Search Documents

By R. Sharma, I. Miskovic, S. Miskovic

Solvent extraction (SX) is a widely used method for the extraction of copper from pregnant leach solutions or other ionic solutions in hydrometallurgical applications. About 17% of total refined copper production worldwide is produced using SX followed by electrowinning (EW). Conventional SX units, such as mixer-settlers, consume a large amount of extractant, offer poor process control and yield low extraction efficiency. Extraction efficiency is poor due to low specific interface area, crud formation, emulsification, and slow phase separation stage. Micro solvent extraction (micro-SX) is a rapidly developing technology that provides an opportunity for improved process control, higher extraction efficiency, lower residence time and, as such, has a potential to reduce the environmental footprint of SX operation. In this research, extraction of copper ions in an acetate buffer media is investigated using D2EHPA with kerosene as a diluent. Chemical factors such as extractant concentration and ionic concentration of aqueous phase are varied to determine the optimum conditions. Subsequently, the extraction efficiency and reaction time of new micro-SX reactors are compared against previous bulk SX studies. Extraction in the microfluidic reactor was observed to be faster with a residence time more than an order of magnitude lesser than bulk SX. This study forms a prelude for developing new modular micro-SX units which will enable continuous, effective, and safe operation on a large scale. In future studies, numerical and analytical models validated through this work will help eliminate rigorous experimentation and enable faster design and fabrication of micro-SX units. INTRODUCTION Conventional industrial solvent extraction (SX) units such as mixer-settlers, extraction columns present various disadvantages. Low specific interfacial area, crud formation, and emulsification in industrial reactors lead to long extraction times and severely hamper extraction efficiency (Priest et al., 2011; Chen et al., 2017). Microfluidic extraction considerably improves upon the current extraction practices by (1) creating a large surface to volume ratio that enables rapid mass transfer across the interface, (2) better process control, and (3) easier separation of phases (Kashid, Renken, & Kiwi-Minsker, 2011; Ciceri, Perera, & Stevens, 2014). These factors establish micro-SX as a crucial mode for process intensification. Although, a micro SX unit has significantly low processing volume than conventional extraction methods, their throughput can be increased via massive parallelisation (‘numbering up’), which is an area of active research (Darekar, Singh, Mukhopadhyay, & Shenoy, 2016a; Kriel, Woollam, Gordon, Grant, & Priest, 2016).

Jan 1, 2019

By F. W. Guernsey

Of all the elements, sulphur occupies a place by itself. It is mined in situ, in such quantities and of such purity that, as regards the tonnage produced, it is the first of any element on the list. Iron and coal the great tonnage producers, are combinations of elements, while sulphur is mined and marketed almost chemically pure. It is sold, in large quantities, commercially, calling for a purity of 99.5 per cent while for medicinal purposes, the Pharmacopoeia requires only 99 per cent. purity. It is a very common commodity, and like many common things is of extreme importance, in the progress of our civilization. The substance has been known from the earliest times, the word sulphur being derived from the Sanskrit Culvari", hence the Latin Sulphur. Commercially it is also called brimstone, this word being a derivative of the Anglo-Saxon Bryne Stane or burning stone. From our younger days, we have been more or less familiar with the mineral. On the spiritual side being threatened, if we did not behave ourselves, with an ultimate consumption in a lake of fire and brimstone, (which in moments of reflexion was not pleasant to contemplate) while our bodily ills were taken care of by inward applications as a spring medicine. In both instances, the effect required, was generally attained. Sulphur occurs in nature, both free and in the combined state, it being estimated that it forms, over one tenth of one per cent of the first ten miles of the earths surface. (I do not know who did the estimating and it is not guaranteed).

