Search Documents

By McHenry Mosier

This paper describes the practice in diamond drilling blast holes and discusses the relative merits of this method as compared with drilling by percussion rock-drills at eastern magnetite mine A. The rooke that were drilled included: (1) Gneiss; (2) sohist; (3) crystalline limestone; and (4) granular masses of magnetite. The principal stoping methods were: (1) Sublevel open stoping and (2) inclined room-and-pillar. Diamond drilling was used in the sublevel stopes and in some of the large pillars in an old section of the mine. Experimental work on diamond drilling blast holes began in 1943. Drill- ing proved difficult owing to the occurrence of fingers of extremely hard barren rock in the magnetite ore. All diamond drilling was contracted to a firm that furnished everything necessary for drilling except compressed air and water. In most instances the diamond-drill machine is clamped directly to a 3.5-inch column to reduce vibration. For drilling in floor pillars in open stopes, the drill was set on a demountable, sectionalized steel, frame with four legs carrying a 20-foot, 3.5-inch, extra-heavy pipe. "Both coring and noncoring bits were tried. In holes drilled with a cor- ing bit, the core was ground into sludge as the bit advanced so that it was unnecessary to delay drilling for pulling core. Data on tests with several types of bits are given as well as some oper- ating results. A direct comparison of costs between diamond drilling and percussion drilling was not available. The advantages of diamond drilling blast holes at mine A included: (1) Safer working conditions in open stopes. (2) The recovery of additional ore. (3) A reduction in the amount of stops development.

Dec 1, 1946

By Philip C. Tully

[This bibliography contains 3,655 different citations to technical and scienfic literature on helium and alpha-particles, abstracted by 13 abstract service iblicatlons during 1964. Multiple subject classification increases the total number of entries to more than 5,800. Helium citations are listed by 22 major assifications, alpha-particles by 12]

Jan 1, 1970

By S. H. Ash

The paramount responsibility of Government is to protect the general welfare. One of the chief functions of the Bureau of Mines is to investigate and publicize methods of increasing safety and efficiency in mining operations. In an industrial civilization, energy resources constitute the foundation of a sound economic structure (14).4/ Coal is only one source of energy, but it provides more than half the energy consumed in the United States.

Jan 1, 1946

By D. C. Crowell, A. G. Loomis

Both Dimensional and Inspectional Analysis are developed from fundamental concepts , and dimensionless groups are derived which represent the viscous , capillary , and gravitational forces existing in two - phase , incompressible flow in petroleum reservoirs . It is shown how properly scaled models may be devised by means of the foregoing groups . Laboratory measurements with such models faithfully duplicate the behavior of the reservoir on a miniature dimensional and compressed time scale , and when all the pertinent variables are evaluated , the model is a most effective tool for the study of complex fluid displacements in the reservoir . Applying the Principle of Similitude , it is shown how dimensionally scaled models are applied to various types of reservoir displacements : ( 1 ) Oil displaced by water , ( 2 ) gas displaced by water , and ( 3 ) miscible displacement . The special case of water displacing gas by imbibition is analyzed , and it is shown that the dimensionally scaled model must be fabricated of sandstone rather than unconsolidated sand , which is generally used in such models . This report is intended to be a review and summary of the application of Dimensional Analysis to reservoir displacement problems for those who are beginning the study of this useful and interesting method .

Jan 1, 1964

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By John B. Gayle

The coking time has considerable influence on the throughput of a coke oven, and for this reason a large number of papers dealing with the relationship between coking time and the different operating variables have been published. Although all factors known to influence the coking time have been studied, agreement has not been reached on several questions.2/3 Therefore, it appears worthwhile to evaluate any data that become available during investigations of the carbonizing properties of various coals and coal blends. Because it is expected that reports covering several different phases of this problem will be forthcoming as additional data-become available, the following study of the relationship between coking time and bulk density represents a report of progress on the overall investigation of factors influencing the coking time in slot-type ovens. The practice of including coarse coal in the blend going to the ovens to obtain increased bulk densities is well known. Similar increases have been realized by adding small quantities of oil to the coal mix. Although it would appear that such procedures provide inexpensive methods for increasing the capacity of existing coke-oven installations, Ramsburg and McGurl4/ point out that this increase is possible only if the additional coal can be carbonized in the same coking time as regularly employed without using abnormally high flue temperatures. This statement is in substantial-agreement with the position of Auvil and others5/ and implies that any change in bulk density may be accompanied by a corresponding change in coking time. On the other hand, a recent review of proposed methods for calculating the time required for carbonization6/ includes a number of equations that completely ignore the effects of variations in bulk density.

