Search Documents

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By Michael DeLallo

Clean Coal Technology (CCT) ?Technologies designed to enhance both the efficiency and the environmental acceptability of coal extraction, preparation and use?. These technologies reduce emissions, reduce wastes, and increase the amount of energy gained form each ton of coal extracted and converted into energy. ?? Carbon Capture and Sequestration are an integral part of CCT either as constructed or on a future retrofit basis.

May 1, 2008

By X Dai

This paper investigated the loss of cyanide via oxidation in CIP or CIL processes by relating the cyanide oxidation to its major oxidation product, cyanate. The results showed that the oxidation of both free cyanide and copper cyanide complexes are substantially enhanced by the presence of carbon. The rate of cyanide oxidation was found to occur in the order: Cu(CN)32- > CN- > Cu(CN)2-. The cyanide oxidation rate in the presence of copper and carbon increased significantly with increasing dissolved oxygen concentration, typical of CIL vs. CIP conditions. Cyanide oxidation rate of iron, zinc or nickel cyanide complexes was minimal.

Jan 1, 2011

By N. Shi, T. G. Joseph

ABSTRACTA series of algorithms were developed to perform geometric and kinematic analyses of cable shovel dipper-ground interactions for a given set of mining face conditions. The routines examine and analyze (a) the position of the dipper in relation to the shovel; (b) the dipper in relation to the face conditions; (c) the dipper position in relation to possible interference or collision with crawler tracks during digging cycles; and (d) kinematic and geometric considerations with respect to any point on the dip-per as it conducts a duty cycle. In all cases, field measurement verifcation provided good agreement(within 4% variance).

Jan 1, 2011

By Louise Corriveau, Bronwyn Azar, Valerie A. Jackson, Luke Ootes, Jeff Harris

We use the results of new bedrock mapping, combined with geochemical point data and airborne radiometric data (in particular equivalent uranium concentrations) to help determine which geological units in the Paleoproterozoic Great Bear magmatic zone (GBmz) contain elevated uranium. The data collectively indicate that the highest primary uranium concentrations are in equigranular granites and subvolcanic/volcanic porphyries. Notably, these rocks host the majority of known uranium-bearing deposits and/or prospects in the GBmz. We speculate that the uranium in these deposits/prospects was derived from nearby, uranium-enriched rocks and was mobilized by much younger, circulating hydrothermal fluids. Sedimentary rocks of the Thelon and Dismal Lakes groups unconformably overlie the GBmz and are known to host unconformity-type and sandstone-hosted uranium prospects. Most likely, the uraniumenriched rocks of the GBmz acted as a uranium donor to these overlying sedimentary basins. The method of investigation employed in this study may be applicable to other ‘granitic’ terrains in order to identify regions with favourable rocks for uranium exploration.

Jan 1, 2013

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By Owen Matthews

Introduction For the past year and a half, the mill of Cochenour Willans Gold Mines, Limited, McKenzie Island, Ontario has been roasting arsenopyrite-gold concentrates, prior to cyanidation, by means of a roaster employing techniques that are new and novel. The roaster is known as the Dorrco 'fluo-solids reactor', and the technique as 'fluidization'. The reactor has demonstrated its ability to roast a flotation concentrate containing arsenopyrite, pyrite, stibnite, small quantities of other sulphides, and some lime silicates and carbonates, yielding a calcine consisting mainly of porous iron oxide, plus the gold values. This calcine is readily amenable to cyanidation. Bulk shipments of concentrates to a distant custom smelter, as practised prior to this installation, has thus been eliminated, with appreciable savings in smelting charges, freight costs, and interest losses during shipment and smelting. This is the pioneer installation of fluo-solids roasting at a Canadian mill and up to the present performance results have not been published. It is the purpose of this paper to present the information now available for the benefit of other millmen who may be confronted with identical or similar problems to those encountered and solved at Cochenour Willans.

