Search Documents

[ ]

Jan 1, 1938

By Frank Firmstone

IN April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Fig's. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised to¬gether, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places. * Etudes our lea Haut Fourneaux, page 108.

Jan 1, 1874

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By Frank Firmstone

In 1871, two furnaces at the Glendon Iron Works, which had been blown out on account of the "coal strike," were altered from the open-top plan with side flues for collecting the gas, to closed tops with cup and cone. In one furnace the suppression of the side flues permitted a considerable alteration in the profile, but in the other (No. 5) no change in this respect was made; the side flues were simply bricked up and new ones cut through the sides close to the top. This furnace was in blast over four years, and we can, therefore, form a pretty good idea of the effect of the alterations on the furnace process. The principal dimensions are; Height 72'; greatest diameter, 18'; diameter at tuyeres, 8'; diameter of top, 10'; diameter at stock line (point at which the top of the materials is kept), 11'; cubic contents, 11,900 cubic feet. The table below shows the average results for periods of twentysix weeks each. 1st, of the open-topped furnace; 2d, of the furnace with the first charger used, which was an ordinary cup and cone (diameter of cone 5' 2") 3d, with the charger used ever since, a " double " cone 7' 5" diameter outside, having a central opening 3' in diameter. The diagram (Plate 11) shows the daily variations, in the grade of the irons for the same periods.*

By Thomas T. Read

EVERYONE engaged in the teaching of mining engineering will, I suppose, agree that the most difficult subject to teach is "Mining Methods." One primary difficulty is that the students taking the course have either had no previous experience in mining, or else they have had; either seeming to be somewhat of a drawback. The students who are unfamiliar with mines find it difficult to visualize underground conditions, as described and illustrated with sketches and maps, while those who have had underground experience seem to 'find it difficult to visualize anything much different from that which they have already seen. This reminds one of the remark about the Presbyterian doctrine of predestination, to the effect that "you are damned ,if you do; and damned if you don't."

Jan 1, 1930

By Hollis Peacock

THE Bingham area in the West Mountain mining district on the eastern slope of the Oquirrh range, some 28 miles southwest of Salt Lake City, has been the most consistent producer for the United States Smelting Refining and Mining Company, production having been continuous, except for minor interruptions, since the organization of the United States Mining Co. in 1899. This production has come from fissures and mantos largely within limestone members aggregating something less than 10 per cent of a thick quartzite sequence of Pennsylvanian age which has been warped into an open syncline plunging northwesterly. Bedding on the easterly limb dips 10°-45° but steep-ens to 90° and even overturns on the westerly limb. Ore bodies cluster about the more northerly of two elongate interconnecting stocks of monzonite which have risen in an axial position within this syncline. Largely within the more northerly of these stocks is the low-grade copper ore body exploited in the Utah Copper open cut of the Kennecott Copper Corp. The values, in seams, minute fracture fillings, and disseminations of pyrite and silica, pervade not only the stock but adjacent sediments, and form a nebulous, sprawling mass which both mineralogically and geographically is the center of the district. The more southerly of the twin stocks appears to be comparatively inert and without obvious relation to mineralization. which

Jan 1, 1948

By Reaves. M. J.

