Search Documents

By Song Z. Guo

Calcite and magnesite are both carbonate minerals and their crystals belong to trigonal system. Flotation tests were carried out to investigate the flotation behaviors of calcite and magnesite. The test results show that the floatability of calcite and magnesite under different grinding environment had obvious differences. The floatability of calcite using sodium oleate as collector after dry grinding is better than wet grinding, but the floatability of magnesite after wet grinding is better than dry grinding. The XPS surface elements test and zeta potential measurement show that, wet and dry grinding process makes the distribution difference of surface anion and metal cation, then influence the floatability of the two carbonate minerals using sodium oleate as collector. Difference of the carbonate crystal structure and solubility properties was also investigated. Research shows that crystal structure difference of calcite and magnesite causes the difference of solubility, which can influence the flotation behaviors under different grinding environment. Keywords: carbonate mineral, crystal structure, solubility properties, flotation, surface character

Sep 1, 2012

By Markus A. Reuter, Yongxiang Yang, James R. Post

The packed coke bed in the lower part of an iron making blast furnace, the dead man, dissolves slowly in a pool of hot metal, which is tapped regularly. The coke particles of the dead man not only exhibit a size distribution, but also their size distribution is non-uniform throughout the dead man and as a result, the porosity of the dead man is non-uniform. This causes the flow of hot metal through the dead man to be irregular and non-uniform, bringing about channelling in the coke bed. Channelling is detrimental to the refractory lining life of the hearth of a blast furnace. Using population balance modelling and a porosity model it is possible to keep track of the local changes in size distribution and bed porosity during dissolution of coke particles. Numerical simulations show that carbon dissolution from a packed coke bed (with particles which exhibit a size distribution) increases the average porosity, decreases the mean particle size and changes the size distribution to a distribution with a smaller size range. Influence of the type of initial size distribution (mean, variance) is investigated. The calculated changes in porosity are used to dynamically adapt the flow and the mass transfer (kinetics) during calculations. This approach provides the possibility to implement dynamic porosity calculations for CFD applications, and thus simulate the results of various coke types and particle size distributions on dissolution and flow behaviour.

Jan 1, 2003

By A. P. Purgin, M. G. Viduetsky, I. F. Garifulin

"The combined treatment process for mine, tailings storage facility, quarry, circulating, and waste water in the mining and metals industry brings together the conventional chemical treatment processes and pneumatic flotation cells of the KFM series. The key principle of the process is preparing the water for treatment by saturating with finely dispersed air bubbles in the flotation cell blowers. Gas-air lift dispersers located in the lower part of the cell body additionally saturate the cell’s contents with finely dispersed air. Due to the residual content of flotation agents in the treated water, hydroxide ion-air aggregates form at the aerator outlet, supporting the efficient precipitation of hydroxide ions of heavy non-ferrous metals, calcium and magnesium ions. This process was tested in the pilot plant KFM-180 with a raw (untreated) water capacity of up to 18 m3/h per 1 m3 of the flotation cell volume using a mixture of the tailings storage facility and mine water from JSC Safyanovo Copper. The treatment process included raw water treatment with lime, aeration in KFM cells, and filtration in a sorbent bed. The content of metal ions in the treated water is lower than in the feed water by a factor of up to 170,000 and approaches the standards: aluminum 0.016-0.02 mg/l, copper 0.0043-0.0045 mg/l, zinc 0.049-0.052 mg/l. circulating water of Soryin Tailings Storage Facility at JSC Svyatogor. The treatment process included raw water treatment with lime and alkali, aeration in KFM cells, and filtration in a sorbent bed. The content of metals in the treated water is lower than in the feed water by a factor of up to 9000: copper 0.022 mg/l, zinc 0.012 mg/l, iron 0.012 mg/l, manganese 0.015 mg/l, nickel 0.132 mg/l, arsenic 0.016 mg/l. Water hardness is significantly lower: calcium - 12.6 mg/l, magnesium - 1.1 mg/l. This process can be used in the treatment of mine, quarry, tailings storage facility, and circulating water at mining and non-ferrous metals projects."

