Search Documents

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

Abbott, Argyle Campbell 1209 Sherwin Ave., Chicago, Ill. Almstrom, Adne A., Student, Met. Engrg., Washington State College Pullman, Wash. Ankudinoff, N., School of Mines, Univ. of Utah Salt Lake Cite, Utah. Apter, Robert F., Student, McGill Univ Montreal, Que., Canada. Bailey, Donald G 798 Kensington Rd., Los Angeles, Cal. Baker, Kenneth B., Met., Aluminum Co. of America Pittsburgh, Pa. Barger, Thomas, Student, Univ. of North Dakota Grand Forks, N. D. Bartholomees, Geo. C Box 304, Bonne Terre, Mo. Bates, Walter, Student, Univ. of Utah, School of Mines Salt Lake Cite, Utah. Bobb, Russell V 16 College Ave., Houghton, Mich. Boswell, John C., Stripping Asst., Fairbanks Exploration Co Fairbanks, Alaska. Brandenburg, E. C., Student, Univ. of Kentucky 112 Church St., Lexington, Ky. Brannen, John, Chemist, Assay Office, Consolidated Min. & Smelt. Co. of Canada, Ltd., Tadanac, B. C., Canada. Brooker, Edgar, Jr., Student, Ferrous Met., Stanford Univ., Stanford University, Cal. Brooking, Leslie E 738 Lakoma, Norman, Okla. Clark, Martin Lester, Student, Missouri School of Mines Rolla, Mo. Collins, Edward D., Jr Box 1597, Ribbing, Minn. Comeau, Faye Bernard, Student, New Mexico State School of Mines Socorro, N. M. Conder, Henry S., Student, Pet. Engrg., College of Min., Univ. of California, Berkeley, Cal. Cotton, John Francis, Metallographist, Stealton Plant, Bethlehem Steel Corp., Steelton. Pa. Dahlgren, Elmer George, Student, Univ. of Wisconsin, Tripp Hall, Madison, Wis. Dale, James L., Student, Colorado School of Mines Golden, Colo. Dashti, Mirza Abdullah Khan, Graduate Student, Columbia School of Mines, Engrg. Chemistry, New York, N. Y. DeHuff, Gilbert L., Jr., Student, Lehigh Univ Bethlehem, Pa. de Romana, Enrique P., Jr. Engr Casilla 22, Arequipa, Peru. Oresbach, Charles Howard, Geol., Gulf Production Co Box 1428, Amarillo, Tex. Evens, Howard G., Student, Michigan College of Min. & Tech Houghton. Mich. Fassler, Glen Emerson Rodman, Inspiration, Ariz. Feight, Charles Donald, Foreman, Clairton By-Product Coke Wks., Carnegie Steel Co., 319 5th St., Wilson, Pa. Floe, Carl F., Student, State College of Washington Pullman, Wash. Fuentes, Vicente, Student, Pet. Engrg., Univ. of Oklahoma, School of Mines, Norman, Okla. Fuhrman, Carl F., Student, New Mexico School of Mines Socorro, N. M. Goergen, Gerald G., Cerro de Pasco Copper Corp Casapalca, Peru. Grove, Hubert A., Training Course, U. S. Aluminum Co New Kensington, Pa. Gastetter, Robert E 1010 N. Cherry Ave., Tucson, Ariz. Halbouty, M. T., Student, Texas Agriculturcl & Mech. College, Box 254, Faculty Exchange, College Station, Tex. Halfast, Edgar 710 E. Okmulgee Ave., Muskogee, Okla. Hall, Robert Lee 121 58th St., Niagara Falls, N. Y. Hanson, Rolf H., Student, Colorado School of Mines Golden, Colo. Hillyer. Shaler G., Student, New Mexico School of Mines Socorro, N. M. Hoertel, Frederick W., Met., R. W. Hunt Co., Engrs St. Louis, Mo. Holtz, Henry G., Student, Ohio State Univ Columbus, Ohio. Hon, Richard J Box 721, Miami, Ariz. Huffman, James O'Neil, Student, College of Min., Univ. of California Berkeley, Cal.