Jan 1, 1954

By Sara Jane Boles

The purpose of this Bureau of Mines investigation was primarily to isolate and examine the effect of liquid content upon the apparent porosity and bulk density of compacts pressed from high-purity, fused aluminum oxide, and, secondarily, to study the actual mechanism by which the liquid content affects the bulk density. No attempt was made to approach the theoretical maximum density of the oxide by introducing additives, particle packings, or similar variables; instead this study is an intercomparison of the bulk densities obtained as functions of the water contents of the compacting mixtures. Water content was varied from 7 percent to 25 percent, on a total-weight basis. The data gathered indicated a well-defined optimum water content for obtaining minimum apparent porosity and maximum bulk density, under the conditions of the experiment. During the course of this study, a number of additional variables in the forming process were discovered and are introduced in this report, although a thorough evaluation was found to be beyond the scope of this present investigation.

Jan 1, 1963

By William H. Lewis

This paper describes the Bureau of Mines efforts in the research and development of a new and innovative mine lighting system which is based on fiber optics technology. The new lighting concept offers significant advantages over conventional systems in the areas of both safety and long- term maintenance costs. An overview of Bureau research into the problems and limitations of present-day mine lighting systems is also presented.

By K. J. Liles

The Federal Bureau of Mines conducts a comprehensive test program on clay and shale at the Tuscaloosa Metallurgy Research Center. All samples are subjected to standard preliminary ceramic tests, which include firing formed briquets at temperatures ranging from 1,000° to 1,250° C to identify firing range and colors, and quick-firing to determine bloating characteristics. Materials that shop potential as structural products are further tested after either extrusion or dry-pressing. If the quick-fire test is positive, bulk samples can be fired in a rotary kiln to evaluate their potential as light- weight aggregate A number of miscellaneous tests also can be conducted if requested. These tests determine properties such as refractoriness (pyrometric cone equivalency), oil-bleaching characteristics, oil absorbency, viscosity for drilling-mud applications, sand-bonding properties for foundry usage, and pelletizing characteristics.

Jan 1, 1977

By H. B. Hill

The discovery of the Oklahoma City field and its rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38,5.° A.P.I. gravity oil, and several months later was, completed at a depth of 6,624 feet, The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933

By G. A. Apell, E. G. Howe, S. W. Hazen

"INTRODUCTION As a small amount of manganese was produced from the Lake Valley mining district of Sierra County, N. Mex., during the First World War, the district was reexamined in March 1941 by John H. East, Jr., an engineer of the Bureau of Mines, as a possible source of manganese for use during the Second World War. Preliminary examination indicated a substantial reserve of 25 percent ore, so it was recommended that an exploratory program of mapping and sampling be undertaken by the Bureau.The program was started in the fall of 1941 and was completed the middle of 1942. The project 3/ was divided into two parts: The first, an underground sampling program, formed the basis for the second, or churn-drilling program. Mapping and sampling of old underground workings were begun in October and finished in November 1941, whereas churn drilling was begun in February and completed in June 1942."

Jun 1, 1947

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By A. G. Loomis

METHODS for measuring relative permeability as a valid function of saturation were compared by the. Bureau of Mines, using core samples from representative oil-productive California formations, from the Bartlesville sand in Oklahoma, and from synthetic samples. Measurements for gas-oil systems were made by steady-state dynamic, unsteady-state displacement and two stationary-phase methods. Measurements for water-oil systems were made by the unsteady-state displacement method. As the ratio rather than individual relative permeabilities is measured by the last method, three methods for calculating individual relative permeabilites from their measured ratio were compared for gas-oil systems and two methods for water-oil systems. Errors arising from capillary discontinuities, such as the end effect and stabilized-zone flow, are discussed and evaluated; possible errors rocs arising from turbulant flow are also examined. The inapplicability of non-steady-state methods for water-oil systems that are not definitely oil-wet is discussed in detail. Measurements of relative permeability to both gas and oil can be made quickly and accurately by the steady-state dynamic method when rates of flow of the two phases are sufficient to minimize the capillary discontinuity at the outflow end of the sample. At such rates relative permeability-saturation measurements are essentially independent of the rate of flow. The steady-state method wits modified by a dispersion section at the inflow end of the sample acid designated tie dispersed-feed method.

