Search Documents

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Yutaka Saito

"Effect of moisture content must be fully understood for controlling the granule compaction of ceramics. It changes the mechanical behavior of spray-dried granules applied for compaction process, and governs the structure and properties of .ceramics. To understand the time-dependent change in processing, the kinetics was examined for change of moisture content for granules placed in a die and the pressed compacts also. The results were explained in terms of apparent moisture diffusion coefficients. They varied non-linearly with the PVA content in the granules. The results were explained through the non-uniform PVA distribution in the granules.IntroductionMoisture must be controlled in compaction process to produce the green compacts having uniform structure. It affects glass transition temperature of binder and thus the deformation behavior of powder granules under an applied stress. Several studies [1-7] have clarified the effect of moisture content on the compaction behavior of granules and the structure of resultant compacts for both die pressing and cold isostatic pressing (CIP) of pre-formed compacts. In these studies, the moisture contents in the system were equilibrated with the humidity in the atmosphere before compaction. In practice, however, the moisture content in the system may vary with time if the relative humidity of surrounding atmosphere is different from what the granules were equilibrated previously. This is very likely case in real production processes. However, the kinetics of moisture change in the granules as well as in the pre-formed powder compacts have not been well studied. For controlling the microstructure in a system, it is necessary to fully understand the kinetics of moisture change and its relevance to packing structure of powders."

Jan 1, 2000

By J. W. Dini

Introduction The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. MFD is .a large diversified service organization including approximately 400 full time employees. The group provides a wide variety of processes including all common machining and fabrications operations, laser and water jet cutting, electrical discharge machining, lapping, electron beam and laser welding, vacuum brazing, heat treating, forming, electroplating and metal finishing, optical polishing and grinding, vacuum coating, vacuum engineering and a variety of plastics operations. These operations occupy more than 1,250,000 square feet of floor space. For more detail on the many fabrication related services available from MFD, see Reference 1.

Jan 1, 1992

By S. Redik, C. Wenzl, D. Gregurek, A. Spanring

Zinc is a component of many input materials used in various pyrometallurgical processes, for example primary lead and zinc production from Pb/Zn ores and recycling processes dealing with zinc-containing residues (e.g., copper recycling, WAELZ process). Hence, zinc and its compounds are present in the respective metallurgical vessels and interact with the refractory lining. In the present work the zinc attack on the refractories out of various primary and secondary furnaces is briefly introduced and discussed. At the prevailing processing temperatures in the metallurgical vessels, zinc oxide is highly corrosive for the brick components. The knowledge of the wear behavior is based not only on a detailed chemical and mineralogical characterization carried out on provided post mortem samples, but also on FactSage calculations. This together with results obtained by practical testing in the RHI pilot plant represents an important prerequisite for product development and brick selection for the individual customer application.

Jan 1, 2016

By J. Winters, L. Vos, C. Canoo

Committed to a sustainable development of zinc applications, Union Miniere is investigating processes for the minimisation of waste and residues originating from the classic hydrometallurgical zinc process. In that context, Union Miniere has developed a method for the cold inertisation and solidification of goethite, the Graveliet® process. The result is a hard and inert gravel that can be used in the building industry. During the past two years, a pilot plant for the production of Graveliet® has been built and operated. In the present paper, the Graveliet® process and the pilot plant are described after which the properties of the produced gravel are discussed, from both a mechanical and an environmental point-of-view. Graveliet fulfils the criteria for use as a secondary building material. The GravelietJ process is a viable technology to avoid stockpiling of goethite residues and it thus assures the long-term development of the hydrometallurgical zinc process.

Jan 1, 2000

By R. K. Hill

The Hidalgo Smelter successfully reduced operating costs by 25% compared to the previous two years through a focused holistic approach to development of its entire workforce. The first phase involved basic team training skills for natural work teams. The second phase provided leadership training via breakthrough education to 40 of the smelter leader-both hourly and salaried. The third phase stretched out the teams training to include rewards for performance that resulted in hourly teams converting to salaried status-part of a company wide initiative. The fourth phase saw 1998 become the "Year of Safe Cost Reduction" where 7 breakthrough projects focused on different areas of expenditure. Implementation of lean manufacturing as a tool for teams to truly get their arms around what they controlled, introduced accountability and responsibility for operating results at the team level. This will allow the release of experienced supervisors from this role, to a pool of technical expertise, where our future breakthroughs will be designed and implemented.