Jan 1, 1929

By Henry J. Sandri

ACQUISITION JUSTIFICATION There are many reasons why companies consider acquisitions as a means to expand their operations. Some wish to reduce the impact of business cycles on their businesses. Others seek firms within the same industry for expansion and increased market share. Still others diversify in order to avoid takeovers. Whatever the reasons or justification, an evaluation of an acquisition candidate should be systematic and thorough. To many financial managers the concept of a systematic acquisition evaluation indicates the need for a regular set of evaluation criteria. While these are available from numerous sources, one basic parameter frequently overlooked is the application of these criteria to an industry which is different from the acquirer. This becomes particularly important when evaluating firms within the mineral industry. The mineral industry is significantly different from other industries to require different valuing techniques. • This paper will present a number of reasons why an acquisition candidate in the mineral industry should be evaluated differently from other acquisitions, including by other mineral firms. Additionally, this paper will review the most appropriate means of valuing a mineral firm. • Firms considering the acquisition of a mineral firm should understand the nature of the industry before ever making a tender offer. Some of the general considerations include the following: • Level of Capital Intensity: In the mid-1980's the start up cost for a gold mine has been between 20-200 million dollars and 500-1,500 million dollars for a bauxite operation. • Global Nature of Competition: Except for certain industrial minerals, most minerals and metals are traded worldwide and many on national exchanges, such as COMEX. • Start-Up Time: Many mining operations in developed and developing countries have long lead times, 7 to 10 years in some cases, prior to the start-up of production. • Long Term Nature of Investment: For most mineral operations payback usually occurs at least 7 years after production has started. Additionally, many mining operations will continue producing for 80-100 years. • High Level of Risk: The number of factors that a mining firm cannot control such as grade, volume, world supply and demand, plus the long payback periods tend to classify mineral firms at a higher than average risk compared to other investments. • Cyclical Nature: The mineral industry is cyclical in nature, experiencing long troughs and explosive peaks, thus making timing a critical issue. • Labor Intensive: Even with the large capital requirements needed to operate a mine, most mines are labor intensive in proportion to their capital equipment. • Location: Obviously, the nature of this industry requires operators to work in difficult locations, frequently far from civilized localities, in poor weather conditions and without proper supply and distribution infrastructure. One of the most important considerations is an understanding of asset replacement and asset value. Unlike manufacturing concerns, firms in the mineral industry are working toward the elimination, through depletion, of their asset base. Product flexibility is not available to a mining operation. A mineral firm basically has two options as its resource base is depleted: 1) replace the asset with new production, or 2) deplete the asset and close down operation, as in the South African gold mining model referred to later in this paper. An understanding of the