Jan 1, 1949

By H. R. Manouchehri

"It is well understood that, apart from particle hydrophobicity, the flotation process is strongly influenced by the cell hydrodynamics. Once the chemical conditions were optimized and fixed, the flotation rate is essentially determined by impeller speed and the air flow rate.The collection efficiency in flotation is a product of collision, attachment and stability/detachment efficiencies. The collision efficiency for a given particle diameter is increased by decreasing the bubble size and bubble velocity as well as increasing the power input to the cell. The attachment efficiency, however, is defined by bubble size and its velocity. The detachment/stability depends on the relative magnitudes of the attachment force between the bubble and particles and the detachment force acting on the bubble-particle aggregates. For the particles having specific contact angle, the stability decreases as the energy input increases. Therefore, there must be an optimum energy dissipation to maximize recover of defined size fraction.A comprehensive laboratory study was devoted to determine the effect of power input in recovery of finely grind Cu-Ni bearing ore. Several flotation tests were conducted to define the hydrodynamic parameters for a laboratory scale Runge cell under different impeller speeds. An increase in flotation recovery of finely ground ore was observed when the impeller speed was increased from 450 to 1,200 rpm. The experimental results have shown increasing in water recovery and improving in flotation kinetics of fines by increasing the power input to the flotation cell. Implementation of the Wark flotation model to the experimental data revealed a good correlation between the experimental data and the model. For the particles having enough hydrophobicity the flotation rate increases by increasing the impeller speed due to a higher value for collision efficiency within the cell."

Jan 1, 2016

In Canada and other countries, legislation dealing with accurate factual disclosure for mining projects is being expanded to include more metallurgical design information. Grinding characteristics, metallurgical recovery of contained metal and environmental hazards associated with tailings disposal will be part of the Canadian package. This paper will examine only that portion of the plant design standard practice that relates to grinding ? in SAG mills and ball mills that grind ore from as received crushed material to final ground product that is fed to downstream plant recovery processes. Since grinding plants represent a significant portion of the overall concentrator cost, accountability in grinding design should no longer be left to chance, opinion, or hidden proprietary information. This is the 21st century. It is reasonable to expect that a factual basis will be needed so that a Qualified Person (QP) reviewing the grinding mill design can understand it. That will also involve how many and what quality of samples are taken to define the characteristics of the deposit, the accuracy of the tests used to measure ore hardness and the method by which the dimensions and power of the mills are determined. If these criteria are not met, the QP may have no choice but to call attention to the lack of convincing information regarding the grinding mill design for the project. At the same time clients are expected to demand getting the correct design information at a cheaper price, results in a more timely way, and accurate design to the point where the risk of tonnage shortfalls are reduced or eliminated. Tables will be presented to show how this can be done to current standards using existing technologies. At the same time it is acknowledged that current standards are ill-defined and that to achieve consensus among those involved in SAG mill design work, it may require that a consortium funded project be set up to establish what tests and methods for grinding design are suitable to meet the new standards for metallurgical disclosure. By running parallel design methods on several major projects over a period of 5 years, the process of how to design grinding circuits will be better understood because the projects will start at the design stage, include procurement of the mills and will end with a benchmark test on the plant. Selecting the samples and the best schedule for doing test work on core samples submitted and mill design, will be discussed in this paper. The issue of completing the grinding design in time for early procurement decisions is on the critical path for most major projects. Discussions between mining engineers, geologists and process engineers are needed early in the development cycle, at the scoping study level (SS), preliminary engineering assessment (PEA), prefeasibility study (PFS), and at the feasibility study stage (FS), to ensure that proper planning for design sample selection is done. Using adequate sampling and testing methods in a timely way allows early procurement of the grinding mills and minimizes project risk.

Jan 1, 2012

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of variables, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

By X. Cao, P. Wanjara, J. L. Fihey, X-T. Pham, F. Mirakhorli

Single-pass hybrid laser-arc welding of 10-mm thick cast plates of CA6NM, a low carbon martensitic stainless steel, was carried out in butt joint configuration using a continuous wave fiber laser at its maximum power of 5.2 kW over welding speeds ranging from 0.75 m/min to 1.2 m/min. The microstructures from the fusion zone to the heat affected zone and base metal were characterized after post-weld tempering at 600°C for 1 hour. From optical and scanning electron microscopy examination, the fusion zone was observed to mainly consist of tempered lath martensite and some residual delta-ferrite. The mechanical properties including microindentation hardness, ultimate tensile strength and Charpy impact energy were evaluated in the post-weld tempered condition and correlated to the microstructures and defects. The ultimate tensile strength and Charpy impact energy values of all the fully penetrated welds in the tempered condition were acceptable according to ASTM, ASME and industrial specifications. The failure mechanisms during tensile deformation and Charpy impact loading were examined by scanning electron microscopy, fractography and optical metallographic analysis near the fracture origin.

