Search Documents

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By W. V. Bluck

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most any given power plant is now going beyond buying at the lowest delivered fuel cost and is now taking into consideration other factors such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1983

By Dennis Ofiara, Paul Zick

Two 8.2 m diameter flood control tunnels are being constructed in the Taylor Shale Formation beneath San Antonio, Texas. These tunnels use precast concrete segments as final lining. This paper describes the features of the segments chosen for this project. The tunnels are being excavated with a hybrid Tunnel Boring Machine. This paper also describes the features of the TBM which make the machine compatible to the type of segments chosen.

Jan 1, 1989

By M. A. Reyes, L. Yan

Heat and humidity buildup withn refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a lifesustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ.

By S. D. Rosenthal

"This paper will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia, and the journey within academia going into the second year. INTRODUCTION As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. Mining Engineering degree in May of 1982, my first job with Utah International in the Farmington area took me back to my home state of New Mexico. Some of you will remember that the early 1980’s was not a period of prolific opportunities for mining engineers; given low commodity prices, especially for copper (for example, Anaconda Company had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton). Gold was taking off in the mid to late 1980’s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia so after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma copper purchase, Beanup and HBI) and was reviewing assets and staffing so internal opportunities became scarce. Employees were encouraged to ‘leave the company and find work elsewhere.’ So, off I go to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, Arizona, and a posting with Phelps Dodge (now Freeport McMoran). After 12+ years without living close to snow we moved to the Denver area in a new position with Newmont Mining Corporation. Along the way I became a Professional Engineer (Nevada) and completed a Masters in Project Engineering and Management. After 11 years with Newmont, I moved to Butte, Montana where I accepted a position as Assistant Professor of Mining Engineering."

Jan 1, 2015

By William E. Hole

The sand and gravel industry provides an enormous quantity of materials vital to the maintenance of low-cost construction. There has been little effort to conserve this valuable natural resource. In fact, existing regulations which affect sand and gravel operations act more to waste these materials than to conserve them. Another factor affecting the industry is new legislation requiring the reclamation of worked-out pits. Although such legislation creates many administrative headaches for a sand and gravel operator, there exists the possibility through such legislation of gaining some conservation measures that could be helpful to the industry.

Jan 1, 1974

By Isabel F. Barton, Eytan Bos Orent, Mark D. Barton

A new examination of tabular uranium (U)-vanadium (V) deposits within the La Sal district places mineralization in the context of the complex fluid flow history that has occurred in the Paradox Basin and Colorado Plateau. As the only currently producing district of this deposit type in the region, the La Sal district provides excellent opportunities to study deposit- and district-scale features that can serve as exploration guides where exposure is limited. The absence of major structures along a narrow and elongate mineral trend that runs E-W across the southern part of the Utah-Colorado border indicates a regional lithologic control. The trend was likely influenced by Jurassic drainage patterns, as indicated by paleocurrent directions shown in Fig. 1. Fluvial sandstone host rocks in the Jurassic Morrison Formation contain significant evidence of multiple superimposed fluid systems that have progressively changed local mineralogy. Apart from the presence of ore minerals, remnants of fluid systems are preserved as cements including quartz overgrowths, compositionally distinct carbonates, and sheet silicates. New geochronology methods provide constraints on the timing of initial mineralization and later remobilization. U-Pb ages of calcite associated with ore minerals provide evidence for Early Cretaceous mineralization, whereas textures and K-Ar ages show that early-formed V-minerals were replaced at the expense of V-bearing micas and clays during the Eocene. The paragenesis of minerals in U(-V) deposits of the La Sal district reflects the complexity of a sedimentary

Feb 1, 2025

By Robert A. Haney, Scott G. Vail, Kenneth G. Fields

The Mine Safety and Health Administration, in cooperation with IMC Global Operations, Inc., conducted a joint study to determine the effectiveness of the technology currently in use at the mine to control diesel particulate exposures. IMC Global operates an underground potash mine using diesel-powered equipment to extract minerals. IMC uses a variety of technologies to control worker exposures to diesel particulate. These technologies include: ventilation, low sulfur fuel, oxidation catalytic converters (OCC), maintenance and work practices. The study was conducted over a two-week period, two shifts per day. During the first week (six shifts), baseline data on exposures and diesel particulate emissions were obtained. New OCC's were installed over the weekend on all equipment on the test section. During the second week (six shifts), data were collected to assess the effectiveness of the new OCC devices. In addition to exposure and diesel particulate emissions data, mine ventilation, engine exhaust temperatures and mine operational data were obtained. The primary means of determining diesel particulate concentrations was the respirable combustible dust (RCD) method. Gas concentrations carbon monoxide (CO), carbon dioxide (CO,), and nitrogen dioxide (NO,) were measured using passive dosimeter badges and gas bottles. Results of measurements of diesel particulate, gases, and air- flows were analyzed to determine the effectiveness of airflow and oxidation catalytic converters for controlling diesel particulate exposures. The use of oxidation catalytic converters resulted in reductions of both workers' exposures and diesel emissions.