Jan 1, 1923

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By S. Goodman

Successful exploration for and exploitation of a mineral deposit requires an accurate understanding of the deposit architecture in 3D, and of the development of the mineralizing system through time, which requires a thorough comprehension of the structural framework of the deposit. The integration of geological, geophysical and geochemical datasets to arrive at a 4D structural framework is well-established and has been successfully applied by SRK Consulting in projects from deposit to regional scale. In some cases, we can go beyond this, applying the SEEBASETM technique, which utilizes a ?bottom-up? approach to basin analysis. SRK?s approach primarily relies on the interpretation of magnetic and gravity data, calibrated with many other datasets including mapped geology, topography, event histories, wells/drillholes and seismic data. The SEEBASETM model is a culmination of this data integration and is produced through an iterative process of structural interpretation and geophysical modeling, where an interpretation of basement composition and 4D structure is used to constrain depth-to-basement geophysical modeling, and the modeled depths are then used in conjunction with the structural interpretation to constrain contouring of the basement topography. The result is a rigorously calibrated, 3D view of the basement surface, which can be used to understand the basement and basin architecture, and thus serves as a predictive exploration model. This technique, which was developed for use in the petroleum industry, is now finding success as a predictive tool in mineral exploration.

May 1, 2003

By W. E. Cockfield

This paper is not intended as an original contribution to this subject, but rather as a review of the main theories which are held with regard to placer deposits, with, of course, particular reference to the placers of British Columbia. The present interest in gold mining has, however, brought the subject of placers to the fore, and possibly a brief outline of the geology of such deposits will serve as a basis for discussion on the subject. In Canada, the most valuable of our placers are deposits of gold, and consequently the discussion will centre largely on placer-gold deposits. The same principles apply, of course, to placer deposits of other metals. The Origin of Placer Deposits As a starting point, the idea which is prevailingly held is that placer or alluvial gold is detrital in origin, that is to say, the gold originally existed in veins, lodes, or disseminations in the country rock of the regions in which the placer deposits are now found, and that, through the various erosive forces of nature, it was liberated from those veins or lodes and concentrated in the form in which we now find it. 1 have not time to go thoroughly into the proof of this, but the lines of evidence are many. If we take the Cariboo district as a typical example, Johnston and Uglow(l) have shown, first of all, that the placer and vein gold are identical in character. Crystals occur both in the placers and in the lodes, but the crystals in the placers are nearly always slightly worn, indicating transportation.

Jan 1, 1932

By A. L. Mular

"On behalf of Bob Bruce and myself I would like to begin by stressing some key points.First, most of us know that the Canadian Mineral Processors was formed in 1969 and is an offshoot of the Canadian Gold Metallurgists. I attended that first meeting in 1969, and I haven't missed a meeting since! Pretty obvious that CMP serves the best booze! At any rate, we know that our meetings are supported by CANMET. Camsell Hall is always at our disposal; Bob Bruce acts as permanent secretary pretty much free of charge; we receive a financial grant from CANMET. This brings me to a second point.Second the Canadian Mineral Processors do not enjoy a free ride in this relationship. CMP provides a genuine service to the mining industry, to government, and to universities. For the industry, CMP serves as a forum for the rapid dissemination of new ideas and new technology developed at remote locations throughout Canada. New developments outside Canada are introduced by invited speakers at our meetings. The effect is to help reduce operating costs and increase efficiency.For government, problem areas and research priorities can be isolated through mutual discussions. Direct communication at our meetings can help CANMET to temper its goals and modify its national priorities.For universities, CMP provides a wealth of operating experience and practical know how. The yearly proceedings are a major current reference source fo1· those of us who teach mineral processing. Admittedly, the proceedings are publ-shed from CMP coffers. However, I note that our fees are up this year, which brings me to a third point.Third, we face some potential problems of a financial and political nature. From a financial view, we may lose our CANMET grant and other financial good will simply because of spending constraints. Our fees are expected to climb each year thereafter.From a political view, we know that the metallurgical society of CIM is anxious to incorporate CMP as a section. The pros and cons of such a merger have been described in a recent mailing. In th2 final analysis, the political and financial problems are interrelated. There are several alternative solutions to both problems, which brings me to a fourth point"