Jan 1, 1999

By Kamal Adham

Hydrochloric acid is used as lixiviant in such hydrometallurgy processes as synthetic rutile production and nickel extraction. The intermediary metal chloride is normally roasted to release gaseous HCl and a solid metal oxide. A large amount of fuel is required for this thermal regeneration, mainly to vaporize the water content of the feed solution. To conserve fuel, some energy recovery from the off-gas is currently achieved, but the fuel costs can further be reduced by process optimization and energy recovery from the gaseous, aqueous and solid products of the regenerator. Here, first the existing limitations to fuel efficiency in the industrial scale HCl regeneration roasters are described. Then, for the case of a dilute feed solution, options for pre-evaporation and fuel minimization are modeled and compared. Finally, energy recovery technologies including heat pumps, acid heat exchangers and solid waste heat boilers are described, and their potentials as the heat source for pre-evaporation of the feed are evaluated.

Jan 1, 2003

By Ian M. Ritchie

Right across the universities of the developed world, the traditional disciplines of physics and chemistry are losing ground. Extractive metallurgy, which depends so heavily on chemistry, is also contracting despite a clear need for people with this kind of training in the mining industry. Reasons for this loss of popularity are discussed in this paper. High on the list is one of image. The extraction of metals is widely seen as a dirty, polluting, sunset industry which involves working in remote and uncomfortable corners of the earth for inadequate compensation. Ways in which the image problem can be overcome are considered. It is concluded that a concerted effort needs to be made by the universities and industry to redress this situation. The importance of extractive metallurgy, both now and in the future, when a greater emphasis will be placed on sustainability and recycling, needs to be stressed. In addition, courses need to incorporate training for a career path that leads on beyond extractive metallurgy.

Jan 1, 2003

By C. R. Bennett

The first phase in the design, development and implementation of a comprehensive computational model of a copper stockpile leach process is presented. The model accounts for transport phenomena through the stockpile, reaction kinetics for the important mineral species, oxygen and bacterial effects on the leach reactions, plus heat, energy and acid balances for the overall leach process. The paper describes the formulation of the leach process model and its implementation in PHYSICA+, a computational fluid dynamic (CFD) software environment. The model draws on a number of phenomena to represent the competing physical and chemical features active in the process model. The phenomena are essentially represented by a three-phase (solid-liquid-gas) multi-component transport system; novel algorithms and procedures are required to solve the model equations, including a methodology for dealing with multiple chemical species with different reaction rates in ore represented by multiple particle size fractions. Some initial validation results and application simulations are shown to illustrate the potential of the model.

Jan 1, 2003

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Roberto Parra, Roberto Parada

"A novel process for minor elements control in copper pyrometallurgical production is proposed based on a theoretical analysis and the results of an experimental program. Its application can solves operational problems related to volatile elements that determine pollutants gas emissions and the final quality of anodes. The process considers a calcination of mixtures of the dust with sulfidizing agents such as dirty copper concentrate or elemental sulfur at temperature under 800 °C. The product are a clean calcine that recovers all the Cu content on the dust and a gas stream that collect the minor elements as sulfides species. The calcine can be returned to the smelter avoiding the As increasing in the circuit and so on, the capacity for the treatment of dirty concentrates for the smelter can be higher. The possibility to apply vacuum in the calcinations step can decrease the operation temperature. The solid condensed from the gas has different options for its stabilization, with the advantage that this stream represents few mass with high As content.IntroductionThe control of undesired minor elements (IVIES) in conventional pyrometallurgical copper production is especially relevant for ore deposits associated to Andes region. The concentrates that are being produced present every time higher levels of volatiles and harmful elements: group Va (As, Sb and Bi), Pb, Zn, and Sn."

Jan 1, 2008

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By N. El-Kaddah, V. L. Acoff, M. Arenas