Jan 1, 1997

By John L. Shafer

A process for the conversion of stibnite (Sb2Sj) concentrates, crude antimony oxide, or metal to a pure cubic antimonous oxide (senarmontite) has been developed on a laboratory scale. The conversion of stibnite to senarmontite has been piloted. The high purity of the final product is the result of forming antimony trichloride as a low temperature distillable intermediate. To obtain the antimony trichloride the stibnite, or crude oxide is slurried in molten antimony trichloride and reacted with gaseous hydrogen chloride. Antimony metal is oxidized to the trichloride with chlorine. The hydrogen sulfide produced from the hydro- chlorination of stibnite can be upgraded to a strength of 95% or greater for further treatment. The crude antimony trichloride is separated from the gangue by a preliminary evaporation and then is fractionally distilled and the trichloride distillate has less than 50ppm of arsenic and lead combined (the most troublesome impurities in antimony processing). The purified antimony trichloride is then hydrolyzed with sodium or ammonium hydroxide to produce the cubic form of antimonous oxide (senarmontite) to the exclusion of the rhombic form (valentinite) which is photosensitive. The advantage of this process is the ability to treat a wide range of antimony ores, concentrates, and metal to yield a high purity oxide in a controllable range of particle sizes.

Jan 1, 1975

By D. R. Gehring

Effective project management is an excellent technique for meeting a goal through set, well-defined objectives. Even though project management is successfully used throughout the world in various construction projects, underground mining has unique characteristics that require approaches that vary from classical project management theory. Typically, a project includes four main stages: definition, planning, implementation and control. Definition and planning are often the most overlooked stages, but are arguably the most important. This paper addresses practical techniques for the definition and planning of projects for underground construction.

Jan 1, 1996

By D. Burkhard, E. Herth

"Geologic structure and properties are the primary influences on ground control at San Juan Mine. Geotechnical properties of the coal seam and near seam strata, the presence of above seam sandstone paleochannels and water, are thought to be the leading contributors to ground control issues. It is the confluence of specific geologic conditions rather than isolated features that most often produce adverse conditions. Altering primary support installation and mining practices are done when unfavorable conditions appear during development. Installation of standing support is most often employed when adverse conditions develop at later dates. REGIONAL GEOLOGIC SETTING San Juan Mine is an underground coal mine located on the western flank of the San Juan Basin in northwest New Mexico. The San Juan Basin is contained within the south eastern region of the Colorado Plateau geographic province. The basin contains multiple coal bearing formations and is also a major producer of coalbed methane gas. San Juan Mine is stratigraphically located within the Fruitland Formation. From a prominent monocline marking the western boundary of the basin, the formation dips gently to the east towards the center of the basin. The primary driver for the deposition of coal bearing formations within the basin was the Cretaceous Inland Seaway. Multiple cycles of transgression and regression driven by sea level rise and tectonic subsidence deposited rock types from marine shale’s to terrestrial sandstones. The Sevier Mountains to the west of the seaway likely provided the sediment supply for the Fruitland Formation. During a major cycle of seaward regression, the Pictured Cliffs Sandstone Formation prograded over the marine Lewis Shale. The coal bearing Fruitland Formation followed, being deposited over the Pictured Cliffs. The Fruitland Formation contains numerous coal seams and is approximately 400 ft. thick at San Juan Mine. Fruitland Formation coal seams are numbered in order of superposition. San Juan mines the Fruitland number 8 seam. Dating has placed the age of the seam at approximately 73 to 75 million years [1]. LOCAL GEOLOGIC SETTING The Fruitland 8 coal seam dips approximately 1-3 degrees towards the E-NE. At San Juan Mine, the seam displays a mild plunging, synclinal structure, the axis roughly bisecting the mine from west to east. The number 8 seam consists of five coal benches and four volcanic ash band partings labeled sequentially based on superposition. The lowest portion of the seam is the 8-1 bench, the 8-2 through 8-5 benches following sequentially to the top of the minable seam. Ash band partings are labelled P1 through P4 from bottom to top respectively. The presence of distinctive partings and benches allows for seam definition and aids in identifying mining horizons."