Jan 1, 1979

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016

By A. H. Lang

"The great interest taken in uranium in Canada during the past few years has resulted in the discovery of a very large number of occurrences, and in much research that has added to the knowledge of the mineralogy and geology of uranium deposits. The object of this paper is to present that information in condensed form. Some of it has been published before, but the writer has been asked to bring it together and to add more recent, unpublished data. The paper therefore contains short accounts of the mineralogy of uranium and of the types and distribution of occurrences; brief regional descriptions, including information on some of the characteristic deposits; and conclusions regarding prospecting and development possibilities.The writer has access to much confidential information supplied in compliance with regulations of the Atomic Energy Control Board. He has used this only for making broad generalizations that could not affect individual interests, and only where the owners of properties have agreed to its use.Much of the information on mineralogy and geology is derived from the work of others. The writer is particularly indebted to M. H. Haycock and S. Kaiman of the Mines Branch; H. V. Ellsworth, S. C. Robinson, E. J. Brooker, H. R. Steacy, W. E. Hale, and A. M. Christie of the Geological Survey; and E.W. Nuffield, J. S. Stevenson, and other officers of provincial Departments of Mines. For information and many courtesies he is greatly indebted to so many officers of Eldorado. Mining and Refining (1944), Limited, and owners and staffs of private properties, that it is impossible to mention them individually."

Jan 1, 1950

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944

By M. H. Allan

"This paper presents the geographic and geological setting of Saskatchewan Power Corporation's Poplar River Mine in south-central Saskatchewan, about 8 miles from the U.S. border. Generally the mine, which is being expanded to four million tons per year, is in an extremely disturbed geological area with severe dewatering problems. The lignite coal, which is strip mined, is supplied directly to an electric power generating station by means of a 7-mile unit-train private railroad.A number of unique reclamation and socio-economic problems were encountered because of the proximity to the U.S. border and because of the lack of experience of the regulatory authorities in projects of this kind. These are described in some detail, as well as the performance of one of the largest draglines in Canada. IntroductionThe Saskatchewan Power Corporation is a publicly owned utility which has the franchise to supply electricity and natural gas to all customers within the boundaries of Saskatchewan.Saskatchewan is a province which can almost be divided in two: the populated southern portion, principally devoted to farming, and the northern portion which is mostly on the Precambrian Shield and consists of lakes, rocks and muskeg. This portion is largely uninhabited except for a number of small villages. However, in the last few years there has been considerable mineral exploration and development, notably for uranium. This has helped considerably in the diversification of the basic agricultural economy of the province.Saskatchewan consists of 251,700 square miles, 761 miles north to south and an average of 335 miles east to west. It has a population of approximately 960,000, giving a population density of four persons per square mile. The Saskatchewan Power Corporation supplies 357,249 electrical arid 221,378 natural gas customers."

Jan 1, 1982

By G Zahary

THE most acceptable approacl1 to analyzing rock behaviour, at the present time, is based on the application of principles of mechanics and strength of materials. Analyses have been made in which the criterion of failure is based on maximum stress (1) and on Mohr's rupture theory (2). If such analyses are to be carried out, the mechanical properties of the rock must be known within acceptable limits. Although an adequate correlation of laboratory test results with field conditions has not been established, test results have been published (3) on the basis of their comparative value. That is, test results may be useful for comparing the behaviour of different rocks under similar loading conditions or of a particular rock under different loading conditions. This study aims at establishing some of the mechanical properties of an andesite rock by testing specimens cut _from diamond drill core. Drill core (EX) was provided from run-of-mine drilling by New Dickenson Mines Ltd. and Campbell Red Lake Mines Ltd.

Jan 1, 1963

By I. Donohue, M. Pearson, E. Barrette

"This paper presents the technique and benefits of the finite element approach for designing the refractory lining in pressure oxidation autoclaves. One-dimensional equations are used to develop an initial refractory design. ANSYS Parametric Design Language (APDL) scripts are then used to build and analyse a more accurate three-dimensional finite element model to verify the refractory thickness, determine weld overlay requirements, and assess mechanical stability. The APDL scripts provide a cost effective means to quickly evaluate various boundary conditions and multiple designs to determine the optimal lining configuration and nozzle layout.INTRODUCTIONNew ore processing facilities demand increased capacity, requiring hydrometallurgy processes that have larger reactor vessels operating at higher pressure and temperature. Many pressure hydrometallurgy operations require vessels with an impermeable membrane and one or more courses of refractory or ceramic brick. The membrane provides corrosion protection for the vessel shell and the brick provides thermal protection for the membrane. Designing a refractory lining with an economic service life as a thermal barrier requires the refractory to be erosion resistant, chemically compatible with the process fluid, and mechanically stable. A fundamental understanding of the factors affecting the lining system is essential as designs move further away from the industry’s experience base.During basic engineering the refractory lining design is developed using one dimensional cylindrical conduction equations for heat transfer and classical hoop stress-strain relationships for determining mechanical stability. The results of the thermal calculations specify the refractory thickness that should prevent the membrane temperature from exceeding the design limit. Mechanical stability of the lining is determined by examining the sensitivity of lining stability with respect to various parameters. There are three criteria that must be satisfied to conclude mechanical lining stability:"

