Search Documents

By R. W. Bartlett

The rates of oxidation of tungsten have been determined at temperatures between 1320" and 3170°C and oxygen pressures to 1 amn using a surface -recession measurement technique. Above approximately 2000°C and 10-6 atm the rate is independent of temperature and can be calculated from gas collision theory assuming a constant reaction probability, e, of 0.06. Oxygen molecules react at surface sites where oxygen atoms have previously chemisorbed. This provides a direct pressure dependence at low pressures but at high pressures tungsten oxide molecule s form an adjacent gas boundary layer which lowers the PO2 at the tungsten surface. A correction for this effect using free-convection theory fits the rate data over the entire oxygen-pressure range from 10-8 to 1 atrn as well as data using O2-A mixtures. Below 10-6 atrn and above 2000°C, e decreases with increasing temperature because of desorption of oxygen atoms. Below 2000°C the rate decreases with decreasing temperature at all oxygen pressures following an apparent activation energy of 42 kcal per mole and depending on (Po2)n with n varying between 0.55 and 0.80. MOST of the previous tungsten oxidation studies have employed gravimetric methods and have been limited to temperatures below 1000°C where the weight loss associated with evaporation of tungsten oxides is negligible compared with the weight gain from oxidation.' At higher temperatures, oxygen-consumption rates have been determined from pressure measurements, usually at constant flow rates, by Langmuir,2 Eisinger,3 Becker, Becker, and Brandes,4 and Anderson.5 The sensitivity of this method decreases with increasing pressure and, with the exception of Langmuir's work, these investigations were confined to pressures below 10-6 atm. Above approximately 1300°C, depending on the oxygen pressure, the rate of oxide evaporation is greater than the oxide-formation rate and the recession of the tungsten surface can be measured optically without interference from an oxide layer. This was first done by Perkins and crooks6 who heated tungsten rods in air pressures from 1 to 40 torr at temperatures between 1300" and 3000°C. The present investigation of the oxidation kinetics of tungsten at high temperatures emphasizes oxygen pressures from 10-6 to 1 atm. This is the range of interest for earth atmosphere re-entry applications of tungsten for which little data were previously available. APPARATUS The apparatus is a modification of the type used by Perkins and crooks.' Ground tungsten seal rods, 6 in. long by 0.125 in. diam, were mounted vertically between two water-cooled electrodes, one fixed and the other having free vertical travel. The movable counter-weighted electrode is prevented from undergoing horizontal displacement by three sets of runners mounted at 120-deg intervals. Electrical contact is made by means of a water-cooled mercury pool. A 24-in. vacuum bell jar having a volume of approximately 267 liters was used as the reaction chamber with the sample holder mounted in the middle of the chamber. Power was supplied from an 800-amp dc variable power supply. Temperature readings were made by means of a Latronics automatic two-color recording pyrometer. With this instrument, corrections for emissivity are not necessary provided the spectral emissivi-ties at two closely spaced wavelengths are equal. Supporting measurements were made with a micro-optical pyrometer corrected for emissivity of bare tungsten and window absorptivity. The micro-optical pyrometer was calibrated against a National Bureau of Standards calibrated tungsten lamp and both pyrometers were periodically checked against the melting points of tungsten and molybdenum using the oxidation apparatus. Above 10-6 atm, pressures were measured with an Alphatron gage calibrated against a McCleod gage. At 10-6 atm, a hot-filament ionization gage was employed. A magnified image of the self-illuminated tungsten rod was formed using a 360-mm objective lens mounted outside the bell jar. When the experiment exceeded 1 hr, the image was focused on a ground-glass plate about 10 ft from the tungsten rod at about X8 and the recession of the thickness of this image was monitored with a Gaertner cathe-tometer. When faster rates were encountered, a 35-mm time-lapse cinecamera with a telephoto lens and bellows extension was substituted for the ground-glass plate and cathetometer. Diameter recession rates were determined from the photograph image projected on the screen of an analytical film reader. EXPERIMENTAL PROCEDURE After installing the rod in the apparatus and cleaning it with acetone, the system was evacuated to 5 1 x 10-5 torr. Before oxygen was introduced,