Jan 1, 2018

By Manochehr Oliazadeh

"Water shortage becomes a major challenge in mining industry. The best example is Chile where the Chilean authorities declared a state of emergency in 2012. Depletion of high grade ore-bodies necessitates the use of low grade ores. If the demand for metals remains constant, more low-grade ores need to be mined to produce the same tonnages of metals. This increases the water demand in mining industry. Mining industry competes with other industries such as agriculture and manufacturing. Agriculture and manufacturing consume 1500 and 2300 billion m3 water respectively. The global use is 4500 billion m3 while the mining uses 80 billion m3 of water per annum.To tackle the water challenges in mining industry and also avoid competing with other users for fresh water, many efforts have been made, including using lower quality waters to reduce the fresh water consumption in ore processing. Saline water or hyper saline water from seas or the ground is accessible; however the cost of desalination is remarkable. Desalination plants and associated pipelines and pumps capital cost can easily exceed $ 500 million. Saline water will certainly increase the operating costs due to high wear rate of mechanical equipment but at current situation of mining industry spending all this money upfront does not look attractive. Desalination leaves salt on land at mine site which may create environmental issues.Dry processing can be a solution for water shortage in mineral processing. Wet processes dispose tailings on land with little or no agricultural productivity. It also may contaminate surface and ground water and generate dust. This paper reviews the water consumption by various mineral commodities, discuss briefly about recent of application of salt water in mineral processes and finally discuss about dry processes as alternative solution for water shortage in mining industry."

Jan 1, 2014

By Z. F. Hu

Tourmaline has the characteristics of piezoelectricity, thermoelectricity, spontaneous polarization and far-off infrared radiations. Ultra-fine powders of tourmaline have extensive applications in the fields of electron, chemical and environment protection, as well as health protection. The preparation technology of ultra-fine tourmaline powder is discussed. The key equipment of a pilot plant for producing ultra-fine tourmaline powder with jet mill and stirred ball mill is described. Using this pilot plant facility it is possible to produce tourmaline powder with particle size smaller than 100 nm, and a continuous production process can be realized. The final powder product has many superior performance such as high whiteness and large specific surface area, and it?s a negative ions emission can reach the value of 7190 ions per cubic centimeter.

Jan 1, 2014

By N. Naudé

The theory on particles displacement subjected to upwards and settling movements in water, using a water pulse, is described in literature, but very little experimental data is available to verify these theoretical ideas. The aim of this research work was to visualize the displacement of solid particles in a mixture of water and solid particles created with the aid of water pulses in the Mineral Density Separator. From the literature it is known that lighter particles are subjected to higher levels of displacement than heavier particles, and when the particles then settled down, layers of material are formed ac-cording to the densities of the material. By removing the individual material layers, the materials can then be separated according to their densities. During this study the individual material layers were investigated regarding the density and size distribution in that specific density layer. It is important for this project to have a statistical prediction of the ?real? flow of the particles with different density and size distribution, inside the Mineral Density Separator. The information gathered during this study will be used to show the correlation between a two dimensional model of the particle flow and that of the real three dimensional flow inside the Mineral Density Separator.

Jan 1, 2014

By Thi Hien Tran, Huy Hoan Nguyen, Thi Thu Hien-Dinh, Hong Son Nguyen, Duy Anh Dao

