophysical activity, significant developments were achieved for electromagnetic techniques in both frequency-domain and time-domain systems. Geophysical logging activity declined due to decreased uranium exploration, and computer hardware continued to impact the way mining geophysical data are being acquired. Many presentations and papers were given last year to help exploration geochemists develop new techniques to locate concealed ore bodies. Among techniques described were statistical and computer modeling for enhancing anomalies over blind deposits.

Jan 5, 1982

By T. D. Maki

FMC Gold's Paradise Peak Mine, located 13 km (8 miles) south of Gabbs, Nevada, became operational in April of 1986. Shortly thereafter heap leach testwork began on sub mill grade ore. Presently, testwork continues in combination with production size heaps that account for approximately 6% of total gold production at Paradise Peak.

Jan 1, 1989

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By Vladimir Adamek

Due to the variability of subsidence characteristics across the U.S. coalfields, it was concluded that it would be practically impossible to develop a universal predictive model for mining-induced subsidence based on theoretical assumptions. Therefore, an effort was made to find a procedure to develop an empirical subsidence predictive model based on a sufficient Mount of field data from one mining area (in this case the Northern Appalachian Coal Region). It was also thought that this procedure, if successful, could be used as the template for developing predictive capabilities for other coalfields with different subsidence characteristics given a reasonable amount of field data. It has been found, in the Northern Appalachian Coal Region, that the variability of subsidence characteristics can be expressed by a polynomial equation developed through regression analysis of the variable subsidence coefficient and derived directly from the field data. In this study, field data were obtained from 11 Bureau longwall panel studies (16 half profiles) for static subsidence and 14 panels for dynamic subsidence. The effects of lithology, expressed in the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hythetically homogeneous overburden and existing ithological conditions. For each longwall panel, the characteristic of the variable subsidence coefficient was defined along individual static profiles. The definition of mean values with acceptable deviations is the substance of the predictive method. The same procedure was used to develop a predictive model for dynamic subsidence, since it war discovered that the rate of longwall face advance is not a necessary functional parameter. This paper presents the theory, development, and application of the static and dynamic subsidence prediction models.

Jan 1, 1986

By G. M. Bernard

An overview presentation of the fast-track start up of Cerro Colorado, a new copper heap leach project in Chile's Atacama' desert. A brief explanation 'of location of the property, exploration history, geol-ogy, reserves and development are presented. The overview includes mining, crushing, agglomeration, and the solvent extraction-electrowinning recovery process. Challenges and requirements specific to heap leach systems will be addressed and analyzed. A detailed description will be given of the mobile heap leach conveying and stacking systems used in the building of heaps for on-and off-pad operations.

Jan 1, 1995

By James A. Martin

In relating geology and mineral resources to the nongeologist engaged in planning and zoning, a major hurdle to overcome is often the concept of natural resources. Statements listing such "resources" generally include and often may he limited to such items as "open space", "buildings of historical value", "forest and wilderness areas", and "sites of natural beauty" but seldom mention minerals even where they are of significant economic importance to the area. Unfortunately, mention of mineral resources is often limited to statements calling for tight controls on mining to prevent "ravaging of the land". While, the concept of sequential use involving mining is sometimes acknowledged, it is frequently done in such a manner that this approach is discouraged. In the conflict for land between urban development, recreational open space and mineral extraction, far too often the mineral industry will be the loser. In Missouri, there have long been continuing requests for geologic and resource data for planning purposes from city and county government and from Federal agencies for inclusion in the various river basin studies and Soil Conservation Service projects. These reports vary in detail from concise statements of the geology of an area to rather lengthy reports on mineral and water resources, bed rock and engineering geology characteristics. In most cases, these reports as written were directed to a geologically-oriented reader. Our initial approach to presenting geologic data to the land-use planner was in the area of engineering geology with attempts to show the limitations that bedrock and soil conditions can place on development. The first formal reports, engineering geology studies of urban areas, were released by the Missouri Geological Survey in

Jan 1, 1976

By Jr. Wallace

This paper describes an analysis performed to determine the cool-down time of drifts in the prospective commercial nuclear waste repository in volcanic tuff at Yucca mountain, Nevada. Two emplacement methods are currently being considered at Yucca mountain. The reference configuration stores the high-level waste in short vertical boreholes, and the alternative configuration stores the waste in long horizontal bore-holes. After emplacement operations for each emplacement drift are complete, the drift will be closed off from continuous ventilation. Given time, the radioactive decay of high-level waste will increase the rock temperature around access and emplacement drifts. Air cooling may be required to re-enter these drifts. The paper discusses the analysis procedure and computer programs used to evaluate the time to cool a drift to acceptable environmental conditions 50 years after emplacement of high-level waste. Key assumptions to the analysis are presented. The results of the study show that cooling either vertical or horizontal configuration emplacement drifts is possible in a reason-able period of time.