Jan 1, 1964

By Tell Ertl

An annual invitational address by an outstanding man in mining, geology, or geophysics who has contributed significantly to the progress of technology in these fields. IN 1954, the first year the award was conferred, Fred Searles, Jr., remarked, "The earlier years are the easiest." In this, the second year, it was easy to choose the outstanding mining engineer. Our conferee this year has been destined to mine. He comes from pioneer stock, and though a son of the American Revolution he is most proud that all four of his grandparents came to the Jordan River Valley of Utah the "first summer," which all Utahns will recognize as 1847. At the time of discovery of high-grade ore in Bingham, his grandfather, Archibald Gardner, had a crew of men getting out saw timber in the area. The first claim staked in Bingham Canyon was named the Jordan, and Bishop Gardner was the colocator of the claim as well as the man to record it. E. D. Gardner was born in West Jordan, Utah, in view of Little Cottonwood Canyon, the site of the Emma Mine. Park City in the Wasatch Mountains a few dozen miles to the east, and Tintic, not much further to the south, were developing their vast ore-bodies throughout his youth. As a boy he was near the present Midvale metallurgical area and could see the Lark and Bingham Canyon mine dumps and imagine the mining activities at Tooele, Ophir, and Mercur just over the nearby Oquirrh Range. He was 11 years old when the first car of copper ore was shipped from Bingham Canyon. It was not surprising that he attended the University of Utah and graduated with an engineer of mines degree. Five years with the Utah Apex in Bingham Canyon as chief engineer and assistant superintendent completed his training for the 44 years of unselfish and lightly rewarded service he was to give the mining industry as a Government engineer. All of us in mining are familiar with the great work he carried on and directed during the genera- tion he supervised the Southwest Experimental Station at Tucson. He has written scores of papers and books. His observations and experiments on drilling and blasting have led to the important improvements in this field during the past quarter century. Whereas those of us who consider ourselves widely informed about underground metal mining methods make hasty trips through a half dozen or dozen mines a year, our conferee has visited them all—not only the metal mines, but also coal and hundreds of nonmetallic mines, in the United States, Canada, Latin America, and overseas. His keen observations and analytical mind have resulted in an encyclopedic knowledge of mining and mines. His improvements in mining technology have been steady and predictable. His elucidation of mining problems to the many young engineers that have come under his guidance have made them grow strong and useful to his industry. When he chooses to stop, his influence will continue to expand and prosper because of the inspiration and dedication he instilled in so many of us. The profits from his ideas have been distributed throughout the mining industry. He has remained a technical man who felt that he could serve the mining industry best as a Government engineer. But he is the staunchest advocate of the belief that the public should gain from his work through private industry. This is not the first recognition E. D. Gardner has received. The Department of the Interior awarded him the coveted Medal for Distinguished Service in October 1949, and he received the Engineering & Mining Journal's Salute in March 1951. His friends who are presenting him the Daniel C. Jackling Award today know this great mining engineer simply as "Ed" Gardner.

Jan 1, 1956

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30' to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,' in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.' The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956

By Bezalel C. Haimson

Anna, Ohio, at the junction of Cincinnati, Findlay and Kankakee arches, has been the site of repeated and sometimes damaging earthquakes. As part of a seismicity investigation near-surface (0.15-1 m depth) overcoring strain measurements were conducted in four limestone and dolomite quarries surrounding Anna, the results of which suggest a complicated regional stress pattern, with changes in the maximum horizontal stress direction from N45ºE to N15ºW. Since such abrupt stress fluctuations are rather atypical in the Midwest and since the reliability of near-surface tests in defining regional stress had not been established, we decided to remeasure the stresses at the same locations but at greater depths (0-200 m) using the hydrofracturing method. Owing to the weak horizontal bedding planes of the Silurian shaly limestones and shaly dolomites and the relatively shallow depths, many of the tests yielded horizontal fractures, providing information only on the vertical principal stress (-0.029 MPa/m depth). However, sufficient tests in each of three testholes resulted in vertical hydrofractures to enable the calculation of all three principal stresses. Within 50-170 m depth the horizontal stresses in all three quarries appear to belong to a uniform regional Stress field defined by the following relations: [']Hmin = 5.1 + 0.014 D; [0] Hmax = 10.1 + 0.014 D, where D is depth in meters. The direction of [O]Hmax within 50-170 m depth is uniform at N70°E (±15º). The hydro- fracturing results obtained at Anna, Ohio are in agreement with the prevailing stress regime in the midcontinent both with respect to magnitudes and directions. The results suggest a possible thrust mechanism for a proposed NW-SE fault along which most of the earthquake epicenters have been located, and a left lateral strike-slip at greater depths. The focal mechanism solution of a recent major earthquake near Sharpsburg, Kentucky, some 200 km south of Anna, also indicates strike-

