Search Documents

By W. M. Duncan, F. S. Kendorski, C. V. Jude

After shotcrete had been in use for a short time al the Climax Mine of the Climax Molybdenum Co., Climax, Colo., it was noted that regular longhole undercutting blasts would severely damage or detach slusher drift shotcrete linings. If this were to be a usual occurrence, the widespread application of shotcrete would have to be reexamined or abandoned. Concrete drift linings are affected less by blasting because of occasional significant gaps between the placed concrete and rock and the greater thickness of poured-in-place linings. Research Project Organized A research project was organized to determine: 1) the seriousness of the problem, 2) more complete in-use shotcrete strength data, and 3) possible solutions.

Jan 12, 1973

By David M. Parkes, Junie Lindsay

A review of the movement of coal in water is undertaken from a practical rather than a theoretical view point. Installations are described in which coal is transported on gradients down to 2.5' and others which move coal at a water-coal ratio of 1:l by weight. The water cycle of the hydraulic mining system is discussed. In many applications this can be a closed circuit. The coal dewatering system is illustrated, making particular reference to the problems of storage of coal-water mixtures between the mine and the plant. Water treatment is done in thickeners down to 100 ppm which is normally sufficient for re-circulating through high pressure pumps and monitors.

Jan 1, 1978

By L. B. Bramlett, S. L. Reyher, G. G. Southard

The Archean (2.65 billion years) aged Canning Stock at Copper Mountain, WY, contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interibr of the stock. Post-Laramide development of supergene enrichment blankets occurred in 25-100 m (82-328 ft) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanism proposed for deposition of pitchblende are sulfides, hydro-carbons, bacteria, the water table, or some combination of these. Abundant tar-type organics appear to have preserved the enrichment blankets from degradation. Trace element and radio-metric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1983

By W. A. Backofen, M. L. Ebner, D. H. Avery

Slip on (11221 planes, which do not contain a close-packed direction, has been identified on crystals strained at —190°C. Evidence is also presented to show that (1071) pyramidal slip is a mode of deformation at 25ºC in a limited orientation range. PYRAMIDAL slip (l011) <1120> in magnesium at elevated temperatures has been established for some time.1-2 More recently, Burke and Hibbard reported this mode of deformation at 25"C, but their results were questioned by Craig.&apos; Also, as far as the present authors know, slip in magnesium on pyramidal planes of the second order, Type II (1122)) has not previously been reported, although Gilman"," identified (1122) slip in another hexagonal metal

Jan 1, 1959

By A. Boltax

H. Herman and M. E. Fine (Northzcesteriz University)—The author is to be complimented on the quality and completeness of his work. Of special interest to us was the exponent of time in the exponential rate equation, n = 0.28 ± 0.03, since it is consistent with results for the early stage of quench-aging in A1-2 at. pct Cu, n = 1/3, first determined in this laboratory."&apos; In that work we attributed the early kinetics to attraction of vacancy - solute atom complexes to the plate-shaped zone due to the strain field about the zone and the lowering in free energy. To our knowledge, Hirano et 1.&apos; were the first to

Jan 1, 1962

By G. Wranglen

On account of the possibility of isolating carbides in steel it is generally assumed that the electrode potential of iron carbide is more noble than that of ferrite.1,2,3,4,5 Differences from 0.032 V1 to 0.4 V4 have been recorded. However, it is important to realize that the more noble behavior of cementite in relation to ferrite is not an issue of thermodynamics but of reaction kinetics. Theoretically, cementite is less noble than ferrite, which is a direct consequence of its thermo-dynamic instability. With the value ?F°298 = +4700 cal per mol for the free energy of formation of cementite6 it is easily calculated that the electrode

Jan 1, 1950

US 4,201,749-In the Bayer process production of alumina wherein aluminum hydroxide is precipitated from a sodium aluminate solution for use as seed, sodium oxalate and caustic components are removed from the precipitate by washing it first with a washing liquor which is saturated with sodium oxalate but has little content of caustic, and secondly with hot water. Substantially no sodium oxalate is recycled, yet loss of sodium aluminate is minimal. K. Yamada, T Harato, and H Kato, assigned to Sumitomo Aluminum Smelting Co Ltd May 6, 1980 8 pp. (423-127). Filed. 5-8-79 (37,145) Priority. Japan, 5-8-78 (53/54,803). Same¬British 2,020,642, dated Nov. 21, 1979.

