Search Documents

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Robert E. Wood

The temperature dependency of the low-density viscosity coefficients, ?°T, of helium and of nitrogen, 100° to 1,000° K, is correlated with empirical equations, and the temperature and composition dependencies of the low-density viscosity coefficients, ?°T, of helium-nitrogen mixtures are correlated with the Chapman-Enskog expressions by using the Lennard-Jones (6:12) potential function. The residual viscosity, ?T,P - ?°T (the difference between the viscosity of a compressed gas and the dilute gas at a given temperature), was found to be a function of the thermal pressure coefficient, (?P/?T)V, and two parameters, a and 1, which are characteristic of gas composition. The equation ?T, P = ?°T + a [(?P/?T)V]ß represented 1,340 higher pressure experimental viscosity values with a mean absolute deviation of 0.86 percent, and this equation was used to compute viscosities of the gaseous helium-nitrogen system for a range of temperatures and pressures including those encountered in Bureau of Mines helium purification processes and in a crude-helium conservation gas reservoir. Tabular viscosities for helium, nitrogen, and 13 helium-nitrogen mixtures are presented for 110 temperatures, 133° to 740' K, and 49 pressures in the range 1 to 240 atmospheres. The accuracy of the tabulated viscosities varies because correlation parameters were obtained from experimental data of unequal reliability. It is estimated that uncertainties in the computed viscosity values are ±5 percent for the region 325° to 740° K, ±2 percent for the region 183° to 325° K, and ±5 percent for temperatures below 183° K. The latter uncertainty may rise to y10 percent as critical conditions are approached.

Jan 1, 1970

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide alumina production capacity by plant and country. The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1993. Capacity data represent announced installed and planned capacities and do not necessarily reflect a Bureau of Mines judgment of actual plant operating levels or timing of planned expansions, The year-end capacity is the ?nameplate" capacity or estimated production capacity, whichever is larger.

Jan 1, 1993

By Peter L. Swanson

This investigation, which began 90 minutes after the February 3, 1995, seismic event, has benefitted from the assistance of a large number of individuals. These individuals provided information, data, analysis, brainstorming opportunities, field equipment, assistance with communication, conducted rock mechanics tests, and provided insight into mining in the southwestern Wyoming trona district. They include Rich Hodgson, Ron Hughes, Larry Refsdal. Mike Weller, John Kolesar, Joe Vendetti, and Rick Casey (Solvay Minerals), Dave Delling (Solvay consultant - former Solvay President), Karl Zipf (formerly with USBM, now with MSHA), Bob Friend, Bob Ferriter, Dave Ropchan, Jerry Davidson (MSHA Tech Support), Don Stauffenberg, Ben Hohler (Wyoming State Mine Inspector's office), Bruce Presgrave (USGS/NEIC), Chris Wood, Dan O'Connell (Bureau of Reclamation), Sue Nava, Jim Pechmann (University of Utah), John Norgord and members of FMC's mine rescue team (FMC Corp.), Bill Walter (Lawrence Livermore National Laboratory), Ron Gerlick, Kevin Wood, and Mike Harmel (USBM rock mechanics lab), Jim Case (Wyoming State Geological Survey), and Solvay consultants. In addition, many individuals helped us gather information on other recent large mining-related seismic events in Germany, Russia, and Australia. and other parts of the United States. These individuals include Wolfgang Minkley (IfG Institut fur Gebirgsmechanik, Leipzig), Arnfinn Prugger (Potash Corp. of Saskatchewan), Hartmut Spetzler (University of Colorado/ University of Bayreuth), Sergei Stanchits (Ioffe Poly-technical Institute, St. Petersburg), Rocky Thompson (Cyprus-Amax) and numerous seismologists throughout the Internet.

Jan 1, 2011

By J. Douglas Causey

In 1986 and 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 73,010 acres of the 76,480-acre Lower Owyhee Canyon Wilderness Study Area (OR-003-110) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 8 miles north of Rome. There are approximately 7.7 million tons of subeconomic zeolite (heulandite and/or clinoptilolite) resources with ammonia ion exchange capacities as high as 1.75 milliequivalents per gram in the Chalk Basin-Lambert Rocks area. The bed is 25 ft thick with less than 100 feet of overburden. This resource probably will not be mined in the foreseeable future.