Jan 1, 1982

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,' a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

By Hans-Jürgen Schaller, Horst A. Brodowsky

Activity coefficients of boron in palladium were determined at concentrations up to PdB0.23 by reducing B2O3 between 870" and 1050°C in a controlled H2-H2stream and measuring the resulting weight gain. The deviations from ideal behavior closely resemble those of the system Pd-H and are interpreted in terms of three principles: 1) The solute atoms occupy octahedral interstitial positions. 2) They donate their valence electrons to the 4 d and 5s bands of palladium, raising its Fermi energy. 3) The lattice strain energy is lower for two nearesl -neighbor interstitial particles than for two farther separate ones. SOLID solutions of hydrogen in palladium are a useful subject for studying thermodynamic aspects of the formation of alloys and of nonstoichiometric systems.1-3 The activity of hydrogen is readily measurable to a high degree of accuracy,4'5 even at low temperatures where the deviations from ideal behavior are more pronounced, and its simple structure facilitates an interpretation of these deviations in terms of a detailed model. Two effects are discussed to account for the non-ideal properties:3 An "electronic" effect, connected with the rise of the Fermi energy, as electrons of the interstitial hydrogen atoms enter the electron gas of the metal, and an "elastic" effect, due to an interaction of the regions of strain around each interstitial atom. The electronic effect is based on the idea that the lowest energy levels of the dissolved hydrogen atoms are higher than the Fermi energy, so that the electron will not occupy a localized state but enter into the electron band of the metal.6 The elastic effect is based on the observation that dissolved hydrogen distorts and expands the palladium lattice. The hypothesis is put forward that the elastic strain energy is lower for two adjacent dilatational centers than for two separate ones; i.e., they attract each other. The resulting pair interaction can be used to calculate an elastic contribution to the thermodynamic excess functions by means of one of the statistical methods. This model permitted a detailed description of the solution properties of hydrogen in palladium3 and in palladium alloys.798 An extension of the approach to describe the excess functions of substitutional palladium alloys is possible.9 In order to further test and refine the model, an investigation of other interstitial alloys was started. Palladium dissolves considerable amounts of boron in homogeneous solid solution.10 The palladium lattice expands linearly up to nB = 0.23 (nB = B/Pd atomic ratio), the highest concentration studied." The expan- sion, extrapolated for 1 mole of interstitial per mole of palladium, is 17 pct of the lattice constant of pure palladium vs 5.7 pct in the case of hydrogen.12 The fact that the lattice expands rather than contracts is a strong indication that interstitial positions are occupied. According to neutron diffraction experiments, hydrogen occupies the octahedral sites of the fcc lattice.13 Unfortunately, this direct evidence is not available for the Pb-B system, mainly because of the high-reaction cross section of boron with thermal neutrons. However, by way of analogy and on the grounds of the rather close similarities between the two systems to be reported here, it seems safe to attribute octahedral positions to the dissolved boron, too. At higher boron contents, compounds of stoichiomet-ric compositions are reported such as Pd3B, which has the structure of cementite,14 so that a close structural relationship seems to exist with the system r Fe-C. In their study of hydrogen absorption in Pb-B alloys, Sieverts and Briining noted that alloys with an atomic ratio of about nB = 0.16 are no longer homogeneous15 This observation was confirmed in an extensive X-ray investigation.11,16 The phase boundaries of two miscibility gaps were established. One two-phase region was stable below a transition temperature of about 315°C and extended from nB = 0.015 to 0.178. The other one extended from nB = 0.021 to 0.114 slightly above the transition temperature and had an apex at nB = 0.065 and 410°C. All phases involved have the fcc structure of pure palladium with lattice expansions proportional to their boron contents. The occurrence of miscibility gaps, i.e., the coexistence of dilute and concentrated phases, points to an energy of attraction between the dissolved particles, in the Pb-B system as well as in the Pd-H system. The filling up of the electron bands seems to be analogous, too, in the two systems, as indicated by the hydrogen absorption capacit15,17,18 and by the suscepti bility of Pd-B alloys.l8 In both types of experiments, boron acts as an electron donor. A chemical method was used to measure the activity of boron in palladium. Boron trioxide was reduced in a moist hydrogen stream: B2O3 + 3H2 = 2B + 3H3O [l] At known activities or partial pressures of boron trioxide, hydrogen, and water, the activity of boron could be calculated from the law of mass action. The equilibrium concentration of boron corresponding to this activity was determined as the weight gain of the sample. EXPERIMENTAL The samples consisted of small pieces of foil of 0.1 mm thickness and about 100 mg weight. The palladium was supplied by DEGUSSA, Germany, and stated to be

