Search Documents

By R. S. Moehlman

IN recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. COST OF DRILLING Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 50 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $1 per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft., as more time is consumed in pulling rods. 3. Cost of preparing drilling stations, getting air underground to stations, etc. 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By H. Margolin, E. Ence

In order to understand the effect of zirconium on properties of Ti-Cu-A1 alloys, Ti-Zr alloys were examined for the presence of ordering or compounds at the following compositions in weight percent: 24.1 pct Zr (lZr:GTi), 32.2 pct Zr (lZr:4Ti), 38.8 pct Zr (lZr:3Ti), 49.0 pct Zr(1Zr:ZTi). Alloys were prepared as 15-g buttons by non- consumable arc melting under argon atmosphere from Bureau of Mines titanium (Bhn 63) and Reactor Grade zirconium (Bhn 150). Weight losses during melting did not exceed 1 pct of the initial button weight. Prior to heat treatment, buttons were hot-rolled at 600" to 700°C to rods of about 6 mm diam. Contamination after hot-rolling was found to extend to a depth of less than 0.5 mm. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. Annealing times were as follows: 700°C — 7 days; 600°C— 14 days; 575°C-1 and 2 months; 525°C-2 months; 500°C-2 months. Prior to heat treatment, all Ti-Zr alloys were vacuum annealed at 900°C to remove hydrogen. The reanneal of 575°C specimens for an additional month produced no observable microstructure changes. The results obtained by microstructure and X-ray diffraction are shown in Fig. 1, together with data of Hayes et al.' No other phases than a or P were found. Small amounts of retained P were detected by X-ray in the 49 pct Zr alloy. The data of the present investigation suggests that ß and a transus boundaries are at considerably lower temperatures than those of Hayes et al. The work of Hayes et al. is based on sponge titanium and Bureau of Mines zirconium, both of which contained 0.15 pct 0. Since melting was performed in

Jan 1, 1962

By E. Robert Ruhlman

The term potash refers to potassium oxide (K2O), a compound not found in nature or produced by man but used as a basis for comparison of all potassium compounds and now is applied generally to various compounds of potassium used by agriculture and industry. Potassium, the last of the three major plant foods to be used in appreciable quantities by agriculture, was originally produced only from organic materials for chemical uses. The first recorded identification of a mineral source of potassium was in 1797; but, until the discovery in 1839 of the large deposits of soluble potassium salts in Germany and their development in 1860-61, nearly all potassium compounds continued to come from organic sources. With the importance of potash to plant life discovered in 1840 by von Liebig and the production of potash in Germany after 1861, agriculture soon became the major consumer of potash. In 1958 agriculture accounted for about 95 pct of the total potash consumption; the chemical industry used the remaining 5 pct. Mineralogy and Geology Potassium, an important constituent of the earth's crust, occurs in many forms in numerous rocks and minerals, including water solutions, but is not found in its native state. Twenty-five of the more important potash minerals are listed in Table 1. The properties of the five potash minerals most common in Permian salt formations follow: Sylvite is isometric; has a hardness of 2, a specific gravity of 1.98, vitreous luster, and cubic cleavage; and ranges in color from clear to brick red. In taste it is similar to halite but has a sharper taste and a cooling effect on the tongue. It is very plastic under pressure. Langbeinite is isometric; has a hardness of 4, a specific gravity of 2.82, vitreous luster, conchoidal fracture, and no cleavage; and ranges in color from clear to gray. It is taste- [ ] less, somewhat granular, and slowly soluble in water. Polyhalite is triclinic; has a hardness of 3, a specific gravity of 2.77, and dull luster; and

Jan 1, 1960

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson' indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel's' data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,' Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

H. S. COE, St. Louis, MO. (written discussion *)-I feel much gratified that Mr. Mishler has confirmed those principles of slime settlement expressed by Mr. Clevenger and myself. I wish to state that, when we wrote the article referred to by. Mr. Mishler we had not seen his earlier article in which he gave a formula to be applied to the settling rate off feed pulp for determining thickener area required at El Tigre. It has been my experience that in cyanide work the settling area required is determined by the settling rate of the feed pulp for perhaps 20 per cent. of all of the ores to be encountered. For the other ores, the area required is greater than that indicated by the settling rate of the feed and corre-sponds to the settlement of a somewhat thicker free-settling pulp. Mr. Mishler, in his paper, has thoroughly outlined a set of tests for determining thickener capacity, which, if carefully carried out, should be entirely reliable, provided allowance is made for changes in the mill feed from time to time. Two features of his paper, I, believe; need comment. In speaking of the time required for slime to flocculate after being fed, Mr. Mishler quite properly states that the actual settling rate for the feed pulp can-not be that of completely flocculated pulp because of this time lost in flocculation. It seems to me, however, that this feature cannot be of very great importance, for the following reason: The upper zones of pulp in a thickener may be, and often are, as thin as the feed pulp. If, therefore, the feed be introduced at sufficient depth below the pulp surface to prevent agitation at the surface, there will be ample time for it to become flocculated before it becomes the surface layer, and it, will

Jan 1, 1918

By A. Sauveur

At the New York meeying of the Institute, February, 1914, Professor Hopkinson and Sir Robert Hadfield presented an important paper entitled Research with Regard to the Non-Magnetic and Magnetic Conditions of Manganese Steel.