Jan 1, 1985

By R. Silverman, H. Blumenthal

It was found that despite the similarity of chemical analyses of different titanium carbides used as base materials for cermets, the physical properties, especially transverse-rupture strengths, of test bars were different. Hence this metallographic study attempts to link physical properties to micro-structures. It is shown that microstructure, grain shape, and grain growth are functions of three interrelated factors: 1—powder production procedure, 2—surface conditioning of the particles, and 3—impurities either contained in the original powder or acquired during ball milling. An explanation is offered for the "coring effect," long observed, but heretofore of unknown origin. The explanation is based on assumption of an oxide film and on chemical analyses which substantiate these findings. TITANIUM carbide has become in recent years a material of great interest in the high temperature field. Consequently, many manufacturers in the United States and Europe are producing titanium carbide for cermet applications as well as for additions to the well known tungsten carbide tools. All present commercial processes of titanium carbide production utilize the chemical reaction of titanium dioxide and carbon to form as nearly as possible stoichiometric Tic. This reaction is carried out in three ways: 1—in a menstruum of molten metal,' 2—in the solid state, either in a protective atmosphere2 or in vacuum;" or 3—in an are-melting operation. In spite of the fact that the pure carbides obtained in these operations are almost identical chemically, the physical properties vary considerably when they are combined with a binder (Ni, Co) to form cermets. This fact led the authors to examine metal-lographically nickel-bonded titanium carbide in order to find the possible reasons for this behavior. Materials and Methods Five different titanium carbides were used in this investigation. They are identified in Table I. The first four materials were used in the as-received condition. Material E, received in lumps, was crushed to —100 mesh and carried through a flotation process in order to bring its graphite content in line with the other products. A Galagher flotation cell was used with pine oil as frothing agent. The chemical analyses of the investigated materials are given in Table 11. The binder used was carbonyl nickel of 9 to 14 microns particle size, supplied by A. D. Mackay. The materials were ball milled at a ball to charge ratio of 6:1 using procedures described under "Experiments and Results." All particle sizes mentioned are averages determined with a Fisher Sub-sieve Sizer. Test bars (lx0.40x0.16 in.) were prepared by 1—hot pressing to 85 to 95 pct of theoretical density at pressures between 1 and 1½ tsi and temperatures from 1600" to 1800°C, 2-—-cold presssing after 3 pct camphor had been added, or 3—wet pressing, both 2 and 3 at pressures between 5 and 10 tsi. All pressed bars were sintered in a vacuum of 105 to 10-6 mm Hg for 2 hr at 1350 °C. Transverse-rupture strengths were determined by breaking on a Baldwin Universal Testing Machine over a 9/16 in. span. Densities were measured by water displacement. The preparation of the specimens for micrographs was done according to Silverman and Doshna Luscz." All magnifications are at X1000. A sodium picrate electrolytic etch was used. Experiments and Results The influence of ball-milling procedure, ball-milling medium, pressing procedure, and sintering procedure on the microstructure of 80/20 — TiC/Ni were investigated. Ball Milling of Materials A, B, and C in a Steel Mill: Figs. 1 and 2 show microstructures of hot-pressed and vacuum-sintered test bars of materials A and B after the respective materials had been ball milled to 2.1 microns particle size in a steel mill and mixed with 20 pct Ni binder. Material A (Fig. 1) shows considerable grain growth. Also evident is a tendency of the carbide grains to coalesce. The density is 98 pct and the low transverse-rupture strength of 111,000 psi is probably caused by many large grains and an unfavorable packing factor. Almost all grains show a slight indication of "coring." Material B (Fig. 2), although showing grain growth, still has many small particles and a better distribution of binder and carbide due to the relative absence of the coalescing tendency. "Coring" can be observed in almost all grains. The high transverse-rupture strength of 179,000 psi and the density of 100 pct are believed to be due to the many small grains completely surrounded by the binder phase. There is also a preference to form spherical grains with material A, while most grains of material B preserve their angular shapes. Material C, of which no picture is given, stays between A and B in every respect. Rounding of some grains can be observed as well as coring, but the latter to a lesser degree than with material B. Its densification is good and the transverse-rupture strength obtained is 142,000 psi. Ball Milling of Materials A, B, C, and E in a WC Mill: When the Tic powders were ball milled to 2 microns particle size in a we mill, then ball-mill mixed with 20 pct Ni binder, hot pressed, and vacuum

Jan 1, 1956

By E. T. Turkdogan, L. S. Darken

Using the quadratic formalism, thermodynamic equations are derived for the composition dependence of the heat and entropy of mixing. The applicability of these equations is confirmed by available experimental data on the activities and heats of mixing for binary metallic systems of Group ZZB elements. In a recent paper arkeen' introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. That is, in the terminal region, which may extend to as much as 60 at. pct, the logarithm of the activity coefficient, log y,, of component 2 is a linear function of (1 - N,)' where N2 is the atom fraction of component 2. Similarly, for the other component, log yl is a linear function of (1 - N,)'. A number of iron-base binary liquid alloys were shown to obey this quadratic formalism. arkeen' extended this formalism also to any corner of a ternary system and showed that the activity coefficients of the components 1, 2 and 3 (1 is taken as the solvent) can be represented by quadratic terms involving five parameters, four of the binaries and one for the ternary system. Numerous examples given by arkeen' demonstrated the general applicability of the quadratic formalism to iron-base systems over a wide composition range. In this paper further examples are given of binary liquid systems (Group IIB elements, Zn, Cd, and Hg) and of several solid solutions, again demonstrating the appropriateness of this concept. A further purpose of this paper is to extend the quadratic formalism to the enthalpy and excess entropy of binary metallic solutions and to test the equations so found using available experimental data. QUADRATIC FORMALISM FOR HEATS AND ENTROPIES OF MIXING OF BINARY METALLIC SOLUTIONS The following equations, reproduced from Darken's paper, are for the two terminal regions of binary systems. at infinite dilution and a's are temperature dependent parameters to be determined from the experimental data. Although the quadratic formalism is an assumed representation of the data, Eqs. [I] to [4] are thermo-dynamically consistent with the Gibbs-Duhem relation and satisfy Raoult's and Henry's laws as limiting cases. As pointed out previously,' the following form of the Gibbs-Duhem equation facilitates the integration in general but particularly in regions I and 11, where each of the derivatives is constant. The partial molar enthalpy of solution i, (and i; the value of i, at infinite dilution) are related to the activity coefficients y, and y," by the thermodynamic relation Differentiating Eq. [l ] with respect to 1/T and substituting the above thermodynamic relation gives for region (I) It is reasonable to assume that over a temperature range of experimental interest, the enthalpy of mixing is essentially independent of temperature, implying from Eq. [7] that the derivative da,,/d(l/) is also independent of temperature. On the basis of this argument, the temperature dependence of a has the form where £ and S have the units of enthalpy and entropy respectively; they are characteristic parameters for a terminal region of a binary system, e.g. for region (I), C12, S12 and for region (II), d:,,, S2,. Using this equation gives for dff ,/ d(l/), From Eqs. [7] and [9] an expre_ssion is obtained for the composition dependence of L,. Similar calculations are made for El and the results are summarized below for the two terminal regions. For region (I), The corresponding expressions for the molar heat of solution, AHM, are readily obtained from the above equations for the two terminal regions: For region (I),