Jan 1, 1970

By R. E. Miner, J. K. Jackson, T. L. Wilson

A study has been made of the transformation kintetics and morphology in gas-quenched Fe-5 pct Ni alloys. Massive ferrite or nlurtensite was found to form at temperatures in agreement with earlier results. Surface Preparation appeared to have the greatest effect in determining the type of transformation Product formed. Grain size change, subgrain morphology, and dislocation densities of massive ferrite were essen-tinlly invariant functions of cooling rate. The mar-tens~tic structures were typical of transformation in austenite grains of the order of the sample thickness. BY introducing the idea of a massive transformation in dilute iron-base alloys, Gilbert and Owen in 1962 served to stimulate a closer inspection of phase transformations in ferrous systems.' A wealth of literature has followed concerned with the morphology,2-5 transformation mode,2'3'6-8 and thermodynamics of transformations.2,5,9 interesting controversies have resulted from the experimental observations; closer attention has been paid to the definition of massive transformations and still to be resolved is the Ms temperature of pure iron. The purpose of this note is to report some observations made in a detailed kinetic and metallographic examination of the transformations that occur in gas quenched Fe-5 pct Ni. The results are pertinent to the Ms extrapolations that have been made for pure iron and the observed substructure of massively transformed alloys. PROCEDURE The material used in this investigation was cast as a 5 lb vacuum induction melted, carbon deoxidized heat. The ingot was hot worked to a strip 0.10 in. thick, decarburized, and cold rolled to final thickness. Specimens were punched to sample shape and decarburized in wet hydrogen at 600°C. The chemistry of test specimens is indicated in Table I. Samples 1 by $ in., by thickness were resistance heated and rapidly cooled in an apparatus as illustrated in Fig. 1. Similar helium quenching apparatuses have been described previously;2,6'10 the distinguishing feature of this apparatus is the nozzle geometry. Twin nozzles with three convergent-divergent, sonic ports were mounted perpendicular to the specimen for quenching purposes. The specimen temperature was monitored with an intrinsic 3 mil chromel-alumel thermocouple spot welded to the specimen and con- nected to an oscilloscope. A single switch stopped the current flow through the specimen, opened a gas flow solenoid valve, and initiated an oscilloscope sweep. Cooling rates were read directly from a photograph of the oscilloscope trace and the quenching rates quoted later were made at a point immediately prior to transformation on the trace. All quenching studies were conducted either under a vacuum of 10"-5 torr or a helium atmosphere. The sample geometry was chosen large enough to permit optical and electron microscopy to be performed on samples. The samples were electropolished for both types of examination in a perchloric-acetic solution. Electron microscopy was conducted on a HU 11A microscope operated at 100 kv. Dislocation densities were determined at the same general operating reflection (110) on foils thick enough to produce Kikuchi patterns. RESULTS AND DISCUSSION Transformation Temperature Observations and OD-tical Microscopy. The quenching results of this study are illustrated in Fig. -2(a). Samples which were treated in the as-decarburized condition transformed in a manner similar to that reported previously—a decrease in transformation temperature occurred as the quenching rate increased until a plateau region was reached. Within the scatter of the results obtained here, there was no break in the transformation temperature-quenching rate plot. This suggests no change in transformation mode. Further metallographic examination confirmed this observation. A martensitic transformation was obtained for similarly treated samples except that the surface was first electropolished. The Ms temperature was approximately 85°C below the plateau determined for the unpolished samples and cooling rates as slow as 2000°C per sec were adequate for producing marten-site. The transformation temperatures are in gen- / STRIP SAMPLE / COPPER I SAX/-/}' / CONNECTOR-----A f, SON|C poRTS AC LEADS 3j ]j"I rofe[ \ Mf/yinK/iKj''^ THERMOCOUPLE X-(^—iie"s*c? ' LEADS 1 INCH Fig. 1-—Schematic scction of gas quenching apparatus

