Search Documents

By Fjeldstad Karin Jusnes

Two quartz types used in the silicon and ferrosilicon industry were heated to temperatures of 1600 and 1700 °C. The parameters varied were the temperature and the holding time at maximum temperature. The amount of quartz, cristobalite and intermediate amorphous phase were measured using XRD and the internal standard method. Type P showed a much larger ability to transform to cristobalite at lower temperatures than type A. Type P had a larger amount of alkali and alkaline earth impurities. This could have enhanced the transformation to cristobalite. For quartz type A the amount of cristobalite was larger at 1600 °C than 1700 °C. This can also be seen for some of the samples of type P at shorter holding times.

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By Merete Tangstad, Fei Li

This paper studies the quartz and carbon black pellets at elevated temperature with varying temperature and gas atmosphere. High-purity quartz and commercial ultra-pure carbon black was mixed (carbon content wt.15%), and then pelletized into particles of 1-3mm in diameter. The stoichiometric analysis of the pellet during heating is studied in thermogravimetric analysis (TGA) furnace at different temperature in CO and Ar atmosphere. The microstructure, phase changes and element content of sample before/after heating is characterized by X-ray diffraction, scanning electron microscope, X-ray fluorescence and LECO analyzer. The reaction process can be divided into two stages. Higher temperature and argon atmosphere are the positive parameters for SiC formation.

Jan 1, 2016

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

By N. Kanari

The thermal decomposition studies of two zinc basic carbonate samples were carried out up to 400 "C by thermogravimetric analysis, boat experiments and differential scanning calorimetry measurements 'DSC'. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy, x-ray diffraction and laser particle size analyzer. The thermal decomposition of both samples started at about 150 "C and the rate of decomposition became significant at temperatures higher than 200 "C. The apparent activation energies 'Ea' in the temperature range 150-240 "C for sample decomposition were between 132 and 153 kJ1mole depending on the sample origin. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 "C suggest that the decomposition reaction probably occur in a single step.

Jan 1, 2002

By B. Q. Li, Y. Shu, K Lynn

"This paper discusses the effects of magnetic field and internal radiation on the melt flow and solidification morphology during solidification processing of oxide crystals for optoelectronic and remote sensing applications. The numerical solution of the integral differential equation characterizing the internal radiation and the magnetohydrodynamic equations describing the magnetic and transport phenomena is obtained by applying the combined discontinuous and continuous finite element method. The results show that both internal radiation and an externally applied magnetic field can have important effects on the melt flow and solidification behavior during the melt processing of oxide materials.IntroductionOptical single crystals are widely used in optical and electronic devices. These crystals are often grown from high temperature oxide melts under strictly controlled conditions. As in the well-known single crystal growth processes for semiconductor wafers, thermal gradient in the melt is a major contributing fuctor to the oxide melt pool. Unlike the semiconductor single crystal growth processes, however, the oxide melt is semitransparent and internal thermal radiation plays an important role in redistributing the thermal energy in the melt pool. Our recent experience with pilot-scale plant measurements also shows that the oxide melt is electrically conducting, although its electrical conductivity is considered much lower than the liquid metal or semiconductor melt.The fact that the oxide melt is absorbing and emitting in the thermal radiation frequency range makes it difficult to study the thermal energy transport in the melt pool. This is because thermal radiation is governed by a hyperbolic differential equation, which is different from those describing the transport processes in liquids. Also, our understanding of how thermal radiation interacts with other transport mechanisms such as convection and conduction is rather limited at point in time, in particular in high temperature oxide melts for optical single crystal processing."

