Search Documents

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By W. C. Browning

The influence of the hydroxyl factor is more damaging to formations penetrated and causes greater consumption of drilling mud additives than previously realized. This hydroxyl effect on clays is essentially independent of the cations present in the drilling fluid and thus differs from the base exchange reactions that have preoccupied mud chemistry with sodium and calcium bentonite concepts for nearly two decades. The new organic polyelectrolyte-con-ditioned muds haw made it possible to use materials other than sodium hydroxide to maintain the alkalinity of such muds. The properties of silicates, as indicated by their dissociation characteristics and buffering action, are such that they can control he pH and alkalinity of drilling muds at the desired level and, at the same time, minimize undesirable hydroxyl effects associated with sodium hydroxide. This use of silicate compounds is different and distinct from prior applications of silicates as deflocculants or shale preservers. Laboratory and field data presented in this report show that silicate compositions can be utilized to adjust the alkalinity of drilling muds and, at the same time, minimize hydmxyl-promoted clay cleavage. INTRODUCTION Studies for improving the efficiency of rotary drilling techniques must consider the chemistry of drilling fluids and of the formations being penetrated. The chemical aspects of drilling must be studied in conjunction with and in relation to the mechanical factors if, for example, penetration rates are to be optimized. Drilling fluid technology has been largely influenced by chemical reactions of the montmorillonite (bentonite) clay minerals. Most of the literature of mud chemistry concerns the properties of bentonite. Clays of the kaolin or illite type, which are nonswelling, are not generally regarded as sources of drilling mud problems. If these nonswelling shale clays are considered, they are commonly regarded as inert solids. Particularly noteworthy is the fact that the relation of surface and colloid chemistry to massive shale bodies has received only scant attention from drilling technologists. Clay studies reported in the drilling mud literature have dealt, for the most part, with the properties of clays in a finely divided state, and often in very dilute suspensions. Yet frequently during drilling, shale problems not related to the rheology of clay suspensions develop in massive non-bentonitic shale sections of zero or near zero permeability. This paper is concerned with surface chemical reactions that can influence the behavior of these non-bentonite clay masses in such a manner as to adversely affect drilling operations. Browning and Perricone1,2 have pointed out that some of the most troublesome shales to drill, such as the Atoka, contain no montmorillonites. They also pointed out that mud problems can frequently be mitigated by reduction of clay cleavage achieved by using drilling fluids with a minimum of available hydroxyl ions. If pronounced clay cleavage occurs during drilling, the borehole may soften, increasing the possibility of sloughing. In addition, the resulting increased incorporation of high-surface-area clay solids into the mud system can reduce penetration rates and necessitate greater chemical treatment. This increase of shale, of colloidal or near-colloidal dimensions, into the drilling mud is due to clay aggregate cleavage and not to base exchange or swelling reactions, such as occur with bentonites. Searle and Grimshaw3 point out the difference between cleavage or slaking reactions of nonswelling clays (such as illite and kaolinite) and the swelling of bentonite. They further state that the speed of slaking is increased in alkaline water. Eitel1 cites Salmang and Becker, who recognized that clay surface reactions impart plasticity and workability to clay masses. Their results clearly show that all liquids which contain hydroxyl groups in their molecules favor the workability of clays. The ancient technique of aging clays in the moist condition to increase their "workability" is evidence that these clay cleavage phenomena are of considerable importance. The same hydration cleavage that occurs during the aging of nonswelling clays for ceramic use also acts to break up cuttings and soften the borehole during drilling operations. The mechanism of cleavage of the crystalline aggregates of illitic, kaolinitic and other nonswelling clays; and the chemical means of controlling this cleavage are therefore of considerable significance to the drilling mud chemistry. Inasmuch as there is little reference in the drilling mud literature to the cleavage reactions of nonswelling clays, the structure of these clays and certain properties that relate to the mechanism of clay cleavage will be reviewed briefly. STRUCTURE OF NONSWELLING CLAYS Clays such as kaolinite, illite and montmorillonite are compmed of alternate layers of (1) silicon-oxygen tetra-

Jan 1, 1965

By E. P. Pfleider, Rolland L. Blake

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the seaarch for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines' and the School of Mines at the University of Minnesota' have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs. The objective of the specific research problem" discussed in this paper was an investigation of the cutting action of the cliamonds set in a diamond drill bit, cutting action meaning the manner in which the diamonds cut or. loosen the minerals in the rocks being drilled. In the literature on cutting action such descriptive terms are used .as: grinding, wearing, cutting, breaking, shearing, scraping, melting, and chipping. These actions were seldom described or defined. Grodzinski describes the cutting action of a single diamond in the shaping of certain types of material as "breaking out chips of the material." Brittle mate-. rials break as small separate chips, and tough materials, because of heat generated, give a continuous chip. Deeby said about diamond drills: "When diamonds are forced into the formation and rotated, they either break the bond holding the rock particles together, or they cause conchoidal fracture of the rock itself. The former action occurs when drilling in sandstones, siltstones, shales, etc. and the latter action when drilling in chert, flint, or quartz." He said that diamonds cut on the "grinding principle" but he does not define or elaborate on this action. The cutting action of diamonds on glass was first investigated about 1816 by Dr. W. H. Wol-laston, an English physicist. The best glass-cutting diamonds have a natural or artificially rounded cutting edge. This edge first indents the glass and then slightly separates the particles, forming a shallow and nearly invisible fissure. Since none of the material is removed, this action is one of splitting rather than cutting. No other reports of research work on the cutting action of the diamond were found, and further work was considered justified and advisable. It is impractical, even if possible, to observe directly the cutting action of a diamond drill bit in rock; therefore it was necessary to devise an indirect method. It was believed that a study of the following three observations would lead to a better understanding of the cutting action: 1—the appearance of the minerals or rock surface in the bottom of the hole, 2—the size, shape, and other characteristics of the drill cuttings, and 3—the condition of the diamonds in the bit. The cutting action in a particular rock probably varies with bit pressure and speed. If the bit were slowly lifted off the rock, the effect of decreasing pressure might obliterate those bottom hole characteristics that are specific at the test pressure. Likewise, if the drill were stopped with the bit still in contact with the bottom of the hole, then decreasing speed effects would tend to obliterate the characteristics at the set test conditions. Therefore, in order to preserve those cutting effects impressed on the rock at test conditions, it seemed necessary to lift the bit off the bottom of the hole almost instantaneously once drilling conditions, i.e., revolutions per minute, pressure, and water flow became constant. In addition to observing the cuttings, the bit, and the bottom of hole, it seemed desirable to collect some quantitative data for purposes of correlation with the observations and for a record of bit performance. Consequently such data as revolutions per minute, force applied, and rate of advance of the bit were recorded. Six rock types, listed in Table I, were chosen for the tests. It was felt that these rocks had most of the variable characteristics of texture, bonding, and mineral hardness met in the common rocks generally being drilled. The sandstone was so poorly cemented as to be friable, even though most of the cement was silica. The limestone, though well cemented, was quite porous. Originally it was planned to conduct the tesk work with a full-scale drill unit, using EX bits, 7/8-in. core, 11/4-in. OD. The drill worked well, but was too cumbersome for rapid, accurate drilling of many short holes (1 ½-in.) in varied rock types. A new