Jan 1, 1970

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit? The rocks are well-consolidated Gila conglomerate, quartz , monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ransome.3 In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special, fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3 1/4x4 1/4-in. tool joints; 8-in. bits, 2 3/4x 3 3/4-in. tool joints; 6-in. bits, 2 1/4 x3 l/4 -in. tool joints; 4-in. bits, 1 5/8 x2 5/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property, To allow for 2 3/8-in. drill pipe with tool joints, 3 1/2-in. core barrels and bits were used. With the standard 3 1/2-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 5/8 to 3 7/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven-machines. The open churn drill hole was cased with 2 1/2-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in unconsolidated material like the formations drilled by

Jan 1, 1952

By G. E. Pellissier, P. H. Salmon Cox, B. G. Reisdorf

Banding that occurred in plates rolled from the early production heats of 18Ni(250) maraging steel is described and related to the segvegation of certain alloying elements (nickel, molybdenum, titanium), the extent of which was quantitatively evaluated by means of electron-microprobe analysis. The effect of banding on mechanical properties is discussed, with particular reference to observed directional differences in plane-strain fracture toughness of plates. It is shown that banding originates as interdendritic segvegation during ingot solidification and persists in some degree through normal soaking and hot reduction to plate. The results of the study showed that heating sections of small laboratory-cast ingots at 2200°F for 4 hr was sufficient to markedly reduce microsegregation and to considerably improve mechanical properties. Hot rolling of 7-in.-thick ingot sections to 1/2-in.-thick plate effected a similar reduction of microsegregation, but resulted in even greater increases in ductility and toughness than that obtained by homogenization treatment alone. DURING the past few years, considerable attention has been directed towards the low-carbon, high-alloy maraging steels and in particular towards the 18Ni-8Co-5Mo-0.4Ti alloy. The steels of this group, having an excellent combination of high strength and toughness, have a number of advantages over their more conventional medium-carbon low-alloy, quenched-and-tempered counterparts. In the annealed condition, the maraging steels are in the form of a ductile marten-site; aging at a relatively low temperature, typically 900°F for 3 hr, increases greatly the strength through the precipitation of intermetallic compounds. One problem in the early production heats of maraging steel was that the finished plate frequently displayed a banded structure. Previous work on other steels1-' had established that banding in wrought products is either a direct or an indirect consequence of chemical segregation, which occurs during solidification and persists to some extent through normal thermal and mechanical treatments. For example, Smith and others: in a study of low-alloy steel, were able to correlate the severity of banding in the wrought product with the degree of interdendritic segregation of nickel and chromium in the as-cast ingot. The effect of banding on the mechanical properties of steels is usually considered to be detrimental, although there is only limited evidence to suggest that a marked improvement in properties can be obtained with less heterogeneous structures. Comparison of the longitudinal and transverse tensile properties of banded and of homogenized 4340 steel showed that only the transverse ductility was improved by homogenization, but even then the improvement was not commercially significant.' Conversely, homogenization of through-the-thickness tension specimens of quenched-and-tempered steel plate, containing 1.47 pct Mn, increased the strength by as much as 10 pct and the tensile ductility by at least a factor of twos5 This improvement was related to the elimination of manganese-rich bands, which also are one of the factors responsible for cold cracking in the heat-affected zone of metal-arc welds.7 In the present study the nature and severity of banding in early commercial 18Ni(250) maraging steel plate and in laboratory-melted 18Ni(250) maraging steel plate was determined. The effects of banding on plane-strain fracture toughness and the effects of thermal homogenization treatments on the strength, tensile ductility, and toughness of 18Ni(250) maraging-steel as-cast ingots and rolled plate were evaluated. In addition, the effects of hot deformation by rolling on the mechanical properties of ingots were determined. 1) STUDIES OF BANDING IN EARLY PRODUCTION PLATE The chemical composition of the steel (A) used in this part of the investigation is shown in Table I. Banding was not clearly evident in either as-rolled or annealed* plate, but annealed and agedc** plate had a banded structure. The typical banded condition, Fig. 1, consists of layers of unetched austenite (white) and dark-etching martensite in a light-etching martensitic matrix. X-ray diffraction measurements showed that this steel contained more than 6 pct austenite. An electron-probe X-ray microanalyzer (using a focused beam of electrons) was used to determine the composition of the bands and of the material between the bands with respect to the main alloying elements— nickel, molybdenum, titanium, and cobalt. The recorded X-ray intensities were converted to concentration values with the use of a standard of similar composition. To facilitate probe positioning, all analyses were conducted on specimens that had been given a light etch. The influence of this etching on the analytical results was negligible; analyses made on the identical area before and after etching yielded essentially the same concentration values. The results of the electron-microprobe analyses at selected points revealed that the layers of austenite and adjacent dark-etching martensite contained greater amounts of nickel, molybdenum, and titanium than did the surrounding matrix, Table 11. The austenite layers