Jan 1, 1915

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By N. A. Gokcen, S. Fujishiro

The dissociation pressure of Cr3C2 has been measured in the range of 1908" to 2237°K by means of graphite Knudsen effusion cells. It has been found that Cr3C2 vaporizes according to the following reaction: 1/3 Cr3C2 (s or 1) = 2/3 C (graph.) + Cr (g). The equilibrizcm pressure, P, of Cr (g) is found to be log Ps=- - (21,194/T) + 6.525 over solid Cr3C2 and estimated as log P, = - (19,535/T) + 5.76 over liquid Cr3C2. CARBIDES of chromium are of great importance in alloy steels and cemented carbides. The published data on their therm odynamic properties at high temperatures, however, are meager. The heat capacity and change in entropy of Cr3C2 were determined calorimetrically by Kelley and Moore1 in the range of approximately 50" to 300°K, and by Oriani and Murphy2 from 297" to 1188°K. The standard entropy of Cr3C2at 298.15°K, obtained by Kelley.7 was later confirmed by DeSorbo.4 Equilibrium in the reaction was investigated by Boericke.5 A recent tabular summary

Jan 1, 1962

By L. L. Handy

Two equations are compared for calculating imbibi-tion rates of water into porous media. A linear relation was found to apply when the square of the volume of water imbibed was plotted against time for water imbibing in natural rock materials. The effect of adsorbed organic materials on surface wettability was determined from measurements of rate of imbibition, water saturation and water permeability. INTRODUCTION An understanding of the mechanisms by which water displaces oil from porous media requires an understanding of the role of capillary forces in the displacement process. The capillary forces are determined by properties of the water-oil-solid surfaces. Consequently, some measure of the surface properties of reservoir rocks is necessary if displacement behavior in oil reservoirs is to be predicted from laboratory measurements. Several experimental procedures have been proposed to assign quantitative wettability indexes to reservoir rock surfaces. The most recent of these proposals are those of Bobek, Mattox and Denekas' and Amott.' These indexes are designed to show a continuous variation from the preferential oil-wet to the preferential water-wet systems. They require measuring some property of the rock which is a function of surface wettability. The quantities are measured on unaltered core material and compared with values obtained for known oil-wet and water-wet extremes on the same material. These methods are useful but are semi-empirical in nature. They have the disadvantage that the measured quantities may be functions of other variables in addition to surface wettability. Some understanding of the behavior of water-oil-rock systems may be obtained from studies of the simpler water-air-rock systems. Surfaces of a given wettability are more easily maintained for the latter. Also, certain approximations can be made for the flow of water and air which are not justified for water-oil flow. The theoretical and experimental work discussed in this paper is part of a study of the role of capillarity in the dynamic displacement of air by water. The expec- tation is that observations for the water-air system will lead to generalizations which are applicable to water-oil systems. THEORY Imbibition is defined as that process by which one fluid displaces another from a porous medium as a result of capillary forces only. Differential equations have been derived to describe the displacement of oil by water during imbibition, but these equations have not been solved.".' With certain assumptions, however, solutions are possible for water-air imbibition.

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By R. C. Nelson, T. L. Weaver, A. I. Michals

This paper describes the design and performance of an apparatus for making continuous nondestructive resistance measurements throughout a spool of fine wire. Highly reproducible results on clean and graphite coated tungsten and rnolybdenum wires from 1 to 9.5 mil are presented. A linear relation between resistance and wire weight (per standard length) was obtained on clean wires, but only on those coated wires with very uniform coatings. Results indicating a correlation between tensile strength, hardness, and resistivity are reported. THE increasing demand for greater uniformity in fine tungsten and molybdenum wires destined for use as mandrels, grids, and coils in radio tubes and as filaments in light bulbs has rendered inadequate the standard (sampling) approach to the control of wire diameter and other physical properties. This ap-

Jan 1, 1961

By A. Filyk

The current plant practice at Molycorp, Inc., Questa Division, a molybdenum producer in northern New Mexico, is described. An outline of crushing, grinding, flotation, drying, and tailings disposal is included, with emphasis on metallurgy.

Jan 1, 1976

By P. A. Beck

In the course of work on grain growth in high purity aluminum a simple optical method was developed for detecting the presence or absence of preferred orientation in annealed specimens. The specimens were prepared by grinding, polishing and "deep etching." The etching reagent used for high purity aluminum has been described.* The resulting etch pits produced selective

Jan 1, 1949

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity-clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 1, 1986

By D. J. Carney, J. Chipman, N. J. Grant

G. Derge—With the development of this last weapon, there is not much of a chance for hydrogen. It is certainly a very interesting paper, and it gives us more confidence in sampling liquid steel for hydrogen than we have ever had before. This satisfactory work gives considerable confidence to all of the chilled methods of sampling which should be more or less successful depending upon the degree of chilling obtained. J. T. MacKenzie—How do you handle a nonmagnetic specimen in that device? D. J. Carney (authors' reply)—I left that out in going over the analytical procedure. For the 18-8 steel, what was done was to get some iron wire which was degassed. One turn of wire was made around the sample; it was inserted into the analytical apparatus, and that was enough to allow the magnet to pull the sample and drop it in the furnace. Other methods could be devised for this apparatus to do the same thing. This was just a quick method. C. E. Sims—This method of sampling and analysis is very ingenious, and the results obtained attest to a satisfactory degree of accuracy. It was noted in the paper that the samples are satisfactory only when there is a complete absence of pipe. This should be empha- sized, particularly in view of the fact that they are cut off under water. Some reservations are held in regard to the adequacy of the method of sample storage prior to analysis. Cooling on dry ice undoubtedly slows down the rate of diffusion to a marked degree, and it obviously suffices when the analysis is made within a few hours. All of the samples, except some of high-nickel steels, were analyzed within 12 hr. It is still unknown how long this method would be safe. In the work at Battelle Institute, it was impracticable always to start analysis within 12 hr for various reasons. Some samples did not reach the laboratory for several days, and some were held as long as a month before analysis. During this period, they were held over mercury, and the gas evolved at room temperature was collected and analyzed. It should be mentioned that both the mercury and the container must be kept very clean.

Jan 1, 1951