Jan 1, 1982

By R. A. Wyman

KYANITE schists in the Sudbury area have been generally described by Haw,1 who has also given particular information on preliminary treatment of three large samples from Dryden township, Ontario.2 Kyanite, garnet, biotite, quartz, and feldspar comprise the main ingredients of this ore. Kyanite is the valuable mineral. About 5 ½ tons of -35 +200 mesh product, made by dry rod milling, screening, and separation on the Exolon magnetic separator, were available for treatment by flotation. Magnetic separation had effectively reduced garnet and biotite so that flotation feed consisted essentially of kyanite, quartz, and feldspar, the kyanite content averaging 32 pct and representing about 86 pct of the kyanite in the original ore.

Jan 1, 1958

By T. R. Ingraham

The thermal decomposition of Nickel (II) sulfate was examined by determining the total pressure of SO3, SO2, and O2 developed over a sample when it was heated in an evacuated system fitted with a Pyrex-bellows mercury manometer. The equilibrium pressures were combined with previously published data on the oxide and sulfide systems to establish a predominance volume diagranz for the Ni-S-O system over the normal range of roasting temperature and gas composition used in the treatment of nickel minerals. The protective coating of NiSO4 which forms on the oxide during roasting, and which causes the sulfation reaction to almost cease, may be disengaged readily by temperature cycling. When nickel sulfide is roasted in air, either nickel sulfate or nickel oxide may be formed by altering the experimental conditions. Because of the differing stabilities of various metal sulfates and oxides, possibilities exist for separating some of the constituents of mineral mixtures by the technique of selective sulfation and oxidation roasting. The experimental information required to make reasonable predictions of the possibilities of this technique is incomplete and, in some cases, in conflict. As part of a general program of providing some of the required information, a study EXPERIMENTAL Materials, Apparatus, and Procedure. Fisher certified reagent-grade nickel sulfate hexahydrate was used in the source material for both nickel sulfate and nickel oxide. The manufacturer&apos;s analysis indicated: 0.001 pct Fe, 0.005 pct Cu, 0.003 pct Co, 0.001 pct C1, other 0.15 pct. The material was dehydrated, before use, by heating at 420°C for 5 hr. The oxide was prepared by roasting the sulfate in an open tray in a muffle furnace for 10 hr at950°C. Preliminary experiments which were made by thermogravimetric analysis and X-ray diffraction analysis established that only one crystal form of nickel oxide and one of nickel sulfate were involved in the equilibrium shown in Eq. [I]. The apparatus used in the experiments was described previously.1,3 The main feature is a corrosion-resistant, flexible Pyrex bellows which is used to protect the mercury in a u-tube manometer. Before a run was begun, the apparatus was washed thoroughly with hot hydrochloric acid and water and dried by heating under vacuum. The mixed sulfate -oxide sample was contained in a platinum bat rest-

Jan 1, 1967

By H. W. Mead, C. E. Birchenall

SELF-DIFFUSION of iron in austenite is a process which may play a significant role in some of the practically important reactions which occur in solid irons and steels. It also provides a system in which the interaction of vacancies on substitutional sites and atoms in interstitial positions may be investigated. For both purposes, accurate values of the diffusivities are required. Two sets of previous measurements exist, each containing features which require checking. In the course of an investigation to determine the rate of diffusion of iron in certain steels, Garwick and Rosenqvist&apos; measured the self-diffusion coefficient of iron in a 0.10 pct* C steel and obtained a dicated that while at lower temperatures D increased with increasing carbon content, at the higher temperatures it first increased and then decreased. At the same time the activation energy decreased linearly from a value of 69,000 cal per g-atom for pure iron to 33,000 cal per g-atom at 1.06 pct C. This rapid decrease in activation energy implies that iron at higher temperatures within the austenite range would diffuse more slowly in high carbon steels than in steels of lower carbon content. Experimental Procedure The radioactive iron used in this work was obtained from Oak Ridge National Laboratory. The unit consisted of about 1 microcurie each of Fe7 and Fe It was allowed to decay for two years. At the end of this time most of the Fe with a half-life of 46.3 days, had decayed, while most of the original Fe(half-life 2.91 years) still remained. The iron as chloride was extracted into an ether layer, using the method of Ashley and M~rray. After evaporation of the ether the iron chloride was dissolved in 250 ml of aqueous solution containing 2.4 gpl Fe. The compositions of the steels used are listed in Table I. Disks of ¾ in. diam and about ¼ in. thick were machined from these steels for use in diffusion couples. The disks were surface ground on both sides to ensure parallel opposite faces. One face of each disk was polished through 000 emery paper. Half of the prepared disks were plated with radioactive iron. For this, 1 ml of the radioactive iron