Jan 1, 1968

By Bhudeo N. Sinha, Paul Dean Proctor

Heavy metal contents in stream waters, sediments, and selected aquatic algae were determined for the upper Meramec River basin, Missouri, of 3905 km2 (1508 sq mi) area and site of the proposed and controversial Meramec dam and reservoir. Six distinct drainage areas within the basin are: (1) a lightly industrialized and farm area, (2) a primitive forested- ranch area, (3) an area which includes the Northern New Lead Belt, (4) the westward drainage of an old and extensive barite mining area, (5) the main trunk of the Meramec River, and (6) short north-divide tributaries of the Meramec River. Lower Paleozoic sediments rest nonconformably upon eroded and hilly Precambrian igneous basement. This locally rises as major inliers and also makes up the St. Francois Mountains to the east. Major lead, and lesser zinc, copper, cobalt, and nickel mineralization occurs in the buried Cambrian Bonneterre dolomite. Residual barite is present along the eastern fringe of the basin and is derived from the Potosi formation. Some 62 water samples, active stream sediments (AS), bank samples (BS), and 11 selected aquatic algae samples were collected in the various drainage areas and analyzed for copper, lead, zinc, cadmium, nickel, arsenic, and mercury contents. Heavy metals in water have a maximum range of 1-120 ppb (parts per billion), and this for zinc. The AS and BS sediments have orders of magnitude greater acid leachable metal contents in the -80 mesh fraction, with lead hawing the greatest range of 11-1028 ppm. Heavy metal content of stream-algae approaches that of the sediments in which they grow. Most anomalous heavy metal accumulations occur near mining and milling activities and in the streams draining such areas. Significant distortions of the primary dispersion pattern militate against geochemical exploration for hidden ore zones, but do demonstrate the mining, milling, and smelting activities of man, and sporadic mineral occurrences in younger horizons.

Jan 1, 1980

"The power development at these falls, three miles below the city of Great Falls, was made in 1891 by the original Great Falls Water Power & Townsite Company, and the Boston & Montana Consolidated Copper & Silver Mining company, the predecessor of the Boston & Montana Reduction Department mentioned above.The dam is 746 feet long, placed a short distance above the crest of the falls, and giving an effective head, as now constructed, of from 42 to 44 feet. There are power houses on both banks, those on the south bank belong to the Great Falls Power company, the successor of the Great Falls \!\Tater Power & Townsite Company, and the Great Falls Electric properties. The water is led from the dam to these power houses through sheet iron pen-stocks the water wheels are of the horizontal turbine type, and of various sizes.The water is here carried from the dam to the power houses by an open canal or headrace, the walls of which are concrete. This headrace is 100 feet wide at the widest point. The available head was originally less than 40 feet, but this was increased to about 44 feet by means of flashboards and tailrace wall, seperating the tailrace from the main river and delivering the water to the river at a considerable distance below the power house, thus taking advantage of a considerable fall in the river below the sheer fall at Black Eagle.A total of about 12,000 horse power 1s developed at these falls, the Great Falls Power Company, and Great Falls Electric properties developing about 2,000 horse power, and the Anaconda Copper Mining Company developing the balance."