"Control of the weld penetration, weld pool shape and temperature field in arc welding is critical to achieve the desired microstructure and mechanical properties in the resultant welds. This is particularly important in welding gamma titanium aluminides (y-TiAl) where the weld pool is relatively shallow and the temperature gradient in the heat-affected zone is quite steep. This paper investigates theoretically and experimentally the evolution of the shape of the weld pool for stationary gas tungsten arc welds in y-TiAl alloys. A mathematical model has been developed for predicting the electric current flow, the resultant electromagnetic forces in the metal, and the transient development of the temperature and velocity fields in the molten pool generated by a spatially variable heat flux at the arc-striking zone. The governing equations were solved numerically using the control volume technique. Welding experiments were carried out to determine the shape of the weld pool and the extent of the heat affected zone at different welding times for model validation. The numerical predictions were found to be in reasonable agreement with measurements. It is suggested that the model presented in this paper is likely to provide the information needed for predicting the microstructure and mechanical properties of y-TiAl welds. IntroductionIn recent years, there has been considerable interest in the welding of gamma titanium aluminides as a means of manufacturing high-temperature, high-performance components for turbine and automobile engines. These alloys are highly reactive, and must be welded in vacuum or inert gas atmosphere, rendering electron beam, and inert gas tungsten arc welding (GTA) to be the only suitable welding techniques for joining these materials [1-3]. The GTA welding is especially attractive because of its flexibility and relative cost-effectiveness. However, previous studies on the weldability and weld properties of these alloys using this process revealed a decrease in the mechanical properties in the fusion zone [4]. This is generally attributed to the change of the original duplex structure to a dendritic structure amplified by the shallowness of weld spot. Quantifying the effect of arc operating parameters on the geometry and temperature profile of the welding pool prior cooling is the first step for controlling the fusion zone microstructure and mechanical properties."

Jan 1, 1999

By Viktor Mukhin

"Among the methods proposed for spent activated carbon regeneration, the most acceptable is, thermal reactivation, because in this case the existing equipment for manufacture of activated carbon can be adapted for this purpose.In order to conduct the process of thermal re-activation of spent activated carbon directly at gold mills, a fullscale drum-type furnace with external electric heating has been developed, i.e. EPV-300 model with a throughput rate of 50 to 120 kg/hour. Its use ensures restoration of the adsorption properties of carbon up to the level of fresh activated carbon with an insignificant (by 0.7%) decrease in strength and with a high (95% to 97%) yield of reactivated carbon.During the recent years, activated powder carbon has been extensively used in flotation processes for treating polymetallic ores at ore treating plants to improve recoveries of main metals (copper, lead, nickel, etc.).Especially large volumes of activated powder carbon are used at the Talnakh concentrator of the Norilsk Mining and Metallurgical Complex in Russia for absorption of residual flotation reagents from recycled water in order to ensure efficient selective separation of minerals with similar physical and chemical properties.IntroductionSorption technology based on active carbons use starts being applied in such an important in the widest sense of the word strategical branch of economics as non-ferrous metallurgy. Thus since the middle ninetieth Russian gold extraction industry began to apply widely the processes of sorption from pulps and solutions by means of high-resistant granulated active carbons. That provided the start of gold ore minefield exploration, increasing of gold extraction from the ore and reducing its loss with the ""tails"" of process. At present more than 40% of Russian gold is extracted with the help of sorption technologies [1].Another field of active carbons application in non-ferrous metallurgy is the processes of non-ferrous ores floatation at ore-mining and processing enterprise. For that purpose powdered (less than l00µm) active carbons are used for providing the effective selection of minerals with similar physicochemical properties. This method not only increases the metal extraction level but provides deeper division of them."

Jan 1, 2008

By Dominic T. Jordan, Quinn G. Reynolds, Christopher J. Hockaday, Ian J. Barker

A direct-current (DC) plasma arc furnace is a type of electric furnace used for metallurgical operations. The successful operation of DC furnaces depends to a large extent on gaining a fundamental understanding of the arc phenomenon itself, and ensuring its presence in the furnace at all times. A method for detection of the presence of the arc in a DC circuit is presented, along with discussion of why this may be of value for certain modes of furnace operation such as brush-arc. The theoretical development of the method is presented along with supporting experimental work conducted on large-scale pilot-plant facilities.

Jan 1, 2014

By Douglas M. Matson, Rongbiao Gu, Christopher San Marchi, Anil Saigal

"Hydrogen embrittles most structural metals, although the form and magnitude of embrittlement depends on the source of the hydrogen as well as the stress in the metal. Hydrogen fuel cell systems typically store gaseous hydrogen fuel at high-pressure, which provides both a source of hydrogen and high stresses in the containment materials. Understanding and measuring the effects of hydrogen on the mechanical properties of common structural metals, especially fatigue properties, is important for safe, long-term operation of such systems. This work explores the use of thermography to efficiently and quantitatively evaluate hydrogen-assisted fatigue of type 304 austenitic stainless steel. In particular, thermographic analysis was used with rotating-beam fatigue testing and shown to provide repeatable results which are in general independent of test cycle frequency while reducing test times by several orders of magnitude. The effects of hydrogen were studied by thermally precharging fatigue test specimens in gaseous hydrogen prior to thermography-assisted fatigue testing and then compared to testing of non-charged specimens. Hydrogen-precharging increased the strength of this type 304 austenitic stainless steel and increased the fatigue life by a factor of about 50-100.IntroductionThe world is facing a severe energy and environmental challenge: how to provide competitive and clean energy for its citizens in light of an escalating global energy demand and concerns over energy supply security, climate change and local air pollution. As a carbon-free energy carrier, hydrogen provides a promising vector for storing and distributing renewable energy. Hydrogen is an important industrial gas that is used extensively in many industries. However, with growing demand for clean energy, hydrogen fuel cell systems are being developed for use in consumer products, such as fuel cell vehicles, which changes the landscape for safe design of high-pressure gaseous hydrogen systems."