"Lithium discovered in La Vi deposit, Quang Ngai province in the Central of Vietnam was estimated with a reserve of approximately 1.5 million tones of lithium ore, which was characterized by mainly lepidolite with muscovite, albite, and quartz. This study investigated reasonable flowsheet and optimal conditions of enrichment technology for lepidolite from the mined ore by flotation process, and producing Li2CO3 and LiCl from lepidolite concentrate by hydrometallurgical process. The significant conditions for froth flotation of lithium ore including particle size, pH of ore slurry, pulp density, chemical spending (collectors, activators, depressants, and frothers), stirring and flotation time were investigated. The identified reasonable flowsheet and optimal conditions for froth flotation the La Vi lithium ore processed lepidolite concentrate containing up to 4 wt.% Li2O with a recovery of 87.61 wt.%. The processes of sulfation roasting lepidolite concentrate using FeSO4.7H2O, then leaching in H2SO4 solution, and removing impurities were carried out to prepare a pure lithium-bearing solution for producing Li2CO3 and LiCl. The products containing 99.05 wt.% of Li2CO3 and 99.02 wt.% of LiCl were obtained with recoveries of 82.97 wt.% and 85.77 wt.%, respectively. The obtained results indicated that lithium ore in La Vi deposit can be processed to produce commercial lithium products and lead the study to develop technology for a new industry of lithium processing in Vietnam.INTRODUCTION Lithium is the lightest metal, which has many superior properties in both metal and compound (such as Li2CO3, LiCl...) states since its discovery in 1817 by Swedish chemist Johan August Arfwedson. Lithium is a favourable material for many high technology fields such as aerospace industry and chemical industry. Some industrial fields which present the main consumptions of lithium include ceramic, glass, aluminum alloy, lubricants, rechargeable Li-ion batteries, synthetic rubber, and pharmaceuticals. The worldwide production of lithium in 2014 was 31,700 tones, continually increased in 2015 of 5% presented 32,500 tones (USGS, 2016). The demand for lithium tends to increase because of the raising in consumption of lithium batteries. Lithium is mined from salar brines, mainly in Chile and Bolivia, but also from granites and pegmatites, which contain minerals with high lithium content such as spodumene - LiAlSi2O6 (Heinrich et al., 1978; Linnen et al., 2012); petalite - LiAlSi4O10 (Sitando & Crouse, 2012); zinnwaldite - KLiFe2+Al(AlSi3O10)(F,OH)2 (Paukov et al., 2010; Kondás J. & Jandová J., 2006); lepidolite - K(Li,Al)3(Si,Al)4O10(F,OH)2 (Luong et al., 2013); and amblygonite - LiAlPO4F (Garrett, 2004)."

Jan 1, 2018

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By S. J. Neethling

"Liberation is a key driver in all mineral separation processes as it limits the maximum possible grade for a given recovery. In flotation, this is further complicated by the fact that it is surface exposure of the floatable minerals that determines the ultimate performance. Liberation, grade and surface exposure are commonly quantified using Scanning Electron Microscopy coupled to Energy Dispersive X-ray spectroscopy (SEM/EDX) analysis of polished sections. The intrinsically 2D nature of this technique can result in significant sampling errors and stereological effects that can affect the quantification of the ore’s textural characteristics. X-ray micro-Tomography (XMT) is an imaging method that can non-invasively and non-destructively delineate ore fragments in 3D, thus providing an alternative method that eliminates the need for stereological corrections and readily provides surface exposure. A methodology and automated algorithm were designed for extracting this information from images of closely packed particles, thus allowing samples containing a large number of particles to be assessed.The main drawback of XMT is that, unlike SEM/EDX, it cannot directly measure the mineralogy of the sample, instead producing a 3D X-ray attenuation map. We therefore also present an algorithm for calibrating the thresholding of the XMT images based on SEM/EDX images of sections through the same sample, thus allowing the liberation analysis to be carried out on a 3D mineral map in which the uncertainty in the mineral assignment is small and statistically quantified.The methodology was tested on low grade porphyry copper ore as this is both an industrially relevant and traditionally difficult system to quantify using XMT due to the similarity in the X-ray attenuation of the sulphide species, especially the pyrite and chalcopyrite. As each 3D volume imaged contain 100-1000s of grains, large data sets can be readily produced. By dividing these particles into classes based on both their surface exposure and grade, the extent to which there is preferential breakage of the particles can be assessed—an important consideration if sufficient surface liberation for good flotation performance is to be achieved at coarser particle sizes. It is also shown that erroneous conclusions can be drawn when basing the analysis on 2D sections through the particles."