Jan 1, 2015

By J. Walker, G. E. Kim

Since May of 2000, Mogas Industries, in partnership with F.W. Gartner Thermal Spraying Co. and using the services of Perpetual Technologies, has invested time, energy, and resources towards developing novel ball valves for high-pressure acid-leach (HPAL) service. In addition to developing new valve designs, an aggressive coatings development effort has been undertaken to improve the protective quality of the coatings so as to enhance the performance and extend the life of valves in severe HPAL conditions. In 2001, Mogas Industries qualified and applied a nanostructured titanium oxide (n-TiO2) coating for gold and nickel/cobalt HPAL services. The n-TiO2 coating provided dramatically superior protection against abrasive and erosive wear, fared very well against high-pressure autoclave corrosion testing, and has performed well in HPAL service.

Jan 1, 2004

By James R. Hein

Manganese nodules form at the sediment surface of abyssal plains throughout the global ocean at water depths of about 4000-6500 m. The nodules form a continuum from purely hydrogenetic (all metals from seawater) to purely diagenetic (all metals from sediment pore waters), which will determine which metals of potential economic interest are enriched in the nodules. Another important factor in metal enrichment is whether diagenesis in the bottom sediment is oxic or suboxic. There are several nodule fields in the deep ocean that have received much attention with regards to economic potential, the most important being the Clarion-Clipperton zone (CCZ) in the NE Pacific, where the International Seabed Authority (ISA) has signed 12 contracts for exploration areas, each spanning 75,000 square kilometers. Those nodules are rich in nickel (mean 1.3 wt. %), copper (mean 1.1 %), and manganese (28%), with moderate amounts of cobalt (mean 0.2%), molybdenum (587 g/t), and lithium (129 g/t). A conservative estimate is that there exists 21,100 million dry tonnes of nodules in the CCZ, yielding more manganese, twice the nickel, three times the cobalt, and four times the yttrium than the entire land-based reserve base (economic plus marginally economic plus subeconomic reserves) for each metal. Total rare-earth elements (REEs) as oxides average 0.09% in CCZ nodules, a potential byproduct even at that grade because the heavy REE complement averages 26%, compared to less than 1% for the large land-based carbonatite REE deposits. The price for HREEs is much greater than for the light REEs. For comparison, the REEs in deep-ocean ferromanganese crusts are 3 to 5 times greater than nodules and the HREE complement averages 18%. Of the 12 CCZ contracts, 7 are with States (China, France, Germany, Japan, Korea, Russia, and a group of States (IOM); and 5 are with companies: G-Tec Sea Mineral Resources NV, Nauru Ocean Resources Inc. (NORI); Tonga Offshore Mining Ltd (TOML), UK Seabed Resources Ltd (Lockheed UK), and Marawa Research and Exploration Ltd. Three other nodule fields that have received attention are in the Peru Basin, which has nodules very rich in manganese (34%) and lithium (mean 311 g/t), the Penrhyn Basin (Cook Islands Exclusive Economic Zone), with nodules very rich in cobalt (mean 0.4%); and the Central Indian Ocean Basin (CIOB), where India has an exploration contract with the ISA. CIPB nodules have mean nickel, copper, and manganese contents of 1.1%, 1.0%, and 24% respectively.