Jan 1, 2004

By Emmanuel N. Zevgolis

In the present work, a reduction roasting experimental study of Greek nickeliferous laterite samples with a gaseous reducing mixture ? CO:N2- is presented. The effect of parameters such as temperature, ore grain size, and composition of the reducing mixture were examined. It is deduced that the reducibility of intermediate type laterite sample, where iron appears mainly in the form of goethite (a-FeOOH), is considerably higher than that of limonitic type laterite samples, where hematite (a-Fe2O3) is the predominant iron mineral phase. The degree of reduction of the limonitic type laterite samples does not exceed 50%, while it reaches 95% in the case of the intermediate-type laterite sample under the same experimental conditions. Increasing the temperature in the range 750-900°C does not considerably favor the reduction of the limonitic type laterites, whereas decrease of ore grain size of the limonitic-type ore samples and more intense reducing conditions increase the reduction. The considerably higher specific surface area values of the intermediate laterite samples, diminishes the effect of the ore grain size and this can be regarded as the critical parameter leading to the higher reducibility of this ore.

Jan 1, 2009

By Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping, Zhai Dacheng

"Corrosion resistance of RE-Ni-W-P-SiC composite coating and 3 l6L stainless steel in corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations by means of immersion methods and anodic polarization curves obtained by DHZ-1 electrochemical synthetic tester and HDV-7 transistor constant potentiometer. Immersion experiment results show that corrosion rate of RE-Ni-W-P-SiC composite coating as-deposited in HCl solutions increases with the rise of HCl concentrations, on the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing the HCl concentrations the corrosion rates of the coatings as-deposited and after heat treatment in H2SO4 and H3PO4 solutions respectively decrease with the rise.of H2SO4 and H3PO4 concentrations the corrosion rate of the deposit as-deposited in FeC13 solutions decreases with increasing FeC13 concentrations, while the rate of the composite coating after heat treatment increases .with the rise of FeC13 concentrations.In addition, the corrosion rate of 3 l 6L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations increases with rising of concentrations. Furthermore, the corrosion rate of 316L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions respectively is much greater than that of the RE-Ni-W-P-SiC composite coating as-deposited and after heat treatment in the same corrosion media.1. IntroductionAll the materials and their products, when processed, stored and used, it is inevitable that the corrosion, wear, fatigue and crack occur owing to the actions of surroundings. Those early failure and abrasion, through all kinds of departments and profession that corrosion consumes one percent of tens of the steel products of the whole world; and two or four percent of the GDP is lost because of the corrosion."

Jan 1, 2000

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By Patrick R. Taylor

Sub-micron sized boron carbide powders have been synthesized in a non-transferred arc thermal plasma reactor. Precursors for this synthesis are boric acid or boron oxide powders and methane. The powders produced were characterized in terms of size, shape and purity. Methods to increase the purity of the product were evaluated and included hot water leaching to remove unreacted oxides and controlled temperature, air roasting to remove excess carbon. Theoretical results are also presented on the thermodynamics and mechanisms of the synthesis reactions.

Jan 1, 1994

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Jian Yang, Hinmi Zheng

"The mode of occurrence of sulfur and mercury in 57 Chinese bituminous coals have been examined using X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), and Zeeman atomic absorption mercury spectrometer. Mercury levels in coal are related to the geographic location of the coals and types of the coals. A synthesis of result indicated that most likely occurrence modes of mercury in high-sulfur and high-mercury coals are in solid solution in pyrite. Our study from 57 coal samples showed that most values of mercury concentration in coal varied from 100 to 1000 ng/g with an average of approximately 500ng/g, and mathematical model about correlation between mercury and sulfur was gained by mathematical statistics. This is apparent that mercury and sulfur vary concomitantly from coal data (table 3) , the high correlation between them in all coals at confidence of 95% ( a=0.05 ) .1. INTRODUCTIONThere contained about one trillion ton abundant coal resources in China. As a leading level of proven coal reserves in the world, the coals mainly distributed in north China and northwest China, especially in Shanxi, Guizhou, Shanxi provinces and Inner-Mongolia autonomous region. At the same time, China has the largest production and consumption of coal, and has the output of coal nearly accounted for 37 percent of the world's production. Coal-fired power plants are the major source of energy generation in China, and the proportion of coal combustion is up to 75 percent in the total energy configuration. Therefore, the mercury pollution caused by coal-fired has become a topic of wide-spread discussions since 1990. The contamination of mercury of human activities accounted for 10 to 30 percent [1], and the mercury emissions of coal-fired flue gas has made the greatest contribution to the pollution of atmosphere[2] In the past 30 years, the global increasing concentration of mercury pollutant in atmosphere maybe result from coal combustion[2]. The mercury emissions caused by coal-burning has become the main reason of China's mercury pollution, and the characteristics of mercury pollution is closely related to China's energy configuration, additionally, the features of mercury pollution have changed from the point pollution in 1970's to diffused pollution today[3]. Mercury can be found in various types of coals, and it is evaporated into gas phase during the combustion process."