Jan 1, 1989

By E. E. Maust

The literature on the activation of sphalerite for flotation by short¬chain xanthates leaves unanswered the question of whether a compact surface film of activator sulfide is necessary or merely sufficient for high flotation recoveries. Studies by Guarnaschelli and Plaksin indicate that xanthate adsorption and flotation of sphalerite are increased with increasing hole/ electron ratio. These results, and the known acceptorlike behavior of many heavy-metal impurities in zinc sulfide, suggest that activation may result from a traditional semiconductor doping effect at the surface. Using the theory of chemisorption states on ionic crystals as developed by Levine and Mark, the Bureau of Mines has carried out A calculation to estimate the surface-state energies of various metals when they are substituted at zinc sites on (110) sphalerite surfaces. Based on a simple Madelung-Born treatment of ionic solids, the calculation indicates that many of the metals known to activate sphalerite for subsequent flotation have lower surface-state energies than nonactivators. The results of these calculations are discussed from the standpoint of consistency with the proposed activation mechanism and observed flotation results. The satisfactory agreement obtained is taken to be support for the proposed mechanism, and further elaboration of a surface-doping model is attempted.

Jan 1, 1976

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 per-cent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Delta summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By J. P. Capp

The Federal Bureau of Mines and the Alabama Power Company conducted an experiment in underground gasification of coal at Gorgas, Ala. involving the use of hydraulic fracturing to increase the air acceptance of a coalbed for the introduction of combustion air and removal of product gases. Air acceptance is defined as the flow rate of air which can be injected into the coalbed at 65 p.s.i.g. This was the second time the hydraulic-fracturing technique was used at Gorgas. Sand suspended in a heavy oil served as the fracturing fluid in the first experiment; in the second the sand was two to six times larger and was suspended in a water-starch gel. In addition to providing further tests of the underground-gasification process, the purpose of the second experiment was to determine the effects of the larger sand and greater volumes of a water-base fluid on (1) the extent of the fractured area, (2) the air acceptance of the coal, and (3) the rate at which a gasification path could be carbonized (linked) through the coal, and to compare these results with those of the first experiment. The coal was fractured by injecting 11,000 lb. of sand and 33,580 gal. of water and water-gel at 200 to 600 g.p.m. and 900 to 1,000 p.s.i. The fluid fractured the coal and the sand served as a propping agent to hold the cracks and crevices open. Pressures during the fracturing operation at test boreholes indicated that the fracturing fluid extended only about 150 ft. from borehole H, the point of application of the fracture. Injection of air revealed that the air acceptance of the coalbed within this e t was materially increased. On the other hand, increased air acceptance also was noted at boreholes up to 280 ft. from borehole H and at the electrolinking area 300 to 400 ft. away, indicating that the fracture effects extended considerably farther than was evident from observation. Similar effects were noted at approximately the same distances after the first hydraulic fracture.

Jan 1, 1961

By G. G. Campbell

The Bureau of Mines initiated a field test of underground coal gasitication to investigate the technologic feasibility of gasifying a subbituminous coal. The test site is near the town of Hanna, Wyo., about 70 miles northwest of Laramie. Preliminary results of the experiment are described. The coal was ignited in the central well of a 16-well pattern. Both forward and reverse combustion techniques were attempted to prepare a path of sufficient permeability to permit the high air injection rat s necessary for gasification. Gasification between linked wellbores was sustained for periods as long as 3 months. Hydrogen-rich gas having a heating value of 100 to 150 Btu/scf was produced.

