Search Documents

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

By Thierry Bernard, Philippe Dozohne

May 13th, in the back country of Nice @arice) collapsed a complete piece of mountain, cutting the RN 2085 and destroying a part of Valabfre’s viaduct. The fist inspections of the site showed that materials had broken loose from surrounding cliffs, The geologists discovered that a block of several thousands of m3 remained suspended in cliff and that it presented a risk raised of gliding. Decision to destroy it by blasting in one blast was there taken by the French department’s council of the Maritime Alps. A race against the clock engaged. Indeed, the RN on 2085 is the main axis connecting the village of Saint Etienne de Tinee and the resort station of ISOLA in the centre of Nice

Jan 1, 2001

By Marcus Neves, Eventomar Junior, Adilson Castro, Leandro Silveira, Sérgio Augusto

The collapse of the Vale S.A. mining tailings dam in 2019, a tragic event that shook Brazil and the world, had consequences that transcended the immediate pain and devastation. Among them, the suspension of rock blasting activities in several mines in the Quadrilátero Ferrífero region of Minas Gerais, Brazil. This measure, taken as a precaution and with the aim of ensuring the safety of nearby geotechnical structures and the population, had a significant impact on the mining production chain. To overcome these challenges and resume blasting activities in a safe and sustainable manner, the mining industry has been dedicated to developing and improving solutions. One of the promising alternatives is the signature hole technique, used in conjunction with attenuation laws. The complex geology of the Quadrilátero Ferrífero, with lenses of compact ores immersed in friable materials, the presence of discontinuity families, and the emergence of geological faults, requires detailed analyses and specific adaptations of the signature hole technique and constant monitoring of the vibrations to calibrate the attenuation laws to ensure compliance with permissible limits and safety of the operations. To demonstrate the methodology, a case study in Abóboras Mine was described. Additionally, the challenge of achieving the desired level of production while controlling vibration and slope damage has driven the development of new charging and timing techniques. To address this challenge, a comprehensive approach was undertaken. A substantial database containing more than 4,000 registers of blasting-induced vibration events from 520 blasts was meticulously compiled from 2020 to 2023, 6 different attenuation laws were established and continuously calibrated with 99.3% of compliance regarding permissible limits of vibrations. The successful implementation of these actions allowed for the resumption of blasting, increasing production from 10 million metric tons to 43 million metric tons per year assuring sustainable operation.

Jan 21, 2025

By Aiden Carey, Jim Kennedy

During December 2007, Lake Cowal Gold Mine located in New South Wales, Australia experienced a significant pit wall failure. The wall failure resulted in the deposition of a large quantity of saprolite consisting largely of clays and lake bed sediments to the bottom of the Phase 1 open pit mine. This wall failure ultimately buried two loaded blast patterns.

Jan 1, 2011

By Tyler Acorn, Tristan Worsey

A dozer operator at a surface gold mine accidentally drove a D10 off the side of a highwall. The blade of the dozer caught on the lip of a catch bench 60 ft. (18.3 m), down stopping its descent. The operator scrambled to safety in fear that the dozer would not hold.

Jan 1, 2014

By Tony Rorke, Tamara Wiseman

Due to the advancements in technology it becomes easier to obtain accurate measurements for mining, quarry, and construction operations even in the most remote places. The use of off-the-shelf photogrammetric imaging technology and unmanned aerial vehicles (UAVs) are becoming more common in the mining industry for blast design and surveying. Pattern optimization, face profiles, pre and post blast volumetric, stockpile measurements and mine mapping are all areas where these technologies can be used with ease.

Jan 1, 2015

By Evan Boone, Peter Bellairs

A technical services visit was conducted to determine the initial parameters to successfully presplit several benches for an input crusher installation at the Wolffdene quarry. The paper details the preliminary design utilising both detonating cord only and specialised presplit product charges and compares these to the final designs utilised based on site experience. The role of accurate drilling, explosive loading and geology in obtaining successful cost effective presplits is highlighted.

Jan 1, 1998

By Selamawit Asfaw, Mohamad Sharif

In recent years, the use of modal analysis has increased to include many different aspects of the construction industry. Computer modal analysis can be used in determining the dynamic properties of a structure by mathematical equations and knowledge of the structure’s physical properties. This technique can now be used to predict the level of vibration induced by blasting on adjacent structures. Ground vibration induced by buried explosives is a major concern for contractors when excavating near utility pipelines such as gas and water lines. The size limitations placed on easements causes the necessity of additional utility lines to be placed in close proximity to existing lines. Through the development of computer models of the pipe, stress analysis can be performed prior to blasting. Based on the calculated dynamic properties (natural frequencies and modal shapes) and the maximum allowable displacements and stress levels (which are established by the pipe manufacturer) the allowable maximum charge weight per delay can be selected for the blast. The selected maximum charge weight per delay will ensure that the resulting pipe peak particle velocity level is within 95% confidence. This means, statistically, there exists a 95% probability that the actual pipe peak particle velocity would be less than the predicted value. The pipe is then instrumented with vibration measuring sensors to ensure that vibration levels are within the allowable maximum pipe strength. In conclusion, this technique can assist the engineers and blasters, to establish the proper blast design. It allows for safe and efficient installation of additional utility lines adjacent to existing lines. This technique can also be applied to predict the structural response to blasting induced vibration for a variety of complex structures. A detailed explanation of this technique, as well as an example of application including formulas used for this technique will be provided in this paper.

