Search Documents

By B. Z. Weiss, N. R. Comins, F. Blum

Some aspects of the mechanical behaviour of chromium-containing dual-phase 3CR12 steel were investigated as a function of the temperature and strain rate. The yield stress was found to depend on both the temperature and the strain rate, with no substantial differences between the longitudinal and the transverse directions. The strain-rate sensitivity decreased with increasing temperature. The yield stress could be presented as a function of a temperature-strain-rate parameter. Impact test results showed substantial differences between the energy absorption of the transverse and longitudinal specimens above the ductile-brittle transition temperature. Changes in energy absorption with temperature were gradual for specimens in both orientations, and the transition from ductile to brittle behaviour occurred between 373 and 173 K. Strain rates ahead of the tip of notches with different geometries were calculated and measured experimentally.

Jan 1, 1990

By J. J. C. Heynike

The relationship between population growth and steel consumption since the beginning of the twentieth century is indicated, reference being made to the increasing capacity of production units and the resultant increased pollution in the same area. The need for the control of fugitive emissions with its associated high cost is pointed out. There is a direct relationship between energy and pollution, and examples are given of several improvements that have been made to achieve better energy usage and reduced pollution. Several practical examples of air-pollution control systems are described as applicable to the main metallurgical steel processes of today. In conclusion, reference is made to the fact that, with the improvements attained in reducing pollution, the public will not tolerate a decline in the standards already attained. Environmental control and better energy utilization will continue to be important aspects of steel-plant design and operation.

Jan 1, 1978

By use of a finite-difference model of an experimental galvanic cell, the effect of a resistance in the metalic conduction path on the potential and current distributions in the cell was predicted. The model predictions were compared with experimental measurements of potential profiles (measured by use of a scanning reference electrode) and galvanic currents. The predictions agreed well with the experimental measurements. Apart from this model, which is applicable in macroscopic cells (Le. with an electrolyte of low conductivity), a calculation procedure was developed to predict the effect of an external resistance on the galvanic current in a microscopic cell (high conductivity). The responses of the galvanic currents in the microscopic and macroscopic cells to changes in the external resistance were compared. From the similarity of the responses, a simple practical procedure for the evaluation of the external resistance (meter resistance) that can be tolerated is proposed.

Jan 1, 1989

By A. C. Legg

BCL Limited operates a nickel-copper flash smelting operation at Selebi-Phikwe, situated in north-eastern Botswana. The original furnace was commissioned in 1973 and produces a high grade sulphide matte, from its own concentrates plus additional custom feeds, which is shipped to refineries in Zimbabwe and Norway for further processing. In 2004 the company embarked on a study to modernize the flash smelting complex, with an emphasis on extending campaign life, improving the furnace integrity and enhancing throughput and process efficiency. First phase initiatives from this exercise, including the fundamental switch to a single concentrate burner operation of the flash smelting furnace, were implemented in July 2007. This paper summarizes experiences prior to implementation, details the specific improvements made to the flash smelting furnace and associated operations, highlights the improved plant performance after modernization, and outlines second phase expansion plans that are currently under consideration.

Jan 1, 2009

By M. J. Gouws, T. P. Knoetze

The spontaneous combustion of coal and the explosion of coal dust are two phenomena that were identified by the South African mining industry as requiring investigation. Research contracts were awarded to the G.P. Badenhorst Research Facility of the CSIR and the Department of Mining Engineering of the university of the Witwatersrand by the now defunct National Energy Council. Both projects entailed tests on numerous coal samples in specially designed apparatus. Since the completion of the project, attempts have been made to predict experimental results without incurring the cost of performing experiments. This paper describes predictive indices, based on routine laboratory tests, that were developed by the different research teams for their particular projects. A comparison of the results obtained by applying the spontaneous combustion liability index and the explosibility index to common coal samples indicates that, in general, propensity to spontaneous combustion and explosibility exhibit an inverse relationship. A brief overview is given of some major South African coal-mine disasters.

