Search Documents

By A. G. Waters, N. J. Bristow

A comparative study was made of an untreated and a heated haematite ore and a sinter produced from a feed consisting of 100% ore, to study the influence on reduction behaviour of sinter bonding phases such as SFCA (silico-ferrite of calcium and alumina). Under low-temperature reduction conditions the order of increasing reducibility followed that of increasing porosity and surface area but under similar conditions at 900 degrees C the sinter exhibited higher reducibility than the ores even though the total porosity and chemical reducibility of the individual phases were lower. This behaviour can be explained in terms of the higher total porosity of the natural ore at low temperatures and the higher level of fine pores in the sinter at high temperatures due to the presence of SFCA, which acts to support the fine (c.0.1 micrometre) pores created by the reduction process. This leads to the conclusion that the main role of SFCA in sinter during high-temperature reduction is to maintain a high level of fine porosity. Some implications of this work for granule design and sintering practice are discussed

Apr 1, 1991

By V. E. Ross

A comparison was made of three methods for determining the contributions of true flotation and entrainment during batch flotation tests. In the first method size-by-size recoveries are measured in both the presence and the absence of a collector, a frother being present in both tests. In the second method the mass of solids and water recovered after a chosen time of flotation is varied by changing the rate of froth removal and the depth of the froth. The third method uses a transfer factor to describe the classification of solids and water, and hence the changes in the composition of the pulp, during a single flotation test. Batch flotation tests were carried out with artificial mixtures of pyrite and gangue, the amount of floated material recovered being calculated according to each of the three methods. The discrepancies betweeen the calculated amounts are analysed in terms of the assumptions that are made for the various methods and the most suitable conditions for the application of each method are identified

Dec 1, 1991

By R. Patel, J. Ephraim

The production of titanium dioxide (TiO2) from its minerals such as ilmenite is challenging, and subsequent isolation of titanium from TiO2 is even more difficult because of the metal-oxygen bond strength. Currently, titanium sponge is mainly produced via the Kroll process, which is energy intensive and generates large quantities of waste. A number of international research groups have come up with technologies for the production of titanium metal. However, none of them have been commercialised, because of engineering or economic issues. The team at Bradford have confirmed that ultra-pure titanium powders can be separated from TiO2 powder through metallothermic reduction and are working to scale up the process.

May 1, 2015

By B. Sonmez, B. Aksanl, S. Ersaym, I. F. Erkal, S. L. Ergun

The comminution circuit at the plant has experienced severe problems arising from a feed containing much larger amounts of clay and having a higher moisture content than expected. Three solutions were proposed: replacement of the crushing circuit by tooth roll-type crushers; using washing drums; and introducing primary autogenous/semi-autogenous millling instead of crushing. Computer simulations studied the effects of the first two solutions on the circuit capacity. Laboratory and industrial scale ball mill batch grinding tests were carried out. The parameters of a kinetic model were determined. The ball mill circuit was sampled and operating model parameters were calculated. The ability of batch grinding parameters to represent the operating conditions was studied. Tests failed to find acceptable model parameters, but parameters from an industrial size batch mill were found to be suitable for simulation studies. The simulations indicated that a continuous feed of -12 mm provided by tooth roll crushers would maintain the desired capacity. Increasing the feed size to -25 mm would reduce the capacity by 8-15%. The use of washing drums could also solve the capacity problem, but small fluctuations in water flow rates might result in problems of excess water in the grinding circuit.

Jan 4, 1993

For the convenience of those who are unfamilar with thermodynamics, the following brief description and explanation is given of the thermodynamical terms and methods used in this book. It must, however, be strongly emphasized that the account given below is not an introduction to chemical thermodynamics; its sole purpose is to give the reader a rough understanding of the methods used in the earlier chapters. For further information, reference must be made to the standard textbooks on chemical thermodynamics by Glasstone.