Jan 1, 1954

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall's work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann's approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen's approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

By AIME AIME

EARLE EDWARD SCHUMACHER, the new Chairman of the Institute of Metal, Division. is well known to the metallurgical profession. His election a, Chairman is the culmination of fifteen years' service to the Institute, beginning in 1930 when he was elected Member. Since that time he has served as member of the I.M.D. Data Sheet Committee. 1935-40; Papers and Publication Committee. 1936; Executive Committee. 1937-1910: Papers and Programs Committee, 1937-1938. (Vice-Chairman, 1939-40, Chairman. 1941-12): Annual Award Committee. 194142. (Vice-Chairman, 19431: Vice-Chairman, LM.D., 1943-44; Chairman Publication Committee, 1943-44; member Powder Metallurgy Committee), 1944. Pew other men have contributed so Much time anti effort in so many way- to the interests of the metals branch o4 the A.I.M.E.

Jan 1, 1945

By George S. Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro- posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By AIME AIME

BEFORE proceeding with the papers scheduled for the ore and foundry session*, the teller's report on the election of officers for the ensuing year was presented, a; follows: Chairman. G.C. F. MacKenzie; vice-chairmen, C.S. Robinson, J. T. MacKenzzie, C. E. Meissner; executive committee, A. L. Field, R. F. Harrington, E. F. Kenney lit. Waterhouse announced that the fall meeting will be devoted to alloy steel. This meeting will be held in Chicago the week of Sept. 22 in connection with the National Metal Congress. He also announced that oxygen in steel will be the central idea of the meeting which will be held in New York next February. The first paper, entitled "Sintering Limonitic Iron Ore at Ironton, Minn.," was presented by Perry G. Harrison (T. P. 284), the author. Sintering was first un¬dertaken in 1024 to treat Cuyuna range iron and manganiferous ores low in silica and high in moisture and containing objectionable qualities of fine... A Dwight-Lloyd machine was first installed. This machine was replaced by a larger one having a width of 72 in. The power cost was decreased from about $11.22 per ton of sinter on a 42-in. machine to about X0.14 for the 72-in. machine. The tons of sinter per man-shift was increased from 11.86 to 16.77. Improvements embodied in the larger plant reduced the cost of sintering to $0.41. The analyses of iron ore and manganiferous ore and the sinter produced from these materials was used to show the increase in value at the mine resulting from sintering. Crude iron ore actually unsalable was increased in value f.o.b. mine from a theoretical figure

Jan 1, 1930

By H. M. Chance

The recent discoveries of important new gold-districts in limestone, granite, sandstone and porphyry have awakened the more intelligent class of prospectors to a realization of the fact that ally rock may be gold-bearing; that from the appearance of a rock it is impossible to judge whether it carries gold or not; and that gold-ores may occur in any geological formation. As a rule, the professional prospector limits his search to ores and conditions with which he is more or less familiar, and to formations which he regards as favorable to the occurrence of such ores. Hence it often happens that while the very thing he is searching for is in plain sight, he fails to recognize it, and some other individual, possibly less intelligent but more lucky, stumbles blindly upon it. Beginning with the discovery of the California placers by the finding of gold in the tail-race of Sutter's saw-mill—a tale so often told that nearly all have read it in some form—and following the discovery of district after district down to the present time, one is forcibly impressed by the fact that many of the important districts have been discovered by accident; that many such discoveries have been made by unskilled or inexperienced prospectors, and some by persons having no knowledge whatever of prospecting. Thus, the recent Klondike discoveries are said to have been made by a poor salmon-fisherman, who, with his Indian wife, was hunting, not for gold, but for good fishing-grounds; the Comstock lode is said to have been accidentally discovered, and the Ragged Top district in the Black Hills and the Pearce mine in Arizona* are recent notable instances of the same kind.