Jan 1, 1969

By Charles H. Moore, H. Sigurdson

When lime and magnesia are used as fluxes in the smelting of titaniferous ores fluid, digestible slags low in iron oxide and high in titanium dioxide are produced. The mineral phases present in such slags are (Fe,Mg)O.ZTiOp, CaTiO3, and minor amounts of silicate glass (or its devitrification products). The flux additions are added to the ore in relative amounts to crystallize a ratio of (Fe,Mg)O.2TiO2 to CaTiO, of near the eutectic proportions of 60 pct (Fe,Mg)O.2TiO2 and 40 pct CaTiOl. FeO.TiOz (ilmenite) remains present in the slag until the FeO content is reduced to approximately 8 pct. Optimum slag composition is obtained by reducing the FeO content to between 2 and 6 pct. Continued reduction shifts the (Fe,Mg)O.2TiO2 to oxygen deficient structures classified as MgTi306 and MgTi2O.. Further reduction yields titanium oxycarbides and freezes the melts. The(Fe,Mg)0.2TiO2 structure shows a complete isomorphous replacement of iron by magnesium. It also forms a solid solution compound with as high as 12 mols of TiO2 under reducing conditions without the occurrence of rutile or reduced titanium oxides in the slag.

Jan 1, 1950

The old De Beers mine, which lies northwest of Dutoitspan mine at Kimberley, was the mine which launched Cecil Rhodes (In his historical career. It was the nucleus of the De Beers Mining Co. Ltd., formed in 1880, which later became De Beers Consolidated Mines Ltd. Inactive for more than a half century, the De Beers Mine is being rejuvenated for a new era of operations. Both mines were on the Vooruitzicht farm owned by the De Beers brothers, who had bought it from the Orange Free State Government ten years previously for £50. Although the brothers sold it soon after the discovery of diamonds at Dutoitspan, they are remembered for having given their name to the foremost diamond mining company in the world. Diamonds worth nearly R180,000,000 have come from this ground, and more will be recovered when the mine is re-opened.

Jan 9, 1963

By Edwin H. Olson, Morton Smutz, Charles J. Baroch

IN 1949 an orebody containing some 10 billion lb of recoverable rare earth metals was discovered in the Mountain Pass district of San Bernardino County, California.1 The following year Molybdenum Corp. of America purchased a number of claims at the deposit and a mill on the property which had been constructed to process the district's gold ores. Average composition of ore from the San Bernardino deposit is less than 0.1 pct ThO2, 25 to 35 pet calcite, 10 pet rare earth oxides, 15 to 20 pet silica, and 30 to 40 pet barite.2 Rare earth content of the ore analyzes 50.7 pet CeO2, 4.2 pet Pr6O11, 11.7 pet Nd2O3, 1.3 pet Sm2O3, and 34.3 pet La2O3, and others.2

Jan 3, 1959

By E. B. Ekren, F. C. Frischknecht

Recently released results of surveys employing the slingram and turam methods show the applicability of electrornagnetics in mapping new areas containing both oxidized and unoxidized iron in the Lake Superior region.

