Search Documents

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By H. Oterdoom, S. Pilger, T. P. Bui, J. Rotarius

"Most FeNi furnaces used to rely on post-combustion and off-gas cooling inside the furnace to eliminate the produced CO gas, and control the off gas temperature. As furnace load, capacity, and thus gas volumes increased over the years, this led to increased instabilities that can cause problems in controlling the operation. Some of the large capacity furnaces nowadays work with partial or full combustion outside the furnace, more similar to the steel industry. Forced combustion with or without enriched air and other additions can support in controlling post-combustion, stabilizing and even reducing off gas amounts, and affecting composition. This paper presents some of the possibilities and advantages of having a specially designed post-combustion system for the FeNi laterite industry, but that could also be applied to other processes as well.Large Scale Furnaces In the FeNi industry, the Rotary Kiln Electric Furnace (RKEF) process is still going strong in spite of continuous hope that hydrometallurgical processes will one day make the RKEF plant obsolete. Within the pyrometallurgical plants there is a continuous trend for larger scale furnaces. The development for a number of furnaces that were started before 1985 and increased capacity by “natural growth” is given in Figure 1. Natural growth refers to the development of the plants that after having mastered a certain level of operation, were ready for a higher load that could be installed either with a new furnace on the same site, or during a revamp. The advantages of natural growth are numerous, for example: •,Deep knowledge of the ore and its’ behavior, no need for testing, and little risk of surprises. •,Mining, laboratory, equipment, etc. is all proven technology for the conditions on site. •,Starting a furnace with increased capacity is a re-start, not a green-field commissioning. •,Typically, when increasing the production capacity of an existing plant, not the entire plant is commissioned for the first time, but only a part. In the FeNi laterite industry for example, the kilns may already have had the capacity to provide enough material."

Jan 1, 2017

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By J. M. Bowen, P. Wemyss

"Gold losses to natural carbonaceous matter during cyanide leaching have been investigated for over a century. The variation in the severity of the problem from one ore to another has led to a range of different processes being implemented at different mine sites. Most commercial options utilise one or more of the following processes: roasting, carbon pre-flotation, organic blinding, CIL, chlorine passivation, pressure oxidation, biological passivation, elevated temperature CIL, RIL and thiosulfate. This paper provides a background to identify the most appropriate process or combination of processes for a particular ore. It also presents information on how these processes may be implemented, drawing on information in the literature and from current or recent applications at operations such as the following: Stawell, Kumtor, Penjom, Twin Creeks, Macraes Flat, Kittilä, Fosterville, Inata, Carlin, Goldstrike, and Jerritt Canyon. Various process options have been dismissed, or deemed unsuccessful due to limited knowledge available on the strengths and weaknesses of the different options and their implementation. The authors have collectively been involved in flowsheet development and project implementation in four commercial plants that have treated preg-robbing ores.INTRODUCTION Cyanide processing has been the mainstay of gold recovery for well over a century. It is generally a very effective process with over 90% recovery on free milling ores, but complex and refractory ores may only give 0–50% recovery with conventional processing (La Brooy et al., 1994). People have written about gold losses to natural carbonaceous matter during cyanidation for over a century e.g. Feldtmann, (1915). The earliest reports related to African operations, but the issue has since been reported in Canada, North and South America, Australia, Russia and China. The phenomenon is usually referred to as ‘preg-robbing’ dating from the times before the use of granular activated carbon for gold recovery, when gold was lost from the pregnant solution before it could be separated from the leach solids and recovered by cementation. Many excellent reviews have been published e.g. Dunn et al. (2013), summarising the options considered and where they have been applied commercially."