Jan 1, 1900

By N. J. Grant, A. W. Mullendore, Y. Ishida

Creep tests were performed at 500°F on polished specimens of A1-3 pct Cu at stresses of 2000, 4000, and 6000 psi. The effects of the size and distnbution of the second phase were studied in connection with the mechanisms of deformation, especially grain boundary sliding. Although the amount of grain boundary sliding varied considerably for the different heat treatments, yestriction of grain boundary sliding is not due primarily to precipitate on the grain boundary. NUMEROUS prior investigations of grain boundary sliding, notably those of McLean, 1 Rachinger, 2 Rhines, Bond, and Kissel, 3 and Brunner and Grant,4 have established the importance of this phenomenon in the deformation of pure aluminum and its solid-solution alloys at elevated temperatures. An extension of this kind of study to the case of a simple two-phase structure is an important step towards understanding the deformation behavior of more complex alloys. A two-phase A1-3 pct Cu alloy was selected for this study. The creep behavior of alloys in this system has been studied by Sully and Hardy,5 by Underwood, Marsh, and Manning,' and by Pelloux, Chaudhuri, and Grant.7 In these studies, the prior heat treatments were such that some precipitation took place during the tests in most cases. Pelloux, Chaudhuri, and Grant7 studied the creep of A1-2 and 3 pct Cu alloys in the overaged condition. Their results indicated that the structure most effective in promoting high-temperature strength consisted of a fine, closely spaced grain precipitate and large, widely spaced particles on the grain boundary. The present work consists of quantitative meas- urements of grain boundary sliding during creep of an A1-3 pct CU alloy with four different precipitate distributions. The aims were to quantitatively define the role of the second phase on grain boundary sliding, and to obtain information regarding the mechanism of grain boundary sliding. MATERIALS AND PROCEDURE A high-purity A1-3 pct Cu alloy, kindly supplied by Alcoa, was used in this investigation. The composition of the alloy in weight percent was as shown in Table I. This composition is such that A12Cu exists as a second phase at temperatures below 850°F. A homogeneous grain size of 0.6 to 0.8 mm was obtained by annealing the machined test bars for 5 min at 1000°F, furnace cooling to 930°F, and homogenizing for 5 hr. Following the recrystalli-zation and homogenizing anneal, four different heat treatments shown in Fig. 1 were utilized. The F7 and F5 treatments utilize a furnace cool to the aging temperature while Q7 and Q5 have a water quench from the homogenization temperature before aging. Figs. 2 to 5, and Table 11, show the size and shape of precipitate dispersions obtained with the above heat treatments. The heat treatments produce variations in the dispersion both in the grains and along the grain boundaries. Precipitate particles along the grain boundaries are rounded and large (about 1.5 p diameter) in the F5 and F7 structures (Figs. 3 and 5). The grain boundary precipitate was somewhat smaller (0.9 p diameter) in the Q7 structure and no grain boundary precipitate was detected in the Q5 structure using light microscopy. The pre-

Jan 1, 1964

By D. L. Albright, R. W. Kraft

Solidification experiments were conducted with the objective of testing the theory of eutectic colony formation. Appropriate control of variables in tests on a series of high-purity aluminum-copper specimens of eutectic composition resulted in the observation of three types of eutectic microstructures, these being a unique structure consisting of lamellae essentially parallel to one another, a banded structure, and the colony structure. Lamellar faults, which are morphologically similar in many respects to edge dislocation models in crystals, produced a complex substructure in these specimens. SOLUTE rejection at the advancing solid-liquid interface of a unidirectionally solidified single-phase metal can cause the liquid immediately in front of the interface to become constitutionally super-cooled below the equilibrium liquidus temperature. Constitutional super-cooling occurs if the solidification rate, R, is too rapid, or if the thermal gradient in the liquid at the interface, G, is too low. 1 This constitutionally supercooled layer in turn stabilizes a cellular rather than a planar interface.&apos; A similar cellular interface has been observed when lamellar and other types of eutectics were unidirectionally solidified, and it has been shown that the cellular interface led to the formation of eutectic colonies.&apos; The lamellar structure is fan-shaped at the edges of colonies (which correspond to valleys or grooves in the cellular interface) because the lamellae grow normal to the local interface. One of the possible mechanisms which might cause the formation of the cellular interface, in the case of solidifying eutectic alloys, is constitutional supercooling of the liquid with respect to a third component rejected by both phases of the eutectic.3,4 On the basis of the analogy between the solidification of single-phase metals and binary eutectics, a eutectic alloy should solidify with a planar interface if the ratio of G/R is sufficiently high to compensate for any impurity which might be present and causing constitutional supercooling. The fan-like microstruc-ture of eutectic colonies should not occur under these conditions and the lamellae should be parallel to one another and to the solidification direction for extended distances. The experiments conducted in this investigation were designed to test these ideas. Following a resume of the experimental procedure, the various microstructures observed during the study are described, and their relationship to the growth conditions which produced them is discussed. EXPERIMENTAL PROCEDURE The eutectic between an aluminum solid solution and 0 phase (approximate composition CuA12) was chosen for this work for the following reasons: it was known that a lamellar structure forms, the eutectic temperature is low enough to facilitate experimental work, and the components can be procured commercially in a very pure form. High-purity copper (est. 99.999 pct Cu, obtained from National Research Corp.) and spectrographic aluminum rods, having impurities other than copper estimated to be Zn-15 ppm, Mg-10 ppm, Fe-3 ppm, Na-2 ppm, Cd-1 ppm, and Mn < 1 ppm, were melted in a stabilized zirconia crucible in a vacuum induction furnace at a pressure of 10 pof Hg. The melt was superheated to about 1000°C to assure mixing, cooled to 780°C and cast into an investment mold which yielded sixteen cylindrical specimen blanks 1/2 in. in diam and 5 1/2 in. long. The casting was allowed to solidify under vacuum. This master heat had an analysis of 32.6 wt pct Cu and 67.4 wt pct A1 by difference. The cylindrical specimen blanks were remelted and solidified unidirectionally in an apparatus illustrated schematically in Fig. 1. An RF induction coil heated