Jan 1, 2011

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

By Juan Hernández Ávila

This work studies the Molybdenum effect on the microestructure, mechanical properties of an as-cast ductile iron. For this study five ductile irons with different amounts of Molybdenum each were made in an induction furnace. In this material nodule count and nodularity is affected by the Molybdenum additions; The iron´s matrix, nodules and the phase were analyzed using scanning electron microscopy detecting Molybdenum only in the matrix. Mechanical properties such as hardness, microhardness, tensile strength and yield strength show increments as the Molybdenum amount is increased. In the same way, ferrite and pearlite phases display a variation in their percentage as the contents of the alloy element increase. This element has a marked influence on the pearlite interlaminar spacing. From the obtained results we conclude that Molybdenum in these quantities dissolves in solid ferrite solution during the solidification process, improving the material´s mechanical properties.

Jan 1, 2009

By Signe Kjelstrup, Leiv Kolbeinsen, Marit Takla, Odne Burheim

"This paper presents a Seebeck-type solid state thermoelectric power generator unit, designed to investigate the possible recovery of radiant waste heat at a silicon plant in Norway where roughly 703 of the total input energy leaves the process as waste heat. The unit is 0.5 m x 0.5 m and is built of 36 commercially available thermoelectric devices based on bismuth telluride p - and n - type semiconductors. Thermoelectric devices directly convert fractions of a heat flux into an electric current (and vice versa) and may therefore be convenient for recovery of waste heat when the heat source is discontinuously available. The purpose of the thermoelectric unit is to give a proof of principle of direct thermoelectric energy conversion on a large scale. We present the initial test results for the generator. At an average temperature difference between the heat reservoir and the heat sink of 98°C, we measured an open ciruit potential of 23.44 ± 0.06 V and the matched load power output was 39.4 W. At a temperature difference of 220°C, we predict the generator open circuit potential to be 40.8 V, which corresponds to an efficient Seebeck coefficient of 242 µV /K, and matched load power output to be 120 W.IntroductionThe world's power demand increases, driven by population growth and increase in living standards and simultaneously global warming is recognized as one of our most serious environmental problems. According to the International Energy Agency[l], the industrial sector accounted for approximately one third of the total global power consumption in 2005. Increasing the energy efficiency of industrial processes thus represents a benign and substantial route for addressing environmental concerns and energy security.In accordance with the second law of thermodynamics, all real processes are associated with lost work which is energy being dissipated as heat to the surroundings[2]. Improving the energy efficiency of industrial processes is about finding the process path associated with a minimum of lost work. The more evenly the losses are distributed, the smaller are the losses [3, 4]. In addition, exploiting the unavoidable waste heat will contribute to improve the energy efficiency. The waste heat may be utilized for heating purposes and/or it can be upgraded to work for instance via some sort of heat engine."