The title of my talk, "What Happened to the Uranium Boom?" is old news. Certainly it is for this group. All of us that make our living in uranium know that the boom of the last half of the 1970's is over. U.S. production has been exceeding consumption by more than two to one. Mines and mills are closing and yellowcake prices have been dropping for over 20 months. The gloomy outlook for the industry in the near term has been well documented by soothsayers of various descriptions, your daily newspapers, and in the Nuexco Monthly Reports. I'd like to attempt to describe the next upturn in the market (speculate, really) based upon the clues we're seeing now. In order to do that, I'd first like to go over briefly, some of the market factors that contributed to the recent price drop and resultant production cutbacks, and then hypothesize on the way these factors are changing and will change. Market prices are greatly affected (maybe even entirely determined) by buyer perceptions. This is particularly true with uranium, because of the long lead times associated with nuclear plant construction and also with conventional mine/mill development. Before the price rise (say, 1975) utility uranium buyers believed that: 1) U.S. producers would have difficulty expanding to meet U.S. demand. 2) Australian and Canadian production was essential to avoid shortages in the early 1980's. 3) Uranlum prices would continue to rise as demand exceeded supply. 4) Enrichment capacity would become inadequate. It was thought necessary, therefore, to build enriched inventory in the early 1980's for use in the late 1980's. Artificially accelerated expansion of the uranium producer industry was necessary to accommodate anticipated enrichment demand. Current perceptions are largely the opposite. These are the beliefs that were held most of this year and late last year as prices dropped. 1) U.S. production is far in excess of domestic need. Contraction of the U.S. production lndustry is necessary. 2) Canadian and Australian supply is optional and not essential. Producers in those countries are expanding mainly by displacing higher cost production and not because they fill a void, 3) Prices may be essentially stable for some time. 4) Enriched uranium is in excess supply. That is 1981. 1982 is shaping up to look like this: 1) Prices will have bottomed out. (That is not Nuexco's opinion necessarily, by the way, but it is my opinion.) 2) There will still be substantial utility inventories, but fewer spot sales. 3) Canadian and perhaps Australian sellers will have made substantial sales in the U.S. and will be aggressively seeking more. 4) U.S. production will have been dramatically curtailed. U.S. utilities that wish to con- tract long term will have difficulty in finding domestic sellers. Concern will develop about the availability of U.S. production capability. Virtually all long term con- tracts signed will be with non-U.S. sellers. 5) An awareness will begin to develop among U.S. buyers that we are approaching a period of dependence upon foreign uranium (which will be true). The history of the uranium market has been one of dramatic changes and overreaction to those changes. The rapid price rise of a few years ago generated excess U.S. production capacity and the rapid price drop of the last two years will almost certainly result in too little capacity. It will soon be difficult for U.S. buyers to buy domestic material except on the spot market. The question is, "will they care?" The lack of demand, of course, is the underlying reason for the current poor health of the uranium industry. In 1972, 1973 and 1974 collectively, there were 105 nuclear reactors ordered in the U.S. That ordering rate was expected to continue and accelerate throughout this century. In 1975, 1976, 1977, 1978, 1979, and 1980 altogether, there were 56 more reactors cancelled than ordered. The net growth of our only customer since 1974 has been a negative 56. TO put this in perspective, if these 56 reactors were operating now it would more than double present U.S. uranium consumption. Underlying lack of demand is something that is simply not going to change in this decade. Time is going to be required. The NRC indicates that the maximum feasible number of new reactors that can be licensed each year is six. That would increase uranium consumption by only 10% per year. New reactors, if ordered tomorrow, would not generate new uranium demand until after 1990. Even so, United States' consumption of uranium will rise from the 1980 level of 18 million pounds per year, to

Jan 1, 1982

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By D. R. Pratt, R. W. Hanks

The method of Caldwell and Babbitt for detennining Bingham plastic rheological constants from engineering pipe flow data has been erroneously used in many previous applications. A reanalysis of extensive pipe flow data from the literature is performed. Critical Reynolds numbers corresponding to the laminar-turbulent transition calculated from these data are found to agree with theoretically calculated values for the entire flow range studied. Similar agreement is found for the authors&apos; own data&apos; for flow of 10 slurries between parallel plates. The Bingham plastic model is shown to be a reliable representation of the flow of non-Newtonian slurries provided it is properly applied. If the Hedstrom number He = pD2 t0/?2 > 104, then the linear approximation method of Caldwell and Babbitt is invalid for pipe flow data obtained in systems of ordinary engineering interest, and the complete nonlinear form of the pipe flow Bingham plastic equation must be used in determining rheological parameters. INTRODUCTION Many materials of engineering interest must be handled and transported as slurries or suspensions of insoluble particulate matter in a Newtonian liquid. These suspensions frequently exhibit non-Newtonian rheological behavior which is reasonably well described by the simple Bingham plastic rheological equation1 Using this particular equation to describe the laminar flow characteristics of slurries was discussed at length by Caldwell and Babbitt2-4 who considered the flow of various clay slurries and sewage sludges. The model has since been used by many others.5-7 More recently the problem of predicting the laminar turbulent transition Reynolds number for Bingham plastic fluids has been treated8 for the case of flow in pipes. This paper points out errors which have existed in the analysis of Bingham plastic flow since the work of Caldwell and Babbitt2-4 and presents a reanalysis of the laminar turbulent transition calculatiod for Bingham plastic flow in pipes. In addition, new data obtained for flow of Bingham plastic slurries between parallel plates, both in laminar flow and in the laminar turbulent transition region, will be presented and compared with the theoretical analysis of laminar turbulent transition for flow between parallel plates. THEORETICAL ANALYSIS PIPE FLOW The mathematical analysisl-4 of laminar flow of a Bingham plastic fluid leads to the following equation. where q = <v>/R is a pseudoshear rate, rw is the wall shear stress Eo = r0/rw, r0 is the yield stress and 1 is the coefficient of rigidity or plastic viscosity from Eq. 1. Caldwell and Babbitt2-4 recognized that the quartic term in Eq. 2 was small compared to the other terms whenever 5, « 1, and that for large values of 7, a plot of Eq. 2 becomes linear. The slope of such a plot with rw as ordinate is 4? and the intercept is (4/3) ro. This approximation is illustrated schematically in Fig. 1. The shaded region between the true curve and the straight-line approximation near the origin represents the contribution of the quartic term. In principle, therefore,