Jan 1, 1962

By L. E. Mannion

Sodium carbonate or soda ash is one of the two principal alkalis of commerce, the other being sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines or solid salts were the source of impure soda for glass manufacture. In early modern times until the 19th century, soda ash, as well as potash, was recovered mainly by leaching the ashes of plants. In Europe, during the 18th century, a brown lye for laundering was produced by pouring hot water over burned seaweed. One of the better grades of this kind of material was a product from Spain termed "barilla," which analyzed 24 to 30% Na2CO3 (Hou, 1942). The birth of the modern chemical industry may be said to start with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. Although invented in France in 1691, England made the most extensive use of it. In 1863 Ernst Solvay devised the ammonia-soda or Solvay process, and by 1874 the first of many Solvay plants was built. These were to supplant the LeBlanc method and dominate soda-ash production until the present time. Although of lesser importance, natural sodium carbonate deposits continued to support operations in various parts of the world. Shortages during World War II stimulated production of "natural" soda ash, particularly at Searles Lake, Calif., and at Lake Magadi, Kenya. Within the last ten years in the United States, a notable surge in production has occurred based on the vast trona deposits in Wyoming. Table 1 lists some principal producers of natural soda ash and the character of the source deposits. Uses and Specifications Sodium carbonate (Na2CO3) is a white, crystalline hygroscopic powder, an aqueous solution of which is strongly alkaline. Most commercial soda ash is a product that must meet high standards of purity and uniformity. Two forms are commonly sold: a fine, powdery material called light ash, and a more coarsely crystalline dense ash; these weigh 32 to 39 and 60 to 66 lb per cu ft, respectively. Dense ash may be produced by adding a little calcium chloride to the sodium carbonate solution to control crystal size and prevent agglomeration. Specifications and typical analyses of light and dense ash in the United States are shown in [Table 2]. Sizing generally achieves about 75% of light ash and 90% of dense ash between +30 and -100 U.S. screen mesh. World use of sodium carbonate now exceeds 24 million tpy, of which the United States produces more than 7 million tons. The market for soda ash is dominated by the glass industry, which uses almost half the supply. Inorganic chemicals, including phosphates and silicates, consume about 30%. Other principal uses include the manufacture of soaps and detergents, petroleum, caustic soda, organic chemicals, and paper; and nonferrous and ferrous metallurgy. [Fig. 1] shows the percent consumption by use of soda ash in Europe, Japan, and the United States. The price of soda ash in the United States remained relatively stable during the 1960s at about $33 per ton; in 1972 it reached $35 per ton. The price in 1975 was $42 per ton. Geology Mineralogy [Table 3] is a list of the more common sodium carbonate-bearing minerals. Anhydrous sodium carbonate is almost never found in nature; only natron, thermonatrite, and trona have been used directly as sources of sodium carbonate. At Searles Lake, burkeite and hanksite are important in the reconstitution of

Jan 1, 1975

By L. B. Gittinger

Sulfur is a nonmetallic element widely distributed in nature. It constitutes 0.06% of the earth&apos;s crust but only a very small portion occurs in sufficiently concentrated amounts to justify mining. Sulfur occurs in practically all animal and plant life. It constitutes approximately 0.09% of the elements in the oceans; it has been found in meteorites. Sulfur was known and used by man before recorded history. The American Chemical Society approved spelling for the element is sulfur. The English spelling sulphur is used commercially in the United States. In ancient times, sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Sulfur is found naturally in the elemental form in subsurface deposits associated with gypsum and anhydrite in salt domes and sedimentary formations in evaporite basins and in solfatara-type deposits associated with volcanoes and mineral springs. Sulfur occurs also in molecular combination in ferrous sulfides (pyrites and pyrrhotite) and nonferrous sulfides (copper, lead, zinc, and nickel), and in mineral sulfates (gypsum and anhydrite); as hydrogen sulfide contaminant in natural gas; as organic compounds in crude oil and tar sands; and as pyrite and organic compounds in coal and oil shales. Sulfur resources are abundant and exist throughout the world but the extent to which they can be classified as reserves is greatly circumscribed by prevailing prices and technology. Estimates of world sulfur reserves are compiled by the U.S. Bureau of Mines. A compilation of reserves by area and source of sulfur published in 1970 and presented here as [Table 1] totaled 2.47 billion tons (Lewis, 1970). The effect of the decline in prices which has occurred since the earlier estimate is dramatically illustrated by the 1972 estimate of the U.S. Dept. of the Interior which shows world sulfur reserves of only 1.2 billion tons (Anon., 1972d). Sulfur is produced commercially from one or more sources in nearly 70 countries of the world. World production of sulfur in all forms totaled 41.6 million tons in 1971. (Sulfur statistics given in this chapter are long tons.) Native deposits, sulfides and oil and gas contributed, respectively, 31, 41, and 25% of world production (Table 2). Of the sulfur produced from native deposits, salt domes accounted for 54% and evaporite basin deposits, 44%. Volcanic deposits are of little significance except for local consumption. The past two decades have seen important shifts in the world&apos;s sulfur sources. In 1950, native deposits and sulfides each supplied about one-half of the world&apos;s production. During the 1950s, sulfur recovered from oil and natural gas grew rapidly, representing about 10% of the total by 1960. Since then, the petroleum industry has continued to increase its relative importance as a source of sulfur, representing more than 30% at 1972 year-end. Sulfur is generally classified as elemental or nonelemental for statistical purposes. Elemental sulfur is sulfur produced in the pure, uncombined form. It includes production from native deposits, as well as that recovered in the elemental form from oil and natural gas or other sulfur-bearing materials. When produced from other than native deposits, it is generally referred to as recovered elemental sulfur. Nonelemental sulfur is that which is utilized commercially in molecular combination with other elements, such as sulfides or sulfates. Elemental sulfur is being produced from salt dome deposits in the Gulf Coast region of the United States and the Isthmus of Tehuantepec in Mexico, and from evaporite basin deposits in west Texas, Poland, Sicily,