Jan 1, 1913

By A. P. Pipilen, M. Weintraub, W. F. Hosford, A. A. 230-000-000-006 Orning

In a study of the principal factors affecting the transport of coal-water mixtures through a centrifugal pump and a pipeline, the interrelation between solids concentration, velocity, and pressure drop was established for a minus 2-in. bituminous lump coal in concentrations up to 48% by weight. Optimum concentrations were found to exist for maximum capacity of a given pipeline and for minimum energy requirements per ton of coal. Coal size degradation by particle fracture took place in the pump; abrasion and attrition to form fines took place in both pump and line. A novel system of studying flow of solid-liquid mixtures in pipelines by the determination of relative sound intensities was developed. The hydraulic transport of minerals is in part an established art and in part a relatively new field of industrial technology. The established art developed especially where the mineral was under water, where water was used in hydraulic mining, or where large quantities of water had to be pumped from the mining site to expose the mineral. Power requirements and limited life of pumps and pipelines, under such conditions, were relatively unimportant. Examples may be found in dredging, and in hydraulic mining and transportation of phosphate rock.' In the design of a coal pipeline the most needed information relates to flow characteristics, power requirements, pressure drop, size degradation, and size segregation as a function of solids-water ratio and size distribution of the mineral. A considerable amount of information has become available concerning pressure drop and energy requirements.2'3 These topics were therefore not studied intensively. Coal degradation, however, has not been clearly delineated. Lammers and coworkers4 showed that coal may be severely degraded in size but did not distinguish between degradation produced in the pump and in the line. It is the primary purpose of this paper to outline techniques used to acquire some of the much needed design data. A full report of the investigation is to be published by the Bureau of Mines at a later date. APPARATUS AND PROCEDURE The apparatus for circulation tests (hereafter referred to as Type III tests) consisted essentially of a loop and a centrifugal solids handling pump, with attendant instrumentation, and coal weighing and feeding equipment. It also included an adequate water supply, as shown in Fig. 1. The selection of 6-in., schedule 40, carbon steel pipe was based on the top size of coal to be used. Assuming that the top size of coal should not exceed 1/3 the inside diameter of the pipe, a 6-in. pipe would accommodate 2-in. coal, a realistic size for transport from the mine face. An 872-ft loop was constructed first. Later a few tests were made with a lengthened circuit of 1361 ft by superimposing an additional loop on the original one. All bends used were of 3-ft radius. A noisemeter microphone, taped to the pipe at various points, but generally about 50 ft downstream of the pump, was used to sense segregation of the coal and the length of slugs of coal in water. To measure the stream velocity, radioactive sources were encapsulated in plastic cubes. The specific gravity of the blocks was adjusted to 1.3 and 1.8 to simulate low ash and high ash coal particles. Their passage through the pipeline was detected by a Geiger counter. Because the repeated circuits of the Type III tests did not permit coal degradation in the line to be distinguished from that produced by the pump, the two