Jan 1, 2012

By K. Swedburg, M. Samuels

"The expansion of the concentrator at New Gold’s New Afton copper-gold mine in British Columbia, Canada, completed in 2015, included an increase in the required retention time of the cleaning circuit. On site pilot testing of a Woodgrove Staged Flotation Reactor (SFR) had shown that a high grade copper concentrate would be produced with excellent recovery. The SFR was selected rather than conventional tank cell technology based on the much smaller footprint (which rendered a separate and expensive building extension unnecessary), high concentrate grades demonstrated in testing, and the lower energy requirement. Three SFRs, each capable of taking a nominal feed of 700 cubic meters per hour were installed and commissioned 10 months after the receipt of order. The SFRs operate in series and all of the cells produce a final concentrate typically grading 32% Cu, while the overall SFR stage recovery averages 55%. The tailings from the SFRs are treated in the original conventional three-stage cleaner circuit where the remaining values are recovered in a concentrate grading 28% Cu. Design production was achieved within days of the initial start-up of the SFR circuit.INTRODUCTIONThe New Afton concentrator, located near Kamloops, British Columbia, Canada processes a copper-gold ore with a designed head grade of 0.96% Cu, 0.72 g/tonne Au, and 2.22 g/t Ag.The New Afton Mine is a block cave mining operation. Ore is undercut from the bottom up and removed at the extraction level from a grid of draw points. Ore is trammed to the ore passes by underground loader and dropped to a haulage level for transport by trucks to the gyratory crusher. From the crusher, the ore is conveyed to the mill via a 4.5 kilometre long conveyor system. Block caving was chosen for the New Afton deposit because the underground infrastructure could be built below the historical open pit of the Afton Mine (a previous operation of Teck Resources) and this method is favorable to large-scale low-cost mining.The New Afton deposit is a copper-gold, alkalic porphyry system. Hypogene mineralization is characterized by discontinuous copper sulphide veinlets and disseminations, principally chalcopyrite and minor bornite, along with pyrite as the second most dominant sulphide. Gold particles vary in size from 5 µm to 40 µm and occur as native gold and electrum, associated mostly with the chalcopyrite grains and never with the pyrite. In some instances, a second alteration phase has resulted in the copper sulphides being replaced by tennantite-tetrahedrite locally and along faults that transect the mineralized body. The design head grade of arsenic is 244 PPM, although the presence of tennantite is inconsistent and can vary from trace levels to 15% of the total copper. No arsenopyrite is present in the hypogene ores. Supergene mineralization, consisting of native copper with accessory chalcocite occurs in minor amounts along faults and highly oxidized near-surface portions of the deposit."

Jan 1, 2016

By M. Sukhram, S. A. Argyropoulos

"In the aluminum and steel processing industries there is a need for velocity sensors to measure the flow characteristics of liquid metal. This paper will present a sensor and an inverse heat transfer technique to determine the direction of velocity in flowing liquid aluminum. Experimental research work with the sensor involving liquid aluminum was conducted, using the Revolving Liquid Metal Tank at the University of Toronto, which rotates 50 kg of liquid aluminum with velocities up to 0.35 m/s. Experimental data for various magnitude of velocity demonstrate that the sensor records different thermal profiles under different fluid flow conditions. Using the transient temperature information and the inverse technique, the direction of velocity of the molten aluminum flow field can be inferred. INTRODUCTIONOur research at the University of Toronto has focused on developing invasive sensors to determine the velocity of high temperature liquid metals. High temperature in this setting is defined at VALUES (in excess of 660 °C. The discussion which will persist in this manuscript involves detecting the direction of flow in liquid aluminum using an inverse heat transfer technique. We first reported on the sensor which is used in this article in the following two publications (Sukhram and Argyropoulos, 2011a; Sukhram and Argyropoulos, 2011b). The motivation to perform this research is due to the lack of sensors available to characterize the conditions within a high temperature liquid metal reactor/vessel. A report conducted by The Minerals Metals and Materials Society (TMS Energy 2011) has suggested that the introduction of sensors into molten metal processing environments has the potential to increase process efficiency up to 15%. Such sensors will aid in the understanding of high temperature liquid metal processing operations with the goal to implement more efficient process design and practice."