Jan 10, 1961

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By H. C. Casey, M. B. Panish

The roles of the phase diagram and the diffusion and solubility analyses in the selection of sources for the diffusion of zinc into GaAs are discussed. Isothermal sections of- the phase diagram are described at 1000°, 775°, 744°, and 700°. Below 744° the three solid phases, Zn3As2, GaAs, and ZnAsz, may be in equilibrium. In the composition regions where the three solid phases are in equilibrium, the partial pressures of the components do not vary with composition and there is no liquid phase. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected to yield reproducible diffusion profiles without surface damage. The 5/50/45 ternary source Provides a significant improvement in the reproducibility and planarity of- the zinc diffusion as compared with other zinc diffusion sources that result from starting with elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. Several experimental diffision profiles for the 5/50/45 diffusion source have been determined. The profiles are very steep in the region of the junction and produce devices that exhibit step junction behavior. The junction depth varies as the square root of time. Diffusion at 700°C for 4 hr gives a 5-µ junction depth and a surface concentration of 2.4 x1020 cm-3. The surface concentration is enhanced by a factor of three and the junction depth decreased by a factor of ten as compared with diffusion with a starting source 01- elemental zinc. The differences in dijyusion behavior with these two sources are due primarily to the approximately 10' greater equilibrium As4 partial pressure for the 5/50/45 source. ThE most common technique for the preparation of GaAs p-n junctions for diverse applications ranging from switching diodes to injection lasers has been to diffuse zinc into the solid from the vapor phase. The zinc impurity has generally been provided by introducing into a diffusion ampoule elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. For the purpose of eliminating surface deterioration, zinc has been diffused into GaAs through SiO2 films1 and from zinc-doped SiO2 films.2 During a study of the injection and recombination mechanisms in GaAs junctions, we found that these diffusion techniques either resulted in nonreproducible diffusion profiles and nonplanar junction interfaces or were extremely inconvenient to use. An unpublished report by Allen and pearson3 emphasized that an understanding of diffusion requires relating the diffusion conditions and system compositions to the ternary phase diagram. Recent studies have made it possible to relate the effect of starting source composition on the GaAs sample surface and diffusion profile reproducibility and, in addition, to estimate the expected surface concentration and zinc diffusivity. These studies include the Ga-As-Zn phase diagram,415 the determination of the incorporation reaction for zinc as a substitutional impurity,6 and the analysis of the concentration dependence of the diffusion coefficient.' In this paper the role of the phase diagram in the selection of the starting diffusion source composition is illustrated, and an application of the diffusion and solubility analyses is used to demonstrate their utility in the estimation of surface concentration and diffusivity for various starting source compositions. Consideration of the isothermal sections of the ternary phase diagram shows that below about 744° C a composition region exists where the three solid phases Zn3As2, GaAs, and ZnAs2 are in equilibrium without a liquid phase. In this region the partial pressures of the components do not vary with composition, and thus the surface concentration and diffusivity depend only on temperature. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected. As will be described in detail, this diffusion source yields reproducible diffusion profiles without surface damage, planar junction interfaces, and steep profiles that result in devices with step junction behavior. Only closed diffusion systems are considered. Open or flowing vapor systems require the maintaining of constant vapor pressures in the flowing gas and represent control problems outside the scope of this discussion.

Jan 1, 1969

PRESIDENT AND DIRECTOR SCOTT TURNER WASHINGTON, D. C. PAST PRESIDENTS AND DIRECTORS WILLIAM H. BASSETT WATERBURY, CONN. ROBERT E. TALLY JEROME, ARIZ. TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y.

Jan 1, 1932

By W. P. Blake

Wm. P. Blake, New Haven, Conn. (Communication to the Secretary, June, 1889): It is gratifying to find that Prof. Carpenter in his paper sustains the accuracy of my original determination of

Jan 1, 1889

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By J. D. Braun, C. W. Powell