Jan 1, 1988

Effective ground control in the gate entries, particularly in the tailgate travelways, is essential for safe longwall mining. Longwall pillars maintain gate entry stability and carry abutment loads. To answer the need for effective longwall pillar design, an empirical method called Analysis of Longwall Pillar Stability (ALPS) was proposed several years ago. Some recent research at the Bureau of Mines has focused on the refinement and verification of the ALPS method. ALPS was originally developed from field studies in which multiple stressmeters were installed in longwall pillars and monitored during mining. Several new field studies have now been incorporated into the ALPS data base. The field measurements have' been used to verify formulas for predicting abutment strength and pillar loads, and to develop an expression for the distribution of the abutment load.

Jan 1, 1989

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986

By Dean J. Acuff

An overview of new size reduction technology involving the use of two-mass natural frequency vibration applied to a totally enclosed elongated drum. Material moves with a drum-like rotary motion with exposure to constant, aggressive, high frequency agitation for faster reduction and enhanced product quality. A proven, patented design with few moving parts, a vibrating mill drum provides the desirable environmental benefits of a totally enclosed rotary drum but without the same interfacing difficulties. Natural frequency design has reduced energy demand which is met by low horsepower, self-contained, motorized drives to dramatically reduce the cost per ton of finished product.

Jan 1, 1993

By D. Hodouin

The improvement of mineral processing data using material balance computer programs is nowadays a current practice in many plants, engineering companies or research centers. It now becomes more obvious that such programs should integrate new features such as the preprocessing of data, the estimation of less accessible process variables and an in-depth interpretation of: the computed results. A few solutions to these new problems are already available. The feasibility of a mass balance computation for instance can be examined by analyzing the degree of redundancy of the measurements prior to any data adjustment. New variables such as chemical analyses in particle size intervals or liquid phase composition can be included in a set of measurements. Finally, a sensitivity analysis can be used to analyze the reliability of the results, to detect eventual outliers or to redesign a sampling scheme. Some illustrations of these new developments are presented.

Jan 1, 1989

By Donald R. East

For many years there has been increasing pressure on mining companies, not without some justification, to design tailings storage facilities which guarantee some degree of protection against process solutions entering local groundwater and surface water flows. A fairly straightforward approach to achieving this has been to design conventional water-retaining type structures, and this has often been reinforced by the need to store large volumes of process water and seasonal run-off within the tailings facility. The conventional design uses naturally occurring geological barriers and a conventional embankment with possibly a grout curtain, or artificial barriers around the entire facility, using either imported low permeability soils, admixtures, or synthetic liners. While these approaches may achieve the primary objective of minimizing seepage, various other factors should be considered. Firstly, by depositing the tailings slurry in a sub-aqueous manner, the tailings, especially if relatively fine grained, will settle to very low densities and little or no on-going consolidation may occur over the operating life of the mine, There have been many cases where measured pore pressures within the tailings mass equal the total overburden stress, i.e., no consolidation and no strength, many years after decommissioning.

Jan 1, 1998

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By D. W. H. Su

"This paper presents the results of a comprehensive study conducted by CONSOL Energy, Marcellus Shale Coalition, and Pennsylvania Coal Association to evaluate the effects of longwall-induced subsurface deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall abutment pillar can maintain mechanical integrity during and after mining operations. A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar were mined by. To evaluate the resulting coal protection casing profile and lateral displacement, three separate 60-arm caliper surveys were conducted. Prior to the longwall panels being mined by, a number of 3D finite element simulations were conducted to estimate subsidence at the surface, coal pillar pressure increases, the resulting coal protection casing profile and displacement, and the vertical and horizontal displacements in the four monitoring wells. Comparisons of the pre-mining 3D finite element simulation results and the surface/subsurface/underground instrumentation results show that the measured test well and IPI casing deformations and profiles are in reasonable agreement with those predicted by the 3D finite element models, and that the measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models, which serves to validate the 3D finite element models. Parametric studies employing the validated 3D finite element models demonstrate that larger coal protection casing thickness is expected to have little effect on the lateral deformation, although it may reduce the magnitude of casing plastic deformation, and under deeper cover (~1,100 feet), lateral casing deformation is expected to be smaller, although larger plastic casing deformation may be present near the seam level. Also, evaluation of various casing and cementing designs using the validated 3D models clearly indicates that, when all casings are grouted to the surface except the intermediate and production casings, the intermediate and production casings show little deformation and no plastic strain. This research represents a very important step and initiative to utilize the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the oil and gas industries"

Jan 1, 2017

Due to the relatively remote location of the St. Anthony Mine, the high cost of transportation and milling, plus the low grade nature of the deposit, the United Nuclear Corporation began investigating methods of mechanical upgrading approximately eighteen moths ago. This investigation culminated in the installation of Model 17 and Model 18 ore sorting machines. The machines are marketed in the United States and Canada by Ore Sorters of Canada (Ltd.). The installation of this advanced technology will enable United Nuclear Corporation to fully realize the residual potential of St. Anthony.

Jan 1, 1979