Jan 1, 2012

By Chan. C. L., Zehr. R., M. M. Chen, J. Mazumder

"Two three-dimensional models of a surface tension gradient driven flow during laser surface heating are developed. The first model is based on a perturbation solution. The basic solution corresponds to the stationary axisynwnetric case and perturbation is based on a small scanning velocity. The advantage of seeking a perturbation solution, as it turns out, is that the three-dimensional flow is modeled by two sets of two-dimensional equations which are presumably much more tractable than the original three-dimensional equations. Numerical solutions are obtained and discussed. The second model is a full three-dimensional numerical solution of the Navier-Stokes equations, using a point-by-point partially vectorized iteration scheme. Surface shape is also determined in a self-consistent manner. The effect of the presence of convection on pool geometry, cooling rate and solute redistribution is presented and discussed.IntroductionThe existence of fluid flow and convection and their effects were first reported in the fifties (1,2). The role of convection in controlling pool geometry such as pool shape, undercut and ripples, and defects such as variable penetration, porosity and lack of fusion and weld properties such as weld homogeneity and bead formation is studied by a number of researchers and is reviewed by the authors in a recent paper (3).Recently, surface tension gradient driven flow has been identified as one of the forces responsible for convection within the molten pool (4,5). It is postulated that surface tension gradient driven flow is responsible for the surface ripple formation in the weld pool (6-8). Oreper, et al. (9) developed a two-dimensional convection model. Buoyancy, electromagnetic and surface tension gradient forces were considered. The formulation was based on a specified pool profile. It was found that the surface tension gradient is the dominant force in most cases. However, the solid-liquid interface is not known a priori. In fact, the solid-liquid interface, i.e. the pool shape, is a piece of information that the model should be able to predict. A two-dimensional transient self-consistent (i.e. the solid-liquid interface is solved as part of the solution] model for laser surface melted pool was first developed by Chan, Mazumder, and Chen (3)). This model predicted a non-uniform cooling rate, hence non-uniform microstructure. Depending on the Prandtl number (i.e. material) and surface tension number, the shape of the molten region as well as the cooling rate changes. It was also predicted that the recirculating velocity is of one or two order of magnitude higher than that of the scanning velocity. This model provides the detail of the flow field and heat transfer on a plane perpendicular to the scanning direction. However, the front-to-back motion and its effect on heat transfer also play important roles in the physical process, especially for the fact that the recirculating velocity is so much higher than the scanning velocity. Such a motion cannot be obtained from two-dimensional models."

Jan 1, 1986

By Qiang Zhong, Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

The occurrence of different ringing behaviors in oxidized pellet kiln for two kinds of coal (A and B) with similar properties, is difficult to explain based on the relationship between kiln ringing and coal properties. In this paper, the interaction of coal ash with pellet scrap powder was considered by studying the cohering behavior of powders consisting of them. The results showed that the cohering briquette strength of pellet scrap powder increased considerably when mixed with a small amount of coal ash; a maximum could be reached when the mass percent ratio of coal ash was 1.5%; the strength of powder mixed with coal B ash was always higher in same firing system. This obviously illustrated that coal B caused a more serious ringing problem. The relevant mechanism was that the stronger reactivity of coal B ash made cohering briquette have a more perfect crystallization and a more compact structure.

Jan 1, 2015

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By Rolf R. von Oppenfeld

Onsite hazardous waste processors often find obtaining a Treatment Storage and Disposal (TSD) permit one of their first major challenges. Some processors may spend the time and money required by the permitting process, only to find out later that a permit was not necessary. This paper will present and analyze four strategies that processors may use to avoid obtaining a TSD permit. Some facilities will be able to remove their waste streams from RCRA's oversight by ensuring the material is not "hazardous" waste. Parties that treat waste while it is in process may be able to avoid generating "waste" altogether. Certain treatment facilities have been specifically exempted by EPA. Finally, treatment of waste while it is in generator storage tanks may be allowed without a RCRA TSD permit. Hazardous waste point of generation, an important determination relating to these strategies, will also be discussed. Generators and processors will find this paper useful when evaluating their permit exemption potential

Jan 1, 1996

By Kathryn C. Sole

A novel solvent-extraction process for the refining of gold was recently commercialised, with the commissioning in May 1997 of a 24 t a-' refinery at Harmony Gold Mine in Virginia, South Africa. The MinataurTM Process (Mintek Alternative Technology for Au Refining) uses solvent-extraction technology to produce gold of 99.99% purity from the cathode sludge arising from a conventional carbon-in-pulp / electrowinning circuit. Implementation of this process introduces significant cost benefits compared with the conventional dore smelting / toll-refining route previously followed. This paper outlines the process, presents selected operating results obtained during the first few months of operation, and provides some details of the associated techno-economic advantages.

Jan 1, 1998