Jan 1, 1957

By Robert D. Thomson

LISTED among strategic and critical minerals for stockpiling, mica is an important raw material in electronic and electrical equipment industries. Each year large quantities are consumed in the manufacture of television and radio tubes, radar sets, generators, transformers, electric toasters, and irons. Crude mica, which comes from the mine in crystals or in rough books of various shapes and sizes, is known as run-of-mine or book mica. Structural imperfections, impurities, rough edges, and defective laminae are removed by cobbing, rifting, and trimming to produce a marketable block mica or film mica.&apos; After the rough books have been hand-cobbed to remove adhering rock, dirt, and crushed or defective mica they are rifted, or split. In the U.S. a straight-bladed knife is generally used for rifting. Products of this operation are classed broadly as untrimmed sheet mica and scrap. Sheet mica is any relatively flat piece sufficiently free from physical defects to be cut or stamped into specified shapes for industrial use. Sheet mica is classed as block, film, and splittings. Block mica is not less than 0.007 in. thick with a minimum usable area of 1 sq in. Film mica is split from the better qualities of block mica to groups of specified thickness ranging from 0.0012 to 0.004 in. Splittings are sheets with maximum thickness of 0.0012 in. and minimum usable area of 3/4 sq in. As virtually no mica splittings are produced in the U.S., they will not be discussed in this report. Small, low quality block is subdivided as punch and washer. Punch mica is thumb-trimmed material large enough to yield a circular disk of at least 11/2 in. diam for stained quality mica and 1 1/4 to 2 in. for clear quality. Poorer lots, often referred to as washer mica, are also included in the general term punch mica. Trimming, the next step in processing sheet mica, removes broken and ragged edges, loose scales, and other major imperfections. Trimming may be done with a knife, sickle, shears, or fingers. In the U.S. it is usually done with a 3-in. linoleum knife to obtain a bevel-edged cut. If ragged edges are broken off with the thumb and fingers, the mica is called thumb-trimmed. Full-trimmed is rifted mica trimmed on all sides with all cracks, reeves, and

Jan 1, 1957

By William Hague, Robert H. Bedford

The objects of this paper are: 1. To give cost data on drilling obtained at the North Star mine in California; 2. To describe the methods of testing drills employed there, giving the results of shop tests, and the correlated data obtained underground; 3. To demonstrate that these tests form a satisfactory basis upon which to judge rock drills. The rock at this mine is either close-grained diabase in the upper levels, or tough grano-diorite in the lower levels. The vein, which has an average dip of 23", consists of about 5 ft. of " formation" lying between walls of unaltered country rock. Of the 5 ft., solid quartz and stringers make up 18 in. of pay ore. The formation, which consists of but slightly altered country rock, is almost as hard as the unaltered walls. From 4 to 44 ft. is sent to the mill. One-third of the holes are drilled in the quartz; two-thirds in the formation. The holes are about 4 1/2 ft. deep and break on the average of 1.15 tons per hole. The average number of holes per stope drill shift is at present 5.65. The number of drill shifts throughout the mine in 1913 was 18,679, and the cost of labor for drilling, power, supplies, upkeep of machines and air lines, tool sharpening, and distribution, amounted to 33 per cent. of total mining expense. To do this work there are in commission 43 No. 12A, three No. 17V and eight No. 16V Waugh stopers, three Jackhamers, two Waugh pluggers, and 17 No. 8 and two NO. 7 water Leyners. For the past three years a record has been kept of the repairs on each machine and number of shifts operated by it. The figures given in Tables I and II for the cost of repairs per drill shift have been taken from this record. The underground air pressure is about 90 lb. The air consumption per drill shift was measured by aerometers. The leakage of pipe lines between compressor and meter is not included. From the number of pieces of steel sharpened for each type of drill during the year the average used per drill shift has been ascertained. For other supplies the figures given represent a year&apos;s average.