Jan 1, 1964

By J. G. Bouwkamp

This paper presents three general approaches towards the solution of the stress distribution and the behavior of tubular connections as used in offshore well drilling structures. First, the possibilities of using plastic models and photoelasticity techniques in evaluating the stress distribution in gusset plate connections are analyzed. The results of photoelastic studies on the stress distribution in the in-plane gusset plate of two-dimensional joints are presented. The influence of the configuration of the gusset plate (with and without cut-outs) is discussed. Second, the paper deals with recent developments and applications of computer programs to analyze connections with directly inter-welded tubes and with gusset plates. The possibilities and limitations of these programs are discussed. Stress patterns analyzed with these programs are presented for different joint configurations. Finally, the basic test procedures and results of a test on a tubular joint under static and alternating loads are discussed. INTRODUCTION The effective design of tubular connections as encountered in offshore well drilling towers or floating platforms has been complicated basically by the radial flexibility of the tube walls. This flexibility is a source of severe stress concentrations which can initiate an early failure of these joints. In an attempt to reduce the influence of the wall flexibility of the column tube, certain joints are presently designed by inter-welding the incoming branch members. In those designs, the force acting normal to the chord tube can be reduced considerably. A second group of joints incorporate gusset plates or stiffening rings to stiffen the column wall and to distribute the incoming branch member forces over a larger part of this wall. A third approach to improve the stress distribution in a tubular joint is to increase the wall thickness of the column member. This can be achieved by simply applying a thicker wall section in the vicinity of the joint. A fourth possibility to restrain the radial flexibility of the tube wall is to fill the column member with concrete. Also, a single, cast steel seat welded to the column tube can be used to improve the stress distribution in this wall. Although all these designs improve, in general, the state of stress in the column wall, the altered stiffness often causes the development of critically stressed areas in the web members. At the same time the actual design in most instances is decisively influenced by the site which governs the depth and controls the forces produced by waves, earthquakes and ice flow. Also, the towing, erection and foundation requirements of offshore structures can affect the actual design selection. Because of the complexity of the structural configuration of tubular joints, the stress analysis of these connections has necessarily been based on simplified and often crude assumptions. For the earlier and smaller type of connections with about 4-ft diameter column sections, the primary problem was to evaluate the relative stiffness of the column wall section and the load transfer between joint members. Due to the recent developments of offshore drilling structures with increasingly larger connections (e.g., column diameter. 32 ft; web members, 8.5 ft) this problem has become even more critical. One design philosophy for such large joints follows a member-to-member connection with radially heavy reinforced column sections. This radial stiffness can be attained by closely spaced and intensively stiffened horizontal diaphrams together with vertical stiffeners. A second solution incorporates a concrete-filled section between the outer and inner walls of the column tube. Another philosophy considers large gusset-plated joints. The problem in these joints is to develop an effective load transfer between the branch tubes and the gusset plate and to minimize the stress concentrations in the member walls as effectively as possible. Several concepts are followed to achieve this gradual transfer between web-member walls and gusset plates. Because the number of joints in these huge platforms is limited compared to the over-all size, a proper design of these joints is even more important than was the case for the many joints in the smaller, but multi-legged towers. A failure of one of those ultra-large joints could well cause the complete collapse of such a structure. Under these circumstances an accurate analysis of the large joints is of the greatest importance, together with information regarding the expected behavior of such joints under critical alternating load conditions. Recent applications of photoelastic model techniques have proved to be quite effective in evaluating the elastic behavior of such joints. Although a complete study of such connections is quite well possible with present-day photoelastic techniques, it might often be feasible and necessary to limit the objectives and to restrict these investigations to the study of a specific aspect of the joint. Another very promising avenue of approach to solve the complex stress pattern in these connections seems to be the recent development of digital computer programs. In this category, cylindrical shell programs and finite element methods for more complex configurations have

Jan 1, 1967

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By Ronald W. Utley

INTRODUCTION The ''Do's and Don'ts" of installing equipment in a comminution circuit begin during the study stage of a proposed project, continue through preliminary engineering, detail engineering, procurement, the actual placement of equipment at the job site, and end with turnover to the owner. Equipment supplied for a modern comminution circuit will be high quality, rugged machinery designed according to appropriate manufacturing standards for long hours of trouble-free service. However, certain precautions and procedures must be observed in plant design and layout, equipment handling, installing and servicing in order to obtain optimum performance. This chapter contains general installation "DO'S and Don'ts" for the major equipment in the circuit. •Primary Gyratory Crushers •Rock Breakers (Hammer) •Belt Conveyors •Apron Feeders •Weigh Belt Scales •Secondary Crushers •Vibrating Screens •Grinding Mills •Mill Liners •Open Gear Sets •Speed Reducers •Electric Motors •Cyclones •Slurry Pumps Some questions will not be covered in this chapter, or may not be applicable to the actual equipment purchased, as requirements do vary from manufacturer to manufacturer. Additional specific information can be obtained by contacting the manufacturer's local representative or the factory. All inquiries should be accompanied by the following information: •Unit size and type of equipment •Manufacturer's shop order number (after order placement) •Serial number (after manufacture) DO'S 8 DON'TS FOR INSTALLATION OF ALL COMMINUTION CIRCUIT EQUIPMENT Installation By Design DO obtain tables of weights and clearances from manufacturer. DO obtain WR2 forces from manufacturer to determine that the foundation is adequate. DO determine compression strength of foundation soil and/or rock. DO obtain manufacturer's recommended typical foundation drawings. If substantial alteration to manufacturer's drawings is required, check with the manufacturer before proceeding.

Jan 1, 1982

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-'Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967