Jan 1, 1975

By J. L. Thompson

There are two basic forms of the LPG-slug process: the gas driven and the water driven. The pressure required for miscibility between gas and LPG prohibits the use of the gas-driven LPG process in shallow reservoirs. The water-driven LPG slug process normally exhibits good sweep efficiency. However, displacement of the LPG by water is poor. An improvement in this process appears possible by injecting a slug of carbon dioxide between the LPG slug and the water drive. Laboratory experiments were conducted in homogeneous linear systems to determine the effect of pressure on the various displacement zones. In the carbon dioxide-LPG displacement zone, the effect of pressure on the displacement efficiency is negligible above the miscibility pressure. However, the displacement efficiency decreases linearly with decreasing pressure below the miscibility pressure. With water displacing carbon dioxide, it was found that the recovery of carbon dioxide after water breakthrough can be predicted from its solubility in water. A displacement test was conducted with LPG and carbon dioxide slugs large enough to avoid interference between the oil-LPG, LPG - carbon dioxide and carbon dioxide - water displacement zones. Under these conditions, essentially complete oil and LPG recovery was obtained. However, a substantial amount of carbon dioxide was left in the core at water breakthrough. INTRODUCTION It has been shown in homogeneous linear systems that essentially complete oil recovery can be obtained by displacement with a miscible fluid such as LPG. Economic considerations dictate that the valuable LPG also be recovered. Methods proposed for recovering the LPG include (1) displacement with natural gas at a pressure high enough to make the two fluids miscible1 (the disadvantage of this method is that the required pressure of about 1,500 psi is too high for shallow reservoirs) and (2) displacement of the LPG with water2 (principal disadvantage is that a large amount of LPG remains in the formation because of poor displacement efficiency). This paper treats an improvement in the water-driven LPG slug process3,4 where carbon dioxide is injected between the LPG and water. Carbon dioxide is completely or at least partially miscible with propane and soluble in water; thus, displacement efficiency is improved at both ends of the carbon dioxide slug. To minimize effects of other variables, all experiments were conducted in linear core systems. GENERAL PROCESS DESCRIPTION The displacements of propane by carbon dioxide and carbon dioxide by water are considered separately, assuming enough of each is injected to prevent mutual interference. Displacement descriptions are confined only to the part of the pore volume containing mobile fluids unless otherwise specified. The schematic representation is given in Fig. 1. Starting at the producing well, a zone containing only oil is followed by a zone containing a single-phase mixture of propane and oil. The concentration of propane increases in the direction of the injection well and ultimately grades to pure propane. Then follows a zone containing a mixture of propane and carbon dioxide in continuously varying proportions until 100 percent carbon dioxide is reached. In this zone, the concentration of carbon dioxide in the immobile water phase also varies from zero to full saturation. Whether the displacement of propane by carbon dioxide is of complete or partial miscibility depends on pressure and temperature (Fig. 2). If the horizontal line representing the prevailing pressure intercepts the boundary curves of the phase envelopes for the prevailing temperature (i.e., if the pressure is lower than the critical

By John P. Huger

me phase diagram for the system Ag-Si has been established by thermal analysis. The diagram is a simple eutectic type with a eutectic at 3.0 pct Si and 840°C. From the liquidus curve and with the aid of regular solution theory, the thermodynamic properties of the liquid Ag-Si system at 1420 °C have been determined. Silicon exhibits positive deviations from Raoultain behavior at all compositions, while silver exhibits both positive and negative deviations. MEASUREMENTS of silicon activities in liquid iron alloys by means of distribution studies between the immiscible liquids silver and iron have been reported by Chipman, Fulton, Gokcen, and caskey.&apos; The applicability of this technique is dependent, however, on the accuracy of the silicon activity values in the Ag-Si alloys, particularly in the dilute silicon region. Darken and Gurry2 have shown that log ?si/(1-xSi)2 is approximately linear with composition, but uncertainty exists in the extrapolation to dilute solutions. Their calculations are based on the old Ag-Si phase diagram of Arrivaut3 and any variation in the position of the liquidus curves will strongly influence the extrapolation. The purpose of this study is to redetermine the Ag-Si phase diagram and calculate the associated thermodynamic properties. EXPERIMENTAL The Ag-Si phase diagram was determined by thermal analysis of liquid alloys. The alloys were contained in a 35 mm alumina crucible under a protective stream of purified argon. The crucible was placed inside a 64 mm alumina tube fitted with a gas-tight, water-cooled, copper head. The tube and assembly were heated in a manually controlled globar furnace. The temperature was measured with a Pt, Pt + 10 pct Rh thermocouple in a high-temperature porcelain protection tube. The thermocouple calibration4 was checked against the melting point of pure silver at the start and during the course of the experiments, and against both gold and silver at the completion of the experiments. The alloys were prepared from granular silver analyzing 99.95 pct Ag and powdered silicon analyzing 99.88 pct Si and 0.026 pct Fe. Approximately 150 g of alloy were used for each run. The composition of the alloy was determined by withdrawing samples of the liquid alloy with a vycor tube-aspirator bulb device. Analysis of solidified samples agreed, for alloys containing less than 23 pct Si, within ±0.3 pct Si of the calculated composition. Duplicate samples showed a variance within 50.05 pct Si of the mean analysis. The alloy was heated to 100&apos; to 20pC above the estimated liquidus temperature and then the furnace was adjusted to give an average cooling rate of 2" to 7°C per min. A cooling curve was obtained by taking potentiometer readings at 15-sec intervals. Several analyses were made by recording the thermocouple output on a high-speed, Stip-chart recorder, with the exception of run NO. 11, a minimum of two thermal analyses were made for each alloy and the cooling curves then obtained duplicated the liquidus and eutectic temperatures to about 1°C. RESULTS The results of the thermal analysis are given in Table 1, and are represented as the Ag-Si phase dlagram, Fig. 1. The eutectic composition was found