Jan 1, 1974

By Kenneth L. Cashdollar

The Mine Safety and Health Administration (MSHA) and the West Virginia Office of Miners? Health, Safety, and Training (WVOMHS&T) investigated the explosion at the Sago Mine in West Virginia, which occurred on January 2, 2006, and resulted in 12 fatalities. As part of the investigation, the agencies requested that the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory evaluate the effects of explosions on specific mine ventilation seals and other structures and objects at its Lake Lynn Experimental Mine (LLEM). The results of the LLEM study would assist MSHA and WVOMHS&T in a more thorough understanding of the various questions that arose during their investigations of the explosion. Six large-scale explosion tests were conducted in the LLEM from April to October 2006. The protocols for these tests, and in particular the procedures for constructing various Omega block seals, were developed mainly by MSHA and WVOMHS&T. NIOSH developed the experimental procedures at the LLEM that would provide the required range of explosion pressures against the seals. Three 40-in-thick seal designs using Omega 384 low-density block were constructed in the LLEM and exposed to various explosion pressures. These seal designs are referred to in this report as the ?2001 design,? the ?hybrid design,? and the ?Sago design.? The 2001-design Omega block seal (80 in high) located in crosscut 2 of the LLEM survived all six explosions, with pressure loadings up to 51 psi. The 2001-design Omega block seal (88 in high) in C-drift was destroyed during Test 2, which subjected the seal to a head-on explosion that resulted in a pressure loading of 51 psi. The height difference between the two seals and the orientation of each seal to the explosion were contributing factors. The higher seal would be weaker for the same seal thickness. The hybrid Omega block seal in crosscut 3 survived an explosion at a pressure loading of 25 psi and failed during another explosion at a pressure loading of 39 psi at the seal. Based on these tests, it seems that the hybrid seal design is weaker than the 2001 seal design. The Sago Omega block seals were constructed in crosscut 3 and C-drift before Test 3. The crosscut 3 seal survived a pressure loading of 18 psi and was destroyed during an explosion at a pressure loading of 35 psi at the seal. The C-drift seal survived a head-on explosion that resulted in a pressure loading of 21 psi and was destroyed during an explosion with a pressure loading of 57 psi at the seal. Based on these LLEM tests, it seems that the Sago seal design is weaker than the 2001 seal design, yet it still complied with the requirements of 30 CFR 75.335(a)(2) that were in effect at the time of the mine disaster. During these LLEM explosion tests, the distance of seal debris travel was also measured. In Test 5, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 57 psi, and the seal debris was thrown over 500 ft. In Test 6, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 93 psi, and the Omega block debris was thrown over 900 ft. During these tests, the explosion pressure effects on other structures and objects were also documented. Unless otherwise specified, all of the pressure data listed in this report represent the highest recorded smoothed (averaged over 10 ms) explosion pressure loadings. The information in this report was used by MSHA and WVOMHS&T as supporting data in their analyses and investigative reports of the Sago Mine explosion.

Sep 1, 2009

By Oliver Bowles

"Score of the Bureau's Investigations.There has been outlined in a previous report* the results obtained regarding the adaptability of pulverized waste slate as a filler in road asphalt mixtures. As pointed out in that report the percentage of waste at slate quarries is very high, and the Bureau of Mines has undertaken the problem of discovering new and enlarged outlets for the waste material.Many products such as paper, rubber, road asphalt, floor coverings, paints, etc., require as one of their important constituents a considerable percentage of finely pulverized inert mineral matter to give ""body"", to obtain the desired consistency, or to supply the necessary wearing or other qualities demanded. Such materials are known as ""fillers"". The possibility that slate flour might be used as a filler with advantage in several products other than road asphalt led the Bureau to undertake further investigation.The Importance of Discovering Advantageous UsesIt has been found that in some products slate may be substituted for materials now in use without any marked effect on the quality of the products. A wider use of slate in such products could result only from a definite price advantage as compared with other fillers. Mile it is probable that waste slate may be placed on the market at prices which will encourage its wider use, it is evident that a waste slate utilization industry can never attain sufficient magnitude to definitely assist the slate producers unless it is demonstrated that some definite advantage in quality may be gained when slate is substituted for fillers now in use. The main purpose kept in view throughout the inquiry has been, therefore, to find advantageous uses for waste slate in order that both producer and consumer may be benefited."