Jan 1, 1995

By R. K. Brummer

A simplified two-dimensional plane strain numerical technique for the non- linear modelling of a tabular mining excavation in brittle host rock under high stress conditions is described. The model has been developed using relatively straightforward assumptions based on extensive underground investigation of the fracturing and deformation of rock at the stope face in deep gold mines on the Witwatersrand, together with observed rock behaviour under laboratory conditions. The reef rock is modelled as a linear string of yielding elements which interact horizontally, while the elastic rockmass remote from the reef is modelled using boundary element techniques. This elementary technique is shown to produce results which agree closely with the observed behaviour of the fractured rock during the mining of a remnant pillar

Jan 1, 1987

It is a great honour to officiate at the celebration of the centenary of the South African Institute of Mining and Metalurgy. Tonight's festivities bring back happy memories of my association with South Africa's mining industry during my tenure of office as Minister of Mineral and Energy Affairs. They also remind me of the illustrious personalities who have preceded me on this podium. The Pioneers They include Sir Percy Fitzpatrick, who spoke in 1909 on the eve of the Union, General Smuts, and, on many occasions during the 1920s and 1930, Jan H. Hofmeyr. The basic issues addressed by them continue to enjoy the Institute's attention today, namely the optimal and safe exploitation of our country's mineral resources and cost-effective extraction of minerals from their ores. Translated into the Institute's key objective it reads: To initiate and give effect to the means whereby the requirements for technology and scientific knowledge if the minerals and metals section if the South African economy is satisfied.

Jan 1, 1994

By J. C. Zachariades, D. M. Fraser

The leaching of pyrolusite in acidic ferous sulphate solution was studied so that the important factors governing the kinetics of the reaction could be determined. The reaction is very rapid, and was monitored by continuous measurement and logging of the redox potential in solution by use of a microcomputer. The relationship between redox potential and manganese extraction was established empiricaly for each set of conditions by the use of a technique in which a calibration run was conducted in paralel with each leaching run. The study involved a number of batch leaching runs, and demonstrated that, of the variables investigated, only the initial ferous ion concentration and the reaction temperature afect the rate of manganese extraction. The final extraction did not vary. The reaction was modeled from the results by use of the shrinking-core model and Britan's activation-energy model. The later was found to provide a significantly better fit to the data.

Jan 1, 1991

By A. M. Copeland, A. J. Barrett

The use of hydraulically placed backfill in the deep gold mines of South Africa has increased rapidly over the past decade. The backfill that is delivered to the placement areas has a relatively high moisture content, and it is therefore pumped into geotextile containment bags that allow excess water to drain out but retain solid particles. The specific problems associated with this process that are addressed in this paper include the loss of solid particles entrained in the excess water, the rate of strength gain of the backfill, and the post-placement shrinkage of the backfill. The results of laboratory, surface stope, and underground tests are described. The parameters that were varied included the slurry density, the particle-size distribution, and the feed rate of the slurry the concentration of added flocculant; and the type of geotextile used as containment. Suggestions are given for the optimization of the placement properties of backfill.

Jan 1, 1994

By J. R. de Wet

The behaviour of mild steel in aqueous cyanide solutions similar to caustic cyanide elution solutions was investigated at high temperature in electrochemical experiments. The anodic polarization diagrams of mild steel indicated that steel may undergo active dissolution under these conditions. The rare occurrence of gold plating in practice is the result of the limiting of the anodic dissolution of the steel by the presence of a passive layer on the steel. This passive layer is stable only in a certain potential range, and the free corrosion potential attained determines whether the steel will be passive or active. For conditions typical of elution columns, several corrosion potentials are possible, depending primarily on the initial condition of the steel and the concentration of oxygen in the solution. If these conditions result in the formation of a passive layer on the steel, changes in concentration and temperature will not necessarily result in plating since the layer may exist in a metastable form.

Jan 1, 1993

By W. A. Lenhardt

During the past five years, several research projects on the causes of mining induced seismicity have been carried out by the Rockburst Research Department at Western Deep levels Limited. This paper summarizes the results of these investigations. Several types of mining-induced seismic events are addressed, and models of their mechanisms are presented. It is shown that most of the seismicity results from mining in geologically disturbed areas, and ways and means are discussed to reduce the seismic potential. Stabilizing pillars, for instance, have been introduced to reduce stresses at the stope face and to alleviate the facebursting problem. Facebursts still occur in areas of very low stresses, and pillars became the source of very large seismic events (M >3). At this stage, the understanding gained of pillar-associated events allows a review of current mining practices. Further, it makes possible an examination of the efficiency of measures to alleviate the effects of various seismically prone situations.