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is, relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.1 Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.2 Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general; development of the area was slow. To the south, the heavy. mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions.3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west. of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of-the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.2,3 The axis of the syncline dips to thee southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.4 Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary, band of secondary clays found intermittently, at points, across the, south of the province where glacial action did not disturb or remove them.8 In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to. 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.9 It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1952

By L. W. McKeehan

IT is no longer necessary, if it ever was, for your annual lecturer to apologize for including in his remarks frequent references to the arrange-ment of metal atoms in crystals and for basing his arguments that metals behave as they do upon their crystal structure. Neither will any objec-tion be raised because the large metallic crystals of which we will speak are hard to prepare and of negligible commercial interest. The particular set of physical properties we propose to discuss-ferromagnetic proper-ties-may require more justification. Very few in this audience are primarily, or even remotely, interested in the ferromagnetic behavior of the metals they handle. By no means all of you ever deal, by choice or by necessity, with metals which display any ferromagnetism at all, and even those who study or control ferrous metallurgy must usually depend upon electrical engineers for assistance in ferromagnetic applications. My excuse for talking about such an obvious specialty is, like all Gaul, divided into three parts. In the first place, the members of the com-mittee who select the annual lecturer must wish the speaker to confine himself to matters he has at least thought about before he prepares his speech. In the second place, the study of ferromagnetism in crystals has, as you will soon realize, suffered in the not-too-distant past from inade-quate metallurgy. Further progress probably depends upon proper use being made of the skill and knowledge of some members of the Institute of Metals Division who have not, before today, been asked to think about the problems presented here. Finally, there is at least a sporting chance that the ferromagnetic properties of a few metal crystals will give some insight into the more generally interesting properties which they share with nonferromagnetic metal crystals.

Jan 1, 1934

By R. Rocca, M. B. Bever

THE adiabatic elastic deformation of a body is accompanied by a change in temperature. This phenomenon is known as the thermoelastic effect. Under adiabatic conditions the temperature of a metal bar is decreased by an elastic elongation and is increased by an elastic compression. All materials which elongate on heating behave in this manner. The sign of the thermoelastic temperature change is reversed for the few materials which have a negative coefficient of thermal expansion. The following equation for the thermoelastic effect can be derived from fundamental thermody-namic theorems, as shown in the Appendix: dT8 =-a1/cs T dss [1] Cs In this equation, T is the absolute temperature, S is the entropy, a, is the coefficient of linear thermal expansion, cs&apos; is the heat capacity per unit volume at constant stress and s is the stress (positive in tension). Eq 1 can be applied to small, but finite changes in stress in the following form: ?Ts =- a1/cs T?ss [2] The sign of the temperature change AT is opposite to that of the change in stress s for materials which have a positive coefficient of thermal expansion. Eq 2 has been verified for many different materials and stresses at room temperature. No previous publication appears to have been devoted to an in- vestigation of the thermoelastic effect over a range of temperatures. Review of Literature Lord Kelvin (W. Thomson) presented a general theory of the thermoelastic effect in 1851&apos; and later applied it to a solid, subject to an arbitrary system of stresses&apos;. His analysis was based on a cycle of isothermal and constant-strain transformations and led to Eq 2 above. Even today, one of the clearest expositions of the thermoelastic effect is found in Lord Kelvin&apos;s article on elasticity in the Ninth Edition of the Encyclopedia Britannica (1878). R. ROCCA, Junior Member, and M. B. BEVER, Member AIME, are Research Assistant in Metallurgy and Associate Professor of Metallurgy, respectiuely, Massachusetts Institute of Technology, Cambridge, Mass. AIME New York Meeting, Feb. 1950. TP 2760 E. Discussion (2 copies) may be sent to Transactions AIME before APT. 1, 1950, and is scheduled for publication Nov. 1950. Manuscript received Oct. 15, 1949.

