Search Documents

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

By Paul R. Clark

Outline ? Coal As An Energy Resource ? Canadian Clean Power Coalition ? Phase I of the CCPC Project ? CO2 capture options ? Gasification ? CO2 use ? Results ? Phase II Plans ? Next Steps TransAlta - Profile ? 9,726 megawatts (MW) of capacity ? 46,877 gigawatt hours (GWh) produced at an average plant availability of 88.4% ? 47 facilities in four geographies: Canada; the U.S.; Mexico; and Australia ? Fuel mix of coal (62%), gas (26%), hydro and renewables (12%) ? 23.2 million tonnes of coal mined ? 47.0 million gigajoules (GJ) of gas consumed

May 1, 2004

By G. Shore

Radiation grafted structures my be fabricated to contain ion exchange groups selective to an ion complex. Proper choice of substrate and monomer will provide selective ion exchange with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures have been fabricated to ''capture'' gold, silver and palladium from dilute solutions. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their regenerating solutions are pure metal foil.

Jan 1, 1985

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability.The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employees to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed. IntroductionThis article is the second of three on predictive maintenance at the Louvicourt mine operated by Aur Resources Inc. The first article, published in the October 2002 issue, was about vibration analysis for rotating machines. This article describes how lubrication and oil analysis for stationary machines permitted Louvicourt to save more than $150,000 within two years and presents the evolution of the oil analysis program.Louvicourt mine, located near Val-d’Or, Quebec, is a copper and zinc mining and milling operation that processes 4300 t/d of ore and employs 289 people. Production began in 1994. Louvicourt mine is a partnership between Aur Ressources (30%), Teck Corp. (25%), and Novicourt (45%)."

Jan 1, 2003

By Terry Braden

"Meeting probable world mineral demand in the years ahead will almost certainly require an ability to economically treat lower grade and more complex ores. Achieving this will require extensive research and technical development across the full spectrum of mineral processing.For mid-sized or smaller companies the most effective way to participate in such extensive programs - and gain access to the technology required to stay competitive - may be through collaborative research.This paper explores the recent history of collaborative research in mineral processing and in particular its ability to attract world-class multi-institutional research teams with sufficient resources to make step-change advances. It chronicles the advances achieved, but also explores the research architecture and administrative structures required to deliver research outcomes and technology transfer mechanisms to a range of often disparate sponsoring companies.INTRODUCTIONIn medieval times the dream of alchemists was to turn base metals into gold. We modern alchemists, of course, don’t waste our time on that sort of foolishness: we turn base metals into dollars. When I see the profit reports filed by some companies recently, I can only conclude that a lot of those present today must be pretty good at this.But the fact that we are here at this conference reminds us that an alchemist’s work is never done; turning base metals into dollars is not a one-trick wonder but an art that we must extensively refine year after year if we are to survive in a competitive marketplace.It is not that demand for metals is likely to slow; most people seem to think that China, India, Brazil and other emerging economies are still at the lower end of their demand curve. They will need significantly larger volumes of metals in the years ahead. The challenge for us as processors is that to supply increasing tonnages of those metals profitably we will almost certainly need to process more complex or lower grade ores and probably to do so with reduced energy inputs."

Jan 1, 2009

By R. Laplante, P. Radziszewski, P. De Ciccio

"Predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case. Wear conditions vary with geological formations and compositions. The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American drilling campaigns. Simulation results allow the definition of simple graphical tools that permit the estimation of the potential drill depth remaining on a given drill rod string. IntroductionWear, in many industrial processes, is an undesired phenomenon for which enormous efforts are made to control, if not eliminate. However, wear, in many other cases, is an intrinsic phenomenon of the given process. In such cases, predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case where abrasive conditions vary with geological formations and compositions.A number of studies have been published on drill rod wear especially with regards to the petroleum industry over the last thirty years (Lewis, 1968; Rollins, 1968; Smith, 1978; White 1978; Rowe and Wilson, 1981; Cheng, 1982; Eustes, 1986; Dudman et al., 1989; Besaisow et al., 1990). Of these, most studies covered management techniques (Rollins, 1968; Smith, 1978; White, 1978; Rowe and Wilson, 1981; Besaisow et al., 1990) and some described case histories (Cheng, 1982; Eustes, 1986; Dudman et al., 1989). However, little (Lewis, 1968) was presented that could aid in predicting wear in the particular case of diamond drilling in the metal mining industry.The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate diamond drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American diamond drilling campaigns."

Jan 1, 2002

By Jean-François Lessard

The performance of rock pass systems has a significant contribution to the economics of underground mines. Operational concerns include hang-ups due to arching of material, blockage and degradation of the rock pass. This papers presents the preliminary results of a comprehensive rock pass database on the engineering and operation of rock pass systems in Quebec underground mines.

May 1, 2002

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hard rock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

May 1, 2007

What is the BC AMTA? ?What is an ASEP? ?Who are the partners? ?Critical Success Factors ?Questions/Answers Aboriginal Skills and Employment Program (ASEP) ?A collaborative partnership of industry, employers, post secondary, First Nations and government ?Working together to plan and implement training and education programs ?Demand-driven: targeted JOBS for participants

May 1, 2010

By C. O. Brawner, J. Kalejta II

"The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than approximately 45 degrees.As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result in less rock fall capacity.The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented."