Jan 1, 1953

By R. Scheepers, J. E. Misiewicz, A. C. Fitzgerald

Discussion by A.C. Fitzgerald of the paper, published in Trans. IMM A, vol.104, 1995, p.B121-B135, is presented together with the authors' response. Fitzgerald points out a number of problems with the idea of mineralising fluids leaving no trace in the large volumes of rock traversed before depositing all minerals of value in a particular horizon or rock type with which the required isobaric or isothermic surface also coincides. He suggested that in the case of the Rooiberg tin deposits, the Lebowa Granites may be batholiths that reached the surface and were capped by sheets of their own volcanics. The authors agree that they had considered a possible syngenetic origin for the stratabound deposits, explain that no conclusive evidence for this could be found, discuss the relative ages of the sediments and volcanics of the Rooiberg Fragment and explain the role of its low-intensity deformation and flat dip in the coincidence of an isobaric-isothermic surface with the lithological stratification

Jun 18, 1905

By Eric Forssberg, Vigen Zeng

During mechanical grinding high intensity vibration is emitted that contains information on the mill's operating state. Tests, using a laboratory ball mill, studied the influence of operating parameters on the vibration signature. The parameters studied were: mill speed; powder filling; pulp density; grinding period; and pulp temperature. Vibration signals were detected by an accelerometer, amplified by a vibrometer and recorded onto digital audio tape. A digital oscilloscope converted the signals into IBM-compatible data format. Digital signal processing and multivariate data analysis were carried out with specially developed software. The power spectral density was estimated from the time-domain vibration signal. Four new latent variables were used to describe changes in the vibration spectra. A relationship was established between operating parameters and latent variables which could form the basis of a quick and automatic method of monitoring operating parameters in ball mill grinding.

Jan 4, 1993

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By D. D. Lei, H. Sevim

Long-term production planning in open-pit mines requires the determination of cut-off grade, mining and milling production rates, a mining sequence, mine life and ultimate pit limits. Since these variables interact in a circular fashion, a genuine solution to the problem necessitates their simultaneous determination. A methodology with this capability is described. This comprises a group of heuristic algorithms and an unconventional dynamic programming algorithm. The method is demonstrated using data for a gold deposit in the western USA

Jul 1, 1996

By C. A. Pickles, S. J. Splinter, J. Cameron

The addition of copper oxide to a borosilicate slag resulted in the breakdown of the silicate network and a dramatic decrease in viscosity. With increasing borax to silica ratio the viscosity was reduced by two mechanisms. First, rising sodium oxide content promoted cleavage of the Si-O bonds. Second, increasing boric oxide (B2O3) content increased the number of trigonal borate units that were converted to tetrahedral borate units by sodium oxide and copper oxide. The BO4(4-) tetrahedra decreased the local silicate symmetry, thus disrupting the silicate network and lowering the viscosity. The activation energy decreased with increasing temperature and increasing copper oxide content

Jun 13, 1905

By A. W. Fletcher

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J, Cahalan President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, December, 1970, pp. C247-52, and contributed remarks. Contributions are included from: Cahalan M.J., giving figures related to leaching Cu from pyrite at Rio Tinto 1880-1910; Noakes F.D.L.; Embling P.M.K.; Bradshaw A.V.; Le Roux N.W.; Kelly D.P.; and Tuovinen O.H. Questions were raised regarding impurity removal, effects of light and ultraviolet light on the bacteria, the economics of solvent extraction and the possibilities for other organisms or other metals

Dec 1, 1971

By N. T. Moxon, D. Mead, S. B. Richardson

A laboratory and theoretical study of air decks was carried out to assess the effects of the size and location of air-decks on fragmentation. The degree of fragmentation was found to depend on both factors. As the size of the air-deck increases the degree of fragmentation is reduced relative to a full column charge. However, the reduction is relatively small until a critical size is exceeded. The critical size depends on the strength and structure of the surrounding material. A critical air-deck length of 30-35% of the original explosive column was determined for the model materials used in the study. A theoretical explanation of the results was derived based on pressure decay rate relationships. The location of the air-deck also influences fragmentation. The interaction and oscillation of the two shock fronts from the top and bottom charges mean that mid-column air-decks produce better fragmentation for the same air-deck length and explosive loading as top-column or bottom-column air-decks.

Jan 4, 1993

Jan 1, 1984

By T. Sharma, T. C. Rao

Laboratory studies have been carried out on acid leaching as a possible route for the extraction of potassium from glauconitic sandstone. Leaching efficiencies with sulphuric, hydrochloric and nitric acids were investigated. The effects on potassium dissolution of temperature, concentration and type of acid, stirring speed and leaching time were also studied. The results show that it is possible to recover 87.5, 93 and 85% potassium with 5 M H2SO4, HCl and HNO3, respectively. During the initial stages of the sulphuric acid leaching process the chemical reaction at the mineral surface is the rate determining step, whereas during the later stages diffusion through the product layer is rate-controlling. Overall, the process follows a mixed-control model that includes both chemical reaction and diffusion. The activation energy for the dissolution of K was found to be in the range 25.79-106 kJ/mol.

