Search Documents

By F. Villanueva Araya

Compania Minera Disputada de las Condes (CMD), an Exxon Affiliate stewarded by Exxon Coal and Minerals Company, operates two' copper mines and concentrators in Chile. Pilot plant studies were initiated in 1984 using a 0.46 meter and a 0.91 meter diameter column for the cleaning of copper concentrate. This eventually resulted in the design and operation of a rectangular column with an area of 6.8 m2, increasing the final copper concentrate grade from about 30% to almost 32'1. Cu without any loss in copper recovery. Evaluation studies of a commercial bubble generator as against the previously used filter cloth air sparger are now in progress.

Jan 1, 1990

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By T. S. Golosinski

Use of contractors to excavate, load and haul mined material is widespread in Australia. It is also becoming a common practice in many other countries. The paper reviews current practices in Australian contract mining. Various types of contracts are reviewed, including partnering arrangements and alliancing between the contractor and the mine owner. Applicability of various types of contracts to specific mining situations is discussed, as is their impact on overall mine performance

Jan 1, 1998

By J. E. Lees

Advanced remote sensing can be a powerful new information tool to help private and public entities make better environmental and resource management decisions. However, some regulated entities are reluctant to develop or use this tool because of their concerns that it will lead to increased risks and costs of environmental legal liability. They fear that new ways of monitoring the environment will increase liability, undermine existing enforcement agreements, reopen compliance agreements, and generally provide a competitive disadvantage to early adopters by accelerating environmental cleanup costs. Others counter that the increased risks are marginal, and that several advantages outweigh these risks, including the opportunity to more effectively manage environmental operations, target and set priorities, measure and track management and compliance effectiveness, provide more defensible environmental assessments and baseline conditions, make and defend optimal siting decisions, and avoid or resolve environmental disputes. This paper offers strategic advice on ways regulated entities can enjoy the benefits of these powerful new information tools while mitigating down-side legal and compliance risks as much as possible.

Jan 1, 1999

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

By Thomas F. Evans

Niagara Mohawk, like other northern coal users, has long experienced increased costs during winter months as a consequence of handling frozen coal. These costs include operating labor, maintenance labor and materials, equipment rental, fuel for thawing, demurrage, carrying costs for excess coal inventory and substitution of higher cost electrical generation for lost production capacity. In the winter of 1978-79, limited trials of several coal freeze conditioning agents were made to determine whether these would provide a cost-effective means of reducing the problems of handling frozen coal. Since these trials were generally effective, the Coal Purchasing Department arranged that all rail coal received during the 1979-80 winter from early December to mid March would be treated at the mines during loading. Inasmuch as the treatment costs are themselves appreciable and our various coal suppliers made a variety of choices of chemical supplier and equipment for application, an attempt was made to evaluate the unloading performance of each train received at the two generating stations which use coal as an aid in the future optimization of the use of freeze conditioning agents. These stations also receive coal by truck but this coal is not treated because of the short hauling time. The C.R. Huntley Station in Tonawanda, NY has a capacity of 800MW and burns about 5000 tons of coal per day during the winter months. The coal is primarily from central and western Pennsylvania but one source in southern Kentucky is also used regularly. Most of the Pennsylvania coal is washed and the fines are thermally dried. The coal is delivered in unit trains made up of mixed cars of 60, 75, and 90 ton capacity. Time between loading and arrival at the station averaged five days and ranged from three to eleven during the 1979-80 winter season.

Jan 1, 1980

By R. M. Enick

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. The separation, conducted at ambient temperature and a pressure of about 1000 psi a, was based on the difference in wettability of precious metals and minerals. Contact angle results indicated that in the presence of water and liquid CO2, gold, platinum and silver had intermediate wettability. Minerals such as quartz and magnetite, however, were hydrophilic. Therefore fine gold particles. -325 mesh, that were mixed with water and liquid CO2 dispersed in the CO2 or agglomerated at the H2O-CO2 interface while the minerals tended to remain in the aqueous phase. Best results were obtained when these fine gold particles were liberated, were not agglomerated in slimes, were not adhering to minerals, and were not coated with minerals.

Jan 1, 1998

By T. Gonzales

Magma Metals Company operates an Outokumpu Flash Furnace, four Peirce-Smith Converters and two Anode Casting Wheels supported by six Anode Vessels. Process gasses from the Flash Furnace and Converters are treated in a two train/double contact sulfuric acid plant. Sulfur capture for the smelter is +98%. The new flash furnace was commissioned on July 7, 1988 and has processed over three million tons of sulfide concentrate without a major rebuild. Magma has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. This paper describes all the procedures, operation control parameters and operating philosophy that has allowed Magma to achieve superior performance.