Jan 1, 1915

By J. E. Warren

In their analysis of Eqs. 29 and 30, the authors correctly deduce the following behavior limits for the "differential capacitance model". 1. When the rate group a is sufficiently large, the model reduces to that implied by Eq. 1, i.e., the simple convection-diffusion model. 2. When the rate group a is sufficiently small, the model reduces to that implied by Eq. 1 with 1 replaced by 1, i.e., the simple convection-diffusion model with a total pore volume equal to that occupied by the mobile fluid in the original model. Unfortunately, the authors&apos; solution, Eq. C-1, to the transformed versions of Eqs. 29 and 30 does not exhibit the same limiting behavior. For example, as a approaches zero, Eq. C-1 reduces to the solution to Eq. 1 or, equivalently, the solution to Eqs. 29 and 30 for sufficiently large values of a. Therefore, it can be concluded that Eq. C-1 is not a general solution to Eqs. 29 and 30; this conclusion can be easily verified by substitution. I suggest that the correct form of Eq. C-1 is the following: It is generally realized that accounting for dispersion effects is an extremely tricky business; therefore no one should criticize the pragmatic approach of Coats and Smith who proceeded by accessible theory, made use of some available phenomenology, and who then took the trouble to check the consequences, against their own carefully undertaken experimental results. Here I should like to defend three assertions: (1) Coats and Smith copy the error of previous authors in the formulation of the so-called simple diffusion model (which error is then retained in their differential capacitance model); (2) improving the fit between data and the predictions of an arbitrary model by increasing the number of parameters is a triviality unless the parameters are disposable by being independently determined; and (3) existing experimental procedures lack sufficient resolution to clarify some current theoretical uncertainties. Taking first the view that all theoretical approaches (whether constructed by statistical, finite difference, or continuum arguments) tend to reduce to the same model form as fixed by the number and nature of the disposable parameters, one notices that the "finite-stage" model of Deans1 is equivalent to the Coats and Smith so-called differential capacitance model for the pertinent case where a

Jan 1, 1965

By R. R. Hart, B. C. Wonsiewicz, G. Y. Chin

In recent years there has been increased miniaturization of electromechanical devices to keep pace with current trends toward smaller electronic components. A major problem facing the designer, however, is the higher stresses encountered by the material as a result of shorter springs. Hence an improvement in the elastic limit, as approximated by the 0.01 pct offset yield strength, would be highly desirable. An increase of 25 pct in the yield strength, for example, will permit a 20 pct reduction in both the length and thickness of a cantilever-type spring while maintaining the same compliance. One technique of improving the yield strength that has received little commercial attention is crystal-lographic texture strengthening.1,2 Texture strengthening is expected to be most beneficial in materials of hcp structure, but considerable gain can also be expected in cubic materials. A wire with a (111) fiber texture, for example, is expected to be 20 pct stronger than randomly oriented material, and 50 pct stronger than wire with a (100) fiber texture.293 For sheet specimens with a {110}(112) texture, characteristic of many heavily rolled fcc alloys, the (111) transverse direction is expected to be the maximum yield strength direction, about 20 pct higher than that in the (112) rolling direction.&apos; In addition, the (111) direction is the direction of maximum modulus of elasticity for most cubic alloys. A large value of the elastic modulus could be desirable in designs where stiffer springs are required. To test the above idea, a 0.090 in. (-2.3 mm) thick commercial grade A (5 pct Sn) phosphor bronze sheet, a widely-used material for relay springs, was rolled from the spring-tempered condition (60.5 pct reduction) to various additional reductions up to a total reduction of 95 pct. Subsequently, additional material was obtained with a total thickness reduction of 97.3 pct Standard tensile specimens were prepared from the sheet material with the tensile axis parallel to and at 90 deg to the rolling direction. Tests were run on an Instron testing machine at a strain rate of about 0.050 min-l. Textures were determined by the use of the reflection pole-figure technique. Data were obtained using nickel-filtered CuKa radiation and with the aid of a Siemens pole figure goniometer. The X-ray pole figure studies show an incrzasing development of the texture toward the {110}(112) ideal