Jan 1, 1992

By R. J. Dippenaar, J. C. van den Berg

This paper describes an investigation into the prereduction of hematite fines in a fluidized-bed reactor as a means by which they can be prepared for direct smelting in a transfered-arc plasma furnace. A single-stage fixed fluidized bed reactor using the in situ gasification of coal was employed. It is shown that the hematite is reduced to magnetite at 1000 QC, the degree of reduction being limited by the inherent shortcomings of a single-stage reactor in which both the gasification and the reduction reactions have to occur. Methods by which the degree of reduction can be increased are suggested. The gasification process was studied in some detail, and three different reducing agents are compared. The dominating effect of the Boudouard reaction on the behaviour of the fluidized bed is clearly illustrated. Non-coking coals of high reactivity are best suited to this process, a finding that would complement the trend away from coke as a metallurgical reducing agent.

Jan 1, 1989

The relationship between the aspect ratio and physical fields in aluminium reduction cells wase studied numerically. The aspect ratio was firstly defined and 7 kinds of 320 kA cells with different aspect ratios were put forward. By using numerical simulation, the relationship between the aspect ratio and the electric-magnetic flow fields, magnetohydrodynamic stabilities, and thermal stability was discussed. It is concluded that the electric-magnetic flow field distributions are greatly affected by the aspect ratio. From the perspective of magnetohydrodynamics stability, the larger the aspect ratio is, the more stable the cell will be. A larger aspect ratio is more beneficial for the thermal stability under the same current density.

Jan 1, 2011

By R. A. H. Lycett, P. R. Jochens, D. D. Howat

The crystallization of rutile from titaniferous slags by R. A. H. LYCETT, M.Se. (Eng.),"A.M.I.M.M. (Visitor), P. R. JOCHENS, Pr. Eng., M.Se. (Eng.) (Rand), Ph.D. (Member), and D. D. HOWAT, B.Se., Ph.D., F.R.I.C., F.I.M. (Fellow) Factors affecting the precipitation of rutile from smelter slags were investigated, with particular reference to the effect of additions of phosphorus pentoxide to the slag. The phases were identified and the phase boundaries determined for slags having phosphorus pentoxide additions of 0 to 50 per cent. The liquidus temperatures of these slags were determined, and a pseudo-binary phase diagram was constructed. Rutile crystallized as the primary phase from melts having a phosphorus pentoxide content of more than IS,S per cent. Prismatic rutile crystals whose TiO. content was more than 97 per cent were grown from melts that had a phosphorus pentoxide addition of 30 per cent. However, the morphology of the precipitated rutile was such as to make subsequent separation impracticable.

Jan 9, 1975

By C. Musingwini, M. Woodhall

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility, mainly due to its nebulous nature. If one glosses over technical operating flexibility the resultant mine layouts and schedules tend to be sub-optimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. This paper illustrates the nature of technical operating flexibility, reviews previous work on valuing operating flexibility and proposes how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility is quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility, ore availability.

By B. G. Meyburgh

SYNOPSIS As a result of a test programme over a period of approximately ten years and a decision to extend the uranium plant, it was decided to design and erect the first full-scale Purlex Plant in the Republic of South Africa. The plant at Buffelsfontein G.M. Co. Ltd. was commissioned in August, 1968, and to date has produced results superior to those predicted in the original estimates. The capital expenditure was R678 000 for a plant capable of treating 1 600 gallons per minute of pregnant solution. Compared with the conventional resin ion exchange process, it has been found that the saving in production costs is 21 cents per pound U3O8 produced. The amine loss is 10 parts per million, which is equivalent to a total organic loss of 250 parts per million. The uranium loss in the raffinate is less than 0.001 g/l U3O8. The final product is of a high quality and it is probable that it is pure enough to convert to the fluoride directly.