Jan 1, 2017

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By G G. Suffel

T HESE remarks on the occurrence of strata-bound massive sulphide deposits are submitted be-cause the writer recently visited the principal Cyprus deposits (in January, 1965) and has also a back-ground of many years spent largely in detailed observation and map-ping of the Horne and Amulet ore-bodies, now largely inaccessible. They are particularly related to the Symposium papers (September Bulletin) by Hutchinson and by Roscoe. Some comments are offered on the cupriferous pyrite deposits of Cyprus. As the writer is currently reviewing the published literature on the related deposits in Turkey, a brief account of some characteristic Anatolian sulphide occurrences is given. The discussion is closed with some thoughts on the relationship between these Mediterranean sulphide deposits and those of northwestern Quebec and the Superior province in general. The geology of Cyprus, as it relates to the sulphide deposits, is well summarized by Hutchinson (1965). After visiting Mavrovouni, Skouriotissa and Limni and after much thought on the possible ge-nesis of these ores, it seems quite logical to me that he is right. They are indeed closely related to late-stage submarine volcanism.

Jan 1, 1965

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

By V. N. Mackiw, H. Veltman

"A process is described which permits the separate recovery of lead and zinc from complex low-grade sulphide concentrates such as are produced from the New Brunswick type of disseminated pyrite ores. This process calls for the preparation of a lead-zinc bulk concentrate from the original ore by flotation. The bulk concentrate is then oxidized under pressure in autoclaves in aqueous sulphuric acid solution, such as return electrolyte from zinc electrolysis. This yields a zinc sulphate solution and a residue containing lead sulphate, unaltered pyrite and elemental sulphur generated during the oxidation. After the oxidation, the leach slurry is briefly heated to above the melting point of elemental sulphur and then cooled. Thus, pellets containing pyrite and elemental sulphur are formed, and they are separated from the lead sulphate by screening and/or flotation. Laboratory tests have shown that about 95 per cent of the zinc and lead can be separately recovered from complex bulk concentrates. Process possibilities are discussed."

Jan 1, 1967

By Richard J. Haslinger, C. Mark Rebagliati, James L. Oliver

Abstract - Exploration at the Specogna gold deposit has identified a geological resource of 65.0 Mt grading 1.63 g/t Au, which equates to 3 million ounces of contained gold. This resource is hosted in a low-sulfidation epithermal deposit of Miocene age that is localized along the northwesterlytrending Sandspit fault. The fault has juxtaposed Late Cretaceous mudstone of the Haida Formation to the west, with Late Tertiary coarse clastic sediments and lesser andesitic volcanic rocks of the Skonun Formation to the east. A plagioclase porphyritic dacite dike intrudes the Haida mudstone and Skonun sediments along the fault. Gold mineralization, in hydrothermal breccias, veins and stockworks developed mainly in Skonun sediments and dacite. These are formed in an 800 m long zone that roughly parallels the Sandspit fault. The gold zone is funnel-shaped in cross-section, approximately 300 m wide at surface, 220 m above sea level, and narrows to approximately 50 m, at sea level. The deposit lies within an elongate zone of moderate to intense hydrothermal alteration that, at surface, extends over a known area of approximately 2 km2. Its western extent is bounded by the Sandspit fault. There is an asymmetric alteration zonation, with a core of silicic-potassic (adularia) and smectite-illite clay alteration that is bounded to the east by argillic alteration. Similar zoning defined by the distribution of metals reflects the position of the main feeder conduit. Mineralization of altered wallrock is dominated by 1% to 4% auriferous pyrite and marcasite. Gold and silver occur as electrum; individual silver minerals have not been identified. Other sulfides are rare, and are identified only microscopically. The mineral suite is typical of low-sulfidation epithermal systems. Gold occurs in early, multi-phase, variably bladed and banded quartz veins and breccias, which are cut by barren, single phase, drusy quartz veins.