Diffusion between gold and indium at two temperatures below the melting point of indium (155.4oC) was investigated. The major, component of the diffusion zone was determined to be AuIn2; the other, intermediate phases in the system occur in much narrower layers In order of decreasing layer width these are: Au9In4, AuIn, Au4In. Inter diffusion coefficients of the four intermediate phases and the terminal solid solutions lie in the range of 2.4 x 10-l3 to 1.8 x 10-11 sq cm per sec. WHEN two metals which do not form a continuous series of solid solutions interdiffuse, each phase in equilibrium at the diffusion temperature should appear as a separate layer in the diffusion zone. In the Au-In system, diffusion plays a significant part in many commercial applications, particularly where indium alloys are used as solders for electrical contacts with very fine gold wire, for estab- lishing electrical contact to thin metallic films, and for mounting metal-coated piezoelectric crystals. A knowledge of the number, extent, and type of phases which form at diffusion temperatures below the melting point of indium, 155.4oC,1 and the diffusion constants for the system would be useful for these practical applications. Of more basic significance, additional information on polyphase diffusion in a system not previously investigated would be gained. The phase relationships in the Au-In system were determined primarily by Kubaschewski and Weibke1 and are based on thermal, microscopic, and X-ray analysis, Fig. 1. There are five intermediate phases in the system having approximate compositions corresponding to the formulas: Au4ln (ß)—80.0 at. pet Au; Au3In (?)— 75.0 at. pet Au; Au9In4 (d)—69.2 at. pet Au; AuIn—50.0 at. pet Au; AuIn2—33.3 at. pet Au. Solid solubility of indium in gold at 700°C is reported as 12.64 at. pet and at 406°C as 10.36 at. pet. No solid solubility of gold in indium is reported.

Jan 1, 1964

By G. R. St. Pierre, A. Ghosh

In the Si-C-0 system at temperatures of interest in process metallurgy there are four stable condensed phases—silicon, carbon, silica, and silicon carbide (Sic). Silicon melts at 1683oK1 and shows negligible solubility for carbon and oxygen at 1700°K. However, silicon dissolves approximately 1.5 at. pct C at 2500oK.2 Carbon in the form of graphite remains pure and dissolves negligible amount of silicon.' Silica (crysto-balite) melts at 2001°K' and is essentially a stoichio-metric compound. Silicon carbide is a solid and shows negligible deviation from stoichiometry up to approximately 2800oK.2 Besides the condensed phases there is a gas phase

Jan 1, 1970

By J. M. Snook, F. C. Langenberg

FOR a better understanding of the melting and refining processes, the oxygen content of the steel bath should be determined. The oxygen content influences many process and product variables such as the efficiency of alloy recoveries, the ingot structure (through reaction with carbon in the steel), certain reaction rates, cleanliness (formation of indigenous oxide inclusions), and mechanical properties. Many methods of sampling liquid steel for oxygen have been devised. These methods can be divided into two main groups: 1) taking samples directly in the furnace or ladle;'-'0 2) removing the metal from the furnace or ladle in a sampling spoon and pouring it into a mold, or drawing the metal from the spoon into a sample holder.11-l4 The advantages and disadvantages of the two general sampling methods are presented in Table I. The bomb-sampling technique described by Huff, Bailey, and Richards8 has been used by the Crucible Steel Co. in certain research projects where oxygen contents were needed. It was recognized that a localized boiling condition could result when the mold is introduced into the steel bath, although the work of Gilbert and Bailey9 seems to indicate that the carbon boil occurring in the bomb-sampler cavity has a negligible effect on the oxygen content. In order to confirm the reported negligible effect of a carbon boil, additional work was done with adaptations of the conventional bomb sampler. The methods used are shown in Fig. 1 and are as follows: 1) Type A: aluminum wire (0.125-in. diam) coil in cavity; steel cap over mouth 2) Type B: aluminum cup in cavity; aluminum cap over mouth, 3) Type C: aluminum cup in cavity; steel cap over mouth, 4) Type D: fine aluminum wire (0.013-in. diam) in cavity; steel cap over mouth. The amount of aluminum wire in the Type A and D samples varied from 0.8 to 1.2 pct of the sample weight. The aluminum cups averaged 2.0 pct of the sample weight; the latter were used to ensure that the steel contacting the walls of the bomb cavity was fully killed. Samples were taken from plain carbon heats made in open-hearth furnaces. This grade of steel before silicon additions is essentially an Fe-C alloy and the effects of other alloying elements on the oxygen activity can be neglected. The results of sampling with the bomb samplers is shown in Fig. 2 where the percent oxygen is plotted against the percent carbon on log-log paper. Spoon sample results on the same grade of steel where the sample was killed in the spoon are shown in Fig. 3. The oxygen contents were determined by the vacuum fusion method. A comparison of Figs. 2 and 3 shows that the oxygen concentrations obtained with the spoon-sampling method (metal killed in the spoon after slag removed