Jan 1, 1951

By E. P. Chartkoff, W. P. Sykes

In 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,&apos; including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Meas-urements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic com-pound phases upon sintering a mixture of metal powders. Materials All the specimens were prepared from the same quality of metals and by the same methods as were described in the determination of the constitutional diagrams. The metal powders as mixed and pressed were sintered or fused in a hydrogen atmosphere and subsequently treated as indicated in the titles of the figures. The formation of the iron-rich solutlon in the solid was accomplished by sintering in hydrogen for a period of 20 to 30 hr. at a temperature 25&apos; to 50&apos; C. below the melting point of the eutectic. The tungsten-rich and molybdenum-rich solid solutions of iron were prepared by adding the iron as a solution of iron ammonium oxalate to the oxide of tungsten or molybdenum, followed by a hydrogen reduction. This method results in a homogeneous alloy after sintering the pressed metal powder for 20 to 30 hr. at a temperature slightly below that of the peritectic reaction in the system involved. For X-ray examination the specimens were variously prepared, depending on the nature of the sample and what it was desired to show. For example, the iron containing tungsten or molybdenum in solid solution was cut with a file, the chips were put through bolting cloth, and this powder of filings formed the specimens for comparative study. The

Jan 1, 1930

By J. V. W. REYNDERS

NOT only is your toastmaster silver-tongued in his references &apos;to myself, but he is also quite in the habit of "saying it in silver." I have analyzed with some care his statistics of the world&apos;s silver production, which have been distributed here along with the menu, although frankly from the point of view of most of us, the distribution rather than the production of silver is of immediate concern. Unlike the performers by whom we have been entertained between courses, the rest of us on the program will have to do without costume or musical accompaniment, which as my friend Rains can testify puts an artist under severe strain. I am entitled by right of office and of precedent to receive your attention for ten minutes. The Governor, who appears on the program as a speaker; however, has asked me for five minutes of my time, and Senator Thomas has insinuated that he would appreciate one-half of the remainder, wherefore, I must ask your close attention to the very brief remarks that I am able to make under such restricted circumstances. To begin with, I want you to believe that I am approaching the task set by your toastmaster with misgivings. In looking over the Institute records relating to the Salt Lake City meeting of 1914 for some precedent as to what I ought to say, I found but one reference-and that of the following indefinite char¬acter-" and Friday night there was a hilarious banquet to 350 members and guests."

Jan 1, 1925

By E. L. BROKENSHIRE

FLUORSPAR, a little known non-metallic mineral, referred to technically as fluorite, chemically as calcium fluoride, is a compound of calcium and fluorine in the ratio of one molecule of calcium to two of fluorine. By weight it is composed of 51.3 per cent of calcium and 48.7 per cent of fluorine. Its specific gravity is 3.2. It is brittle, has a hardness of four and can be easily scratched with a knife. It weighs about 200 Ib. per cubic foot and has a melting point of 1650" F. The color of fluorspar ranges from pure white and opaque white, according to its purity, to various hues of yellow, green, pink, lavender, blue and brown, to bluish black. Although the lumps have color, when ground the fluorspar becomes pure white. The reason for this is because the mineral usually carries no fixed pigment, the color being produced by the re- fraction of light rays within the crystal structure and small quantities of organic matter which readily oxidizes. It crystallizes in the isometric system with perfect octahedral cleavages.

Jan 1, 1929

By AIME AIME

ON March 14, the University of Tulsa was accepted as a member of the North Central Association of Colleges, which ranks Tulsa among the leading universities of the country. A. G. OIiphant recently donated to the new school of petroleum engineering a splendid collection of books on geology, valued at $25,000. Waite Phillips, an oil producer and chairman of directors of The Independent Oil & Gas Co., donated $150,000 for a petroleum engineering building

Jan 1, 1929

By AIME AIME

A METALLURGICAL research building is to be erected for the Armour Research Foundation at the Illinois Institute of Technology. It will be located at the corner of Federal and 34th Sts., Chicago, and fully equipped will cost $250,000. It will provide the Middle West with the largest and most complete of facilities for the conduct of developmental and industrial research in this field. The new building will be constructed around an existing foundry and metallurgical research building which has become too small to carry on and service the many research projects contracted for by the Foundation, having to do with steel, alloys, and nonferrous metals. After two bays of the new unit have been completed, the old unit will be torn down and the new one completed.