Jan 1, 1998

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By W. J. Mcgaughey, M. A. Vallée

"Abstract -The application of geophysical technology to resource delineation aims to improve the quality of resource/reserve estimates by integrating high-resolution survey methods, geophysical modeling and inversion with three-dimensional representations of geological and mineral deposit data. The use of geophysics can cost-effectively improve a geological interpretation based only on geological and sampling data. Success depends upon the ability to use geological visualization and modeling software, first to develop a three-dimensional geological model and then to modify it interactively by integrating geophysical data with the geological and sampling data.The high resolution required for mineral delineation geophysics results in a focus on borehole seismic and high-frequency electromagnetic methods. Borehole wireline logging is used to develop an understanding of the relationship between physical properties and geological description. Data from core samples and borehole wireline logs allow the construction of a three-dimensional physical property distribution, consistent with the existing geological interpretation. The three-dimensional physical property distribution is used for both geophysical forward modeling (to compare to field data) and as a starting model in iterative inversions.Advanced visualization techniques allow the simultaneous viewing of the three-dimensional physical property model, the geological information and data from which it is derived, and the geological interpretation and the geophysical results. Geophysical results may be simulated responses from a forward model or the output from a numerical inversion in the form of an updated physical property distribution. Iterative refinement of the geological interpretation is required to ensure consistency with the geological and geophysical data. The key to success with this approach is that all relevant geological, geophysical, and rock property data reside in a common, visual model of the earth.Examples from massive sulfide deposits illustrate the benefits obtained by the integration of geophysical and geological data."

Jan 1, 1998

By M. B. Dusseault, A. Pirayehgar

"There is concern that hydraulic fracturing (HF) near an existing critically stressed fault could trigger slip and generate a seismic event of significance. To this end, a mathematical discontinuum model representing a naturally fractured rock (NFR) mass containing a fault is created, and fault slip response to fluid injection is studied. UDECTM is used as a Discrete Element Method (DEM) approach to define the seismic moment, and also to assess the influence of injection and slip on further shear slip propagation. In most of the simulations, slip and dilation take place along a number of oriented fracture surfaces, so it is reasonable to assume that in a real case, microseimic emissions would accompany each slip “event”. The moment magnitude scale (Mw) is used to measure the size of the microseismic event in terms of the energy released. Seismic moment is a measure of the total energy (work) released during a seismic event and is used to measure its size. From another aspect, the injection energy is calculated as the total energy required for achieving the hydraulic fracturing; this is viewed as energy to open fractures against the ambient stress field and much of it is potential stored energy that can be released and create discontinuities (work of fracture), deformations (W=F·d), heat and radiated seismic energy. A small amount of the total released energy is transformed to radiated seismic energy and another small amount results in tensile fractures. Fracture energy is used to calculate the work required to create fracture surfaces. Comparing the energy release by fracturing or seismic events indicates their contribution to the total amount of released energy or total work. The amount of energy associated with the stick-slip event is small compared with the overall work done to generate the distortions (i.e. increases in aperture by forcing them open) in the rock mass, and much of the energy in slip is lost as heat from the plastic deformation, rather than as radiated seismic energy.Microseismic monitoring shows the spatial distribution and magnitude of seismicity associated with slip of bedding planes and natural and incipient fractures. Work calculations have been undertaken to look at the various sources of energy storage (elastic strain energy) or dissipation (slip), and likely the energy losses from viscous dissipation could be addressed as well, helping to clarify HF processes in NFRs."