Jan 1, 1960

SAFETY in open-pit mining receives a minimum of notoriety, but its significance in profitable and efficient operation is as great as in other methods of mining. Open-pit operators from Arizona, New Mexico, and Mexico, exchanging ideas on safety at a symposium during the recent annual meeting of the Arizona Section, AIME, discovered unanimity of opinion that the successful safety program depended on managerial and supervisory support with the vigorous cooperation of the employes. Safety Organization The operation of a safety program is dependent on the ability of management to project enthusiasm through the company organization. This requires a suitable method of communication to the supervisory and employee levels so as to approach them in a manner that will inspire cooperation. Safety committees comprised of various combinations of managerial, supervisory, and employe personnel are frequently used for this purpose. The open-cut mine of the Chino Division of the Kennecott Copper Corp., Santa Rita, N. Mex., operates its program through management, a full-time safety engineer, and two safety committees, the Departmental and Shops Safety Committee and the Central Safety Committee. The Departmental and Shops Committee consists of one employe from each department and shop and the safety engineer. The selected members serve for a period of one month. This committee meets once a month, the only representative of management being the safety engineer because it is believed that employes will speak more freely when their supervisors are not present. The duties of the committee are to report hazardous conditions and make recommendations, but the committee has no authority to approve or disapprove. The Central Safety Committee is comprised of supervisory personnel from all departments and shops, and one member of each of the five bargaining organizations. Members of this committee are permanent and hold meetings soon after the departmental group to take action on recommendations of the latter. The committee system insures participation of all levels of personnel in the accident-prevention program, thereby stimulating safety consciousness. The New Cornelia branch of the Phelps-Dodge Corp., uses three groups to conduct the safety program; the General Safety Committee, Division Safety Committee, and the operating-unit safety meetings. The unit safety meetings provide for active participation of employes in discussion of various phases of the program. Within these groups vigorous opinions regarding safety are often expressed and the workmen are critical if they recognize a digression from the adopted safe-practice procedures. These monthly discussions give the program vitality. The Division Safety Committee is composed of the division superintendent and the division department heads, and follows an established pattern in discussion of all phases of the safety program. The General Safety Committee, made up of the manager, division, and department heads, makes decisions on policies and procedures; it renders decisions on recommendations and suggestions. Management at the New Cornelia branch feels this system of safety committees and meetings has been active in advancing the program. Safety Codes In the open-pit mines of the Southwest, a safety code for operation or service of equipment, methods