Sep 1, 1921

By Paul Zinner

An exhaustive program of geologic studies and mapping has been conducted by the Geological Survey in the Iron River district of Michigan since May 1943. Means of contributing to the success of these studies were sought by the Bureau of Mines, and eventually a program involving geophysical studies and core-drilling was undertaken in the area. All of the work was done either to develop data that would contribute directly to geologic studies or to investigate geophysical methods that might be used as a primary means for the discovery of minable iron ore.

Jan 1, 1949

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By Patrick D. Plumb

The Bureau of Mines (BOM) has begun a project to increase the understanding of the relationships between ecosystem health and its functions, and minerals development. The BOM, Juneau Branch, Alaska Field Operations Center, is providing support for ecosystem based land-management decision-making and the development of ecosystem based regulations by documenting the effects of mining on ecosystems and demonstrating the tools used to assess and analyze those effects. This is done by reviewing the data available on ecosystems and the environment at a mining site, the Greens Creek Mine near Juneau, Alaska, and applying available Geographic Information System modeling tools to assess the impacts of the mine on components of the pristine ecosystem. Habitat Capability Models for wildlife indicator species are used in this examination. Wildlife indicator species are used as indicators of ecosystem health by the U.S. Forest Service and the Alaska Department of Fish and Game, who developed these models for southeast Alaska. Analysis techniques from the U.S. Fish and Wildlife Service's Habitat Evaluation Procedures (HEP) are also used in this report. By applying available models and analytical techniques to the Greens Creek area, the benefits gained through mitigation of potential impacts become apparent. These or similar techniques are useful for cost/benefit analysis of mitigation alternatives. Also apparent from this analysis is that the degree to which potential impacts are observable will depend upon the ecosystem scale considered. This demonstrates the importance of defining the ecosystem and scale before performing impact and cost/benefit analysis. The watershed scale is found to be useful for assessing impacts to ecosystem components at the Greens Creek Mine. Much progress remains to be made in the modeling and prediction of impacts to ecosystems from mining activity.

Jan 1, 1994

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

By Judith L. Bolis

The Bureau of Mines estimated the potential availability of iron ore from 129 domestic and foreign mines and deposits in 25 market economy countries. The availability of four products on a total and regional basis was determined from demonstrated resources of 75.3 billion It. From the resources evaluated there are a total of 18.6 billion It of sinter fines, 4.9 billion It of lump ore, 14.7 billion It of pellets, and 820 MMlt of pellet feed potentially available at a 15-pct DCFROR, f.o.b. port. On a regional basis, at or below a total cost of $0.26 per iron unit there are 1.7 billion It, 2.8 billion It, and 186 MMlt of sinter fines potentially available from Brazil, Australia, and Africa, respectively. There are 825 MMlt of lump ore from Brazil and 1.4 billion It from Australia potentially available at or below a total cost of $0.24 per iron unit. There are 2.1 billion It of pellets potentially available from the United States at or below a total cost of $0.80 per iron unit, while 442 MMlt are potentially available in Brazil at or below $0.38 per iron unit. South America has 208 MMlt of pellet feed potentially available at or below a total cost of $0.28 per iron unit. While the resources of iron ore are more than adequate to satisfy demand, the future of the iron ore industry is very dependent upon changes in the world economy, and on the domestic scene, changes in the domestic steel industry and steel imports.

Jan 1, 1987

By Gary A. Kingston

Chromium resources in the United States are estimated at 1.8 million tons of recoverable chromium contained in 22.5 million tons of chromite-bearing material. Additional resource is presumed existent in large, but as yet undetermined, quantities of material containing less than 10 percent Cr203. No domestic resources are being mined presently (1969). Excluding transportation charges to domestic consuming areas, the total 1.8 million tons of chromim is estimated to be available, in ore or concentrate, at costs up to $0.64 per pound; 63 percent of the total is available under $0.11 per pound; and 38 percent under $0.08 per pound. It is judged that transportation from the resource areas to the existing market centers would add nearly $0.05 to the cost of a pound of chromium contained in ore or concentrate. Technically effective beneficiation methods have been developed for much of the known domestic resource, and further development might reduce costs of processing these materials. However, at present, domestic chromium resources are noncompetitive with foreign sources.

Jan 1, 1970

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977