Jan 1, 2012

By P. R. Geoffroy

Extensive and Intensive Prospecting As often pointed out, the search for new ore deposits may be carried on along two widely divergent lines. It may be either extensive or intensive. By extensive prospecting we mean a search for mineralized outcrops conducted over large and more or less virgin tracts of land, followed by a test of the practical value of any discovery made, the test being limited to the immediate vicinity of the outcrop. Extensive prospecting, was, in fact, the only policy known to the early prospectors. of the American continent and is still the rule in the remote sections of the Canadian Shield and in the African wilderness. It can be further characterized by the lack of emphasis placed on geological and other technical means as an aid to the search for ore. However, very little virgin ground is left, nowadays, for a man or a company to test their luck, and whatever is left is so remote from the necessary means of development that any new discovery will require considerable delay and expenditures to be amenable to profitable mining. On the other band, a great many of the favourable and still unexplored areas (and this is particularly true in Canada) are overburdened to such an extent that outcrops of bed-rock are extremely scarce and extensive prospecting is nearly impossible. Intensive prospecting, to the contrary, must be understood as a detailed search for ore carried on over limited areas in districts already known to be mineralized and covering regional structures whose relation to mineral deposits bas been estahlis.hed with a fair degree ot certainty. The search for deep-seated deposits in the vicinity of successful mines is a perfect example of intensive prospecting. As a matter of fact, the majority of the geologists employed by the mining industry are engaged in some kind of intensive prospecting.

Jan 1, 1950

By Magdy Ibrahim

This paper presents experimental design and development of a low-cost remote sensing hardware designed to support automated site data acquisition for near real-time progress reporting of construction operations. The developed hardware utilizes open source microcontroller equipped with multiple sensors that include 3D accelerometer, GPS, Data logger and Bluetooth. The use of open source microcontroller makes the developed design cost effective; freeing it from the need for costly license fees. Its platform configuration is flexible; enabling the addition of temperature, weight and other sensors, Wi-Fi and Xbee capabilities to suit individual field applications. Pilot tests have been carried out in laboratory and outdoor environments. The results prove effectiveness and robustness of the developed configuration. The paper provides description of the individual components used in the development of this prototype hardware. It also describes the technical characteristics, capabilities and limitations of the developed hardware. The findings of comparison with alternative technologies used for outdoor tracking of construction operations are presented. The comparison is carried out with respect to range, cost and suitability for outdoor environment. The developed hardware is expected to support a wide range of applications including tracking of earthmoving operations, highway construction and onsite resources. As well, it is expected to enhance safety on construction jobsites.

Aug 1, 2013

By G. A. Young

THE Geological Survey was created in 1842 to aid the development of Canada's mineral resources. Although the institution has been in existence for nearly 100 years and has accomplished an immense amount of work, the need for its services remains as great as ever and, indeed, it is difficult to imagine a time when the country will no longer require a Geological Survey. This is so because of the tremendous effort required to make an adequate geological examination of so large an area as is embraced by Canada and partly because what today may seem an adequate geological examination proves, later on, to be inadequate. The ultimate objective of the Geological Survey is to complete the study of all phases of the geology of Canada, that is, to determine how and when the physical features originated, how and when the soils and other unconsolidated deposits were formed, and how and when the solid rocks and associated deposits were produced and assumed their present conditions. When the study has been completed, any only then, will it be possible to make a reliable estimate of the country's mineral resources. This appraisal embraces more than determining the value of already discovered deposits: it also involves attempting to establish what kinds of undiscovered deposits may be present and where they may occur. The estimating of the potential mineral wealth can be clone only after the geology of the country is known. Not until then will it be possible to forecast what types of valued deposits may occur in a district and what types will almost certainly be lacking. A thorough knowledge of the geology of the country is desirable not only to permit estimating the potential mineral resources but also as an aid in locating and developing mineral deposits whether these are of the nature of a bed of limestone, a seam of coal, a reservoir of petroleum, a vein, an irregular body of sulphides, or any other type of deposit.

Jan 1, 1940

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964