Jan 1, 1962

By C. Özgen Karacan

Gamma ray, density, sonic and core logs obtained from two boreholes drilled over a longwall panel in Southwestern (SW) Pennsylvania were analyzed for formation boundaries, log-derived porosities and densities and for rock elastic properties from sonic transit times. Gamma ray (GR) and density logs (DL) were analyzed using univariate statistical techniques and fractal statistics for similarity and ordering of the log data in depth. A Fourier transformation with low-pass filter was used as a noise elimination (filtering) technique from the original logs. Filtered data was tested using basic univariate and fractal statistics, rescaled range (R/S) and power spectrum (PS) analysis to compare the information characteristics of the filtered logs with the original data. The randomness of log data in depth was analyzed for fractional Gaussian noise (fGn) or fractional Brownian motion (fBm) character. A new prediction technique using radial basis function (RBF) networks was developed to calculate shear and Young?s moduli of the formations when sonic logs are not available. For this approach, the filtered logs were used as input to an RBF based upon a combination of supervised and unsupervised learning. The network was trained and tested using rock elastic properties calculated from the sonic log of one of the boreholes. The network was used to predict the elastic and shear moduli of the coal-measure rocks over a longwall coal mine in SW Pennsylvania. This approach demonstrated that it could be used for prediction of elastic and shear moduli of coal-measure rocks with reasonable accuracy.

Jan 1, 2009

By F. E. Griffith, C. H. SEELING

Cardox blasting is used widely in coal mines in the United States . A model of a Cardox blasting device was approved by the Bureau of Mines subject to certain conditions and limitations , and the approval was extended to other models from time to time . Certain special hazards are entailed in the use of Cardox as with explosives . One of these is flying shells . In some blasts , the Cardox shell is violently ejected from the borehole and flies like a projectile , frequently ricocheting off solid objects and striking points considerably off the line of its initial flight . Flying shells have been known to pierce the webs of structural - steel beams , to pass through both sides of allsteel mine cars , to be driven through stout hardwood timbers , to knock out timber sets , to damage loading equipment , and to break or short - circuit power lines . A considerable number of shot - firers and other workers have been struck by flying shells and killed or injured . Accidents from this cause , although not as frequent as other types of mine accidents , are usually serious , closely approximating accidents caused by blasting with ordinary explosives . The increasing number of such accidents prompted a Bureau of Mines field investigation of possible methods of preventing dangerously violent ejections of Cardox devices . This report contains pertinent data collected during the investigation and describes methods tested and discarded as well as the development and proof of an apparently satisfactory method .

Jun 1, 1943

By F. A. Rutledge

The Batesville district in north central Arkansas is one of the important sources of manganese ore and ferruginous manganese ore in the United States, with a history of production dating back to 1849. From studies by the Federal Geological Survey, it was recognized that the district probably still contains substantial reserves of low-grade ore. It was natural, therefore, that the deposits in this area should be among the first investigated by the Bureau of Mines under the Strategic Materials Act of June 1939, by which the Bureau was authorized to explore domestic deposits of strategic minerals, at that time designated as those of antimony, chromium, manganese, mercury, nickel, tin, and tungsten. The field work of the Bureau of Mines in the Batesville district was done in two distinct phases. Under project 308, active from August 1940 to June 1941, carbonate-oxide ores were investigated at five separate areas in which 100 trenches, test pits, shafts, and edits aggregating 4,364 linear feet were excavated and 839 samples were taken and assayed. Under project 323, in progress from February 1941 to January 1942, wad deposits were explored at 10 separate areas by 408 prospect shafts, churn-drill holes, and bucket-drill holes aggregating 23,680 linear feet from which 285 samples were taken and assayed. Processes for beneficiating the wad ores were investigated at ore-testing laboratories of the Bureau of Mines.