Jan 1, 1963

By H. S. Wang, Y. P. Gupta

Diffusion of zinc and germanium in liquid silver is measured in the temperature range 975" to 1400°C by use of the capillary-reservoir technique. The ex-perinzental results are discussed in terms of the fluctuation and the "hole" theories of liquid diffusion, assunzing the solute as a point charge equal to the difference in the valences of the solute and solvent atoms. The additional coulombic interaction term due to the excess solute charge is evaluated in terms of the Thomas-Fenni approximation. The theoretical and experimental results agree with both the fluctuation and "hole" theories of liquid diffusion. No perceptible effect on solute diffusion in liquid silver of the size difference between the solute and solvent atoms/ions is apparent. DIFFUSION in liquid silver of electropositive solutes indium, tin, antimony, and homovalent gold has been previously reported by Leak and Swalin1 and Gupta,&apos; respectively. These solutes have nearly the same atomic size but differ principally from one another in excess valence (+2, +3, +4, respectively). The observed differences in the temperature dependence and the rate of solute diffusion were explained in terms of an added coulombic interaction between the solute and the solvent atoms. In the case of diffusion of gold in liquid silver, the data were found to be consistent with an effective valence for gold of -0.85, as proposed by Le Claire.3 Recently, Wang and Gupta4 have reported a study of diffusion of ruthenium, iron, and cobalt in liquid silver. The results of diffusion of these solutes and their temperature dependence were found consistent with the hole theories and the fluctuation theories of liquid diffusion, if ruthenium, iron, and cobalt were diffusing in liquid silver with relative valences -2, -1.3, and -0.5, respectively, instead of -3, -3, and -2 as suggested by the relative position of these elements in the Periodic Table of Elements. Furthermore, the predicted valences for these solutes were observed to be consistent with the sparsely available information on the magnetic properties of some of the dilute alloys of copper and silver with these solutes. In theoretical calculations of solute diffusivity, the solute was assumed as a point excess charge equal to the difference in the valences of the solute and solvent atoms. Both the assumption of a point excess solute charge and the use of the Thomas-Fermi approximation to calculate the potential of a solute charge are less precise for the case of electronegative solutes. Therefore, it was not possible to infer from the data on ruthenium, iron, and cobalt an effect, if any, on solute diffusion of the relative differences in either the Period or the size of the solute and solvent atoms or the solute atoms themselves. A study of the diffusion of Period 4 elements, specifically zinc and germanium was, therefore, undertaken since zinc and germanium, respectively, have relative valences of +1 and +3 in liquid silver and the data obtained on diffusion of these solutes could be compared with the available data on diffusion of Period 5 electropositive solutes, indium, tin, and antimony in liquid silver. From such a comparison, it was hoped to learn something about the effect, if any, of the ion size or the structure of the ion core on impurity diffusion in liquid silver. EXPERIMENT The diffusion of tracer zinc and germanium in liquid silver was studied by the capillary reservoir technique, modified adequately for use at high temperatures. In principle, capillaries containing liquid silver

Jan 1, 1970

By Philip R. Strand

Vermiculite is the name used for those micaceous minerals with a ferromagnesian aluminum silicate composition and the unique property of exfoliating to a low density material when heated. Commercially, the exfoliated products are also called vermiculite, or more exactly, expanded vermiculite. In its exfoliated state, vermiculite serves many markets, chief among them construction, agriculture, horticulture, and general industry. Composition and Properties Vermiculite, in a natural state, has the characteristic mica habit, splits readily into thin laminae, flexible but inelastic. In a mineralogical sense, vermiculite is a hydrated silicate with no exact chemical composition. The structural formula for a macroscopic, trioctahedral vermiculite may be written: [ ] The structure of vermiculite is basically that of a talc, and it could be regarded as a trioctahedral member of the smectite group. Macroscopically, vermiculite displays the prominent monoclinic crystal faces that are commonly marked by lines at 60° and 120°. Hardness varies from 1.5 to 2.8 or more; specific gravities are between 2.1 and 2.8; color is amber, bronze, brown, dark green, or black. When heated quickly to an elevated tempera¬ture, vermiculite expands by exfoliating at right angles to the cleavage, into wormlike pieces (the name vermiculite is derived from the Latin `vermiculare,&apos; to breed worms). This characteristic of expansion, the basis for commercial use of the mineral, is the result of the mechanical separation of the layers by the rapid conversion of contained water to steam. The increase in bulk volume of commercial grades is 8 to 12 times, but individual flakes may expand as much as 30 times. All expansion occurs at right angles to the basal cleavage. Vermiculite may also be expanded by a number of chemical processes such as soaking in hydrogen peroxide, weak acids, and other electrolytes. There is a color change during expansion that is dependent upon the composition of the vermiculite and furnace atmospheres. Heating in an oxidizing atmosphere produces dull gray colors. The iron is generally not oxidized during chemical expansion. The exfoliation of the vermiculite crystal results in large pores being formed between groups of platelets. Thus exfoliation can make available a large increase in void volume without significantly changing the surface area of the platelets. This characteristic is important in the chemical carrier applications of vermiculite. Although there has been much research on the chemical and structural composition of vermiculite, an exact formula and composition cannot be described. This is to be expected since vermiculite derives from a number of different mineral sources. As has been proposed, vermiculite is not a single mineral species, but families of related minerals. Additionally, commercial interest in the end product has resulted in the name vermiculite being applied to the very voluminous, bloated products from calcination of baueritized (bleached) phlogopite. This has also resulted in many names for the specific vermiculite found in a particular deposit. All of this difficulty arises from the nature of its crystal chemistry. Consequently, vermiculite is now thought of as several related variable mineral series rather than a group of related species. The vermiculites have a common silica tetrahedral sheet structure with separating ions. It is now generally agreed that vermiculites must also be regarded as true clay minerals. The properties of the mineral, such as cation exchange capacity, organic complexing ability, and vari-