Jan 1, 2002

By L. K. Smith, C. R. May, K. R. Schrag, H. Buchwald

"New contracts for 65 million long tons of coking coal valued at over $900 million, over the next 15 years, herald the rebirth of Alberta's coal industry. The industry is optimistic that export orders may reach 20 million tons per annum by the mid-1970's. Coal will be extracted from underground and surface mines and it is expected that the total labour force will double from the present 1,200 men within the next two years. Ali the health hazards associated with coal mining are likely to be encountered and it will be incombent on the Provincial Department of Health to specify the standards which relate to health and environment where no such standards have previously existed. This paper examines some of the problems which are being encountered in setting up an environmental health program and reviews the practicability of environmental monitoring methods, with special reference to respirable dust."

Jan 1, 1969

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By James A. Finch, Robert E. McIvor

"This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.INITIAL DEVELOPMENT OF THE CIRCUIT MODELThe Functional Performance Equation for Closed Circuit Ball (or Pebble) MillingIt has been shown that closed grinding circuit performance can be effectively characterized by the “functional performance equation” for closed ball or pebble milling circuits (McIvor, 2006a). One method of its derivation is summarized here for convenient reference.First select a cut-off size to define “coarse” versus “fine” or product size material for the grinding circuit. Any particle mesh size can be used to differentiate between coarse material and fines, but the circuit target P80 is often an effective choice for these purposes.Any energy expended on “fines” is wasted. It also generates “extreme fines” often detrimental to downstream processing (McIvor and Finch, 1991). Only the portion of the mill power draw that is expended on coarse material is effectively used. This portion can be estimated from the mill feed and discharge size distributions (McIvor, 1988a) by taking the average of the percentage of “coarse” material in the mill feed and discharge. We can define the thusly calculated percentage of the mill power that is expended on coarse material in the mill as the ball mill circuit “classification system efficiency” (CSEff). The “effective mill power” (EMP) can be calculated from the total mill power (TMP) as follows."

Jan 1, 2007

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

By J. Lazareck

"XPotential Products Inc. has developed technologies to convert auto shredder residues and other forms of plastic waste into useful products such as posts suitable for retaining walls and parking curbs. The technology is competitive provided low-cost plastic waste is available, and could have applications throughout the world. The paper describes the technology used and illustrates the various processing steps. Development of the TechnologyPresently, state-of-the-art auto shredding yields approximately 75% ferrous and non-ferrous metals and approximately 25% by weight of auto shredder residue (ASR). Advances in metal shredding and non-ferrous metal separation technologies turned XPotential Products Inc.’s attention to ASR as a potential revenue source, or at least a means to markedly reduce the cost of disposal. This abundance of nuisance ASR was, in the company’s view, a potential resource as derelict autos and white goods were similarly perceived 40 years ago. As owners of General Scrap & Car Shredder Ltd. in western Canada, XPotential faced significant disposal costs for four shredders. This journey began over 10 years ago and took many twists and turns until a final course of action was chosen. The recovery of the metallic portion of vehicles and white goods has reached technological maturity and attempts to add value are now achievable only in very small increments."

Jan 1, 2004

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By Dianne M. Lapierre

Mining firms in Canada are increasingly incorporating the social and environmental interests of their stakeholders into their projects in an effort to become more sustainable. Such initiatives have included negotiating Impact and Benefit Agreements (IBAs) directly with would-be impacted, often aboriginal, communities near resource developments in the Canadian north. Why does a mining firm take on this extra time-and cost-intensive initiative when governments and regulatory measures are in place to address social and environmental issues? Past research has paid little attention to the corporate rationales for IBAs. Based on document review and interviews with mining executives, this study investigates the rationales of mining firms that ?over-comply? with legislative requirements by negotiating IBAs or similar types of agreements with communities. The results indicate that mining firms increasingly recognize IBAs as an intrinsic part of the permitting process. When queried, executives regularly identified the negotiation of agreements as ?the right thing to do?. While this response could be read in ethical terms, a commercial rationale is also clearly present. By building strong relationships with nearby communities, addressing community concerns, and directing benefits to local people, all of which are explicitly achieved with an IBA, mining firms are maintaining their long-term financial viability, thus their sustainability, within an evolving industry.

May 1, 2008

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"Abstract — The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units. © 2012 Canadian Institute of Mining, Metallurgy and Petroleum. All rights reserved."

Jan 1, 2012

By Baki Özüm

Early evaluations of Pasquia Hills kerogen shale deposits by Geological Survey of Canada, Saskatchewan Geological Survey, Manitoba Energy and Mines and Sun Oil Company, using modified Fischer Assay, Rock-Eval and other techniques, estimated recoverable reserves of about 2.6x109 barrels of oil in areas favorable for strip-mining; each metric ton of ore was determined to yield about 30 L to 50 L of shale oil remarkably high in aromatic compounds. Western Petrochemical Corp. (WPC) is holding two Oil Shale Exploration Permits covering about 76,635 hectares in the Pasquia Hills Region of eastern Saskatchewan and conducting a 15-corehole drilling program to determine stratigraphic correlation on both first and second white specks kerogen shale. In this program, correlation will be established between oil yield and oil quality, using different retort techniques, including modified Fischer Assay, steam retort and Rock-Eval. Results will lead to further resource evaluation and to a preliminary engineering design for a shale processing plant, including selection of retort process, upgrading of shale oil to petrochemical feedstock, hydrogen management, energy balance and evaluation of environmental impact.

May 1, 2002