Jan 1, 1970

By G. W. Tracy

The material balance equation has been used for many years by engineers to determine reservoir performance. The use of this equation in general has been twofold: first, to determine the oil-in-place in a reservoir; and second, to predict the future performance. The Schilthuis form of the material balance equation, or one equivalent to it, has been used by many of the engineers. The use of the Schilthuis form in predicting future performance has proved to be laborious in that one generally must make several estimates at each step of the trial and error calculation before arriving at a check of the oil-in-place. A method is presented for expediting the calculations. The Schilthuis form of the material balance has been rearranged into a more useable form. In using the material balance to predict the future performance of a reservoir, it has become common practice to estimate the incremental oil production for each step of the calculation which corresponds to a given pressure reduction. Instead of estimating the incremental oil production, the method outlined in this paper better lends itself to estimating the instantaneous gas-oil ratio. A check of oil-in-place is more easily accomplished by estimating gas-oil ratio since it is less sensitive to small inaccuracies. This method incorporates the same self-checking feature inherent in the Schilthius form. DEVELOPMENT OF SIMPLIFlED EQUATION In the development of the simplified equation, the Schilthuis form of the material balance equation will he used. Substituting in Equation 1 for and rearranging terms In Equation 2, the cumulative oil production (n) is multiplied by a factor which is uniquely a function of pressure. Also, the cumulative gas production (G) and net water influx are also multiplied by factors which are a function of pressure alone. These factors are called and are defined as follows: Using these factors, Equation 2 becomes The equation in this form is easier to manipulate mathematically than any of the previous forms which, have been used. Sources of data for the pressure factors are a bottom-hole fluid analysis and the ratio of initial gas cap volume to oil volume in the reservoir. AID IN DETERMlNING THE ORIGINAL OIL-IN-PLACE Each of the curves and +, have a similar shape. Each is infinite at the bubble point pressure. As lhe pressure is reduced below the bubble point, the

Jan 1, 1956

By P. Schwarzkopf, J. H. Brophy, J. Wulff

A constitutional diagram has been proposed for the tantalum-rhenium alloy system. Rhenium dissolved in tantalum up to 48 wt pct, and the maximum solubility of tantalum in rhenium is 5 wt pct. Intermediate x and s phases were found. X-ray diffraction, metallography and melting points were employed. SEVERAL investigators have described the phases present in the tantalum-rhenium alloy system, but no detailed account of the phase diagram prior to the present investigation appears to be available. Greenfield and Beck&apos; reported the solubility of 48 to 54 at. pct Re in tantalum, a s phase at 41 at. pct Ta, and x phase isomorphous with a Mn from 37 at. pct Ta to less than 25 at. pct. They employed as-arc melted specimens and heat treatments at 1200 °C lasting 72 hr.2 Duwez3 reported the existence of a a phase at the composition Re3Ta2. Niemiec and Trzebiatowski4 observed a lattice parameter a = 9.69A, for the x phase at a composition Ta7Re22, but no s phase. Savitiski and Tylkina5 have shown a hardness maximum at the composition 40 at, pct Ta and a somewhat lower plateau from 35 to 10 at. pct. Knapton6 indicated results similar to those of Greenfield and Beck.&apos; The present investigation describes the phase relationships in the tantalum-rhenium alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURE Commercial 99.7 pct Ta powder from Fansteel Metallurgical Corp. and 99.9 pct Re powder from Chase Brass and Copper Co. were used for alloy preparation. The powders were weighed to desired nominal compositions and then pressed without binder into compacts weighing 5 or 10 g. The compacts were arc-melted six times on alternate sides on a water-cooled copper hearth using a nonconsumable tungsten electrode in an atmosphere of titanium gettered helium, at a pressure of 500 mm Hg. In most cases this procedure yielded alloy buttons of satisfactory homogeneity. A series of alloy specimens were analyzed wet chemically for use as standards for X-ray fluorescence. All specimens were analyzed by fluorescence and the results showed that the compositions differed by less than 3 pct Re from the original as-weighed nominal composition.* On the basis of self-

Jan 1, 1961

By W. B. Lilienthal, J. C. Melrose

The application of Bingham&apos;s law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham&apos;s law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn&apos; have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham&apos;s law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,&apos; following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham&apos;s integration of Bingham&apos;s law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning&apos;s equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,&apos; the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham&apos;s equation is defined