Jan 1, 2018

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014

By Y. Lin

It is difficult to remove arsenic and bismuth from antimony in the process of crude electro refining. The electro refining of antimony has been studied using ammonium fluoride-antimony sulphate electrolyte system. The Influence of temperature, current density and additives on arsenic and bismuth removal from crude antimony has been investigated in this paper. Optimum process parameters, namely, temperature of 25?, current density of 400A/m2, distance between anode and cathode of 50mm, electrolytic period of 24 hours, oxalic acid dosage of 10g/L and complexon III dosage of 0.2 g/L have been ascertained.

Jan 1, 2014

By H. Matsuoka, M. Kawata, K. Haga, K. Mitsuhashi, C. Tokoro, A. Shibayama, R. Kawarabuki

"The mineral surface characteristic is important for the flotation because it affects the flotation behavior of the mineral. Conventionally, in the flotation process for Cu sulphide ores, the degree of ore floatabilities varies depending on the mineral phase such as chalcopyrite, bornite, or chalcocite. Therefore, mineral surfaces are treated with activators and depressants to control the floatability of target minerals and obtain high recovery performance. There are lots of flotation reagents which have many effects on ores depending on ore characteristics and conditioning methods. For example, sodium hydrosulphide (NaHS) as activator is known to have the effect of resulfurizing and activating oxidized surface of chalcocite and bornite. On the other hand, NaHS is reported to depress chalcopyrite floatability. In this study, the evaluation of mineral surfaces was conducted to predict flotation behavior. Activation of Cu minerals (chalcocite, bornite, and chalcopyrite) by NaHS was experimented. The three Cu minerals were treated in two steps. Firstly, they were oxidized in the drying oven. Secondly, they were treated with NaHS solution. After each treatment step, each mineral was measured by contact angle apparatus then analyzed by X-ray photoelectron spectroscopy (XPS). The results of surface characteristics after oxidation and NaHS treatment were utilized to accomplish the study’s objective. INTRODUCTIONCopper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are well-known abundant copper-containing minerals. Generally, these minerals are recovered and concentrated via collector flotation. In flotation, the wettability of the mineral surface is an important factor in its recovery. When the surface is hydrophobic, the mineral has high floatability and when the surface is hydrophilic, it has low floatability. Usually, Cu sulfide minerals have high floatability. However when their surfaces are oxidized, their floatability becomes lower in flotation. In this case of surface oxidation occurrence, activators are added before flotation to modify the surface property of the Cu sulfide minerals so that they can be floated at a certain flotation condition. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao et al. (2018) reported that NaHS is often used as sulfurizer for oxidized sulfide minerals (Becker et al., 2014, Clark et al., 2000, Newell et al., 2006, 2007, Newell and Bradshaw, 2007). Although the floatability of Cu sulfide minerals was raised by adding NaHS generally, the results of this flotation study showed that the flotation behaviors of mixed chalcocite, bornite, and chalcopyrite were different. Therefore, it was considered that NaHS works differently for each mineral."

Jan 1, 2018

By Yuri Yemelianov, Stanislav Balikov, Alexander Epiforov, Andrey Boldyrev, Andrey Bogorodsky

"Test work was carried out using copper gold-bearing flotation concentrate with 6.85%Cu, 14.30%Fe, 20.70%S and 2.34%As. Gold and silver grade in the concentrate is 54.6 g/t and 92 g/t, respectively. Gold and copper are valuable components in the concentrate. Gold is partially associated with pyrite and fahlores. Copper in the concentrate can be found as tennantite (Cu12As4S13). The 71% of gold from the flotation concentrate is recoverable by cyanidation with simultaneous cyanide consumption in the amount of 96 kg/t. The major reason of refractoriness is that gold is fine encapsulated into sulfides and the presence of cyanicide-copper. The concentrate ground as much as 95% minus 10 µm was treated using low-temperature POX at the temperature of 100±5°C, L:S ratio of 5:1 and the process time of 1-5 hours. Residual sulfide sulfur in the cake is 2.28% which is 89% sulfide oxidation. The highest copper recovery to POX solution is 91%. It was found that gold recovery to cyanide solution is 85-94% during alkaline pre-treatment of POX cakes followed by cyanidation. In this case, cyanide and lime consumption is 75-90 kg/t and 120 kg/t, respectively. In order to recover precious metals from POX cakes leaching using sodium sulfite was carried out. Test work was conducted at varied reagent concentration, L:S ratio and leaching time. Gold and silver recovery achieved was 85-95% and 59-63%, respectively."