Jan 12, 1992

By R. R. Tatiya

The following procedure was used to determine cut-off grades: define the orebody profile; plan the stope layout and quantify the work involved; formulate equipment-performance norms; calculate unit costs; input process recoveries and metal prices; and calculate the cut-off grade. Use of the method is illustrated using data from a copper mining complex in India. Results from the study led to the following conclusions for underground mines in general. Cut-off dependent costs vary significantly with the stoping method employed, orebody thickness, the degree of mechanisation and the working efficiencies of the workforce and equipment. This applies even within the same deposit. Sub-level stoping and its variants can be operated at a lower cut-off grade than cut-and-fill and its variants. Thinner orebodies affect cut-off grades adversely, but with thinner orebodies very little further reduction in cut-off grade can be achieved once a certain minimum width has been exceeded. For the same stoping method and in the same mine the cut-off grade varies with the degree of mechanisation. Labour-intensive methods require higher cut-off grades. An allowance for working efficiency should be made when calculating cut-off grades. Higher process recoveries allow a significant lowering of cut-off grades

Jul 1, 1996

By F. Reich, S. L. Chryssoulis, K. G. Stowe

The surface chemistry of particulates from mineral processing streams can be determined by laser-probe microanalysis. The small area of analysis (2-30 micrometres) enables the surfaces of individual grains to be characterised. Conclusions are based on data acquired from a statistically significant number of grains of a given type. Maps showing the distribution of elements on the surface of mineral particulates can be obtained by time-of-flight secondary ion mass spectrometry. The importance of such analyses in understanding the response of minerals to beneficiation practices is discussed with reference to three examples. The first relates to the loss of selectivity in the differential flotation of a base-metal ore, the second to the different flotabilities of coarse- and fine-grained pentlandite from a Cu-Ni ore and the third concerns the preg-robbing effects of organic matter in a carbonaceous gold ore.

Jan 4, 1992

By Asfa-Wossen L.

Davy saw science to be the ultimate truth. He loved the utility and permanence of it and the feeling of progression. He was a bold chemist and an inventor, but he thought like a writer

Feb 1, 2015

By M. A. Bussell, G. S. Camm

The study included lode zones at Wheal Pendarves, South Crofty and Rosevale tin mines. Fluid inclusion-containing microfractures are a common feature of the granites and typically show a preferred orientation over quite a large area. The close proximity of a dominant vein or fault controls their density and orientation. They are important pathways for fluids and provide a marker for palaeo-fluid flow. Overprinting provides a reliable representation of the evolution of the hydrothermal fluids in a vein system from early magmatic fluids to late-stage meteoric and basinal brine input. Measurement of microfracture orientation allows estimation of the regional stress regime during a specific hydrothermal event. Since micro- and macro-structures can generally be reliably correlated, these studies assist in modelling the detailed development of complex vein systems. Microfracture density is a good measure of palaeo-permeability, with implications for control of wallrock alteration. The determination of the location and density of microfractures can assist the mine geologist in identifying the location of potentially economic vein structures where macroscopic markers are absent

Aug 1, 1996

By D G. Jefferies

This paper covers National Grid's role in the electricity market, the growth of competition in both generation and supply in that market, and the resulting impact on fuel usage, prices and the environment. It also considers other, external influencing factors on the electricity supply industry, as well as the growing trend towards globalization.

Jan 12, 1997

By Winmill T. F.

(Paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916.) The conclusions reached in this paper may be summarized briefly as follows: (1) The method of estimating moisture in coal by determining the loss in weight of a sample heated to 105°-110° Cent, in an air-bath for an hour is untrustworthy, the results so obtained being too low. (2) Dried coal has a very considerable power of absorbing moisture, and a sample, after being dried, must be protected instantly if it is to remain free from moisture. (3) A fairly accurate estimation may be made by heating the coal in a current of dry air at 105° to 110° Cent., and collecting the moisture evolved. (4) In cases in which it is proposed to use the dried coal for any further experiments, the drying must be done in the absence of oxygen, and this can be done simply and quickly by the vacuum method now described

Dec 1, 1916