May 1, 2013

By J. Locat, G. Parker, D. Turmel

ABSTRACT Since 1964, the Iron Ore Company of Canada has deposited iron ore tailings into Wabush Lake in western Labrador, Canada. From 1999 to 2008, the authors completed multibeam bathymetric and sampling surveys and an airborne LiDAR survey. These data were integrated to study the evolution of the tailings delta shoreline and lakebed elevation. Subaqueous channels evolved between surveys, influencing the tailings depositional pattern. With this analysis it is possible to evaluate the effect of disposal strategies on the delta topset and tailings accumulation. This project uniquely couples marine and terrestrial techniques to follow the fate of tailings in a dispersal system.

Jan 1, 2014

Who is CIBC? ? Canadian Imperial Bank of Commerce (?CIBC?) is a leading North American financial institution. ? Total Assets: US$315 billion ? Market Capitalization: US$29 billion ? CIBC comprises three strategic business lines: ? CIBC Retail Bank ? CIBC Wealth Management ? CIBC Wholesale Bank ? CIBC Wholesale Bank is a leading North American investment bank with niche capabilities in Asia, Australia & Europe. ? 1,000 + employees around the world ? Product range includes: Mergers & Acquisitions advisory and financing, Equity and Debt issues, Merchant Banking and Strategic Lending ? CIBC is ranked as the #1 investment bank in Canada across most of its key products and industries ? #1 Equity Underwriter in Canada ? #1 Mergers & Acquisitions Advisor in Canada

May 1, 2010

By A. J. Miller

Estimates of interstitial water saturation derived from capillary pres-sure data are compared with residual water saturations found by the analysis of cores out in oil-base drilling fluid. A theoretical explanation for the high-rate of water production from the Bellshill Lake Field is proposed, based on the interpretation of the capillary pressure data.

Jan 1, 1960

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By P. Chryssanthakis

"The aim of this study is to give a better understanding for the behaviour of the composite material RRS and the synergy effect of its components while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10 m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. The newest part of the lower part of the Q-chart gives more information on required support compared to older Q-system versions. The RRS can be described as a three part composite material with the 3rd component being the reinforced concrete beam (with no fibers) and with steel rebars that are placed in groups and sprayed with pneumatically applied shotcrete in layers. The RRS usually have a total thickness varying between 0.20 and 0.50 m and a width between 0.25 and 0.60 m respectively. They are placed at different distances along the tunnel axis depending on the rock mass quality.In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. This was done by writing a FISH subroutine which is implemented in the discontinuous numerical code Universal Distinct Element Code (UDEC) that takes into account the characteristics of the reinforced beam (height, width, number of steel rebars, and spacing) in the calculation process. A rather extensive parametric study has been run by using the same key input rock mass parameters and in situ stresses (?H/?v = 0.5), and changing only the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam.The results show that: a) the S(fr) is almost overloaded in the first 4 hours after application in both tunnels; b) on the S(fr) and steel rebars, the stresses, axial and shear loads, as well as moments are decreasing after 16 hours and 28 days; and c) the bolts loads are increasing with time. The observed reduction in stresses and loads in both the S(fr) and reinforced beam is surprising. A possible explanation is that tunnel arches are self-supported to a lesser extent as time progresses due to redistribution of stresses in the nearby rock mass through the radial bolts. The loads in radial bolts are increasing by almost 25%. This can be seen from the overall results as we observe an increase in maximum principal stresses, displacements, shear displacements along joints and hydraulic apertures compared to tunnel baseline that has no support of any kind."

Jan 1, 2015

By Pierre Laliberté

L?utilisation de plusieurs nouvelles technologies et systèmes de contrôle visant des économies d?énergie dans une exploitation minière pourrait laisser croire qu?il suffit d?additionner les économies potentielles de chacune de ces technologies pour en évaluer l?économie totale. Une addition simpliste des pourcentages d?économie pourrait, dans certains cas, dépasser 100%, ce qui est évidemment totalement incohérent. Les LMSM-CANMET sont à réaliser une étude dont les résultats serviront à estimer l?influence de certaines technologies et systèmes de contrôle visant des économies d?énergie et à évaluer l?impact des unes sur les autres. En outre, un modèle de simulation est en cours de création afin d?évaluer les gains incrémentaux liés à l?application d?une série d?innovations dans une exploitation minière. La présentation fera le point sur l'état d'avancement du projet en plus de soumettre quelques exemples.

May 1, 2007