Jan 1, 2000

By Steven D. Knudsen, Dale S. Preece

The spherical element computer code DMC (Distinct Motion Code) used to model rock motion resulting from blasting has been enhanced to allow routine computer simulations of bench blasting. The enhancements required for bench blast simulation include: 1) modifying the gas flow portion of DMC, 2) adding a new explosive gas equation of state capability, 3) modifying the porosity calculation, and 4) accounting for blastwell spacing parallel to the face.

Jan 1, 1992

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By W. L. Saunders

RBH Note: In the early days of drill & blast tunneling the jobs utilized large crews of drillers and muckers. Advance per round was limited (typically around four feet) but two rounds per 8-hour shift were expected, around the clock. The scene after a shot must have been chaos, with the muckers expected to quickly make space for the drill setup. Makes one wonder how much time was allowed for the smoke and fumes to clear. Note the headgear of the tunnelers.

Jan 1, 2011

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lie Company’s new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By J Silva Castro, W C. Wedding, B T. Lusk, J Calnan, E G. Morris

The emergence of electronic detonators for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. This paper reports on an independent study quantifying the accuracy of two electronic and two non-electric systems in which 674 detonators were tested. This research aimed to determine the accuracy of commercially available electronic detonators as compared to non-electric shocktube systems. Each system was tested over the viable ranges of delays available. Statistical models were then applied to quantify the scatter present in each system. Suggestions for the use of electronic detonators are made from the findings of this work. This work was made possible through funding from the United States Department of the Interior Office of Surface Mining Reclamation and Enforcement.

Jan 1, 2012

By Yong Pan, Purushotham Tukkaraja

Block caving is a preferred underground mining technique due to its high production rate and low operation cost. Before its final step into a mature caving system using gravity to break rock, drilling and blasting are required to form drawbells to connect the production level and undercut level and induce the initial caving propagation in undercut level. A large amount of toxic fume generated by blasting activities poses a big threat to people working in a confined environment and ventilation is assumed to be the most economical and efficient way to deal with this issue. Past research shows that it’s common to use traditional methods like using a formula or using numerical method (Computational Fluid Dynamic (CFD)) simulation to predict re-entry time after each blasting, but it fails to consider the percentage of toxic fume entrapped in muckpile, which could reach up to 70%. In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

By Yong Pan, Purushotham Tukkaraja

In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

Feb 1, 2020

By David G. Paton

"Electromagnetic surveys were conducted at the BXL Bulk Explosives Limited Mixing Plant andsurrounding area to characterize runoff from the site and possible impacts of salinity. The BXL Plant is located at the edge of a depressional area and any escape of soluble ions, such as nitrates, would have ended up in the slough to the west of the plant. Two electromagnetic (EM) instruments were used in the survey. A Geonics EM 3 1 was used in October 1997 and in June 1998, a new multifrequency instrument, a GSSI GEM 300 was also tested. Both instruments were individually mounted on a plastic sled with Teflon runners and towed with an ATV quad. Position was determined using a Trimble Pro XL global positioning system (GPS) with a real time correction mode Landstar receiver for an accuracy of about *l m. Both GPS and EM instruments were set to collect data at 1 second intervals. The quadrature maps for both instruments showed essentially the same information, namely of very high conductivity, appearing to emanate from the mixing plant. The levels of conductivity were highest where the saline water appeared to pool, at the southern end of the slough. Soil sampling locations were identified from the EM maps and navigated to using the real time GPS. Composite samples were collected by hand using a Dutch auger, from two locations, in increments of O-1 5, 15-30, 30-60 and 60- 90 cm. The analysis of the soil samples indicated a complete absence of nitrate or ammonium ions; the major anion was sulphate, indicating naturally saline subsoil conditions. The GEM 300 made the collection of data more efficient, as only one pass was required to collect the data from four depth intervals. The EM survey combined with the real time GPS allowed rapid characterization of the site with respect to soil salinity and proved to be cost-effective for Phase l/ Phase 2 site assessments and targeting sampling locations."

Jan 1, 1999

By Shazad Hosein, Bill Birch, Catherine Johnson, Toby White, Liam Bermingham

Air overpressure (AOP) from blasting can give rise to a significant number of blasting complaints from residents living adjacent to blasting operations from mines, quarries or civil engineering projects. High amplitudes of AOP are usually associated with the lateral movement of a vertical free face, but it can also be caused by the upward lifting and the venting of gases through the surface of the blast area.

Jan 1, 2018

By Ben Barrett

Dangerous goods, known as hazardous materials in the USA, are subject to special controls during transport to ensure the safety of the public. Dangerous goods are divided into nine classes, and Class 1 is devoted to explosives. Unlike storage or manufacturing, explosive transportation crosses the political boundaries of localities and nations, and its regulation must be centrally managed to avoid duplicate costs of complying with multiple regulations. Additionally, the transport of dangerous goods occurs by four different modes – highway, rail, vessel and air. While each mode has differences which must be addressed, the fundamental principles of classification, packaging, hazard communication and documentation remain the same. When a shipment travels by multiple modes and across borders, consistent regulations become paramount to cost efficiency. This is a common occurrence in the growing global economy.

Jan 1, 2010

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

By Frank Hirthammer

The paper explains the procedure of implementing Track & Trace solutions for manufacturers of explosives based on customer experiences. By using concrete examples, the process from project start to implementation is described. Lessons learned from the experiences of European explosives manufacturers are presented.

Feb 1, 2020