By J. T. Collins, C. J. Cloete

Secunda Collieries forms part of Sasol Coal, the coal division of the Sasol Group of companies, and already produces 29 Mt of coal per annum from its four collieries: Twistdraai, Brandspruit, Bosjesspruit, and Middelbult. The successful establishment of this mining complex was achieved only through a unique team spirit in which the central services and the decentralized teams under the leadership of the mine management of each of the four mines played an important role. The Secunda mining complex has now reached the optimization phase, during which the mining cost, productivity, safety, and quality of work become as important as production. The setting of priorities and problem solving over the long, medium, and short term are essential for improving the performance of the four collieries. Management had to adapt to the fast-changing environment during the enormously fast build-up of production. The major challenges in the environment were posed by the frequent dolerite intrusions, the extremely hard cutting conditions caused by carbonated nodules and thin sandstone intrusions in the coal seam, and excessive roof and face pressure in some areas due to semi-massive sandstone formations in the rock strata.

Jan 1, 1986

By M. Cortie, L. Iorio

The amount of nitrogen contained in an austenitic stainless steel affects its properties significantly. The maximum content of nitrogen feasible in a range of experimental low-nickel austenitic stainless steels containing significant additions of copper is evaluated The nitrogen content is calculated based on published interaction coefficients, and by use of the FACT thermodynamic computer program and database. The differences between the two methods of prediction can be attributed to inaccuracies in the published interaction coefficients. The calculated nitrogen contents of some experimental alloys are compared with the actual nitrogen contents obtained when the alloys were produced in an induction furnace. The actual nitrogen contents obtained were higher than those predicted by either method, and this is believed to be due to a super saturation of nitrogen occurring in the melt, which was not relieved during the short period in which the charge was molten. It was evident that the experimental alloys can contain between 0,25 and 0,40 per cent nitrogen (depending on temperature, composition, and nitrogen pressure) when melted in a sealed induction furnace, and this is more than adequate for the purpose of forming and stabilizing the austenite phase.

Jan 1, 1994

NIM Reports Report No. 1563 Neutron activation analysis of samples from the Kimberley Reef Conglomerate. Report No. 1569 The use of DDTU as an analytical reagent for the noble metals. Special general meeting A Special General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 14th November, 1973. The President, Mr P. W. J. van Rensburg, opened the meeting at 9 a.m. and read the notice of the meeting, which was as follows: Colloquium and general meeting CONSTRUCTION OF SLIMES DAMS A General Meeting and Colloiquum on the above topic was held on November 14th and 15th, 1973, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 135 delegates and was opened by the President at 9.10 a.m. Orange Free State Branch PROCEEDINGS OF THE ANNUAL GENERAL MEETING The Annual General Meeting of the Branch was held in the Western Holdings Cant,een on Tuesday, 11th September, 1973, at 7.00 p.m. Book Review Westwood, W., and Cooper, B. S. Analytical methods in use in non-ferrous minin~ and metallur~ y: a selective review. London, Institute of Mining and Metallurgy, July 1973. 54 pp. £3.50.

Jan 12, 1973

By D. Harbottle, D. Rhodes, T. F. Jones, S. R. Biggs

Multiphase process design and optimization often depends upon the rheological properties of sludges and slurries. In practice the task of determining these important properties is usually carried out by removing small samples from a process line or process unit and performing tests with proprietary bench-top analysers near to site or at a remote laboratory. Sampling will remain an important procedure in industrial processes, but there is also a strong case for augmenting the routine information obtained using an in situ sensor, as suggested below. ?Sampling protocols can result in extensive turnaround periods from sample collection to the generation of results. The delay can have an effect on a variety of factors such as product quality, process operability and efficiency. ?Sampling of toxic or radioactive material can prove an even greater challenge to minimize human involvement. ?Removal often changes the rheology of a specimen, and might lead to incorrect conclusions being drawn about the condition of a sludge. ?Sludge and slurry in a containment suffers a gravitational gradient, so that a removed sample should be paired with its location, particularly in the vertical dimension.

Jan 1, 2007