Jan 1, 2015

By John N. Ludden, Maurice Rive, Hillar Pintson

"Quelques soixante-dix-sept plutons présents dans la Sous-Province de Pontiac et dans la partie centrale de la Sous-Province de I’Abitibi ont fait I ’objet d’une reconnaissance systématique. Ils ont été regroupes en huit suites plutoniques majeures et trois suites mineures à partir de critères géologiques et petro logiques. Parmi les suites majeures, quatre représentent I' activité intrusive la plus ancienne dans la région. L’une d' entre e/les est représentée par deux complexes anorthosito-gabbroi' ques lites et les trois autres comprennent les orthogneiss dioritiques a leucotonalitiques et les intrusions dons la composition varie de diurétique et granodioritique à leucotonalitique. Leur mise en place peut être pretectonique a syn ou tarditectonique; certains plutons sont synvolcaniques. Quelques data/ions U! Pb effectuées à propos de ces roches donnent des âges s' étalant entre 2 718 et 2 694 MA. Les données géochimiques indiquent la présence des deux lignées magmatiques, tholemique et calcoalcaline bien qu’il n'y ait aucune évidence de relations entre elles dans I' espace et dans le temps. Ces suites magmatiques différentes peuvent provenir soit d’une croute tholemique impliquée dans un processus de subduction soit directement du manteau.Les trois autres suites majeures comprenant des monzodiorites, des granodiorites et des monzonites ainsi que les deux suites mineures comprenant des syenites correspondent à un évènement intrusif plus jeunesse déroulant entre2 694 et2 680 MA. Ces roches sont syn, tarti a post tectoniques et sont enrichies en alcalins, Ba, Sr et terres rares legeres par rapport aux quatre suites précédentes. Leurs caractères chimiques prop res suggèrent qu' e/les proviennent d' une source différente par rapport à celle precedemment citee.La derniere suite plutonique majeure correspond a un monzogranite leucocrate, riche en pegmatite, également syn a tard tectonique, dont I' age n' est pas connu avec précision. ll représente le seul granite ""vrai"" de la région et dérive d’une anatexie soit des meta sédiments soit des granodiorites-tonalites plus anciennes. La troisième suite plutonique mineure correspond a quatre stocks de granodiorite porphyrique qui n’ont pas été étudiés en détail.ABSTRACTSevenly-sevenplutons have been identified in the east-centra/part of the Abitibi Subprovince and adjacent Pontiac Subprovince. These have been subdivided, on the basis of geological and petrological criteria, into eight major and three minor plutonic suite. Four of the major suite, which represent the oldest intrusive activity in the area, range in composition from dioritic-leucotonalitic orthogneisses to diorite-granodiorite/leucotonalite and include two layered anorthosite- gabbro complexes. Their time of emplacement ranges from pretectonic to syn-late-tectonic and some plutons are synvolcanic. U-Pb zircon ages for these rocks range from 2 718 to 2 694 Ma. Geochemical data indicate the presence of both calc-alkaline and tholeiitic magma series for these rocks although there is no evidence time and space relationships between the two. The different magma series also suggest the derivation of these rocks from two sources, either from subduced tholeiitic crust or directly from the mantle. Three major monzodiorite-granodiorite, monzonite, and two minor syenite suites comprise a younger inlrusive event ranging from 2 694 to 2 680 Ma in age. These rocks are syn-, late- to post-tectonica and, compared to the above four plutonic suites, are enriched in alkalis, Ba, Sr and light Rare Earth Elements.Their distinctive geochemistry suggests that these rocks were derived from a different source region than for the older plutonic suites. The remaining major plutonic suite consists of leucocratic, pegmatite-rich, monzogranite-granodiorite. These rocks are also syn- to late-tectonic but their ages are not known with precision. They are the only ""true"" granites in the area and were derived by the partial melting of either older"

Jan 1, 1990

By W. H. MacLean, S. Liaghat

The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographic means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8070 carbonate, 6% chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/ybN = 1.7 to 2.8, SiO2 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y = 9, LaN/YbN= 4 to 8, SiO2 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of FeP3 (27% total iron), Si02 (14%), Cao (8%), S and K2 (+ 2%), were added, Nap was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By Shila Jafari, Mari Lundström, Aleksei Kritskii, Pia Sinisalo