Jan 1, 1942

By Ernest A. Hersam

IN every commercial establishment,&apos; it is customary and necessary to take inventory, periodically, and to account for profits and detect losses, to achieve productiveness and enhance efficiency. So, too, in the ordered life of every individual, there is the need of periodic introspection. The exercise of the Sabbath for rational thought, the utilization of pause, or rest, from the technique of daily occupation, orient the efforts. These are the constructive opportunities by which we grow always better than we were. Thus, also, there&apos; is need of a periodic analysis of the organizations to which we belong and toward which we con- tribute. So we find&apos; reason for the fitness of our loyalty. There seems to be no half-ground for the engineer. Whatever presumes to bear his name demands either the crushing pressure of his heel or the supporting pressure of his hand.

Jan 1, 1929

The following discussion was held on August 2.2, 1927, during the meeting of the Institute at Salt Lake City. It. IIIatch, Garfield, Utah.—The object of the meeting, I belicve, is to determine the proper chemical composition to insure long wear of a ball in a mill. This might also apply to rods. I feel that there is only one way of determining accurately the wearing qualitites of balls in mills, and that is by actually wearing out 400 or 500 tolls of different kinds of balls. Two things add to the wearing qualities of a ball: (1) the tenacity, with which the particular particles of iron or steel are cemented together; (2) the individual hardness of each partiele. My cxperience is that a ball that has a Brincll of 550 to 650 will give comparatively long life. There is considerable difference of opinion as to the best steel and iron alloys neressary to produce a satisfactory grinding ball. Some favor chrome, somr manganese and some nickel. Personally, I believe cast iron alloyed with chrome makes the best ball for small sizes; for large sizes (31/2 in. arid up) steel alloyed with mangancse is best. L. O. Howard, Pullman, Wash.—How would this method apply to hning? A. Kissock, New York, N. Y.—I do not subcrribe to that exactly. As I am connected with the Climax Molybdenum Co. you would hardly expeet me to. We have been much interested in trying to work out this grinding-ball problem and have spent a, great deal of thought and effort on it. As we are associated with the American Metal Co. and have a number of Proprrties of our own, we are in poaition to try our ideas on ourselves first. We have tried different compositions, but, have not done anything very remarkable with them yet,, except that we have been able to say that the combination of chrome and molybdenum has given the best, wearing ball. Mr. Hatch feels that iron is the best. medium for grinding, hut since toughtiess as well as hardness is a factor in wearability we feel that a well made steel is better for this purpose. Another difficulty with cast, or chilled, iron is lack of uniformity front day to day or from heat to heat, and the impossibility of protlucing balls free from blow or shrinkage holes which matcrially affect their life. If cast iron is made hard it becomes brittle and lacks strctc11 or toughness. This prevents its use in the larger sizes, aS break:lgc, is a sorious hantlic:~p to efficiency. We have trirtl hard and brittle balls and softer but very tough balls and have proved that maximum hardness, with sufficient toughuess to prevent hrcakagv, is the most important factor. in resistarnce of a steel to abrasion. It is well known that. chromium is one of the best hardening agencies for cither iron or. steel; and molybdenum is recognized as an clerment capable of introducing tonghness. In other words, the proper combination of chromium and molybdenum permits unusual hadness with still sufficient touglmess to stand up under severest impact. It is yet too early to give any actual mill results of this new Combination and though we are proving our ideas at our own properties we have to depend on others to help us make the data more general and more worth while and would like to get some testa 206

Jan 1, 1928

By Garry M. Hughes

Sherritt&apos;s new, 3000 tpd, copper- zinc Fox mine is situated 30 miles southwest of Lynn Lake. The copper-zinc orebody is part of a large body of massive and semi-massive sulfides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9s Fe) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The average sulfide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content. Surface diamond drilling indicated an orebody containing 12,269,000 tons grading 1.74% Cu and 2.35% Zn to the 2000 ft level. Underground drilling established the tonnage at 11,- 300,000 tons containing 1.96% Cu and 2.74% Zn.

Jan 4, 1972