Jan 1, 1992

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971

By Per-Martin Sandgren

LKAB's ores have specific mineralogical properties that make them especially suitable for the production of super-grade concentrates. Conditions are particularly good for this purpose at Malmberget, where a concentrate for high-purity sponge iron production has been produced for many years. Until 1978 the approximate assay was 71.2 % Fe and 0.45 % SiO2. Since then the assays have been improved by process modifications to approximately 71.5 % Fe and 0.20 % SiO2. Scope exists for still further improvement. In recent years the production of fractioned concentrates has been started. The material lies within the size range 74-125 µm and the approximate chemical analysis is 71.6 % Fe and 0.30 % SiO2. Other special products are under discussion. The Malmberget ores are also suitable for the production of high-purity direct reduction pellets with a SiO2 content below 1 %.

Jan 1, 1981

By Peter Maltby

A $20M pressure oxidation facility is under construction at the Nerco Con Mine, Yellowknife. Plant commissioning will start in the third quarter of 1992. Roasting of arsenical auriferous concentrates prior to 1970 left 45,000 tons each of highly toxic gold-bearing arsenic trioxide sludge and roaster calcine at the minesite. Safe disposal of these wastes has been a high priority. In 1983 an arsenic trioxide plant was built by the former owner to re-treat the sludge and to sell the product. Due to a poor market and high operating losses, the plant was closed by Nerco in 1989. Mine production in the future will revert increasingly to refractory ore as a replacement for free-milling ore which has been the mill feed since the roaster was shut down. With this fact in mind, Nerco management saw the potential of a proven process to recover the gold from a combined feedstock of refractory flotation concentrate, sludge, and calcine waste. A further requirement was the stabilization of all the arsenic as an insoluble ferric arsenate. By the end of 1989, after the completion of a literature search and a study of process economics, pressure oxidation was selected. Extensive bench and pilot plant work was completed in 1990 and early 1991 to develop the process parameters and to complete environmental testing of the autoclave products. Management approval for construction of a pressure oxidation facility was made in December 1990. Plant capacity is 96 tpd requiring a 40 tpd VSA oxygen plant on site. Detailed engineering began in March 1991. The pressure oxidation building was completed by the end of 1991. The autoclave arrived on site and was mounted on its foundation in December 1991.

Jan 1, 1992

By Martin C. Jones

INTRODUCTION This paper outlines the methods used to drill and pregrout prior to the excavation of five Mine Shafts in the Coal Measures of the Eastern United States. One example is the use of cement pregrouting of four 240 meter deep shafts and the second is the use of chemical pregrouting of a 360 meter deep shaft. These two examples will be compared and contrasted, both at the investigation stage of each project, and during the drilling and pregrouting itself, to illustrate the different approaches taken and how these affected the outcome, both technically and economically. INVESTIGATION FOR 240 METER SHAFTS In the case of the four 240 meter shafts, site investigation was carried out prior to bid, and information was made available by the Client in the form of a report. This report was based on pressure testing of NQ cored boreholes at each shaft site. Pressure testing was repeated two or more times, at each test setting, using 345 or 690 kPa of water pressure in accordance with the procedure outlined by the U. S. Bureau of Reclamation. Flow readings were taken every minute over a period of ten minutes. Maximum computed permeabilities, for the strata which accepted water under test for the shafts, carried between 1.0 x 10-6 m/s and 3.0 x 10-6 m/s, and total calculated seepages varied between 170' litres/minute to 3891 litres/minute. Although these figures did not indicate an excessive amount of seepage, the Client decided that pregrouting should be carried out, and chemical grouting was not discussed, even though the test permeabilities indicated the use of cement grout would be limited in this case.

Jan 1, 1979

In April 2012, work started on one of the most ambitious construction projects of Austria?s ÖBB-Infrastruktur AG ? the New Semmering Base Tunnel. Scheduled for completion in 2024, the 27.3 km (17 mile) tunnel through the Semmering range will cut the journey time on the south railway connecting Lower Austria and Styria. Before con-struction can begin at the entrance portal and tunnel bores, the work concentrates on the above ground sections with the clearance and excavation of the entrance ramp site. The slope is currently being excavated by the Baubeteiligungsge-sellschaft m.b.H. BBG-GRAZ. The cut face is shored up with shotcrete and permanent self-drilling anchors produced by Minova MAI, an economical bolting solution for softer rock formations. After completing the surface construction work, the twin-bore, single-track tunnel will be cut through the Semmering by conventional and continuous excavation beginning in 2015. Once completed, the New Semmering Base Tunnel will be one of the longest rail tunnels in Austria. It will act as a vital link on the route crossing Europe?s heartland from Northern Germany to Italy, which currently has to climb the steep Semmering pass between Gloggnitz and Mürzzuschlag on a historic mountain railway recognized as one of the UNESCO World Heritage sites. The old route imposes considerable limitations on heavy freight trans-port, and passenger trains have to slow down to a speed of around 50 kph (31 mph). The New Semmering Base Tunnel will bypass this bottleneck and cut 30 minutes off the journey time between Vienna and Graz. It represents a particular advantage for freight traffic, since the new route?s minimal incline of 8.4 percent removes all obstacles for even heavy freight trains.