Jan 1, 1952

By T. M. Romslo

The Lake Shore property, located in the early 1880's, contains copper-bearing deposits that have been developed by surface excavations, underground workings, and churn-drill holes. Operation of the property ended in 1929 with a total recorded production of 280,000 pounds of copper. The property is near the foot of the Slate Mountains, which are made up mainly of probably the Pinal formation of pre-Cambrian age. In the mine area there are a few outcrops of granite, which is exposed over a large area east of the property. Other outcropping rocks on the property are limestone, quartzite, and diabase. The limestone and quartzite probably are the Mescal and Troy formations of pre-Cambrian and Cambrian age, respectively. The predominant copper mineral is chrysocolla, a hydrous silicate that occurs mainly as fracture filling in bedded schist. It is also, the principal copper mineral in the shear zone at the schist-granite contact and in limestone southeast of the main workings. Investigation of the Lake Shore property by the Bureau of Mines included both topographic and geologic mapping, exploratory drilling, and metallurgical test work. One diamond-drill, hole and five churn-drill holes were completed for a total of 2,872.5 feet. Drilling started January 19 and was completed May 13, 1949.

Jan 1, 1950

By T. M. Barczak

This U.S. Bureau of Mines report investigates shield mechanics and component stress development in a two-legged longwall shield for unsymmetric canopy and base contact configurations. Previous studies analyzed shield behavior for symmetric contact configurations. The goals of these efforts are to improve longwall support selection and design. This study provides vital information that will help develop improved procedures for performance testing of longwall supports and will benefit future research to improve support design through stress optimization and evaluation of failure mechanisms. Combinations of six canopy (three symmetric and three unsymmetric) and six base (four symmetric and two unsymmetric) contacts provided a total of 36 configurations for evaluation. Of these 36 configurations, 10 were eliminated because of fixture limitations or shield instability. Controlled vertical and horizontal displacements were applied by the Bureau's mine roof simulator to the remaining 26 configurations. Component responses were determined from pressure transducer and strain gage instrumentation in order to identify contact configurations and boundary displacements that produced maximum loading in each of the support components. This report describes these test results and provides conclusions relevant to critical contact configurations for performance testing of longwall supports.

Jan 1, 1990

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966

By N. C. Dunham

"The Bureau of Mines exploratory work on the Bear Lodge, Wyo., fluorite property wider the strategic minerals Program was completed in November 1944. Exploration consisted of surface trenching, shaft sinking, and drifting at shallow depth. Doak C. Cox of the Federal Geological Survey visited the area during the latter part of 1944 and napped the Bear Lodge property.The Bear Lodge property is situated in the Black Hilts National Forest in eastern Crook County, Wyo., 6 miles north of the community of Sundance (fig. 1). Sundance is 29 miles northwest of Upton, Wyo., a station on the Chicago, Burlington, & Quincy Railroad and 43 miles southwest of a siding on the Chicago & Northwestern Railroad, 3 miles south of Belle Fourche, S. Dak. U. S. Highway 14 passes through Sundance in an east-west direction. Sundance may be reached from the south over U. S. Highway 85 and Wyoming State Highway 585.The Bear Lodge property i a situated in the Boer Lodge Mountains in secs. 15, 22, and 23, T. 52 N., R. 63W., 6th P.M.The topography in the vicinity of the fluorite deposits consists essentially of rounded hills which slope gently to the valley floors. Near the north end of the Property the terrain steepens locally, and the canyon walls are Precipitous along the courses of several streams. There is an adequate supply of water and native timber for mining purposes. The average elevation near the deposits is 5,700 feet.The climate of the region is relatively moderate. The summers are usually warm, with frequent rainstorms. Temperatures often fall below zero during the winter months. Snowfalls are moderate to heavy.Fluorite occurrences in the Bear Lodge area have been known since 1914; however, fluorite was not discovered on the Bear Lodge property until 1943, when prospectors working on a nearby manganese deposit found fluorite mineralization in the limestone. No production has been recorded from the property."

Apr 1, 1946