Jan 1, 2014

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By Sergey Romanenko, Tatyana Aleksandrova, Karen Arustamian

"Current status of question about grinding stage effect to electrochemistry parameters of operation preparation slurry before intermediate selective flotation was assessed in the present scientific work. Needs of more detail study chemical reactions in the slurry preparation and flotation processes were shown. The ores are polymetallic sulphide type and the one are most difficult for mineral processing. The methodology allows increase information base during floatation tests. Ionometric methods and elements of neural network have been used in the study of mineral processing questions.We have also identified the relationship between the received values of the electrochemical parameters and the technological results in selective flotation. The optimal values of the electrochemistry parameters in operation of the preparation slurry before selective flotation has been found. The main effect of using the proposed methodology is to obtain scientifically based solutions to improve the technology parameters of flotation polymetallic sulfide ores. Challenging issue of selectivity of sulphide-polymetallic ores will be considered using case study of sulphidepolymetallic ores. It was shown that several factors are formed in ore grinding: formation of hydroxyl oxides of iron compounds, copper cation leaching, metal-sulphide and metal-sulphite complexes formation. The chemistry was revealed for current processes in slurry preparation operation before selective flotation. Quantitative assessment of interrelations between electrochemical parameters of slurry and process performance was given with using electrochemical control methods. Neuron network-based model was estimated based on data array and was allowed to establish optimum electrochemical conditions of metal-sulphite complex formation to provide maximum efficiency of selective flotation.INTRODUCTIONPhysical and chemical processes that take place in ore grinding have a significant impact on flotation selectivity and can cause low selectivity of the flotation process. Today this issue is given much attention. In the paper [1] it is pointed out that sulphide oxidation products and slurry components, such as sulphide ions, metallic iron and its oxidation products, have effect on flotation performance. So, metallic iron has impact on metal-sulphite complex formation as a result of oxidation-reduction reactions as follows:"

Jan 1, 2018

By Gabriel Barrios, Juan Pérez-Prim, Marcelo Tavares

"The application of High Pressure grinding Rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits generally supporting this trend are better energy efficiency, improved grinding capacity, less sensitivity to ore grindability variations and higher metal recovery in downstream processes such as heap leaching and flotation. The HPGR machine comprises a pair of counter-rotating rolls mounted in a sturdy frame. One roll is fixed in the frame, while the other is allowed to float on rails and is positioned using pneumohydraulic springs. The feed material is introduced in the gap between the rolls and is crushed by the mechanism of interparticle breakage. Comminution performance is largely determined by the pressure exerted on the bed of particles by the floating roll hydraulic system. The operating bed pressure depends on the hydraulic system start-up parameters and the loading response of the feed material. The work describes how the coupling of the multi-body dynamic simulation with Discrete Element Method in which particle breakage is described using the particle replacement method, can be effectively used to predict the performance of the HPGR. The model considers important variables as the HPGR rolls geometry and design, the hydraulic spring system start-up parameters and the material loading response, to describe operational key outputs as material throughput, operating gap and roller pressure distribution. The preliminary version of the model has been used to predict the effect of material properties on the operating gap and the load distribution on the surface of the rolls, demonstrating that it can describe qualitatively the HPGR operation, indicating that the model will be a power full tool for the simulation and selection of industrial HPGR units."

Jan 1, 2014

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By G. J. Feng

Based on detailed theoretical analysis of coarse floatation and three-phase froth, a laboratory system which contains a new type of froth floatation equipment is established. Through water experiment, the relationship among floatation dynamics parameters of the equipment is studied and the best work parameters are educed too. Based on all of above, Slurry test is carried out in a copper concentration plant. Granule between 0.28~0.45mm can be reclaimed successfully. The slurry test proves that to separate coarse minerals in froth floatation equipment is a kind of effective method, it is well worth to make a further study.

Jan 1, 2014