Jan 1, 1975

By Charles W. Chesterman

Perlite is a glassy volcanic rock which will, upon rapid controlled heating, expand or "pop" into a frothy material of low bulk density, valued as a lightweight aggregate. The term perlite also is applied to the expanded product. The chemical composition of perlite ranges from that of rhyolite to that of andesite; the water content ranges from 2 to 5%. Most perlite is pale gray, but some is black, brown, or even green. Inclusions in perlite are common and include phenocrysts of quartz, feldspar, biotite, and hornblende, and miscellaneous rock fragments. Occurrences of perlite are restricted to areas of Tertiary and Quaternary volcanic rocks. Perlite occurs as flows associated with thick accumulations of pyroclastic debris and other flow rocks, as dikes, sills, domes, and as selvages of intrusive bodies of volcanic rock. Individual flows of perlite range in thickness from a few feet to as much as 100 ft and commonly cover several square miles. Dikes and sills of perlite generally are small, but domes generally are substantial in size and may be as much as several miles in diameter. Most perlite deposits are large enough and topographically situated so as to lend themselves to low-cost open pit mining methods. Conventional equipment is employed in the mining of perlite. Although milling procedures may appear to be simple, care is exercised in order to produce a carefully sized product and to minimize the production of excessive quantities of fine materials, which have limited use and are considered as waste. Perlite is processed, or "popped," in one of two basic types of furnaces: horizontal rotary or vertical stationary. Both types of furnaces include product collection and dust control systems. Many commercial deposits of perlite are known to occur throughout the world, and although no exact estimate of reserves is available, there appears to be an adequate supply to meet current and future worldwide requirements. End Uses The uses of expanded perlite are many and varied and are based primarily upon its physical and chemical properties. Because of its (1) low bulk density, which generally ranges between 2 and 20 lb per cu ft; (2) low thermal conductivity "K" factor (Btu per hr per sq ft per OF per in, of thickness), which ranges between 0.267 for loosely packed perlite (bulk density of 4.48 lb per cu ft) to 1.25 for perlite gypsum plaster; (3) high resistance to fire; and (4) low sound transmission, expanded perlite is used to a great advantage as aggregate and insulating material in the construction industry. Early uses of perlite were related exclusively to the construction industry, which now consumes about 60% of the domestic production. The primary use of perlite now is as aggregate in insulation boards. Other uses of perlite in 1971 were as aggregate for plaster, horticultural aggregate, low-temperature insulation (cryogenics), and concrete. Because of its low thermal conductivity ("K" factor), high adsorption of sound, low bulk density, and fire resistance, perlite aggregate plasters hold many advantages over conventional plaster. Perlite aggregate plaster lends itself to machine applications, dries quickly, and has relatively high elasticity which reduces cracking after drying. These same features make perlite useful as aggregate in portland cement concrete and asphalt concrete for construction wherever weight reduction, insulation, and acoustics are of prime importance. Perlite-portland cement concrete offers up to 20 times more thermal insulation than conventional concrete, and because of this it finds wide application in roof decks and floor fill in multistory buildings, in

Jan 1, 1975

By J. Skrove, C. R. Boardman

In situ permeability of the rock outside the Hardhat chimney was determined by pressurization of long holes with air. Experimental data indicated a remarkable difference between fracture permeability of the rock near the chimney and that at a considerable distance. Although permeable fault zones were known to exist in the granite stock, the measurements of background permeability were quite low, on the order of tenths to several millidarcies. The observed difference is about two or three orders of magnitude above this background in the region 125 to 215 ft radially from the shot point, or 80 to 165 ft radially from the vertical axis of the chimney. The presence of a collapsed drift immediately beyond this region precluded measurements which could have defined the maximum extent of the zone of high permeabilily. INTRODUCTION Previous exploration has revealed that contained nu-clear explosions create cavities which generally collapse, resulting in rubble-filled chimneys and annular fractured zones. These geometries have been shown to result in complex flow regimes which should increase the production rate from hydrocarbon reservoirs.&apos; Empirical scaling equations have been developed for estimatina chimney radii and heights for a variet; of rock media.&apos; The exten; of the annular fractured zone has been documented and associated permeability changes have been observed qualitatively for several explosions. This study was begun to establish the nature and magnitude of the permeability of the latter region. It is anticipated that results will be useful in estimating permeability changes and consequent production stimulation which might ensue from a contained explosion in a hydrocarbon reservoir. The post-shot environment of the Hardhat event (a 5-kt contained nuclear explosion in granitic rock) was c&apos;hosen for the experimental measurements. The Hardhat device was detonated at a depth of 939 ft, and subsequent exploration revealed a chimney of broken rock with a radius of 65 to 70 ft and a height above shot point of 281 ft.&apos; BeFore the explosion, the Hardhat medium was highly jointed and fractured (Fig. I). Jt was expected that differential rock motion along these and other weaknesses induced during cavity growth and collapse would significantly alter the permeability of the rock mass. EXPERIMENTAL METHOD Initially, three 2-in. diameter holes (Nos. 10, 12 and 19) were drilled about 25 ft outward through the walls of the 500-ft level drift (elevation 4,253 ft, Fig. 2). One was drilled near the chimney and two holes, one vertical and the other horizontal, were drilled near the shaft. Order-of-magnitude differences in permeability obtained by pressurization measurements indicated further: investigation was warranted. A series of 3-in. diameter holes was then drilled with water as a coolant into the walls and roof of the drift (Fig. 2). An 11-in. long packer was set from 1 to 8 Et inside each hole and air was injected at measured Row rates. Hole pressures were monitored at the collar. Permeability was low enough in the holes near the access shaft that pressure could be maintained long enough to obtain good pressure decay rates. In the vicinity of the chimney, however, permeability was so high that this was not possible and air was injected under steady-state conditions. About one year later, these same holes were retested to