Jan 1, 2016

By P. N. Bradbury

The coal companies of today have to make all of their in-the-field managers MAINTENANCE PRODUCTION MANAGERS. By using a computer application to monitor all aspects of the daily production as well as the maintenance, a company can immediately effect a cost reduction by studying the down-time and delay trends on an everyday basis. This paper will outline how a company can use a program to not only put a stop to the increasing supply and maintenance costs but start trimming each of these cost centers while actually increasing the efficiency and productivity of the current work force.

Jan 1, 1991

By R. C. Beers, R. J. McKinley, R. D. Stewart

Preliminary test results at Occidental Research Corp.’s Irvine, CA, research facility indicate the viability of a new induced fluorescent sorting technique for preconcentration of limestone, coal, and oil shale. The patented “Oxylore”* process is a preconcentration stage that takes advantage of selective surface chemistry to label either ore or gangue particles with a fluorescent coating that can be detected by activation with ultraviolet light. The technology was originally developed by Ted Matthews (SME-AIME Fall Meeting, 1974, Preprint 74-B-328) and was acquired by Occidental in 1977. The firm has continued development of the process since its acquisition.

Jan 6, 1980

By J. L. Post, L. Borer

Small seams of fibrous tremolite and actinolite commonly occur in many California counties. A number of larger seams of this fibrous material were mined from 1882 until about 1955. The fibers from these mines were used for making acid filters, battery cases and fire-resistant paint. With increasing population, new residential areas are being developed in the foothill regions, leading to increased contact with seams of fibrous amphiboles. These forms of asbestos can be particularly dangerous to human health. Thus, it is necessary to determine the locations of these mines and adjacent veins and to identify the specific amphibole minerals present.

Jan 1, 2003

By S. Constantinescu

The alloys mainly used for short (or segmented) chip material cutting (cast iron, porcelain, etc) are alloys of the WC-Co type; in some cases with small additions of other carbons. The same alloys but of different granulometric classes are also used for pieces exposed to wear (wire drawing, moulds) The higher performance of the WC-Co alloys in chip machining applications is accounted for by their very good heat conductivity, which is 2-3 times higher than that of fast steels. The hard-alloys producers can resort to a wide range of possibilities to achieve variation of properties of a WC-Co composition and thus they can adapt their products to the particular type of tools they may choose to manufacture. The present metallography technique allows for a correct identification and evaluation of hard sintered carbons structures. The metallography approach is an indispensable method of investigation and control in the industry.

Jan 1, 2008

By Z. T. Bieniawski

After many significant advances in mining, including development of sophisticated methods for strata characterization and numerical modeling analyses, the engineering design process in mining strata control is as primitive as it was two decades ago. Yet, major advances in design methodologies have occurred in other branches of engineering. Is creative design in mining a myth only? Are we deluding ourselves when we talk about innovative mining design of today? Did you know that most design experts are often unaware of their own decision-making processes? This paper explores the methodology of creative engineering design as a new recognized discipline.

Jan 1, 1987

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By J. Y. Kim, R. W. Stanley, L. Rosato

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In this study, the flotation response of silver, from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high-acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (AgCu) 2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron, which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1992

By J. Harrison Daniel

More stringent dust standards, because of quartz in coal, have become a major compliance problem for the coal industry. Reducing quartz levels has become the major focus of the Bureau of Mines dust control research program. Results to date have identified hath the sources of quartz and prospective control technology. Control techniques are being developed for both room-and-pillar and longwall mining underground operations. Techniques include changes in face ventilation, mining cycle modifications, and better roof bolting dust control.

Jan 1, 1985

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

A high calcium fluidized-bed combustor ash was shown to be an effective binder for iron ore pellets at dosages of 1 % to 2% of the magnetite concentrate weight. Magnetite pellets that were between 1.1 and 12.7 mm (7/16 and 1/2 in.) in diameter were produced with dry crushing strengths greater than 22.3 N (5.0 lb-force) per pellet, which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. The addition of calcium chloride at a rate of 0.1 % to 0.2 % of the total powder weight increased the strength of the dried pellets by as much as 22 % compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1999