Jan 1, 2013

By J. Stoll

In May 1998, Hanson Aggregates Midwest, as an outcome of mine planning, offered a 10-acre tract of land containing the famed fossil-bearing Silica formation, to the City of Sylvania, OH. in the form of a 99-year lease agreement. The Olander Park System, and Ohio code park operating within Sylvania Township, was then approved by Hanson and the City to manage and fund the park. All parties signed the lease in August of 1999. In November 2001, local residents voted to fund the park by a margin of 2 to 1. The park will consist of a shallow (approx. 20 ft.) former cement production quarry that is 700 ft. long by 300 ft. wide. Hanson’s motivation and vision for the park was fivefold: 1) the site was located away from long-term reserve access; 2) it would serve nicely as buffer property for the active quarry; 3) it had become an area of illegal dumping by locals in the past; 4) trespassing and safety issues would be limited by allowing supervised usage; and 5) the shallow outcropping contains the world famous, fossil-bearing Silica shale. Hanson will supply shale to the park perpetually via stripping activities in the process of uncovering quality construction aggregate limestone and dolomite reserves. Thousands of enthusiastic fossil hunters have already combed throughout the shale in their quest for “treasures”. The park’s master plan also features nature trails, picnic areas, a fossil-themed play area, amphitheater, visitor’s center and gift shop. Given the natural and people resources that Sylvania Fossil Park will have to offer, Hanson is confident that it will become the premier invertebrate fossil hunting site in the United States. It will also remain a solid community relations vehicle for years to come.

Jan 1, 2003

By R. S. Datta

Regulations on sulfur emissions have caused the electric utilities to evaluate various methods of meeting them. Low-sulfur, low-volatile coals can be burned alone or blended with high-volatile? coals. This option may be a cost-effective alternative to the installation of scrubbers on coal-fired combustion systems. In some blending applications, problems may be encountered because the low sulfur content and high calorific value of the low-volatile or other clean coal allow it to economically upgrade extremely poor quality coal. While this is done to meet specification purposes, actual boiler performance may be dominated by the poorer quality coal. Thus, the reputation of the low-volatile or other clean coal suffers. As a result of laboratory and full scale testing, conducted over the last five years, a model has been developed to evaluate the relative combustion characteristics of various coals and coal blends. A database for different coals has been gathered. This paper presents the model and shows how power plants and coal mine personnel can use it to evaluate their coals from different sources. It can be used to blend two or more coals from different sources so that thee blended coal has flame stability characteristics which are similar to those of the baseline coal.

Jan 1, 1991

By A. K. Clarke

In any treatment process that requires a coarse feed material to be reduced to a fine size by crushing and/or grinding it must be determined whether a wet or dry comminution system should be utilized. All factors must be evaluated in reaching the decision. Among these factors are: 1) Ecology and Plant Environment: Unfortunately in many instances the decision on wet or dry is based on prejudice resulting from an unnecessary fear of dust. The writers submit that this fear, although once justified, is no longer valid because technology and equipment is now available to collect dust to meet any standard. When dry grinding is used it is very often possible to discard a portion of the waste product in a dry state. This will decrease the size of the tailing pond required. As pollution control standards increase it becomes increasingly difficult to clean up water from tailing ponds. 2) Operating Costs: Steel wear is often five or more times greater in wet grinding than in dry grinding. This is mainly due to corrosion. The evaluation of the economics of dry grinding must of course include the air system and dust collection; similarly in a wet grinding plant related pumping and material handling costs should be included. Pumping costs are often overlooked. This assumes water is made to flow for nothing. Pumping can account for 20 percent of the power consumption in the grinding plant. Large scale comparative tests were conducted in a wet and dry commercial plant in 1970. The same ore was used for both tests. With all factors included in both plants the dry system showed lower horsepower per ton.

Jan 1, 1971

By E. E. Maurer

Kerr-McGee has operated the Ambrosia Lake uranium mill since startup in 1958. Tonnage milled per day has varied from 3500-7000 tons. The mill capacity is currently rated at 7000 tons per day. The process consists of two parallel circuits following crushing and sampling, \\lhich include open circuit rod mill grinding, sulfuric acid leach, cyclone classification, and counter-current washing circuits of sand classifiers and slime thickeners. Pregnant solution is clarified and polished by precoat pressure leaf filters prior to amine solvent extraction. Yellowcake is precipitated from the pregnant strip solution with ammonia, filtered and dried.

Jan 1, 1972