Jan 1, 1952

By C. R. Clark, G. Swift, D. S. Roberts

The purpose of this investigation was to measure PVT behavior of various types and combinations of heavy hydrocarbon components from the paraffinic, naphthenic and aromatic classes where the relative proportions Of the various components were selected to approximate those of natural gas or gas condensate systems. Synthetic mixtures were used so that the compositions Of the various components could be measured accurately. n-Heptane, methylcyclohexane and methylbenzene were used to represent the paraffinic, naphthenic and aromatic components of the heavy fraction. In the mixtures studied, the heavy fraction composition was held constant at O. O5-mole lraction, the balance being methane except for one mixture where 0.10-mo1e fraction of an intermediate component, propane, was added. The PVT data for the mixtures were determined in a variable-volume, constant-mass apparatus at psuedo-reducedtemperatures from 1.84 to 2.00, over a pseudo-reduced pressure range from 2.3 to 12.0. The experimental results showed that, regardless of the type of heavy material (paraffinic, naphthenic, aromatic, or combinations thereof) mixed with methane or methane and propane, the compressibility factors at equal values of pseudo-reduced temperature and pressure varied by less than 2.2 percent. INTRODUCTION PVT data is used for natural gas and gas condensate fluids in determining reserves of reservoirs and performance of wells, in metering produced fluids, and in recombining samples for laboratory studies. While there are vast amounts of PVT data reported for natural gas and gas condensate systems from which useful correlations have been developed, ' the compositional analyses for these systems and the resultant correlations typically were made with components analyzed through some arbitrary carbon number, usually C6, with the residue reported as a lumped "heavy" fraction. The heavy fraction was stoichiometrically recombined on the basis of an apparent molecular weight to give the final compositional analysis. It is virtually impossible to make a systematic analysis of the effect that variation of the relative amounts of paraffinic, naphthenic and aromatic constituents of the heavy fraction of natural systems might have on PVT behavior. Because there is considerable latitude in the relative amounts of these constituents, one speaks of crudes or condensate liquids as being "paraffin base", etc. It is of interest to determine if changes in the relative amounts of these three types of hydrocarbons in the heavy fraction cause significant changes in PVT behavior. If so, steps should be taken to describe better the nature of the heavy fraction in PVT correlations. If not, more confidence can be placed in the correlations presently employed. DESIGN OF THE EXPERIMENTAL INVESTIGATION We attempted to determine if changes in the base of the heavy fraction would cause significant changes in the PVT behavior of gas or gas condensate fluids. Synthetic mixtures were used to enable us to systematically vary the base of the heavy fraction and to analyze accurately the fluids. We found that the heavy fraction of naturally occurring condensate systems seldom exceeds 0.05-mole fraction. Thus, the mole fraction of the heavy fraction in the synthetic systems studied was set arbitrarily at 0.05, to maximize whatever deviations in PVT behavior that might occur. Further, we judged that since the C7 hydrocarbons normally are present in greater quantities than higher carbon number hydrocarbons in naturally occurring systems, the use of n-heptane, methyl cyclohexane, and methylbenzene to represent the paraffinic, naphthenic, and aromatic species in the heavy fraction would be most appropriate. Finally, to enable us to compare our

Jan 1, 1970

By D. C. Porterfield

-4s a result of world economic conditions brought about by the European war and the consequent loss of European markets for Venezuelan crude, production in Venezuela decreased from 205,433,000 bbl. in 1939 to 186,134,000 bbl. in 1940, or 9.4 per cent. This decline interrupted a steady annual increase in production from the country, which had been continuous since 1932. The Maracaibo Lake Basin in western Venezuela accounted for 135,738,000 bbl. during 1940, or 73 per cent of the total, as against eastern Venezuela's production of 50,396,000 bbl., or 27 per cent of the total for the country. Corresponding figures for 1939 were 167,688,000 bbl., or 82 per cent of the total from the Lake Basin, and 37,744,000 bbl., or 18 per cent from the east. These comparisons indicate the increasing importance of the newer developments in eastern Venezuela, but it is unlikely that production from the east will ever exceed that from the west. In all, 429 new wells were completed in Venezuela during 1940 as compared to 438 in 1939. Of the 1940 completions, 411 were in proved areas and 18 were wildcats; 389 (95 per cent) of the exploitation wells drilled were producers, I was a gas well and 21 were dry holes, while 6 (33 per cent) of the wildcats drilled were producers and 12 (67 per cent) were dry; 263 of the exploitation wells and 4 of the wildcats were in the Maracaibo Lake Basin and 148 exploitation wells and 14 wildcats were in the east, mostly in the State of Anzoategui. Exploration of the light-oil areas in the Tia Juana and Lagunillas fields was con- tinued during the year with favorable results. Along the lake shore, drilling was confined principally to fill-in wells in the La Kosa, Tia Juana, Laguni!las and Bachaquero fields, although some important semi-exploratory drilling was done in the Pueblo Viejo area between Lagunillas and Bachaquero fields. The only other developments of particular interest in the west were the successful completion of a step-out well lying to the south of the former southern limit of Mene Grande field, which adds considerable proved acreage to that field; and the failure of two wildcats that were drilled near the Colombian border to determine whether the productive sands of the Petrolea field in the Barco Concession, Colombia, extend into Venezuelan territory. In the east no new fields were discovered during the year, although five wildcats were completed as producers. Three of these, Guario No. I, Jusepin-56 and LM-I (Leona), discovered important extensions to previously proved areas and the remaining two, Cantos-I and SPN-I (Socororo), were subsequently proved to have tapped productive sands of small extent and operations in these areas have been suspended. The greatest activity in the east was concentrated in the Oficina field, where 105 new wells were completed during the year and production was increased from 22,540 bbl. per day during January 1940 to 57,627 bbl. per day during December 1940. Important development work was also done in the Jusepin. San Joaquin and El Koble fields.

Jan 1, 1941