A typical process adopted at nickel plant is the processing of nickel-copper mattes and converter mattes using the following technology: pressure oxidative leaching (POX), solvent extraction (SX), electrowinning (EW), cobalt recovery, and solutions purification. As a result of multi-stage atmospheric and autoclave process leaching, copper-nickel separation is achieved. Cobalt and nickel are further separated by SX. Copper in the process can be removed as copper cake (Cu-cake), which is a by-product with high content of valuable metals. In the current paper, a method combining atmospheric and pressure leaching of Cu-cake in sulfuric-acid media is discussed. Suggested method allows to obtain high copper extraction (>98%), with leach residue containing precious metals and PGMs. Sulfuric acid media was chosen to make the suggested technology adaptable for the primary POX-SX-EW circuit. The initial Cu-cake was analysed and a range of process parameters (t = 25–190°C; PO2 = 0–7 bar) investigated to achieve the optimal conditions for leaching process at the ambient as well as at increased pressure. As a result, an initial process block diagram for the treatment of Cu-cake with high copper leaching efficiency and low metal losses is provided. INTRODUCTION The conventional technology for nickel sulphide ore processing includes the following main stages: froth flotation, matte smelting and converting. The subsequent processing of nickel converter matte is possible using fundamentally different approaches - hydrometallurgical (Llanos, Queneau & Rickard, 1974; Rademan, Lorenzen & Van Deventer, 1999; Kshumaneva, Kasikov, Neradovskii & Belyaevskii, 2009; Dutrizac & Chen, 2013) and pyrometallurgical (Tsymbulov, Knyazev, Tsemekman & Golov, 2007). Hydrometallurgical approach in comparison with pyro-process has several advantages, such as reduced environmental load, reduced PGM losses, increased copper and nickel extraction. Typically, hydrometallurgical technologies include leaching, solvent extraction as well as nickel and cobalt recovery in metallic form by electrowinning or hydrogen reduction or as valuable metal salts via crystallization process (Crundwell, Moats, Ramachandran, Robinson & Davenport, 2011).

Jan 1, 2019

By A. Eslami

When producing high grade mattes in smelter plants, copper losses in the slag are inevitable. Hence, the recovery of copper from slag has been the focus of many research projects, copper flotation being a widely used process. In the Khatoonabad converter, 200 t/d of slag are presently produced with a grade of 2.3% Cu. Assuming a 85% recovery by flotation, about 3.9 t/d copper could be produced, which is of prime importance economically. In the present work, a sample of this slag was crushed and ground in the laboratory to liberate the copper-bearing minerals. Following mineralogical studies, optimum laboratory flotation parameters were obtained, resulting in 90.27 % recovery and 9.42% of copper grade for the rougher stage. At pilot scale, a pulp of 28% solids was floated at ph 10.5 using 40 git of Z6, 25 git of R407 and 20 git of MIBC and A65. A recovery of 83.52% was obtained for a concentrate grade of 28.36% Cu. In the rougher cells, the feed consisted of particles 94% finer than 74 microns whereas in the cleaning stage, particles were 95% finer than 44 microns. Based on the obtained results, the Sarcheshmeh Khatoonabad converter slag is presently being fed to the Chargonbad flotation plant, where a concentrate of 32% copper at 86% recovery is being produced.

Jan 1, 2007

By Atul Bhatnagar, M. P. Sinha, Md Zahid Ahmad, Pallav Garg, Sanjay Kumar Singh, Shashi Ranjan, An Ecolab Company Nalco Water

"Froth Flotation is undoubtedly one of the most critical processes in coking coal washing plants. This work was carried out at Bhelatand Coal Preparation Plant of Tata Steel was with an objective of cost optimization in fine coal processing. The sources of raw coal for the plant include coal from underground mines of Jharia coalfield and procured open-cast raw coal. Coal from different sources vary in quality and possess different floatability characteristics.Synthetic collector is being used in plant as a flotation reagent. An alternate collector with new chemistry was developed for reducing total treatment cost without compromising product yield and quality. A series of laboratory tests were conducted to assess the performance of various sources of raw coal and plant scale trial was started. At first, the new generation coal collector was entirely substituted with the existing collector in the laboratory scale. However the plant scale trial data was not in accordance with laboratory results and indicated inferior flotation performanceThe issue was studied and data based conclusions were drawn that the new generation collector aids faster and uncontrollable kinetics. A decision was taken for co-dosing of the synthetic and new collector for the second phase of the trial. A detailed laboratory analysis was done again and few dosing ratios that predicted optimum results were selected for plant trial. The dosing ratio was optimised as per flotation yield and product ashes during the plant trial. The results showed significant improvement from the first phase and optimum dosing rates were decided based on plant observations and data collection. The influence of various process indicators including water quality, feed and product ashes and process yield was studied during all the trials and promising results were established. The co-dosing of both the collectors conferred cost advantage and enabled to achieve superior performance."