Jan 1, 2012

By P. V. Ananthapadmanabhan

Feedstock powders of metals, alloys and ceramics for thermal spray applications have to meet several specifications. Particle shape, size and distribution, powder flow characteristics and density are the important factors that need to be controlled, in order to ensure high spray efficiency and better coating properties. Thermal plasma technology can be effectively utilized to produce metal, alloy and ceramic powders for spray applications. The present paper describes plasma spheroidisation of commercially available aluminium powder and nickel-aluminium powder blend in a plasma reactor. Results show that the processed powder particles bear spherical morphology with excellent flow characteristics, which make them ideal for thermal spray applications.

Jan 1, 1997

By Barry T. Kilbourn

There is a continuous quest for better-performing materials, for example, to withstand higher temperatures, to resist more efficiently degradation or to be electrically conductive under extreme conditions. The oxides, and similar compounds, of the lanthanides and yttrium can, in some cases, help provide such behavior. Other advanced materials, such as hydrocarbon catalysts, optical ceramics or sensitive phosphors, may also require these oxides for some essential function. The role of the oxides in a wide variety of technologies, some novel and developing, will be reviewed and the underlying physico-chemical principles, the common threads, between several less well-known and apparently unrelated uses discussed.

Jan 1, 1989

By Ali Unal, Ali I. Kahveci

Alcoa developed a fractional crystallization process some 30 years ago as a method to purify aluminum. Depending on the purity of feed metal, it has been commercially used to make 3N7-6N purity aluminum. As an extension of this technology, Alcoa has experimented with purifying various aluminum alloy scrap for the purpose of recycling. Purified aluminum alloy scrap can be reused for making the same alloy. This presentation will discuss Alcoa fractional crystallization technology and its application to alloy scrap processing. Process capabilities and the partitioning of eutectic and peritectic impurities during fractional crystallization will be discussed for the alloy systems investigated.

Jan 1, 2000

By Neil E. Izatt

The use of Molecular Recognition Technology (MRT), a selective separations technology using specifically designed ligands, has been established as an effective process for removal of metal ions found in many hydrometallurgical, chemical, and wastewater streams. The MRT process has been proven to be highly efficient and effective for indium extraction and recovery from zinc acid leach, electrolyte, chemical process and waste streams. A high percentage of the indium is recovered in a solid product format. MRT has also proven effective for germanium extraction and recovery from similar feed streams. This paper provides the indium and germanium metal recovery flow sheets and analytical results of the metal load and recovery steps.

Jan 1, 2006

By C. T. Yavuz

Higher environmental standards have made the removal of arsenic from water an important problem for environmental engineering. Iron oxide is a particularly interesting sorbent to consider for this application. Its magnetic properties allow relatively routine dispersal and recovery of the adsorbent into and from groundwater or industrial processing facilities; in addition, iron oxide has strong and specific interactions with both As(III) and As(V). Finally, this material can be produced with nanoscale dimensions which enhance both its capacity and removal. The objective of this study was to evaluate the potential arsenic adsorption by nanoscale iron oxides, specifically magnetite (Fe3O4) nanoparticles. We focused on the effect of magnetite particle size on the adsorption and desorption behavior of As(III) and As(V). The results show that the nanoparticle size has a dramatic effect on the adsorption and desorption of arsenic. As particle size is decreased from 300 nm to 12 nm the adsorption capacities for both As(III) and As(V) increase nearly 1000 times. Interestingly, this increase is more than expected from simple considerations of surface area and suggest that nanoscale iron oxide materials sorb arsenic through different means than bulk systems. The desorption process however, exhibits some hysteresis with the effect becoming more pronounced with small nanoparticles. This hysteresis most likely results from a higher arsenic affinity for magnetite nanoparticles. This work suggests that magnetite nanocrystals and magnetic separations offer a promising method for arsenic removal.

Jan 1, 2006