Jan 1, 1967

GENERAL GEOLOGIC DESCRIPTION The mineral deposit of this case study can be described as a "typical" porphyry copper deposit of the southwestern USA and northern Mexico mineral province. The copper mineralization is related to Laramide age intrusives of intermediate composition which have been intruded into older, mostly crystalline, host rocks. Post Laramide deformation and faulting have subjected the deposit to erosion, leaching, and enrichment processes, which have created a secondarily enriched chalcocite zone. Later basin and range faulting down dropped the ore zone, resulting in deep burial beneath late Tertiary conglomerates and gravels, thus preserving the deposit from further erosion and oxidation. Lower grade chalcopyrite mineralization constitutes the primary zone underlying the enriched blanket. MANAGEMENT OF SAMPLE DATA Sample data were obtained from exploration diamond drill holes that were collared vertically and drilled with surface rigs. Most of the holes were surveyed downhole and found to deviate significantly from the vertical. The data were keypunched from original drill hole logs to formats as described in Chapter 6. Three types of cards were prepared: 1) A heading card containing the following information: [Project Name Coordi-in_ Hole Collarnates Bear-clina-Total ID Northing Easting Elevinglion Depth] 2) Individual record cards following each heading card with the following information: [SampleMin. Zone interval Assay Fields Leached (enriched ID From-ToTotal Cu Oxide Cu primary)] 3) Where downhole survey data were available, a card was punched for each downhole survey point. The card image looked very much like the heading card, followed immediately after the heading card, and contained the following information: [Hole Sur Point Sur Point Sur Point ID Bearing Inclination Depth] The keypunched data were then processed by the drill hole survey program producing a record file which contained information as follows: [Line 1. Project Name Date Assay Field Identifiers Line 2. Hole ID Northing Easting Elevation Bearing Inclination Number of Samples Line 3 through N+ 2 (where N equals the number of samples in the hole) Top Min. of Min. Zone Zone Sample Sample Coordinates Sample Assays Leach InterLength Northing Fasting Elev Total Cu Oxide Cu (etc) face] MINERAL BOUNDARY PROBLEM AND TREATMENT According to the geologic description, at least three mineral zones are present within the ore limits, as well as fault boundaries and a buried topographic surface, each of which have to be considered. The interfaces of the various mineralogical and geological boundaries were identified as accurately as possible in each drill hole by the project geologist, the location of the interface was surveyed in the computer program in association with the nearest sample intercept to the interface (note last field of line 3). Thus, the boundary is represented as a point in 3D space at each intersecting drill hole. The linear interpolation (LINTERP) program then searched the last field of the surveyed record to find the top of each mineral zone, or geologic boundary, and read the coordinates associated with that sample point. The program then used the coordinates to compute an interpolated surface between all existing data points as described in Chapter 11. A contour map was plotted for each of the computed surfaces and reviewed by the project geologist. Where the surfaces were poorly defined due to lack of real drill hole information, the geologist, at times, inserted a "pseudo" drill hole intercept according to his best judgment and feeling for the configuration of the surface, and such points were entered into the data stream for LINTERP. When the project geologists were satisfied that they had obtained

Jan 1, 1980

By R. C. Amero

FULLERS earth is a general name applied to claylike minerals that have high natural ad-sorptive powers. They are usually distinguished from ordinary clays by a higher content of combined moisture and a lower apparent density. The definition is based on the ancient use of the material for fulling, or cleansing woolen cloth of oil and grease; a more modern definition should mention the ability to decolorize oil and should differentiate between fullers earth, which is naturally active, and certain bentonites which only develop decolorizing power after being leached with strong mineral acids. The distinction between fullers earth and activable bentonite is not a sharp one, since all types of intermediate clays can be found that are more or less naturally active, yet more or less responsive to acid treatment. The differences seem to depend somewhat on the amount of leaching that has been effected by natural ground waters. Physical Properties The principal mineral constituent of activable bentonite is montmorillonite, a hydrous aluminum silicate to which the following formula is generally assigned: Al,Si,O,, (OH), • 12H,O Fullers earth, as well as bentonite, is usually composed of some variety of montmorillonite, but in the United States the largest tonnage of fullers earth is mined from deposits of attapulgite. Attapul- gite is a clay mineral composed of monoclinic crystals of colloidal size, having a fibrous shape similar to that of asbestos. A sectional model of the attapulgite "molecule" is shown in Fig. 1. A single unit is about 18.0 A wide and 12.9 A high. The length of the molecule is variable, but this same molecular pattern is repeated to form needlework crystals, rather than flakes, as is characteristic of the montmorillonite crystals. Attapulgite has been assigned the following formula,&apos; although actually, the magnesia has been largely replaced by alumina: (0%) . (OH), • Mg, . Si, • Olp . 4H20. The fibrous nature of the mineral is clearly shown in the electron micrograph, Fig. 2. Although the deposits contain 5 to 30 pct quartz and carbonate minerals, impurities in the commercial products are held at a low level, principally by selective mining on the basis of oil decolorizing efficiency. The particle size distribution of this fullers earth has been estimated from settling rates, using sodium citrate as a dispersing agent.&apos; Since Stokes&apos; law only applies to spherical particles, the equivalent particle diameter calculated below is probably more nearly an index of diameter rather than length of the needlelike crystals: Eqnivalent Arbitrary Particle Distribution, Size Diameter Pci Classil3catian 0.05 mm 0.80 0.80 pct sand 0.05-0.02 mm 10.96 0.02-0.01 mm 9.65 42.10 pct silt 0.01-0.005 mm 11.40 0.005-0.002 mm 10.09 2-0.5 micron 10.61 0.5-0.2 micron 29.09 56.58 pct clay 0.2-0.05 micron 14.86 0.05 micron 1.96 The differential thermal analysis shown in Fig. 3 is unique and supports the theory that this is a distinct mineral species.&apos; ~ Other general properties of the mineral as shown in Table I.

Jan 1, 1952