Jan 1, 2016

By Ben C. McLellan, Philip J. Bangerter, Andrew Murphy, Glen D. Corder, Damien Giurco

Sustainability now forms a critical part of metallurgical plant design. In addition to compliance with requirements and corporate principles, design engineers must also consider how community and societal responses to the metallurgical industry affect the way they design and build plants. Three broad areas to consider are: the design engineer’s contribution to sustainability through the design process and the relationship to the social license to operate (SLO)—the unwritten license communities give companies to safely and responsibly operate the plant and equitably share benefits; the realization of sustainability goals through methodologies emerging in the design activities; and the integration of design frameworks into a contemporary project design context and its investment objectives. This chapter explores sustainability in metallurgical plant design in the context of SLO, design tools and frameworks, and community and societal influences.

Jan 1, 2015

By T. W. Wlodek

In this paper the relative merits of shot peening, induction surface hardening, spiral-rolling, and the combination of these surface treatments, are evaluated on the basis of their capacity to increase the fatigue strength of drill steel. The S-N relations for plain car-bon steel (SAE 1080) and Ni-Cr-Mo drill steels in the as-rolled condition were determined previously, using the new Canadian method of testing drill steel introduced at the annual meeting of the Institute in Toronto in 1950 (19). S-N curves have now been determined by this method for these two drill steels in the following conditions: shot-peened and drawn, induction hardened, induction hardened and shot-peened, and spiral-rolled. ( S.R.) . The ratios of the fatigue strengths of these steels after surface treatment, to their fatigue strengths in the as-rolled condition, are compared and the most beneficial treatments are thereby pointed out. The expected range of stresses and their distribution during actual drilling operations are estimated from data available, and the mechanism of failure of drill steel in the as-rolled and surface-treated conditions is analyzed. The magnitude of the surface compression stresses and their effect on ?fatigue strength are discussed.

Jan 1, 1958

By S. Konetschnik, Lux Degel, R. Degel, T. Haslinger

UrbanGold and its partners from Mettop and SMS group have developed a novel technology for the recovery of valuables from all non-ferrous metals’ fractions of WEEE (Waste Electrical and Electronic Equipment), with a special focus on low qualities which are commonly landfilled or incinerated. The technology is marketed under the brand name “UrbanGold Flex” to illustrate the high flexibility in respect of plant design and raw material portfolio, allowing also the processing of low grade material and materials with high caloric values. The process of the technology’s centrepiece, a modified and enhanced bath smelting furnace called “HENRI”, was investigated in numerous pyrometallurgical trials as basis for a scale-up towards a capacity of up to 100,000 tons of WEEE-concentrates per year. All relevant facility components have been evaluated in respect of references, fall-back options, as well as exit strategies (alternatives) to minimize risks when establishing a novel technology. A spin-off within the development is the “UrbanGold Compact” technology which can be seen as optimization of state-of-the-art smelters by using an optimized TBRC as primary processing unit. As an UrbanGold Compact plant will be the first industrial scale reference of UrbanGold’s technologies, it is also explained in the publication. As precious metals recovery is of major (economical) importance when recycling WEEE, major attention has been given to minimize the losses of these valuables. These measures, as well as a sophisticated way of utilizing waste heat as far as possible, result in interesting business cases with gross profits of up to 20% or even more. INTRODUCTION Over the past years, the demand of electrical and electronic equipment has increased dramatically with technological progress. Innovations on the technology of electronic devices led to a shorter usage and lifespan and thus boosted the generation of Waste Electrical and Electronic Equipment (WEEE). WEEE is one of the fastest growing waste streams, growing at 3 to 4% per year worldwide and is expected to reach more than 52 million tons per year by 2021. Currently, about 45 Mt of these wastes are estimated to arise worldwide, and the trend is rising (Baldé et al., 2017).

Jan 1, 2019