Jan 1, 1951

By J. C. Melrose, W. B. Lilienthal

The application of Bingham&apos;s law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham&apos;s law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn&apos; have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham&apos;s law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,&apos; following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham&apos;s integration of Bingham&apos;s law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning&apos;s equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,&apos; the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham&apos;s equation is defined

Jan 1, 1951

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.&apos; In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.&apos;s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By D. C. Hilty

It has long been known that in melting high-chromium steels, some of the carbon might be oxidized out of the melt without excessive simultaneous oxidation of chromium, and that higher temperatures favor retention of chromium. The advent of oxygen injection as a tool for rapid decarburization of a steel bath permits significantly higher bath temperatures, and it was quickly recognized that the use of oxygen injection facilitated the oxidation of carbon to low levels in the presence of relatively high residual chromium contents. Up to the present time, however, specific data pertaining to the chro-mium-carbon-temperature relations in chromium steel refining have not been available. Individual steelmakers have evolved practices more or less empirically, but there has been very little real basis for predicting how effective any given practice can be in permitting maximum oxidation of carbon with minimum loss of chromium. The current investigation, therefore, was undertaken in an effort to establish the fundamental carbon-chromium relationship in molten iron under oxidizing conditions. As reported below, the equilibrium constant and the influence of temperature on that constant have been derived for the iron-chromium-carbon-oxygen reaction in the range of chromium steel compositions with what appears to be a fair degree of precision. The practical application of the result will be obvious. Experimental Procedure The laboratory investigation was carried out on chromium steel heats melted in a magnesia crucible in a 100-lb capacity induction furnace at the Union Carbide and Carbon Re- search Laboratories. The charges for the heats consisted of Armco iron, low-carbon chromium metal, and high-carbon chromium metal, the relative proportions of which were calculated so that the various heats would contain from approximately 0.06 pct carbon and 8 pct chromium to 0.40 pct carbon and 30 pct chromium at melt-down. When the charges were melted, the bath temperatures were raised to the desired level, and the heats were then decarburized by successive injections of oxygen at the slag-metal interface through a ½-in. diam silica tube at a pressure of 30 psi. The duration of the oxygen injections was from 30 sec to 2 min. at intervals of approximately 5 to 30 min. It did not appear that length or frequency of the injection periods had any significant effect on the results; cansequently, no effort was made to hold them constant and they were controlled only as was expedient to the general working of the heats. Between successive injections, the heats were sampled by means of a copper suction-tube sampler that yields a sound, rapidly-solidified sample representative of the composition of the molten metal at the temperature of sampling. This sampling device is a modification of the one described by Taylor and Chipman.1 An attempt was made to vary bath temperatures between samples, but it quickly became evident that, unless the variations were small or unless the new temperature was maintained for a minimum of 15 min. during which an injection of oxygen was made in order to accelerate the reactions, a very wide departure from equilibrium resulted. For most of the runs, therefore, temperature was maintained relatively constant at approximately 1750 or 1820°C. A few reliable observations at other temperatures, however, were obtained. Temperature Measurement The high temperatures involved in this investigation were measured by the radiation method, utilizing a Ray-O-Tube focused on the closed end of a refractory tube immersed in the metal bath. The immersion tubes employed were high-purity alumina tubes specially prepared by the Tona-wanda Laboratory of The Linde Air Products Co. These tubes were quite sturdy under reasonable mechanical stress at high temperature. They were unusually resistant to thermal shock, and chemical attack on them by the melts was slow. With care, it was found possible to keep these tubes continuously immersed in a heat for as long as 5 hr at temperatures up to 1850°C, before failure by fluxing occurred. The Ray-O-Tube—alumina tube assemblage was similar to those supplied commercially for lower temperature applications. In operation, the alumina tube was slowly immersed in the molten metal to a depth of approximately 5 in., and the device was then clamped solidly to a supporting jig where it remained for the duration of the run. A photograph of the equipment, in operation with Ray-O-Tube in place and oxygen injection in progress, is shown in Fig 1. When in position in a heat, the instrument was calibrated by means of an immersion thermocouple and an optical pyrometer. For calibration through the range of temperatures from 1500 to 1650°C, a platinum -platinum + 10 pct rhodium thermocouple in a silica tube was immersed alongside the alumina tube. Output of the Ray-O-Tube in millivolts and the

Jan 1, 1950